ETC TPA721DGNR

TPA721
700-mW MONO LOW-VOLTAGE AUDIO POWER AMPLIFIER
SLOS231C – NOVEMBER 1998 – REVISED APRIL 2001
D
D
D OR DGN PACKAGE
(TOP VIEW)
Fully Specified for 3.3-V and 5-V Operation
Wide Power Supply Compatibility
2.5 V – 5.5 V
Output Power for RL = 8 Ω
– 700 mW at VDD = 5 V, BTL
– 250 mW at VDD = 3.3 V, BTL
Integrated Depop Circuitry
Thermal and Short-Circuit Protection
Surface-Mount Packaging
– SOIC
– PowerPAD MSOP
D
D
D
D
SHUTDOWN
BYPASS
IN+
IN–
1
8
2
7
3
6
4
5
VO –
GND
VDD
VO +
description
The TPA721 is a bridge-tied load (BTL) audio power amplifier developed especially for low-voltage applications
where internal speakers are required. Operating with a 3.3-V supply, the TPA721 can deliver 250-mW of
continuous power into a BTL 8-Ω load at less than 0.6% THD+N throughout voice band frequencies. Although
this device is characterized out to 20 kHz, its operation was optimized for narrower band applications such as
wireless communications. The BTL configuration eliminates the need for external coupling capacitors on the
output in most applications, which is particularly important for small battery-powered equipment. This device
features a shutdown mode for power-sensitive applications with a supply current of 7 µA during shutdown. The
TPA721 is available in an 8-pin SOIC surface-mount package and the surface-mount PowerPAD MSOP, which
reduces board space by 50% and height by 40%.
VDD 6
VDD
RF
VDD/2
Audio
Input
RI
CI
4
IN –
3
IN+
2
BYPASS
CS
–
VO+ 5
+
CB
–
VO– 8
+
700 mW
7
GND
From System Control
1
SHUTDOWN
Bias
Control
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PowerPAD is a trademark of Texas Instruments.
Copyright  2001, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
TPA721
700-mW MONO LOW-VOLTAGE AUDIO POWER AMPLIFIER
SLOS231C – NOVEMBER 1998 – REVISED APRIL 2001
AVAILABLE OPTIONS
PACKAGED DEVICES
TA
SMALL OUTLINE†
(D)
MSOP
Symbolization
MSOP‡
(DGN)
– 40°C to 85°C
TPA721D
TPA721DGN
ABC
† In the D package, the maximum output power is thermally limited to 350 mW; 700 mW peaks
can be driven, as long as the RMS value is less than 350 mW.
‡ The D and DGN packages are available taped and reeled. To order a taped and reeled part, add
the suffix R to the part number (e.g., TPA301DR).
Terminal Functions
TERMINAL
NAME
NO.
I/O
DESCRIPTION
I
BYPASS is the tap to the voltage divider for internal mid-supply bias. This terminal should be connected
to a 0.1-µF to 2.2-µF capacitor when used as an audio amplifier.
BYPASS
2
GND
7
IN –
4
I
IN – is the inverting input. IN – is typically used as the audio input terminal.
IN+
3
I
IN + is the noninverting input. IN + is typically tied to the BYPASS terminal.
SHUTDOWN
1
I
SHUTDOWN places the entire device in shutdown mode when held high (IDD < 7 µA).
VDD
VO+
6
5
O
VDD is the supply voltage terminal.
VO+ is the positive BTL output.
VO–
8
O
VO– is the negative BTL output.
GND is the ground connection.
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)§
Supply voltage, VDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 V
Input voltage, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to VDD +0.3 V
Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . internally limited (see Dissipation Rating Table)
Operating free-air temperature range, TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 40°C to 85°C
Operating junction temperature range, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 40°C to 150°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
§ Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
DISSIPATION RATING TABLE
PACKAGE
D
TA ≤ 25°C
725 mW
DERATING FACTOR
5.8 mW/°C
TA = 70°C
464 mW
TA = 85°C
377 mW
DGN
2.14 W¶
17.1 mW/°C
1.37 W
1.11 W
¶ Please see the Texas Instruments document, PowerPAD Thermally Enhanced Package Application Report
(literature number SLMA002), for more information on the PowerPAD package. The thermal data was
measured on a PCB layout based on the information in the section entitled Texas Instruments Recommended
Board for PowerPAD on page 33 of the before mentioned document.
