PI5C16212 Ω) PI5C162212 (25Ω 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 24-Bit Bus Exchange Switch Product Features Product Description Near-zero propagation delay 5-ohm switches connect inputs to outputs Direct bus connection when switches are ON Ultra-low quiescent power (0.1µA typical) Ideally suited for notebook applications Industrial operating temperature: 40°C to +85°C Packages available: 56-pin 173-mil wide plastic TVSOP (K) 56-pin 240-mil wide thin plastic TSSOP (A) 56-pin 300-mil wide plastic SSOP (V) Pericom Semiconductors PI5C series of logic circuits are produced using the Companys advanced submicron CMOS technology. The PI5C16212 and PI5C162212 are 24-bit bus exchange switches designed with a low ON resistance allowing inputs to be connected directly to outputs. This device operates as a 24-bit bus switch or a 12-bit exchanger that provides data exchanging between the four signal ports via the data select pins (S0-S2). To reduce noise resulting from reflections, the PI5C162212 has a built-in 25-ohm series resistor that eliminates the need for an external terminating resistor. Product Pin Configuration Logic Block Diagram S0 1A1 ONE OF TWELVE CHANNELS 1A2 1 B1 1A1 2 A1 2A2 3A1 3A2 GND 4A1 1 B2 1A2 4A2 5A1 FLOW CONTROL 5A2 6A1 S0 S1 S2 6A2 7A1 7A2 VCC 8A1 GND Truth Table Function 8A2 S2 S1 S0 A1 A2 Disconnect L L L Z Z A1 to B1 L L H B1 Z A1 to B2 L H L B2 Z A2 to B1 L H H Z B1 A2 to B2 H L L Z B2 Disconnect H L H Z Z A1 to B1, A2 to B2 H H L B1 B2 A1 to B2, A2 to B1 H H H B2 B1 9A1 9A2 10A1 10A2 11A1 11A2 12A1 12A2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 56-Pin A, K, V 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 S1 S2 1B1 1 B2 2B1 2 B2 3B1 GND 3 B2 4B1 4 B2 5B1 5 B2 6B1 6 B2 7B1 7 B2 8 B1 GND 8 B2 9B1 9 B2 10B1 10B2 11B1 11B2 12B1 12B2 Product Pin Description Note: 1. H = High Voltage Level L = Low Voltage Level Z = High Impedance 1 Pin Name I/O De s cription S0- S2 I Select Inputs xAx I/O Bus A xBx I/O Bus B PS7023F 12/12/01 PI5C16212/162212 24-Bit Bus-Exchange Switch 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Maximum Ratings (Above which the useful life may be impaired. For user guidelines, not tested.) Storage Temperature .............................................. 65°C to +150°C Ambient Temperature with Power Applied ..............40°C to +85°C Supply Voltage to Ground Potential .......................... 0.5V to +7.0V DC Input Voltage ....................................................... 0.5V to +7.0V DC Output Current ................................................................ 120mA Power Dissipation ....................................................................... 1W Note: Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. Recommended Operating Condition Parame te r D e s cription M in. M ax. VCC Supply Voltage 4 5.5 VIH High- Level Input Voltage 2 VIL Low- Level Input Voltage 0.8 TA O perating Free- Air Temperature 40 85 Units V °C DC Electrical Characteristics (Over the Operating Range, TA = 40°C to +85°C, VCC = 5V ±10%) Parame te rs De s cription Te s t Conditions (1) M in. Typ(2) M ax. VIH Input HIGH Voltage Guaranteed Logic HIGH Level 2.0 VIL Input LOW Voltage Guaranteed Logic LOW Level 0.5 Input Current VCC = Max., VIN = VCC or GND ±1 VCC = 0, VIN = VCC 10 II Units V 0.8 µA IOZH High Impedance Output Current 0 A, B VCC ±1 VIK Clamp Diode Voltage VCC = Min., IIN = 18mA 0.7 1.2 V A (B) = 0V, B (A) = VCC 100 mA 150 mV Current(3) IOS Short Circuit VH Input Hysteresis at Control Pins RON Switch On Resistance(4) VCC = Min., VIN = 0.0V, ION = 64mA 16212 5 7 162212 20 28 40 VCC = Min., VIN = 2.4V, ION = 15mA 16212 12 162212 20 35 48 Ω Capacitance (TA = 25°C, f = 1 MHz) Parame te rs (5) Te s t Conditions Typ. M ax. Input Capacitance VIN = 0V 3 6 CO F F A/B Capacitance, Switch Off VIN = 0V 6 14 CO N A/B Capacitance, Switch On VIN = 0V 8 30 C IN De s cription Units pF Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device. 2. Typical values are at VCC = 5.0V, TA = 25°C ambient and maximum loading. 3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second. 4. Measured by the voltage drop between A and B pin at indicated current through the switch. ON resistance is determined by the lower of the voltages on the two (A,B) pins. 5. This parameter is determined by device characterization but is not production tested. 