a FEATURES 10-Bit ADC with 2 s Conversion Time Small Footprint 8-Lead microSOIC Package Specified Over a –40ⴗC to +105ⴗC Temperature Range Inherent Track-and-Hold Functionality Operating Supply Range: 2.7 V to 5.5 V Specifications at 2.7 V to 5.5 V Microcontroller-Compatible Serial Interface Optional Automatic Power-Down at End of Conversion Low Power Operation 270 W at 10 kSPS Throughput Rate 2.7 mW at 100 kSPS Throughput Rate Analog Input Range: 0 V to VREF Reference Input Range: 0 V to V DD 2.7 V to 5.5 V, 2 s, 10-Bit ADC in 8-Lead microSOIC/DIP AD7810 FUNCTIONAL BLOCK DIAGRAM VDD VREF AGND AD7810 CHARGE REDISTRIBUTION DAC SERIAL PORT DOUT SCLK CLOCK OSC VIN+ VIN– COMP VDD/3 CONTROL LOGIC CONVST APPLICATIONS Low Power, Hand-Held Portable Applications that Require Analog-to-Digital Conversion with 10-Bit Accuracy; e.g., Battery Powered Test Equipment, Battery Powered Communications Systems GENERAL DESCRIPTION PRODUCT HIGHLIGHTS The AD7810 is a high speed, low power, 10-bit A/D converter that operates from a single 2.7 V to 5.5 V supply. The part contains a 2 µs successive approximation A/D converter, with inherent track/hold functionality, a pseudo differential input and a high speed serial interface that interfaces to most microcontrollers. The AD7810 is fully specified over a temperature range of –40°C to +105°C. 1. Complete, 10-Bit ADC in 8-Lead Package The AD7810 is a 10-bit 2 µs ADC with inherent track/hold functionality and a high speed serial interface—all in an 8-lead microSOIC package. VREF may be connected to VDD to eliminate the need for an external reference. The result is a high speed, low power, space saving ADC solution. By using a technique that samples the state of the CONVST (convert start) signal at the end of a conversion, the AD7810 may be used in an automatic power-down mode. When used in this mode, the AD7810 automatically powers down at the end of a conversion and “wakes up” at the start of a new conversion. This feature significantly reduces the power consumption of the part at lower throughput rates. The AD7810 can also operate in a high speed mode where the part is not powered down between conversions. In this high speed mode of operation, the conversion time of the AD7810 is 2 µs. The maximum throughput rate is dependent on the speed of the serial interface of the microcontroller. The part is available in a small 8-lead, 0.3" wide, plastic dualin-line package (mini-DIP); in an 8-lead, small outline IC (SOIC); and in an 8-lead microSOIC package. 2. Low Power, Single Supply Operation The AD7810 operates from a single +2.7 V to +5.5 V supply and typically consumes only 9 mW of power while converting. The power dissipation can be significantly reduced at lower throughput rates by using the automatic power-down mode, e.g., at a throughput rate of 10 kSPS the power consumption is only 270 µW. 3. Automatic Power-Down The automatic power-down mode, whereby the AD7810 powers down at the end of a conversion and “wakes up” before the next conversion, means the AD7810 is ideal for battery powered applications. See Power vs. Throughput Rate section. 4. Serial Interface An easy to use, fast serial interface allows connection to most popular microprocessors with no external circuitry. REV. A Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781/329-4700 World Wide Web Site: http://www.analog.com Fax: 781/326-8703 © Analog Devices, Inc., 1998 AD7810–SPECIFICATIONS (GND = 0 V, V Parameter REF = +VDD. All specifications –40ⴗC to +105ⴗC unless otherwise noted.) Y Version Units 58 –64 –64 dB min dB max dB max –67 –67 dB typ dB typ 10 ±1 ±1 ±2 ±2 Bits LSB max LSB max LSB max LSB max 10 Bits 0 VREF ±1 15 V min V max µA max pF max Input Leakage Current Input Capacitance 1.2 VDD ±3 20 V min V max µA max pF max LOGIC INPUTS2 VINH, Input High Voltage VINL, Input Low Voltage Input Current, IIN Input Capacitance, CIN 2.0 0.4 ±1 8 V min V max µA max pF max LOGIC OUTPUTS Output High Voltage, VOH Output Low Voltage, VOL High Impedance Leakage Current High Impedance Capacitance 2.4 0.4 ± 10 15 V min V max µA max pF max CONVERSION RATE Conversion Time Track/Hold Acquisition Time1 2.3 100 µs max ns max See DC