Features • Fast Read Access Time - 120 ns • Dual Voltage Range Operation • • • • • • • • – Unregulated Battery Power Supply Range, 2.7V to 3.6V or Standard 5V ± 10% Supply Range Compatible with JEDEC Standard AT27C040 Low Power CMOS Operation – 20 µA max. (less than 1 µA typical) Standby for VCC = 3.6V – 36 mW max. Active at 5 MHz for VCC = 3.6V JEDEC Standard Packages – 32-Lead PLCC – 32-Lead TSOP (8 x 20 mm) – 32-Lead VSOP (8 x 14 mm) High Reliability CMOS Technology – 2,000V ESD Protection – 200 mA Latchup Immunity Rapid™ Programming Algorithm - 100 µs/byte (typical) CMOS and TTL Compatible Inputs and Outputs – JEDEC Standard for LVTTL and LVBO Integrated Product Identification Code Commercial and Industrial Temperature Ranges 4-Megabit (512K x 8) Unregulated Battery-Voltage™ High-Speed OTP EPROM Description The AT27BV040 chip is a high performance, low power, low voltage, 4,194,304-bit one-time programmable read only memory (EPROM) organized as 512K by 8 bits. It requires only one supply in the range of 2.7 to 3.6V in normal read mode operation, making it ideal for fast, portable systems using either regulated or unregulated battery power. (continued) AT27BV040 Pin Configurations Pin Name Function A0 - A18 Addresses O0 - O7 Outputs CE Chip Enable OE Output Enable TSOP, VSOP Top View Type 1 29 28 27 26 25 24 23 22 21 14 15 16 17 18 19 20 5 6 7 8 9 10 11 12 13 O1 O2 GND O3 O4 O5 O6 A7 A6 A5 A4 A3 A2 A1 A0 O0 4 3 2 1 32 31 30 A12 A15 A16 VPP VCC A18 A17 PLCC Top View A14 A13 A8 A9 A11 OE A10 CE O7 A11 A9 A8 A13 A14 A17 A18 VCC VPP A16 A15 A12 A7 A6 A5 A4 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 OE A10 CE O7 O6 O5 O4 O3 GND O2 O1 O0 A0 A1 A2 A3 Rev. 0346D–10/98 1 Atmel’s innovative design techniques provide fast speeds that rival 5V parts while keeping the low power consumption of a 3V supply. At V C C = 2.7V, any byte can be accessed in less than 100 ns. With a typical power dissipation of only 18 mW at 5 MHz and VCC = 3V, the AT27BV040 consumes less than one fifth the power of a standard 5V EPROM. Standby mode supply current is typically less than 1 µA at 3V. The AT27BV040 simplifies system design and stretches battery lifetime even further by eliminating the need for power supply regulation. The AT27BV040 is available in industry standard JEDECapproved one-time programmable (OTP) plastic PLCC, TSOP, and VSOP packages. All devices feature two-line control (CE, OE) to give designers the flexibility to prevent bus contention. The AT27BV040 operating with VCC at 3.0V produces TTL level outputs that are compatible with standard TTL logic devices operating at VCC = 5.0V. At VCC = 2.7V, the part is compatible with JEDEC approved low voltage battery operation (LVBO) interface specifications. The device is also capable of standard 5-volt operation making it ideally suited for dual supply range systems or card products that are pluggable in both 3-volt and 5-volt hosts. Atmel’s AT27BV040 has additional features to ensure high quality and efficient production use. The Rapid™ Programming Algorithm reduces the time required to program the Block Diagram 2 AT27BV040 part and guarantees reliable programming. Programming time is typically only 100 µs/byte. The Integrated Product Identification Code electronically identifies the device and manufacturer. This feature is used by industry standard programming equipment to select the proper programming algorithms and voltages. The AT27BV040 programs exactly the same way as a standard 5V AT27C040 and uses the same programming equipment. Switching Considerations Switching between active and standby conditions via the Chip Enable pin may produce transient voltage excursions. Unless accommodated by the system design, these transients may exceed data sheet limits, resulting in device non-conformance. At a minimum, a 0.1 µF high frequency, low inherent inductance, ceramic capacitor