recommended operating conditions
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Supply voltage, VDD
Operating free-air temperature, TA
2
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MIN
MAX
UNIT
2.5
5.5
V
– 40
85
°C
TPA721
700-mW MONO LOW-VOLTAGE AUDIO POWER AMPLIFIER
SLOS231C – NOVEMBER 1998 – REVISED APRIL 2001
electrical characteristics at specified free-air temperature, VDD = 3.3 V, TA = 25°C (unless otherwise
noted)
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁ
ÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
PARAMETER
TEST CONDITIONS
VOO
PSRR
Output offset voltage (measured differentially)
See Note 1
Power supply rejection ratio
IDD
IDD(SD)
Supply current
VDD = 3.2 V to 3.4 V
BTL mode
MIN
TYP
MAX
mV
1.25
2.5
mA
7
50
µA
85
Supply current, shutdown mode (see Figure 4)
UNIT
20
dB
NOTE 1: At 3 V < VDD < 5 V the dc output voltage is approximately VDD/2.
operating characteristics, VDD = 3.3 V, TA = 25°C, RL = 8 Ω
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
250
UNIT
PO
THD + N
Output power, see Note 2
THD = 0.5%,
See Figure 9
Total harmonic distortion plus noise
f = 200 Hz to 4 kHz, See Figure 7
BOM
B1
Maximum output power bandwidth
PO = 250 mW,
Gain = 2,
Unity-gain bandwidth
Open Loop,
See Figure 15
kSVR
Supply ripple rejection ratio
f = 1 kHz,
CB = 1 µF,
See Figure 2
79
dB
Vn
Noise output voltage
Gain = 1,
CB = 0.1 µF,
See Figure 19
17
µV(rms)
THD = 2%,
mW
0.55%
See Figure 7
20
kHz
1.4
MHz
NOTE 2: Output power is measured at the output terminals of the device at f = 1 kHz.
electrical characteristics at specified free-air temperature, VDD = 5 V, TA = 25°C (unless otherwise
noted)
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
PARAMETER
TEST CONDITIONS
VOO
PSRR
Output offset voltage (measured differentially)
IDD
IDD(SD)
Supply current
Power supply rejection ratio
MIN
VDD = 4.9 V to 5.1 V
TYP
MAX
mV
1.25
2.5
mA
50
100
µA
78
Supply current, shutdown mode (see Figure 4)
UNIT
20
dB
operating characteristics, VDD = 5 V, TA = 25°C, RL = 8 Ω
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
PARAMETER
TEST CONDITIONS
MIN
PO
THD + N
Output power
THD = 0.5%,
See Figure 13
Total harmonic distortion plus noise
Maximum output power bandwidth
PO = 250 mW,
Gain = 2,
f = 200 Hz to 4 kHz, See Figure 11
BOM
B1
Unity-gain bandwidth
Open Loop,
See Figure 16
THD = 2%,
See Figure 11
TYP
700†
MAX
UNIT
mW
0.5%
20
kHz
1.4
MHz
Supply ripple rejection ratio
f = 1 kHz,
CB = 1 µF,
See Figure 2
80
dB
Vn
Noise output voltage
Gain = 1,
CB = 0.1 µF,
See Figure 20
17
µV(rms)
† The DGN package, properly mounted, can conduct 700 mW RMS power continuously. The D package can only conduct 350 mW RMS power
continuously with peaks to 700 mW.
kSVR
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
TPA721
700-mW MONO LOW-VOLTAGE AUDIO POWER AMPLIFIER
SLOS231C – NOVEMBER 1998 – REVISED APRIL 2001
PARAMETER MEASUREMENT INFORMATION
VDD 6
RF
VDD/2
Audio
Input
RI
CI
VDD
CS
4
IN –
3
IN+
2
BYPASS
VO+ 5
–
+
RL = 8 Ω
CB
–
VO– 8
+
7
GND
1
SHUTDOWN
Bias
Control
Figure 1. BTL Mode Test Circuit
TYPICAL CHARACTERISTICS
Table of Graphs
FIGURE
kSVR
Supply ripple rejection ratio
vs Frequency
IDD
Supply current
vs Supply voltage
3, 4
vs Supply voltage
5
PO
THD + N
Vn
PD
4
Output power
vs Load resistance
Total harmonic distortion plus noise
vs Frequency
vs Output power
2
6
7, 8, 11, 12
9, 10, 13, 14
Open loop gain and phase
vs Frequency