Acquisition Time Section 2.7–5.5 3.5 17.5 Volts mA max mW max For Specified Performance Sampling at 350 kSPS and Logic Inputs at VDD or 0 V. VDD = 5 V 1 5 µA max µW max VDD = 5 V; VDD = 3 V 27 270 2.7 µW max µW max mW max DYNAMIC PERFORMANCE Signal to (Noise + Distortion) Ratio1 Total Harmonic Distortion1 Peak Harmonic or Spurious Noise Intermodulation Distortion2 2nd Order Terms 3rd Order Terms DC ACCURACY Resolution Relative Accuracy1 Differential Nonlinearity (DNL)1 Offset Error1 Gain Error1 Minimum Resolution for Which No Missing Codes Are Guaranteed ANALOG INPUT Input Voltage Range Input Leakage Current2 Input Capacitance2 REFERENCE INPUTS2 VREF Input Voltage Range POWER SUPPLY VDD IDD Power Dissipation Power-Down Mode IDD Power Dissipation Automatic Power Down 1 kSPS Throughput 10 kSPS Throughput 100 kSPS Throughput Test Conditions/Comments fIN = 30 kHz, fSAMPLE = 350 kHz fa = 48 kHz, fb = 48.5 kHz Typically 10 nA, VIN = 0 V to VDD ISOURCE = 200 µA ISINK = 200 µA NOTES 1 See Terminology section. 2 Sample tested during initial release and after any redesign or process change that may affect this parameter. Specifications subject to change without notice. –2– REV. A AD7810 Timing Characteristics1, 2 (–40ⴗC to +105ⴗC, V REF = +VDD, unless otherwise noted) Parameter VDD = 5 V ⴞ 10% VDD = 3 V ⴞ 10% Units Conditions/Comments t1 t2 t3 t4 t5 3 t6 3 t7 3 t83, 4 2.3 20 25 25 5 10 5 20 10 1 2.3 20 25 25 5 10 5 20 10 1 µs (max) ns (min) ns (min) ns (min) ns (min) ns (max) ns (max) ns (max) ns (min) µs (max) Conversion Time Mode 1 Operation (High Speed Mode) CONVST Pulsewidth SCLK High Pulsewidth SCLK Low Pulsewidth CONVST Rising Edge to SCLK Rising Edge Set-Up Time SCLK Rising Edge to DOUT Data Valid Delay Data Hold Time after Rising Edge SCLK Bus Relinquish Time After Falling Edge of SCLK tPOWER UP Power-Up Time After Rising Edge of CONVST NOTES 1 Sample tested to ensure compliance. 2 See Figures 14, 15 and 16. 3 These numbers are measured with the load circuit of Figure 1. They are defined as the time required for the o/p to cross 0.8 V or 2.4 V for V DD = 5 V ± 10% and 0.4 V or 2 V for V DD = 3 V ± 10%. 4 Derived from the measured time taken by the data outputs to change 0.5 V when loaded with the circuit of Figure 1. The measured number is then extrapolated back to remove the effects of charging or discharging the 50 pF capacitor. This means that the time, t8, quoted in the Timing Characteristics is the true bus relinquish time of the part and as such is independent of external bus loading capacitances. Specifications subject to change without notice. ABSOLUTE MAXIMUM RATINGS* SOIC Package, Power Dissipation . . . . . . . . . . . . . . . 450 mW θJA Thermal Impedance . . . . . . . . . . . . . . . . . . . . 160°C/W θJC Thermal Impedance . . . . . . . . . . . . . . . . . . . . . 56°C/W Lead Temperature, Soldering Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . +215°C Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . +220°C MicroSOIC Package, Power Dissipation . . . . . . . . . . 450 mW θJA Thermal Impedance . . . . . . . . . . . . . . . . . . . . 206°C/W θJC Thermal Impedance . . . . . . . . . . . . . . . . . . . . . 44°C/W Lead Temperature, Soldering Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . +215°C Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . +220°C (TA = +25°C unless otherwise noted) VDD to GND . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +7 V Digital Input Voltage to GND (CONVST, SCLK) . . . . . . . . . . . . . . –0.3 V, VDD + 0.3 V Digital Output Voltage to GND (DOUT) . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V, VDD + 0.3 V VREF to GND . . . . . . . . . . . . . . . . . . . . . . –0.3 V, VDD + 0.3 V Analog Inputs (VIN+, VIN–) . . . . . . . . . . . . . . . . . . . . –0.3 V, VDD + 0.3 V Storage Temperature Range . . . . . . . . . . . . –65°C to +150°C Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . +150°C Plastic DIP Package, Power Dissipation . . . . . . . . . . 