should be utilized for each device. This capacitor should be connected between the V CC and Ground terminals of the device, as close to the device as possible. Additionally, to stabilize the supply voltage level on printed circuit boards with large EPROM arrays, a 4.7 µF bulk electrolytic capacitor should be utilized, again connected between the VCC and Ground terminals. This capacitor should be positioned as close as possible to the point where the power supply is connected to the array. AT27BV040 Absolute Maximum Ratings* *NOTICE: Temperature Under Bias .................................. -40°C to +85°C Storage Temperature ..................................... -65°C to +125°C Voltage on Any Pin with Respect to Ground .........................................-2.0V to +7.0V(1) Voltage on A9 with Respect to Ground ......................................-2.0V to +14.0V(1) Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability VPP Supply Voltage with Respect to Ground .......................................-2.0V to +14.0V(1) Note: 1. Minimum voltage is -0.6V dc which may undershoot to -2.0V for pulses of less than 20 ns. Maximum output pin voltage is VCC + 0.75V dc which may be exceeded if certain precautions are observed (consult application notes) and which may overshoot to +7.0V for pulses of less than 20 ns. Operating Modes Mode \ Pin Read CE (2) VIL Output Disable (2) Standby(2) Rapid Program (3) (3) PGM Verify OE VIL Ai VPP Ai (1) X VCC DOUT (2) High Z High Z VIH X X VCC VIH X X X VCC(2) VIL X VIH VIL Ai Ai VPP VPP PGM Inhibit VIH VIH X VPP Product Identification(3)(5) VIL VIL A9 = VH(4) A0 = VIH or VIL A1 - A18 = VIL X Outputs (2) X (3) Notes: VCC VCC (3) DIN VCC (3) DOUT VCC (3) High Z VCC(3) Identification Code 1. X can be VIL or VIH. 2. Read, output disable, and standby modes require, 2.7V ≤ VCC ≤ 3.6V, or 4.5V ≤ VCC ≤ 5.5V. 3. Refer to Programming Characteristics. Programming modes require VCC = 6.5V. 4. VH = 12.0 ± 0.5V. 5. Two identifier bytes may be selected. All Ai inputs are held low (VIL), except A9 which is set to VH and A0 which is toggled low (VIL) to select the Manufacturer’s Identification byte and high (VIH) to select the Device Code byte. 3 DC and AC Operating Conditions for Read Operation AT27BV040-12 AT27BV040-15 0°C - 70°C 0°C - 70°C -40°C - 85°C -40°C - 85°C 2.7V to 3.6V 2.7V to 3.6V 5V ± 10% 5V ± 10% Com. Operating Temperature (Case) Ind. VCC Power Supply DC and Operating Characteristics for Read Operation Symbol Parameter Condition Min Max Units VCC = 2.7V to 3.6V ILI Input Load Current VIN = 0V to VCC ±1 µA ILO Output Leakage Current VOUT = 0V to VCC ±5 µA VPP = VCC 10 µA ISB1 (CMOS), CE = VCC ± 0.3V 20 µA ISB2 (TTL), CE = 2.0 to VCC + 0.5V 100 µA f = 5 MHz, IOUT = 0 mA, CE = VIL, VCC = 3.6V 10 mA IPP1(2) VPP ISB VCC(1) Standby Current ICC VCC Active Current VIL Input Low Voltage VIH Input High Voltage VOL VOH (1) Read/Standby Current Output Low Voltage Output High Voltage VCC = 3.0 to 3.6V -0.6 0.8 V VCC = 2.7 to 3.6V -0.6 0.2 x VCC V VCC = 3.0 to 3.6V 2.0 VCC + 0.5 V VCC = 2.7 to 3.6V 0.7 x VCC VCC + 0.5 V IOL = 2.0 mA 0.4 V IOL = 100 µA 0.2 V IOL = 20 µA 0.1 V IOH = -2.0 mA 2.4 V IOH = -100 µA VCC - 0.2 V IOH = -20 µA VCC - 0.1 V VCC = 4.5V to 5.5V ILI Input Load Current VIN = 0V to VCC ±1 µA ILO Output Leakage Current VOUT = 0V to VCC ±5 µA VPP = VCC 10 µA ISB1 (CMOS), CE = VCC ± 0.3V 100 µA ISB2 (TTL), CE = 2.0 to VCC + 0.5V 1 mA f = 5 MHz, IOUT = 0 mA, CE = VIL 30 mA IPP1(2) VPP ISB VCC(1) Standby Current ICC VCC Active Current VIL Input Low Voltage -0.6 0.8 V VIH Input High Voltage 2.0 VCC + 0.5 V VOL Output Low Voltage IOL = 2.1 mA 0.4 V VOH Output High Voltage IOH = -400 µA Notes: (1) Read/Standby Current 2.4 V 1. VCC must be applied simultaneously with or before VPP, and removed simultaneously with or after VPP. 2. VPP may be connected directly to VCC, except during