15, 16
Closed loop gain and phase
vs Frequency
17, 18
Output noise voltage
vs Frequency
19, 20
Power dissipation
vs Output power
21, 22
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TPA721
700-mW MONO LOW-VOLTAGE AUDIO POWER AMPLIFIER
SLOS231C – NOVEMBER 1998 – REVISED APRIL 2001
TYPICAL CHARACTERISTICS
SUPPLY RIPPLE REJECTION RATIO
vs
FREQUENCY
SUPPLY CURRENT
vs
SUPPLY VOLTAGE
1.8
RL = 8 Ω
CB = 1 µF
BTL
–20
BTL
1.6
I DD – Supply Current – mA
–10
–30
–40
–50
–60
–70
VDD = 3.3 V
–80
–100
20
100
1.4
1.2
1
0.8
VDD = 5 V
–90
1k
10k
0.6
2.5
20k
3.5
3
f – Frequency – Hz
4
4.5
5
5.5
VDD – Supply Voltage – V
Figure 2
Figure 3
SUPPLY CURRENT
vs
SUPPLY VOLTAGE
90
SHUTDOWN = High
80
70
I DD – Supply Current – µ A
k SVR –Supply Ripple Rejection Ratio – dB
0
60
50
40
30
20
10
0
2.5
3
3.5
4
4.5
5
5.5
VDD – Supply Voltage – V
Figure 4
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
TPA721
700-mW MONO LOW-VOLTAGE AUDIO POWER AMPLIFIER
SLOS231C – NOVEMBER 1998 – REVISED APRIL 2001
TYPICAL CHARACTERISTICS
OUTPUT POWER
vs
SUPPLY VOLTAGE
1000
THD+N 1%
f = 1 kHz
BTL
PO – Output Power – mW
800
600
RL = 8 Ω
RL = 32 Ω
400
200
0
2.5
3
3.5
4
4.5
5
5.5
VDD – Supply Voltage – V
Figure 5
OUTPUT POWER
vs
LOAD RESISTANCE
800
THD+N = 1%
f = 1 kHz
BTL
PO – Output Power – mW
700
600
VDD = 5 V
500
400
300
VDD = 3.3 V
200
100
0
8
16
24
32
40
48
56
RL – Load Resistance – Ω
Figure 6
6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
64
TPA721
700-mW MONO LOW-VOLTAGE AUDIO POWER AMPLIFIER
SLOS231C – NOVEMBER 1998 – REVISED APRIL 2001
TYPICAL CHARACTERISTICS
TOTAL HARMONIC DISTORTION PLUS NOISE
vs
FREQUENCY
TOTAL HARMONIC DISTORTION PLUS NOISE
vs
FREQUENCY
10
THD+N –Total Harmonic Distortion + Noise – %
THD+N –Total Harmonic Distortion + Noise – %
10
VDD = 3.3 V
PO = 250 mW
RL = 8 Ω
BTL
AV = –20 V/V
1
AV = –10 V/V
AV = –2 V/V
0.1
0.01
20
100
1k
10k
VDD = 3.3 V
RL = 8 Ω
AV = –2 V/V
BTL
PO = 50 mW
1
0.1
PO = 125 mW
PO = 250 mW
0.01
20
20k
100
1k
f – Frequency – Hz
Figure 7
TOTAL HARMONIC DISTORTION PLUS NOISE
vs
OUTPUT POWER
10
VDD = 3.3 V
f = 1 kHz
AV = –2 V/V
BTL
THD+N –Total Harmonic Distortion + Noise – %
THD+N –Total Harmonic Distortion + Noise – %
10
1
RL = 8 Ω
0.1
0.01
0.05
0.1
20k
Figure 8
TOTAL HARMONIC DISTORTION PLUS NOISE
vs
OUTPUT POWER
0
10k
f – Frequency – Hz
0.15
0.2
0.25
0.3
0.35
0.4
f = 20 kHz
1
f = 10 kHz
f = 1 kHz
0.1
f = 20 Hz
0.01
0.01
PO – Output Power – W
VDD = 3.3 V
RL = 8 Ω
CB = 1 µF
AV = –2 V/V
BTL
0.1
1
PO – Output Power – W
Figure 9
Figure 10
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
7
TPA721
700-mW MONO LOW-VOLTAGE AUDIO POWER AMPLIFIER
SLOS231C – NOVEMBER 1998 – REVISED APRIL 2001
TYPICAL CHARACTERISTICS
TOTAL HARMONIC DISTORTION PLUS NOISE
vs
FREQUENCY
TOTAL HARMONIC DISTORTION PLUS NOISE
vs
FREQUENCY
10
VDD = 5 V
PO = 700 mW
RL = 8 Ω
BTL
THD+N –Total Harmonic Distortion + Noise – %
THD+N –Total Harmonic Distortion + Noise – %
10
AV = –20 V/V
1
AV = –10 V/V
AV =– 2 V/V
0.1
0.01
20
100
1k
10k
20k
VDD = 5 V
RL = 8 Ω
AV = –2 V/V
BTL
1
PO = 700 mW
0.1
PO = 350 mW
0.01
20
100
f – Frequency – Hz
20k
TOTAL HARMONIC DISTORTION PLUS NOISE
vs
OUTPUT POWER
10
10
THD+N –Total Harmonic Distortion + Noise – %
THD+N –Total Harmonic Distortion + Noise – %
10k
Figure 12
TOTAL HARMONIC DISTORTION PLUS NOISE
vs
OUTPUT POWER
VDD = 5 V
f = 1 kHz
AV = –2 V/V
BTL
1
RL = 8 Ω
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
