UC1724 UC2724 UC3724 Isolated Drive Transmitter FEATURES DESCRIPTION • 500mA Output Drive, Source or Sink The UC1724 family of Isolated Drive Transmitters, along with the UC1725 Isolated Drivers, provide a unique solution to driving isolated power MOSFET gates. They are particularly suited to drive the high-side devices on a high-voltage H-bridge. The UC1724 devices transmit drive logic, and drive power, to the isolated gate circuit using a low cost pulse transformer. • 8 to 35V Operation • Transmits Logic Signal Instantly • Programmable Operating Frequency • Under-Voltage Lockout • Able To Pass DC Information Across Transformer • Up To 600kHz Operation This drive system utilizes a duty-cycle modulation technique that gives instantaneous response to the drive control transistions, and reliably passes steady-state, or DC, conditions. High frequency operation, up to 600kHz, allows the cost and size of the coupling transformer to be minimized. These devices will operate over an 8 to 35 Volt supply range. The dual high current totem pole outputs are disabled by an uder-voltage lockout circuit to prevent spurious responses during startup or low voltage conditions. These devices are available in 8 pin plastic or ceramic dual-inline packages, as well as 16 pin SOIC package. BLOCK DIAGRAM Note: Pin numbers refer to DIL-8 packages. 04/99 Powered by ICminer.com Electronic-Library Service CopyRight 2003 UDG-92037 UC1724 UC2724 UC3724 CONNECTION DIAGRAMS ABSOLUTE MAXIMUM RATINGS Supply Voltage VIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40V Source/Sink Current (Pulsed) . . . . . . . . . . . . . . . . . . . . . . . . 1A Source/Sink Current (Continuous) . . . . . . . . . . . . . . . . . . . 0.5A Ouput Voltage (Pins 4, 6). . . . . . . . . . . . . . . –0.3 to (VIN +0.3)V PHI, RT, and CT inputs (Pins 1, 7, and 8) . . . . . . . . . –0.3 to 6V Operating Junction Temperature (Note 2) . . . . . . . . . . . . 150°C Storage Temperature Range . . . . . . . . . . . . . . –65°C to 150°C Lead Temperature (Soldering, 10 Seconds) . . . . . . . . . . 300°C Note 1: All voltages are with respect to GND (Pin 2); all currents are positive into, negative out of part. Note 2: Consult Unitrode Integrated Circuit Databook for thermal limitations and considerations of package. Note 3: Pin numbers refer to DIL-8 packages. DIL-8 (Top View) J Or N Package SOIC-16 (Top View) DW Package RECOMMENDED OPERATION CONDITIONS Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +9V to +35V Sink/Source Load Current (each output) . . . . . . . . . 0 to 500mA Timing Resistor. . . . . . . . . . . . . . . . . . . . . . . . . . . 2kW to 10kW Timing Capacitor . . . . . . . . . . . . . . . . . . . . . . . . . 300pF to 3nF Operating Temperature Range (UC1724) . . . –55°C<TA<125°C Operating Temperature Range (UC3724) . . . . . . 0°C<TA<70°C Note 4: Range over which the device is functional and parameter limits are guaranteed. ORDERING INFORMATION TEMPERATURE RANGE –55°C to +125°C –25°C to +85°C UC1724J UC2724DW UC2724N UC3724DW UC3724N 0°C to +70°C PACKAGE CDIP SOIC-Wide PDIP SOIC-Wide PDIP ELECTRICAL CHARACTERISTICS: Unless otherwise stated, VCC = 20V, RT = 4.3kΩ, CT = 1000pF, no load on any output and these specifications apply for: –55oC < TA < 125oC for the UC1724, –25oC < TA < 85oC for the UC2724, and 0oC < TA < 70oC for the UC3724. TA=TJ. PARAMETER TEST CONDITIONS MIN TYP MAX UNITS Under-Voltage Lockout Start-Up Threshold VIN Rising Threshold Hysteresis 7.75 9.5 V 0.4 1.0 1.5 V 1.9 2.25 µs Retriggerable One-Shot Initial Accuracy TJ = 25°C 1.54 Temperature Stability Over Operating TJ 1.0 Voltage Stability VIN = 10 to 35V 0.2 2.9 µs 0.5 %/V Operating Frequency LLOAD = 1.4mH 100 150 200 kHz Minimum Pulse Width RT = 2k CT = 300pF 100 500 1200 ns Operating Frequency RT = 2k CT = 300pF LLOAD = 1.4mH 500 750 1100 kHz Powered by ICminer.com Electronic-Library Service CopyRight 2003 2 UC1724 UC2724 UC3724 ELECTRICAL CHARACTERISTICS: Unless otherwise stated, VCC = 20V, RT = 4.3kΩ, CT = 1000pF, no load on any output and these specifications apply for: –55oC < TA < 125oC for the UC1724, –25oC < TA < 85oC for the UC2724, and 0oC < TA < 70oC for the UC3724. TA=TJ. PARAMETER TEST CONDITIONS MIN TYP MAX UNITS Phi Input (Control Input) HIGH Input Voltage 2.0 V LOW Input Voltage HIGH Input Current LOW Input Current 0.8 VIH = +2.4V VIL = +0.4V V –220 –130 µA –600 –300 µA Delay to One-Shot 350 ns Delay to Output 250 ns 0.4 V Output Drivers Output Low Level Output High Level (Volts Below VCC) Rise/Fall Time ISINK = 50mA 0.3 ISINK = 250mA 0.5 2.1 V ISOURCE = 50 mA 1.5 2.1 V ISOURCE = 250 mA 1.7 2.5 V No load 30 90 ns CT = 1.4V 15 30 mA Total Supply Current Supply Current Additional Information Please refer to the following Unitrode application topics. [1] Application Note U-127, Unique Chip Pair Simplified Isolated High-Side Switch Drive by John A. O’Connor. [2] Design Note DN-35, IGBT Drive Using MOSFET Gate Drivers by John A. O’Conner. UDG-92038 Figure 1. Typical application UNITRODE CORPORATION 7 CONTINENTAL BLVD. • MERRIMACK, NH 03054 TEL. (603) 424-2410 FAX (603) 424-3460 Powered by ICminer.com Electronic-Library Service CopyRight 2003 3 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER’S RISK. In order to minimize risks associated with the customer’s applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI’s publication of information regarding any third party’s products or services does not constitute TI’s approval, warranty or endorsement thereof. Copyright 1999, Texas Instruments Incorporated Powered by ICminer.com Electronic-Library Service CopyRight 2003