UC1852 UC2852 UC3852 High Power-Factor Preregulator FEATURES • Low-Cost Power Factor Correction • Power Factor Greater Than 0.99 • Few External Parts Required • Controlled On-Time Boost PWM • Zero-Current Switching • Limited Peak Current • Min and Max Frequency Limits • Starting Current Less Than 1mA • High-Current FET Drive Output • Under-Voltage Lockout DESCRIPTION The UC1852 provides a low-cost solution to active power-factor correction (PFC) for systems that would otherwise draw high peak current pulses from AC power lines. This circuit implements zero-current switched boost conversion, producing sinusoidal input currents with a minimum of external components, while keeping peak current substantially below that of fully-discontinuous converters. The UC1852 provides controlled switch on-time to regulate the output bulk DC voltage, an off-time defined by the boost inductor, and a zero-current sensing circuit to reactivate the switch cycle. Even though switching frequency varies with both load and instantaneous line voltage, it can be maintained within a reasonable range to minimize noise generation. While allowing higher peak switch currents than continuous PFCs such as the UC1854, this device offers less external circuitry and smaller inductors, yet better performance and easier line-noise filtering than discontinuous current PFCs with no sacrifice in complexity or cost. The ability to obtain a power factor in excess of 0.99 makes the UC1852 an optimum choice for low-cost applications in the 50 to 500 watt power range. Protection features of these devices include under-voltage lockout, output clamping, peak-current limiting, and maximum-frequency clamping. The UC1852 family is available in 8-pin plastic and ceramic dual in-line packages, and in the 8-pin small outline IC package (SOIC). The UC1852 is specified for operation from -55°C to +125°C, the UC2852 is specified for operation from -40°C to +85°C, and the UC3852 is specified for operation from 0°C to +70°C. TYPICAL APPLICATION UDG-92001 10/94 Powered by ICminer.com Electronic-Library Service CopyRight 2003 UC1852 UC2852 UC3852 CONNECTION DIAGRAM ABSOLUTE MAXIMUM RATINGS Supply Voltage (Low-impedance Source)..........................30.0V Supply Current (High-impedance Source) ......................30.0mA OUT Current, Peak .............................................................±1.0A OUT Energy, Capacitive Load............................................ 5.0µJ Input Voltage, ISNS ............................................................±5.0V Input Voltage, VFB............................................. –0.3V to +10.0V COMP Current ...............................................................±10.0mA ISET Current..................................................................–10.0mA Power Dissipation at Ta≤25°C (Note 3) ..............................1.0W Storage Temperature ....................................... –65°C to +150°C Lead Temperature (Soldering, 10 Seconds) ................... +300°C Note 1: All voltages with respect to GND (Pin 1). Note 2: All currents are positive into the specified terminal. Note 3: Refers to DIL-8 Package. Consult Packaging Section of Unitrode Integrated Circuits databook for thermal limitations and considerations of package. DIL–8 (TOP VIEW) SOIC–8 (TOP VIEW) J or N Package D Package UDG-92002 ELECTRICAL CHARACTERISTICS Unless otherwise stated, VCC=24V, ISET=50kΩ to GND, RAMP=1nF to GND, ISNS= –0.1V, VFB connected to COMP, no load on OUT, –55°C<Ta<+125°C for the UC1852, –40°C<Ta<+85°C for the UC2852, and 0°C<Ta<+70°C for the UC3852, and Ta=Tj. PARAMETER TEST CONDITIONS MIN. TYP. MAX. UNITS 4.5 5.0 5.5 V Timer Section ISET Voltage RAMP Charge Current RAMP=2.5V 88 98 108 µA RAMP Discharge Current ISNS= –1.0V, RAMP=1.0V 12 28 50 mA RAMP Saturation Voltage ISNS= –1.0V, IRAMP=100µA RAMP Threshold - Maximum Frequency VFB=10V, COMP open RAMP Threshold - PWM Comparator 0.006 0.200 V 0.92 1.02 1.12 V 3.9 4.3 4.8 V Current Sense Comparator ISNS Restart Threshold –18 –10 –4 mV ISNS Fault Threshold –550 –450 –350 mV ISNS Input Current –100 –30 100 µA 4.6 5.0 5.3 V –5.00 –0.03 5.00 Error Amplifier Section VFB Input Voltage VFB Input Bias Current µA COMP Sink Current COMP=7.5V 10 mA COMP Source Current COMP=2.5V –300 –175 –100 µA COMP Clamp Voltage VFB=0.0V, COMP open 9.2 10.0 10.6 V OUT Saturation Voltage High VCC=13V, IOUT= –200mA, RAMP=2V 0.5 1.7 2.5 V 0.5 OUT Output OUT Saturation Voltage Low IOUT=200mA, ISNS= –1.0V OUT Saturation Voltage Low @ 10mA IOUT=10mA, ISNS= –1.0V OUT Clamp Voltage IOUT= –200mA, RAMP=2V OUT Voltage during UVLO IOUT=100mA, VCC=0V VCC=10V 1.6 2.2 V 0.05 0.40 V 10.0 12.0 14.5 V 0.5 1.0 2.2 V 0.2 0.4 1.0 mA 3.0 6.0 10.0 mA 30 33 36 V Overall Section Inactive Supply Current Active Supply Current VCC Clamp Voltage ICC=25mA VCC Turn-On Threshold 14.5 16.3 17.5 V VCC Turn-Off Threshold 10.5 11.5 13.0 V 3 5 7 V VCC Threshold Hysteresis Powered by ICminer.com Electronic-Library Service CopyRight 2003 2 UC1852 UC2852 UC3852 DETAILED BLOCK DIAGRAM UDG-92003 PIN DESCRIPTIONS accuracy, ISNS should be connected to a current sense resistor through no more than 200 ohms. COMP: COMP is the output of the error amplifier and the input of the PWM comparator. To limit PWM on-time, this pin is clamped to approximately 