2 PS7023F 12/12/01 PI5C16212/162212 24-Bit Bus-Exchange Switch 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 Power Supply Characteristics Parame te rs ICC ∆ICC(3) ICCD Te s t Conditions (1) De s cription M in. Typ.(2) M ax. Units Quiescent Power Supply Current VCC = Max. VIN = GND or VCC 0.1 3.0 µA Supply Current per Input @ TTL HIGH VCC = 3.6V VIN = 2.7V(4) 0.2 mA Supply Current per Input per MHz(5) SN = GND, Control Input Toggling 50% Duty Cycle VCC = Max., A & B Pins Open 0.25 mA/ MHz Notes: 1. For conditions shown as Max. or Min., use appropriate value specified under Electrical Characteristics for applicable device. 2. Typical values are at VCC = 5.0V, +25°C ambient. 3. This is the increase in supply current for each input that is at the specified TTL voltage level rather than VCC or GND. 4. Per TTL driven input (VIN = 2.7V, control inputs only); A and B pins do not contribute to ICC. 5. This current applies to the control inputs only and represent the current required to switch internal capacitance at the specified frequency. The A and B inputs generate no significant AC or DC currents as they transition. This parameter is not tested, but is guaranteed by design. PI5C16212 Switching Characteristics over Operating Range PI5C16212 Parame te rs Conditions (1) D e s cription tPLH tPHL Propagation Delay(2,3), xAx to xBx, xBx to xAx tPLH tPHL Propagation Delay, S to Ax or Bx tPZH tPZL Bus Enable Time, S to xAx or xBx tPHZ tPLZ Bus Disable Time, S to xAx or xBx CL = 50pF RL = 500 ohms Com. M in. M ax. 0.25 1.5 7.5 Units ns 1.5 7.0 1.5 6.5 PI5C162212 Switching Characteristics over Operating Range PI5C162212 Parame te rs Conditions (1) D e s cription tPLH tPHL Propagation Delay(2,3), xAx to xBx, xBx to xAx tPZH tPZL Bus Enable Time, S to xAx or xBx tPHZ tPLZ Bus Disable Time, S to xAx or xBx CL = 50pF RL = 500 ohms Com. M in. M ax. 1.25 1.5 7.0 1.5 6.5 Units ns Notes: 1. See test circuit and waveforms. 2. This parameter is guaranteed but not tested on Propagation Delays. 3. The bus switch contributes no propagational delay other than the RC delay of the ON resistance of the switch and the load capacitance. The time constant for the switch alone is of the order of 0.25ns for 50pF load. Since this time constant is much smaller than the rise/fall times of typical driving signals, it adds very little propagational delay to the system. Propagational delay of the bus switch when used in a system is determined by the driving circuit on the driving side of the switch and its interaction with the load on the driven side. 3 PS7023F 12/12/01 PI5C16212/162212 24-Bit Bus-Exchange Switch 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 56-Pin 173-Mil Wide Plastic TVSOP (K) Package 56 4.30 4.50 .169 .177 0.09 0.20 .0035 .008 1 .441 .449 0.45 .018 0.75 .030 .031 .041 0.80 1.05 11.20 11.40 .252 BSC 6.4 SEATING PLANE .016 BSC 0.40 X.XX X.XX .047 1.20 Max. .002 .006 0.05 0.15 .005 .009 0.13 0.23 DENOTES DIMENSIONS IN MILLIMETERS 56-Pin 240-Mil Wide Thin Plastic TSSOP (A) Package 56 .236 .244 1 .547 .555 6.0 6.2 13.9 14.1 1.20 .047 Max. SEATING PLANE .004 0.09 .008 0.20 .0197 BSC 0.50 X.XX DENOTES DIMENSIONS X.XX IN MILLIMETERS .007 .011 0.17 0.27 4 .002 .006 0.05 0.15 0.45 .018 0.75 .030 .319 BSC 8.1 PS7023F 12/12/01 PI5C16212/162212 24-Bit Bus-Exchange Switch 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012 56-Pin 300-Mil Wide Thin Plastic SSOP (V) Package 56 .291 .299 7.39 7.59 .396 .416 10.06 10.56 Gauge Plane .02 .04 0.51 1.01 .010 0.25 1 .720 18.29 .730 18.54 .015 0.381 x 45˚ .025 0.635 .008 0.20 Nom. .110 2.79 Max .008 .0135 0.20 0.34 .025 BSC 0.635 X.XX DENOTES DIMENSIONS X.XX IN MILLIMETERS 0-8˚ .008 0.20 .016 0.40 Ordering Information Orde ring Code Package Name Package Type Te mpe rature Range PI5C16212K K 56 56- pin TVSO P 40 to 85°C PI5C162212K K 56 56- pin TVSO P 40 to 85°C PI5C16212A A56 56- pin TSSO P 40 to 85°C PI5C162212A A56 56- pin TSSO P 40 to 85°C PI5C16212V V56 56- pin SSO P 40 to 85°C PI5C162212V V56 56- pin SSO P 40 to 85°C Pericom Semiconductor Corporation 2380 Bering Drive • San Jose, CA 95131 • 1-800-435-2336 • Fax (408) 435-1100 • http://www.pericom.com 5 PS7023F 12/12/01