450 mW θJA Thermal Impedance . . . . . . . . . . . . . . . . . . . +125°C/W θJC Thermal Impedance . . . . . . . . . . . . . . . . . . . . +50°C/W Lead Temperature Soldering (10 sec) . . . . . . . . . . +260°C *Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those listed in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ORDERING GUIDE Model Linearity Error (LSB) Temperature Range AD7810YN AD7810YR AD7810YRM ± 1 LSB ± 1 LSB ± 1 LSB –40°C to +105°C –40°C to +105°C –40°C to +105°C Branding Information Package Options* C1Y N-8 SO-8 RM-8 IOL 200mA TO OUTPUT PIN +1.6V CL 50pF IOH 200mA Figure 1. Load Circuit for Digital Output Timing Specifications REV. A –3– AD7810 PIN FUNCTION DESCRIPTIONS Pin No. Mnemonic Description 1 CONVST 2 3 4 5 6 7 8 VIN+ VIN– GND VREF DOUT SCLK VDD Convert Start. Falling edge puts the track-and-hold into hold mode and initiates a conversion. A rising edge on the CONVST pin enables the serial port of the AD7810. This is useful in multipackage applications where a number of devices share the same serial bus. The state of this pin at the end of conversion also determines whether the part is powered down or not. See Operating Modes section of this data sheet. Positive input of the pseudo differential analog input. Negative input of the pseudo differential analog input. Ground reference for analog and digital circuitry. External reference is connected here. Serial data is shifted out on this pin. Serial Clock. An external serial clock is applied here. Positive Supply Voltage 2.7 V to 5.5 V. PIN CONFIGURATION DIP/SOIC CONVST 1 8 VDD AD7810 7 SCLK TOP VIEW VIN– 3 (Not to Scale) 6 DOUT VIN+ 2 5 VREF GND 4 Typical Performance Characteristics 10 –15 –35 dBs POWER – mW 1 2048 POINT FFT SAMPLING 357.142kSPS FIN = 30kHz –55 –75 0.1 0.01 0 –115 10 30 20 THROUGHPUT – kSPS 40 50 1 23 45 67 89 111 133 155 177 199 221 243 265 287 309 331 353 375 397 419 441 463 485 507 529 551 573 595 617 639 661 683 705 727 749 771 793 815 837 859 881 903 925 947 969 991 1013 –95 FREQUENCY BINS Figure 2. Power vs. Throughput Figure 3. AD7810 SNR –4– REV. A AD7810 TERMINOLOGY Signal to (Noise + Distortion) Ratio This is the measured ratio of signal to (noise + distortion) at the output of the A/D converter. The signal is the rms amplitude of the fundamental. Noise is the rms sum of all nonfundamental signals up to half the sampling frequency (fS/2), excluding dc. The ratio is dependent upon the number of quantization levels in the digitization process; the more levels, the smaller the quantization noise. The theoretical signal to (noise + distortion) ratio for an ideal N-bit converter with a sine wave input is given by: Signal to (Noise + Distortion) = (6.02N + 1.76) dB Thus for a 10-bit converter, this is 62␣ dB. Total Harmonic Distortion Total harmonic distortion (THD) is the ratio of the rms sum of harmonics to the fundamental. For the AD7810 it is defined as: THD ( dB ) = 20 log V 22 + V 32 + V 42 + V 52 V1 where V1 is the rms amplitude of the fundamental and V2, V3, V4, V5 and V62 are the rms amplitudes of the second through the sixth harmonics. Peak Harmonic or Spurious Noise Peak harmonic or spurious noise is defined as the ratio of the rms values of the next largest component in the ADC output spectrum (up to fS/2 and excluding dc) to the rms value of the fundamental. Normally, the value of this specification is determined by the largest harmonic in the spectrum, but for parts where the harmonics are buried in the noise floor, it will be a noise peak. Intermodulation Distortion With inputs consisting of sine waves at two frequencies, fa and fb, any active device with nonlinearities will create distortion products at sum and difference frequencies of mfa ± nfb where m, n = 0, 1, 2, 3, etc. Intermodulation terms are those for which neither m nor n are equal to zero. For example, the second order terms include (fa + fb) and (fa – fb), while the third order terms include (2fa + fb), (2fa – fb), (fa + 2fb) and (fa – 2fb). REV. A The AD7810 is tested using the CCIF standard where two input frequencies near the top end of the input bandwidth are used. In this case, the second and third order terms are of different significance. The second order terms are usually distanced in frequency from the original sine waves while the third order terms are usually at a frequency close to the input frequencies. As a result, the