f = 20 kHz
1
f = 10 kHz
f = 1 kHz
f = 20 Hz
0.1
0.01
0.01
VDD = 5 V
RL = 8 Ω
CB = 1 µF
AV = –2 V/V
BTL
PO – Output Power – W
0.1
PO – Output Power – W
Figure 13
8
1k
f – Frequency – Hz
Figure 11
0.01
0.1
PO = 50 mW
Figure 14
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
TPA721
700-mW MONO LOW-VOLTAGE AUDIO POWER AMPLIFIER
SLOS231C – NOVEMBER 1998 – REVISED APRIL 2001
TYPICAL CHARACTERISTICS
OPEN-LOOP GAIN AND PHASE
vs
FREQUENCY
80
180°
VDD = 3.3 V
RL = Open
BTL
70
140°
Phase
100°
50
60°
40
20°
30
Gain
20
– 20°
10
Phase
Open-Loop Gain – dB
60
–60°
0
–100°
–10
–140°
–20
–30
1
101
102
103
104
–180°
f – Frequency – kHz
Figure 15
OPEN-LOOP GAIN AND PHASE
vs
FREQUENCY
80
180°
VDD = 5 V
RL = Open
BTL
70
60
140°
100°
60°
40
20°
30
Gain
20
– 20°
10
Phase
Open-Loop Gain – dB
Phase
50
–60°
0
–100°
–10
–140°
–20
–30
1
101
102
f – Frequency – kHz
103
104
–180°
Figure 16
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
9
TPA721
700-mW MONO LOW-VOLTAGE AUDIO POWER AMPLIFIER
SLOS231C – NOVEMBER 1998 – REVISED APRIL 2001
TYPICAL CHARACTERISTICS
CLOSED-LOOP GAIN AND PHASE
vs
FREQUENCY
1
180°
Phase
0.75
170°
0.25
0
160°
Gain
–0.25
150°
–0.5
–0.75
140°
–1
–1.25
–1.5
–1.75
–2
101
Phase
Closed-Loop Gain – dB
0.5
VDD = 3.3 V
RL = 8 Ω
PO = 250 mW
BTL
102
130°
103
104
105
106
120°
f – Frequency – Hz
Figure 17
CLOSED-LOOP GAIN AND PHASE
vs
FREQUENCY
1
180°
Phase
0.75
170°
0.25
0
160°
Gain
–0.25
150°
–0.5
–0.75
140°
–1
–1.25
–1.5
–1.75
–2
101
VDD = 5 V
RL = 8 Ω
PO = 700 mW
BTL
102
130°
103
104
105
f – Frequency – Hz
Figure 18
10
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
120°
106
Phase
Closed-Loop Gain – dB
0.5
TPA721
700-mW MONO LOW-VOLTAGE AUDIO POWER AMPLIFIER
SLOS231C – NOVEMBER 1998 – REVISED APRIL 2001
TYPICAL CHARACTERISTICS
OUTPUT NOISE VOLTAGE
vs
FREQUENCY
100
VDD = 3.3 V
BW = 22 Hz to 22 kHz
RL = 8 Ω or 32 Ω
AV = –1 V/V
Vn – Output Noise Voltage – µV
Vn – Output Noise Voltage – µV
100
OUTPUT NOISE VOLTAGE
vs
FREQUENCY
VO BTL
Vo+
10
1
20
100
1k
10k
VDD = 5 V
BW = 22 Hz to 22 kHz
RL = 8 Ω or 32 Ω
AV = –1 V/V
VO BTL
Vo+
10
1
20
20k
100
f – Frequency – Hz
Figure 19
800
BTL Mode
VDD = 3.3 V
RL = 8 Ω
BTL Mode
VDD = 5 V
700
PD – Power Dissipation – mW
PD – Power Dissipation – mW
20k
POWER DISSIPATION
vs
OUTPUT POWER
350
250
200
150
100
10k
Figure 20
POWER DISSIPATION
vs
OUTPUT POWER
300
1k
f – Frequency – Hz
RL = 32 Ω
50
RL = 8 Ω
600
500
400
300
200
RL = 32 Ω
100
0
0
200
400
600
0
0
PD – Output Power – mW
200
400
600
800
1000
PD – Output Power – mW
Figure 21
Figure 22
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
11
TPA721
700-mW MONO LOW-VOLTAGE AUDIO POWER AMPLIFIER
SLOS231C – NOVEMBER 1998 – REVISED APRIL 2001
APPLICATION INFORMATION
bridged-tied load
Figure 23 shows a linear audio power amplifier (APA) in a BTL configuration. The TPA721 BTL amplifier consists
of two linear amplifiers driving both ends of the load. There are several potential benefits to this differential drive
configuration but initially consider power to the load. The differential drive to the speaker means that as one side
is slewing up, the other side is slewing down, and vice versa. This in effect doubles the voltage swing on the
load as compared to a ground referenced load. Plugging 2 × VO(PP) into the power equation, where voltage is
squared, yields 4× the output power from the same supply rail and load impedance (see equation 1).