programming. The supply current would then be the sum of ICC and IPP. 4 AT27BV040 AT27BV040 AC Characteristics for Read Operation VCC = 2.7V to 3.6V and 4.5V to 5.5V AT27BV040-12 Symbol Parameter Condition Address to Output Delay CE = OE = VIL tCE(2) CE to Output Delay tOE(2)(3) OE to Output Delay tDF(4)(5) OE or CE High to Output Float, whichever occurred first tOH Output Hold from Address, CE or OE, whichever occurred first tACC (3) Min Max Units 120 150 ns OE = VIL 120 150 ns CE = VIL 50 60 ns 40 50 ns 0 Max AT27BV040-15 Min 0 ns AC Waveforms for Read Operation(1) Notes: 1. Timing measurement references are 0.8V and 2.0V. Input AC drive levels are 0.45V and 2.4V, unless otherwise specified. 2. OE may be delayed up to tCE - tOE after the falling edge of CE without impact on tCE. 3. OE may be delayed up to tACC - tOE after the address is valid without impact on tACC. 4. This parameter is only sampled and is not 100% tested. 5. Output float is defined as the point when data is no longer driven. 5 Input Test Waveforms and Measurement Levels Output Test Load tR, tF < 20 ns (10% to 90%) Note: CL = 100 pF including jig capacitance. Pin Capacitance f = 1 MHz, T = 25°C(1) Symbol Typ Max Units Conditions CIN 4 8 pF VIN = 0V COUT 8 12 pF VOUT = 0V Note: 6 1. Typical values for nominal supply voltage. This parameter is only sampled and is not 100% tested. AT27BV040 AT27BV040 Programming Waveforms(1) Notes: 1. The Input Timing Reference is 0.8V for VIL and 2.0V for VIH. 2. tOE and tDFP are characteristics of the device but must be accommodated by the programmer. 3. When programming the AT27BV040 a 0.1 µF capacitor is required across VPP and ground to suppress spurious voltage transients. DC Programming Characteristics TA = 25 ± 5°C, VCC = 6.5 ± 0.25V, VPP = 13.0 ± 0.25V Limits Symbol Parameter Test Conditions ILI Input Load Current VIN = VIL, VIH VIL Input Low Level VIH Input High Level VOL Output Low Voltage IOL = 2.1 mA VOH Output High Voltage IOH = -400 µA ICC2 VCC Supply Current (Program and Verify) IPP2 VPP Supply Current VID A9 Product Identification Voltage Min Max Units ±10 µA -0.6 0.8 V 2.0 VCC + 0.7 V 0.4 V 2.4 CE = VIL 11.5 V 40 mA 20 mA 12.5 V 7 AC Programming Characteristics TA = 25 ± 5°C, VCC = 6.5 ± 0.25V, VPP = 13.0 ± 0.25V Limits Symbol Parameter tAS Address Setup Time tOES OE Setup Time tDS Data Setup Time tAH Address Hold Time (1) Test Conditions Input Rise and Fall Times: (10% to 90%) 20 ns Input Pulse Levels: tDH Data Hold Time tDFP OE High to Output Float Delay(2) tVPS VPP Setup Time tVCS VCC Setup Time 0.45V to 2.4V (3) CE Program Pulse Width tOE Data Valid from OE(2) tPRT VPP Pulse Rise Time During Programming Max µs 2 µs 2 µs 0 µs 2 µs 130 ns 2 µs 2 µs 95 Output Timing Reference Level: 0.8V to 2.0V Units 2 0 Input Timing Reference Level: 0.8V to 2.0V tPW Notes: Min 105 µs 150 ns 50 ns 1. VCC must be applied simultaneously or before VPP and removed simultaneously or after VPP. 2. This parameter is only sampled and is not 100% tested. Output Float is defined as the point where data is no longer driven— see timing diagram. 3. Program Pulse width tolerance is 100 µsec ± 5%. Atmel’s 27BV040 Integrated Product Identification Code(1) Pins Codes Manufacturer A0 O7 O6 O5 O4 O3 O2 O1 O0 Hex Data 0 0 0 0 1 1 1 1 0 1E Device Type 1 0 0 0 0 1 0 1 1 Note: 1. The AT27BV040 has the same Product Identification Code as the AT27C040. Both are programming compatible. 8 AT27BV040 0B AT27BV040 Rapid Programming Algorithm A 100 µs CE pulse width is used to program. The address is set to the first location. VCC is raised to 6.5V and VPP is raised to 13.0V. Each address is first programmed with one 100 µs CE pulse without verification. Then a verification/reprogramming loop is executed for each address. In the event a byte fails to pass verification, up to 10 successive 100 µs pulses are applied with a verification after each pulse. If the byte fails to verify after 10 pulses have been applied, the part is considered failed. After the byte verifies properly, the next address is selected until all have been checked. VPP is then lowered to 5.0V and VCC to 5.0V. All bytes are read again and compared with the original data to determine if the device passes or fails. 