second and third order terms are specified separately. The calculation of the intermodulation distortion is as per the THD specification where it is the ratio of the rms sum of the individual distortion products to the rms amplitude of the fundamental expressed in dBs. Relative Accuracy Relative accuracy or endpoint nonlinearity is the maximum deviation from a straight line passing through the endpoints of the ADC transfer function. Differential Nonlinearity This is the difference between the measured and the ideal 1␣ LSB change between any two adjacent codes in the ADC. Offset Error This is the deviation of the first code transition (0000 . . . 000) to (0000 . . . 001) from the ideal, i.e., AGND + 1 LSB. Gain Error This is the deviation of the last code transition (1111 . . . 110) to (1111 . . . 111) from the ideal (i.e., VREF – 1 LSB) after the offset error has been adjusted out. Track/Hold Acquisition Time Track/hold acquisition time is the time required for the output of the track/hold amplifier to reach its final value, within ± 1/2 LSB, after the end of conversion (the point at which the track/hold returns to track mode). It also applies to situations where there is a step input change on the input voltage applied to the VIN+ input of the AD7810. It means that the user must wait for the duration of the track/hold acquisition time, after the end of conversion or after a step input change to VIN+, before starting another conversion to ensure that the part operates to specification. –5– AD7810 SUPPLY +2.7V TO +5.5V CIRCUIT DESCRIPTION Converter Operation The AD7810 is a successive approximation analog-to-digital converter based around a charge redistribution DAC. The ADC can convert analog input signals in the range 0 V to VDD. Figures 4 and 5 below show simplified schematics of the ADC. Figure 4 shows the ADC during its acquisition phase. SW2 is closed and SW1 is in Position A; the comparator is held in a balanced condition; and the sampling capacitor acquires the signal on VIN+. 10mF TWO WIRE SERIAL INTERFACE 0.1mF VDD 0V TO VREF INPUT VREF VIN+ SCLK AD7810 VIN– mC/mP DOUT CONVST AGND Figure 6. Typical Connection Diagram Analog Input VIN+ SAMPLING CAPACITOR A CONTROL LOGIC SW1 B VIN – ACQUISITION PHASE Figure 7 shows an equivalent circuit of the analog input structure of the AD7810. The two diodes, D1 and D2, provide ESD protection for the analog inputs. Care must be taken to ensure that the analog input signal never exceeds the supply rails by more than 200 mV. This will cause these diodes to become forward biased and start conducting current into the substrate. The maximum current these diodes can conduct without causing irreversible damage to the part is 20 mA. The capacitor C2 is typically about 4 pF and can be primarily attributed to pin capacitance. The resistor R1 is a lumped component made up of the on resistance of a multiplexer and a switch. This resistor is typically about 125 Ω. The capacitor C1 is the ADC sampling capacitor and has a capacitance of 3.5 pF. CHARGE REDISTRIBUTION DAC SW2 COMPARATOR CLOCK OSC VDD /3 Figure 4. ADC Acquisition Phase When the ADC starts a conversion (see Figure 5), SW2 will open and SW1 will move to Position B, causing the comparator to become unbalanced. The control logic and the charge redistribution DAC are used to add and subtract fixed amounts of charge from the sampling capacitor to bring the comparator back into a balanced condition. When the comparator is rebalanced, the conversion is complete. The control logic generates the ADC output code. Figure 11 shows the ADC transfer function. VIN+ VIN – CONVERSION PHASE VDD /3 VIN+ C2 4pF D2 CONVERT PHASE – SWITCH OPEN ACQUISITION PHASE – SWITCH CLOSED Figure 7. Equivalent Analog Input Circuit CONTROL LOGIC SW1 B C1 3.5pF R1 125V D1 CHARGE REDISTRIBUTION DAC SAMPLING CAPACITOR A VDD The analog input of the AD7810 is made up of a pseudo differential pair. VIN+ pseudo differential with respect to VIN–. The signal is applied to VIN+, but in the pseudo differential scheme the sampling capacitor is connected to VIN– during conversion (see Figure 8). This input scheme can be used to remove offsets that exist in a