V
+
(rms)
Power
V
+
O(PP)
Ǹ
2 2
V
(1)
2
(rms)
R
L
VDD
VO(PP)
RL
2x VO(PP)
VDD
–VO(PP)
Figure 23. Bridge-Tied Load Configuration
In a typical portable handheld equipment sound channel operating at 3.3 V, bridging raises the power into an
8-Ω speaker from a singled-ended (SE, ground reference) limit of 62.5 mW to 250 mW. In sound power that is
a 6-dB improvement — which is loudness that can be heard. In addition to increased power, there are frequency
response concerns. Consider the single-supply SE configuration shown in Figure 24. A coupling capacitor is
required to block the dc offset voltage from reaching the load. These capacitors can be quite large
(approximately 33 µF to 1000 µF) so they tend to be expensive, heavy, occupy valuable PCB area, and have
the additional drawback of limiting low-frequency performance of the system. This frequency-limiting effect is
due to the high pass filter network created with the speaker impedance and the coupling capacitance and is
calculated with equation 2.
f
12
(corner)
+ 2 p R1 C
(2)
L C
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TPA721
700-mW MONO LOW-VOLTAGE AUDIO POWER AMPLIFIER
SLOS231C – NOVEMBER 1998 – REVISED APRIL 2001
APPLICATION INFORMATION
bridged-tied load (continued)
For example, a 68-µF capacitor with an 8-Ω speaker would attenuate low frequencies below 293 Hz. The BTL
configuration cancels the dc offsets, which eliminates the need for the blocking capacitors. Low-frequency
performance is then limited only by the input network and speaker response. Cost and PCB space are also
minimized by eliminating the bulky coupling capacitor.
VDD
–3 dB
VO(PP)
CC
RL
VO(PP)
fc
Figure 24. Single-Ended Configuration and Frequency Response
Increasing power to the load does carry a penalty of increased internal power dissipation. The increased
dissipation is understandable considering that the BTL configuration produces 4× the output power of a SE
configuration. Internal dissipation versus output power is discussed further in the thermal considerations
section.
BTL amplifier efficiency
Linear amplifiers are notoriously inefficient. The primary cause of these inefficiencies is voltage drop across the
output stage transistors. There are two components of the internal voltage drop. One is the headroom or dc
voltage drop that varies inversely to output power. The second component is due to the sinewave nature of the
output. The total voltage drop can be calculated by subtracting the RMS value of the output voltage from VDD.
The internal voltage drop multiplied by the RMS value of the supply current, IDDrms, determines the internal
power dissipation of the amplifier.
An easy-to-use equation to calculate efficiency starts out being equal to the ratio of power from the power supply
to the power delivered to the load. To accurately calculate the RMS values of power in the load and in the
amplifier, the current and voltage waveform shapes must first be understood (see Figure 25).
IDD
VO
IDD(RMS)
V(LRMS)
Figure 25. Voltage and Current Waveforms for BTL Amplifiers
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
13
TPA721
700-mW MONO LOW-VOLTAGE AUDIO POWER AMPLIFIER
SLOS231C – NOVEMBER 1998 – REVISED APRIL 2001
APPLICATION INFORMATION
BTL amplifier efficiency (continued)
Although the voltages and currents for SE and BTL are sinusoidal in the load, currents from the supply are very
different between SE and BTL configurations. In an SE application the current waveform is a half-wave rectified
shape whereas in BTL it is a full-wave rectified waveform. This means RMS conversion factors are different.
Keep in mind that for most of the waveform both the push and pull transistors are not on at the same time, which
supports the fact that each amplifier in the BTL device only draws current from the supply for half the waveform.
The following equations are the basis for calculating amplifier efficiency.
+ P PL
Efficiency
(3)
SUP
Where:
P
L
V Lrms
+
V rms 2
L
R
L
2
+ 2R
Vp
L
+ VǸ2P
+ VDD IDDrms + VDDp R2VP
L
2V P
I DDrms +
pR
P SUP
L
Efficiency of a BTL configuration
p VP
+ 4V
DD
+
ǒ
p 2 P LR L
Ǔń
1 2
(4)
4V DD
Table 1 employs equation 4 to calculate efficiencies for three different output power levels. The efficiency of the
amplifier is quite low for lower power levels and rises sharply as power to the load is increased, resulting in a
nearly flat internal power dissipation over the normal operating range. The internal dissipation at full output
power is less than in the half power range. Calculating the efficiency for a specific system is the key to proper
power supply design.