9 Ordering Information ICC (mA) VCC = 3.6V tACC (ns) Active Standby 120 8 150 Ordering Code Package 0.02 AT27BV040-12JC AT27BV040-12TC AT27BV040-12VC 32J 32T 32V Commercial (0°C to 70°C) 8 0.02 AT27BV040-12JI AT27BV040-12TI AT27BV040-12VI 32J 32T 32V Industrial (-40°C to 85°C) 8 0.02 AT27BV040-15JC AT27BV040-15TC AT27BV040-15VC 32J 32T 32V Commercial (0°C to 70°C) 8 0.02 AT27BV040-15JI AT27BV040-15TI AT27BV040-15VI 32J 32T 32V Industrial (-40°C to 85°C) Package Type 32J 32-Lead, Plastic J-Leaded Chip Carrier (PLCC) 32T 32-Lead, Plastic Thin Small Outline Package (TSOP) (8 x 20 mm) 32V 32-Lead, Plastic Thin Small Outline Package (TSOP) (8 x 14 mm) 10 AT27BV040 Operation Range AT27BV040 Packaging Information 32J, 32-Lead, Plastic J-Leaded Chip Carrier (PLCC) Dimensions in Inches and (Millimeters) JEDEC STANDARD MS-016 AE .045(1.14) X 45˚ PIN NO. 1 IDENTIFY .025(.635) X 30˚ - 45˚ .012(.305) .008(.203) .553(14.0) .547(13.9) .595(15.1) .585(14.9) .032(.813) .026(.660) .050(1.27) TYP .300(7.62) REF .430(10.9) .390(9.90) AT CONTACT POINTS 32T, 32-Lead, Plastic Thin Small Outline Package (TSOP) Dimensions in Millimeters and (Inches)* INDEX MARK .530(13.5) .490(12.4) 18.5(.728) 18.3(.720) 20.2(.795) 19.8(.780) .021(.533) .013(.330) .030(.762) .015(.381) .095(2.41) .060(1.52) .140(3.56) .120(3.05) 0.50(.020) BSC 7.50(.295) REF 0.25(.010) 0.15(.006) 8.20(.323) 7.80(.307) 1.20(.047) MAX 0.15(.006) 0.05(.002) .022(.559) X 45˚ MAX (3X) 0 5 REF .453(11.5) .447(11.4) .495(12.6) .485(12.3) 0.20(.008) 0.10(.004) 0.70(.028) 0.50(.020) *Controlling dimension; millimeters 32V, 32-Lead, Plastic Thin Small Outline Package (VSOP) Dimensions in Inches and (Millimeters) JEDEC OUTLINE MO-142 BA INDEX MARK 12.5(.492) 12.3(.484) 0.50(.020) BSC 7.50(.295) REF 14.2(.559) 13.8(.543) 0.25(.010) 0.15(.006) 8.10(.319) 7.90(.311) 1.20(.047) MAX 0.15(.006) 0.05(.002) 0 5 REF 0.20(.008) 0.10(.004) 0.70(.028) 0.50(.020) 11 Atmel Headquarters Atmel Operations Corporate Headquarters Atmel Colorado Springs 2325 Orchard Parkway San Jose, CA 95131 TEL (408) 441-0311 FAX (408) 487-2600 Europe 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TEL (719) 576-3300 FAX (719) 540-1759 Atmel Rousset Atmel U.K., Ltd. Coliseum Business Centre Riverside Way Camberley, Surrey GU15 3YL England TEL (44) 1276-686677 FAX (44) 1276-686697 Zone Industrielle 13106 Rousset Cedex, France TEL (33) 4 42 53 60 00 FAX (33) 4 42 53 60 01 Asia Atmel Asia, Ltd. Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon, Hong Kong TEL (852) 27219778 FAX (852) 27221369 Japan Atmel Japan K.K. Tonetsu Shinkawa Bldg., 9F 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan TEL (81) 3-3523-3551 FAX (81) 3-3523-7581 Fax-on-Demand North America: 1-(800) 292-8635 International: 1-(408) 441-0732 e-mail [email protected] Web Site http://www.atmel.com BBS 1-(408) 436-4309 © Atmel Corporation 1998. Atmel Cor poration makes no warranty for the use of its products, other than those expressly contained in the Company’s standard warranty which is detailed in Atmel’s Terms and Conditions located on the Company’s website. The Company assumes no responsibility for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual proper ty of Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel’s products are not authorized for use as critical components in life suppor t devices or systems. Marks bearing ® and/or ™ are registered trademarks and trademarks of Atmel Corporation. Terms and product names in this document may be trademarks of others. Printed on recycled paper. 0346D–10/98/xM