system. For example, if a system had an offset of 0.5 V, the offset could be applied to VIN– and the signal applied to VIN+. This has the effect of offsetting the input span by 0.5 V. It is only possible to offset the input span when the reference voltage (VREF) is less than VDD – VOFFSET. SW2 COMPARATOR VDD /3 CLOCK OSC Figure 5. ADC Conversion Phase TYPICAL CONNECTION DIAGRAM Figure 6 shows a typical connection diagram for the AD7810. The serial interface is implemented using two wires; the rising edge of CONVST enables the serial interface—see Serial Interface section for more details. VREF is connected to a well decoupled VDD pin to provide an analog input range of 0 V to VDD. When VDD is first connected, the AD7810 powers up in a low current mode, i.e., power-down. A rising edge on the CONVST input will cause the part to power up—see Operating Modes. If power consumption is of concern, the automatic power-down at the end of a conversion should be used to improve power performance. See Power vs. Throughput Rate section of the data sheet. CHARGE REDISTRIBUTION DAC SAMPLING CAPACITOR COMPARATOR VIN+ VIN (+) CONVERSION PHASE VOFFSET VIN – VOFFSET VDD /3 CONTROL LOGIC SW2 CLOCK OSC Figure 8. Pseudo Differential Input Scheme –6– REV. A AD7810 When using the pseudo differential input scheme, the signal on VIN– must not vary by more than a 1/2 LSB during the conversion process. If the signal on VIN– varies during conversion, the conversion result will be incorrect. For single-ended operation, VIN– is always connected to AGND. Figure 9 shows the AD7810 pseudo differential input being used to make a unipolar dc current measurement. A sense resistor is used to convert the current to a voltage and the voltage, is applied to the differential input as shown. VDD VIN+ AD7810 RSENSE VIN– RL For small values of source impedance, the settling time associated with the sampling circuit (100 ns) is, in effect, the acquisition time of the ADC. For example, with a source impedance (R2) of 10 Ω, the charge time for the sampling capacitor is approximately 4 ns. The charge time becomes significant for source impedances of 2 kΩ and greater. AC Acquisition Time In ac applications it is recommended to always buffer analog input signals. The source impedance of the drive circuitry must be kept as low as possible to minimize the acquisition time of the ADC. Large values of source impedance will cause the THD to degrade at high throughput rates. In addition, better performance can generally be achieved by using an external 1 nF capacitor on VIN+. ADC TRANSFER FUNCTION Figure 9. DC Current Measurement Scheme DC Acquisition Time The ADC starts a new acquisition phase at the end of a conversion and ends on the falling edge of the CONVST signal. At the end of a conversion there is a settling time associated with the sampling circuit. This settling time lasts approximately 100 ns. The analog signal on VIN+ is also being acquired during this settling time; therefore, the minimum acquisition time needed is approximately 100 ns. The output coding of the AD7810 is straight binary. The designed code transitions occur at successive integer LSB values (i.e., 1 LSB, 2 LSBs, etc.). The LSB size is = VREF/1024. The ideal transfer characteristic for the AD7810 is shown in Figure 11 below. 111...111 111...110 ADC CODE Figure 10 shows the equivalent charging circuit for the sampling capacitor when the ADC is in its acquisition phase. R2 represents the source impedance of a buffer amplifier or resistive network; R1 is an internal multiplexer resistance and C1 is the sampling capacitor. 