Table 1. Efficiency vs Output Power in 3.3-V 8-Ω BTL Systems
OUTPUT POWER
(W)
EFFICIENCY
(%)
PEAK VOLTAGE
(V)
INTERNAL
DISSIPATION
(W)
0.125
33.6
1.41
0.26
0.25
47.6
0.29
0.375
58.3
2.00
2.45†
0.28
† High-peak voltage values cause the THD to increase.
A final point to remember about linear amplifiers (either SE or BTL) is how to manipulate the terms in the
efficiency equation to utmost advantage when possible. In equation 4, VDD is in the denominator. This indicates
that as VDD goes down, efficiency goes up.
14
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TPA721
700-mW MONO LOW-VOLTAGE AUDIO POWER AMPLIFIER
SLOS231C – NOVEMBER 1998 – REVISED APRIL 2001
APPLICATION INFORMATION
application schematic
Figure 26 is a schematic diagram of a typical handheld audio application circuit, configured for a gain of
–10 V/V.
VDD 6
RF
50 kΩ
Audio
Input
RI
10 kΩ
CI
VDD/2
4
IN –
3
IN+
2
BYPASS
VDD
CS
1 µF
–
VO+ 5
+
CB
2.2 µF
–
VO– 8
+
700 mW
7
GND
From System Control
SHUTDOWN
1
Bias
Control
Figure 26. TPA721 Application Circuit
The following sections discuss the selection of the components used in Figure 26.
component selection
gain setting resistors, RF and RI
ǒǓ
The gain for each audio input of the TPA721 is set by resistors RF and RI according to equation 5 for BTL mode.
BTL gain
+ *2
R
F
R
I
(5)
BTL mode operation brings about the factor 2 in the gain equation due to the inverting amplifier mirroring the
voltage swing across the load. Given that the TPA721 is a MOS amplifier, the input impedance is very high;
consequently input leakage currents are not generally a concern, although noise in the circuit increases as the
value of RF increases. In addition, a certain range of RF values is required for proper startup operation of the
amplifier. Taken together it is recommended that the effective impedance seen by the inverting node of the
amplifier be set between 5 kΩ and 20 kΩ. The effective impedance is calculated in equation 6.
Effective impedance
+ RRF)RRI
F
(6)
I
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
15
TPA721
700-mW MONO LOW-VOLTAGE AUDIO POWER AMPLIFIER
SLOS231C – NOVEMBER 1998 – REVISED APRIL 2001
APPLICATION INFORMATION
gain setting resistors, RF and RI (continued)
As an example consider an input resistance of 10 kΩ and a feedback resistor of 50 kΩ. The BTL gain of the
amplifier would be –10 V/V and the effective impedance at the inverting terminal would be 8.3 kΩ, which is well
within the recommended range.
For high performance applications, metal film resistors are recommended because they tend to have lower
noise levels than carbon resistors. For values of RF above 50 kΩ, the amplifier tends to become unstable due
to a pole formed from RF and the inherent input capacitance of the MOS input structure. For this reason, a small
compensation capacitor of approximately 5 pF should be placed in parallel with RF when RF is greater than
50 kΩ. This, in effect, creates a low pass filter network with the cutoff frequency defined in equation 7.
–3 dB
f
co(lowpass)
+ 2 p R1 C
F F
(7)
fc
For example, if RF is 100 kΩ and CF is 5 pF, then fco is 318 kHz, which is well outside of the audio range.
input capacitor, CI
In the typical application an input capacitor, CI, is required to allow the amplifier to bias the input signal to the
proper dc level for optimum operation. In this case, CI and RI form a high-pass filter with the corner frequency
determined in equation 8.
–3 dB
f
co(highpass)
+ 2 p R1 C
I I
(8)
fc
The value of CI is important to consider as it directly affects the bass (low frequency) performance of the circuit.
Consider the example where RI is 10 kΩ and the specification calls for a flat bass response down to 40 Hz.
Equation 8 is reconfigured as equation 9.