10V. To implement soft start, the COMP pin can be pulled low and ramped up with a PNP transistor, a capacitor, and a resistor. ISET: The dominant function is of this pin is to program RAMP charging current. RAMP charging current is approximately 5V divided by the external resistor placed from ISET to ground. Resistors in the range of 10kΩ to 50kΩ are recommended, producing currents in the range of 100µA to 500µA. OUT: The output of a high-current power driver capable of driving the gate of a power MOSFET with peak currents exceeding ±500mA. To prevent damage to the power MOSFET, the OUT pin is internally driven by a 12V supply. However, lead inductance between the OUT pin and the load can cause overshoot and ringing. External current boost transistors will increase this overshoot and ringing. If there is any significant distance between the IC and the MOSFET, external clamp diodes and/or series damping resistors may be required. OUT is actively held low when the VCC is below the UVLO threshold. A second function of ISET is as reference output. The ISET pin is normally regulated to 5V ±10%. It is critical that this pin only see the loading of the RAMP programming resistor, but a high input-impedance comparator or amplifier may be connected to this pin or to a tap on the RAMP programming resistor if required. RAMP: A controlled on-time PWM requires a timer whose time can be modulated by an external voltage. The timer current is programmed by a resistor from ISET to GND. A capacitor from RAMP to GND sets the on time in conjunction with the voltage on COMP. Recommended values for the timer capacitors are between 100pF and 1nF. The third function of the ISET pin is as a FAULT output. In the event of an over-current fault, the ISET pin is forced to approximately 9V by the fault comparator. This can be used to trip an external protection circuit which can disable the load or start a fault restart cycle. VCC: VCC is the logic and control power connection for this device. VCC current is the sum of active device supply current and the average OUT current. Knowing the maximum operating frequency and the MOSFET gate charge (Qg), average OUT current can be estimated by: ISNS: This input to the zero and over current comparators is specially built to allow operation over a ±5V dynamic range. In noisy systems or systems with very high Q inductors, it is desirable to filter the signal entering the ISNS input to prevent premature restart or fault cycles. For best IOUT = Q g × F GND: Ground for all functions is through this pin. Powered by ICminer.com Electronic-Library Service CopyRight 2003 To prevent noise problems, bypass VCC to GND with both a ceramic and an electrolytic capacitor. VFB: VFB is the error amplifier inverting input. This input serves as both the voltage sense input to the error amplifier 3 UC1852 UC2852 UC3852 TYPICAL CHARACTERISTICS Error Amplifier Gain and Phase Max Frequency vs. Rset and Ct 100 1000 80 100pF 500pF 1nF Phase 3nF 60 Gain (dB) 40 Phase (deg) 20 Maximum Frequency, 100 kHz Gain 0 10 -20 10 100 1000 Frequency, kHz 1 10000 10 100 Rset, k Ω UDG-92005 UDG-92006 Max On-Time vs. Rset and Ct OUT Rise and Fall Time 1000 200 Fall Time 150 100 Maximum On-Time µs 10nF ns 100 3nF 10 1nF Rise Time 50 300pF 100pF 1 0 1 10 100 0 Rset, kΩ 10 Load Capacitance, nF UDG-92007 Powered by ICminer.com Electronic-Library Service CopyRight 2003 5 UDG-92008 4 APPLICATION INFORMATION: A 100 Watt Power Factor Preregulator UC1852 UC2852 UC3852 UDG-92004 This circuit demonstrates a complete power factor preregulator based on the UC3852. This preregulator will supply up to 100 watts at 400VDC and exhibit power factor greater than 0.995 with less than 10% total harmonic distortion. Operating input range is 90V to 160V RMS at 50Hz to 60Hz. This design is intentionally simple, yet fully functional. The UC3852 can also be used in designs featuring soft start, over-voltage protection, wide power-line voltage operation, and fault latching. For more information on applying the UC3852, refer to Unitrode Application Note U–132. PARTS LIST C1 0.47µF/250VAC X2 Class Polyester Q1 L1 IRF830 4.5A/500V 1.5Ω Power FET 680µH (Renco RL3792 with 10 Turn 24 AWG Secondary) C2 1nF/16V Ceramic C3 68µF/35V Aluminum Electrolytic C4 180pF/16V Ceramic R1 150kΩ, 1⁄4W C5 0.1µF/16V Polyester or Ceramic R2 0.2Ω, 1⁄2W Carbon Composition C6 82µF/450V Aluminum Electrolytic R3 10Ω, 1⁄4W D1 2A/500V Bridge Rectifier (Collmer KBPC106 or Powertex MB11A02V60) R4 13.3kΩ, 1⁄4W R5 1MΩ, 1⁄4W D2 100mA/50V Switching Diode (1N4148) R6 20kΩ, 1⁄4W D3 2A/500V 250ns Recovery-Time Rectifier (Motorola MR856) R7 200kΩ, 1⁄2W IC1 UC3852N Power Factor Controller IC R8 200kΩ, 1⁄2W UNITRODE INTEGRATED CIRCUITS 7 CONTINENTAL BLVD. • MERRIMACK, NH 03054 TEL. (603) 424-2410 • FAX (603) 424-3460 Powered by ICminer.com Electronic-Library Service CopyRight 2003 5 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER’S RISK. In order to minimize risks associated with the customer’s applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI’s publication of information regarding any third party’s products or services does not constitute TI’s approval, warranty or endorsement thereof. Copyright 1999, Texas Instruments Incorporated Powered by ICminer.com Electronic-Library Service CopyRight 2003