C
16
I
+ 2 p R1 fco
(9)
I
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TPA721
700-mW MONO LOW-VOLTAGE AUDIO POWER AMPLIFIER
SLOS231C – NOVEMBER 1998 – REVISED APRIL 2001
APPLICATION INFORMATION
input capacitor, CI (continued)
In this example, CI is 0.40 µF, so one would likely choose a value in the range of 0.47 µF to 1 µF. A further
consideration for this capacitor is the leakage path from the input source through the input network (RI, CI) and
the feedback resistor (RF) to the load. This leakage current creates a dc offset voltage at the input to the amplifier
that reduces useful headroom, especially in high gain applications. For this reason a low-leakage tantalum or
ceramic capacitor is the best choice. When polarized capacitors are used, the positive side of the capacitor
should face the amplifier input in most applications as the dc level there is held at VDD/2, which is likely higher
than the source dc level. It is important to confirm the capacitor polarity in the application.
power supply decoupling, CS
The TPA721 is a high-performance CMOS audio amplifier that requires adequate power supply decoupling to
ensure the output total harmonic distortion (THD) is as low as possible. Power supply decoupling also prevents
oscillations for long lead lengths between the amplifier and the speaker. The optimum decoupling is achieved
by using two capacitors of different types that target different types of noise on the power supply leads. For
higher frequency transients, spikes, or digital hash on the line, a good low equivalent-series-resistance (ESR)
ceramic capacitor, typically 0.1 µF placed as close as possible to the device VDD lead, works best. For filtering
lower-frequency noise signals, a larger aluminum electrolytic capacitor of 10 µF or greater placed near the audio
power amplifier is recommended.
midrail bypass capacitor, CB
The midrail bypass capacitor, CB, is the most critical capacitor and serves several important functions. During
startup or recovery from shutdown mode, CB determines the rate at which the amplifier starts up. The second
function is to reduce noise produced by the power supply caused by coupling into the output drive signal. This
noise is from the midrail generation circuit internal to the amplifier, which appears as degraded PSRR and
THD + N. The capacitor is fed from a 250-kΩ source inside the amplifier. To keep the start-up pop as low as
possible, the relationship shown in equation 10 should be maintained. This insures the input capacitor is fully
charged before the bypass capacitor is fully charged and the amplifier starts up.
ǒ
10
C
B
250 kΩ
Ǔ ǒ
v
1
R
F
Ǔ
) RI
C
(10)
I
As an example, consider a circuit where CB is 2.2 µF, CI is 0.47 µF, RF is 50 kΩ, and RI is 10 kΩ. Inserting these
values into the equation 10 we get:
18.2
v 35.5
which satisfies the rule. Bypass capacitor, CB, values of 0.1 µF to 2.2 µF ceramic or tantalum low-ESR capacitors
are recommended for the best THD and noise performance.
using low-ESR capacitors
Low-ESR capacitors are recommended throughout this applications section. A real (as opposed to ideal)
capacitor can be modeled simply as a resistor in series with an ideal capacitor. The voltage drop across this
resistor minimizes the beneficial effects of the capacitor in the circuit. The lower the equivalent value of this
resistance, the more the real capacitor behaves like an ideal capacitor.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
17
TPA721
700-mW MONO LOW-VOLTAGE AUDIO POWER AMPLIFIER
SLOS231C – NOVEMBER 1998 – REVISED APRIL 2001
APPLICATION INFORMATION
5-V versus 3.3-V operation
The TPA721 operates over a supply range of 2.5 V to 5.5 V. This data sheet provides full specifications for 5-V
and 3.3-V operation, as these are considered to be the two most common standard voltages. There are no
special considerations for 3.3-V versus 5-V operation with respect to supply bypassing, gain setting, or stability.
The most important consideration is that of output power. Each amplifier in TPA721 can produce a maximum
voltage swing of VDD – 1 V. This means, for 3.3-V operation, clipping starts to occur when VO(PP) = 2.3 V as
opposed to VO(PP) = 4 V at 5 V. The reduced voltage swing subsequently reduces maximum output power into
an 8-Ω load before distortion becomes significant.
Operation from 3.3-V supplies, as can be shown from the efficiency formula in equation 4, consumes
approximately two-thirds the supply power than operation from 5-V supplies for a given output-power level.
headroom and thermal considerations
Linear power amplifiers dissipate a significant amount of heat in the package under normal operating conditions.
A typical music CD requires 12 dB to 15 dB of dynamic headroom to pass the loudest portions without distortion
as compared with the average power output. From the TPA721 data sheet, one can see that when the TPA721
is operating from a 5-V supply into a 8-Ω speaker that 700 mW peaks are available. Converting watts to dB:
P
dB
+ 10 Log PW + 10Log 700 mW + –1.5 dB
Subtracting the headroom restriction to obtain the average listening level without distortion yields:
–1.5 dB – 15 dB = –16.5 (15 dB headroom)
–1.5 dB – 12 dB = –13.5 (12 dB headroom)
–1.5 dB – 9 dB = –10.5 (9 dB headroom)
–1.5 dB – 6 dB = –7.5 (6 dB headroom)
–1.5 dB – 3 dB = –4.5 (3 dB headroom)
Converting dB back into watts:
P
18
W
+ 10PdBń10
+ 22 mW (15 dB headroom)
+ 44 mW (12 dB headroom)
+ 88 mW (9 dB headroom)
+ 175 mW (6 dB headroom)
+ 350 mW (3 dB headroom)
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TPA721
700-mW MONO LOW-VOLTAGE AUDIO POWER AMPLIFIER
SLOS231C – NOVEMBER 1998 – REVISED APRIL 2001
APPLICATION INFORMATION
headroom and thermal considerations (continued)
This is valuable information to consider when attempting to estimate the heat dissipation requirements for the
amplifier system. Comparing the absolute worst case, which is 700 mW of continuous power output with 0 dB
of headroom, against 12 dB and 15 dB applications drastically affects maximum ambient temperature ratings
for the system. Using the power dissipation curves for a 5-V, 8-Ω system, the internal dissipation in the TPA721
and maximum ambient temperatures is shown in Table 2.
Table 2. TPA721 Power Rating, 5-V, 8-Ω, BTL
PEAK OUTPUT
POWER
(mW)
D PACKAGE
(SOIC)
DGN PACKAGE
(MSOP)
MAXIMUM AMBIENT
TEMPERATURE
(0 CFM)
MAXIMUM AMBIENT
TEMPERATURE
(0 CFM)
110°C
AVERAGE OUTPUT
POWER
POWER
DISSIPATION
(mW)
700
700 mW
675
34°C
700
350 mW (3 dB)
595
47°C
115°C
700
176 mW (6 dB)
475
68°C
122°C
700
88 mW (9 dB)
350
89°C
125°C
700
44 mW (12 dB)
225
111°C
125°C
Table 2 shows that the TPA721 can be used to its full 700-mW rating without any heat sinking in still air up to
110°C and 34°C for the DGN package (MSOP) and D package (SOIC) respectively.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
19
TPA721
700-mW MONO LOW-VOLTAGE AUDIO POWER AMPLIFIER
SLOS231C – NOVEMBER 1998 – REVISED APRIL 2001
MECHANICAL DATA
D (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
14 PINS SHOWN
0.050 (1,27)
0.020 (0,51)
0.014 (0,35)
14
0.010 (0,25) M
8
0.008 (0,20) NOM
0.244 (6,20)
0.228 (5,80)
0.157 (4,00)
0.150 (3,81)
Gage Plane
0.010 (0,25)
1
7
0°– 8°
A
0.044 (1,12)
0.016 (0,40)
Seating Plane
0.069 (1,75) MAX
0.010 (0,25)
0.004 (0,10)
PINS **
0.004 (0,10)
8
14
16
A MAX
0.197
(5,00)
0.344
(8,75)
0.394
(10,00)
A MIN
0.189
(4,80)
0.337
(8,55)
0.386
(9,80)
DIM
4040047 / D 10/96
NOTES: A.
B.
C.
D.
20
All linear dimensions are in inches (millimeters).
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion, not to exceed 0.006 (0,15).
Falls within JEDEC MS-012
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TPA721
700-mW MONO LOW-VOLTAGE AUDIO POWER AMPLIFIER
SLOS231C – NOVEMBER 1998 – REVISED APRIL 2001
MECHANICAL DATA
DGN (S-PDSO-G8)
PowerPAD PLASTIC SMALL-OUTLINE PACKAGE
0,38
0,25
0,65
8
0,25 M
5
Thermal Pad
(See Note D)
0,15 NOM
3,05
2,95
4,98
4,78
Gage Plane
0,25
1
0°– 6°
4
3,05
2,95
0,69
0,41
Seating Plane
1,07 MAX
0,15
0,05
0,10
4073271/A 04/98
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions include mold flash or protrusions.
The package thermal performance may be enhanced by attaching an external heat sink to the thermal pad.
This pad is electrically and thermally connected to the backside of the die and possibly selected leads.
E. Falls within JEDEC MO-187
PowerPAD is a trademark of Texas Instruments.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
21
IMPORTANT NOTICE
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its products to the specifications applicable at the time of sale in accordance with
TI’s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary
to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except
those mandated by government requirements.
Customers are responsible for their applications using TI components.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
products or services might be or are used. TI’s publication of information regarding any third party’s products
or services does not constitute TI’s approval, license, warranty or endorsement thereof.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations and notices. Representation
or reproduction of this information with alteration voids all warranties provided for an associated TI product or
service, is an unfair and deceptive business practice, and TI is not responsible nor liable for any such use.
Resale of TI’s products or services with statements different from or beyond the parameters stated by TI for
that product or service voids all express and any implied warranties for the associated TI product or service,
is an unfair and deceptive business practice, and TI is not responsible nor liable for any such use.
Also see: Standard Terms and Conditions of Sale for Semiconductor Products. www.ti.com/sc/docs/stdterms.htm
Mailing Address:
Texas Instruments
Post Office Box 655303
Dallas, Texas 75265
Copyright  2001, Texas Instruments Incorporated