111...000 011...111 1LSB = VREF/1024 000...010 R2 VIN+ R1 125V 000...001 000...000 0V 1LSB C1 3.5pF ANALOG INPUT +VREF –1LSB Figure 11. Transfer Characteristic Figure 10. Equivalent Sampling Circuit During the acquisition phase, the sampling capacitor must be charged to within a 1/2 LSB of its final value. The time it takes to charge the sampling capacitor (tCHARGE) is given by the following formula: tCHARGE = 7.6 × (R2 + 125 Ω) × 3.5 pF REV. A –7– AD7810 POWER-UP TIMES OPERATING MODES Mode 1 Operation (High Speed Sampling) The AD7810 has a 1 µs power-up time. When VDD is first connected, the AD7810 is in a low current mode of operation. In order to carry out a conversion, the AD7810 must first be powered up. The ADC is powered up by a rising edge on the CONVST pin. A conversion is initiated on the falling edge of CONVST. Figure 12 shows how to power up the AD7810 when VDD is first connected or after the AD7810 is powered down using the CONVST pin. When the AD7810 is used in this mode of operation, the part is not powered down between conversions. This mode of operation allows high throughput rates to be achieved. The timing diagram in Figure 14 shows how this optimum throughput rate is achieved by bringing the CONVST signal high before the end of the conversion. The AD7810 leaves its tracking mode and goes into hold on the falling edge of CONVST. A conversion is also initiated at this time. The conversion takes 2 µs to complete. At this point, the result of the current conversion is latched into the serial shift register, and the state of the CONVST signal checked. The CONVST signal should be high at the end of the conversion to prevent the part from powering down. Care must be taken to ensure that the CONVST pin of the AD7810 is logic low when VDD is first applied. MODE 1 (CONVST IDLES HIGH) VDD tPOWER-UP < 1ms 1ms t1 CONVST CONVST MODE 2 (CONVST IDLES LOW) VDD t2 tPOWER-UP A B SCLK 1ms CONVST DOUT Figure 12. Power-Up Times CURRENT CONVERSION RESULT Figure 14. Mode 1 Operation Timing POWER VS. THROUGHPUT RATE The serial port on the AD7810 is enabled on the rising edge of the CONVST signal (see Serial Interface section). As explained earlier, this rising edge should occur before the end of the conversion process if the part is not to be powered down. A serial read can take place at any stage after the rising edge of CONVST. If a serial read is initiated before the end of the current conversion process (i.e., at time “A”), the result of the previous conversion is shifted out on the DOUT pin. It is possible to allow the serial read to extend beyond the end of a conversion. In this case the new data will not be latched into the output shift register until the read has finished. The dynamic performance of the AD7810 typically degrades by up to 3 dBs while reading during a conversion. If the user waits until the end of the conversion process, i.e., 2 µs after falling edge of CONVST (Point “B”), before initiating a read, the current conversion result is shifted out. By operating the AD7810 in Mode 2, the average power consumption of the AD7810 decreases at lower throughput rates. Figure 13 shows how the automatic power-down is implemented using the CONVST signal to achieve the optimum power performance for the AD7810. As the throughput rate is reduced, the device remains in its power-down state longer and the average power consumption over time drops accordingly. tCONVERT tPOWER-UP 2ms 1ms POWER-DOWN CONVST tCYCLE 100ms @ 10kSPS Figure 13. Automatic Power-Down For example, if the AD7810 is operated in a continuous sampling mode with a throughput rate of 10 kSPS, the power consumption is calculated as follows. The power dissipation during normal operation is 9 mW, VDD = 3 V. If the power-up time is 1 µs and the conversion time is 2 µs, the AD7810 can be said to dissipate 9 mW for 3 µs (worst case) during each conversion cycle. If the throughput rate is 10 kSPS, the cycle time is 100 µs and the average power dissipated during each cycle is (3/100) × (9 mW) = 270 µW. Figure 2 shows a graph of Power vs. Throughput. –8– REV. A AD7810 before initiating a serial read. The serial port of the AD7810 is still functional even though the AD7810 has been powered down. NOTE: Serial read should not cross the next rising edge of CONVST. Mode 2 Operation (Automatic Power-Down) When used in this mode of operation, the part automatically powers down at the end of a conversion. This is achieved by leaving the CONVST signal low until the end of the conversion. Because it takes approximately 1 µs for the part to power up after it has been powered down, this mode of operation is intended to be used in applications where slower throughput rates are required, i.e., in the order of 100 kSPS. The timing diagram in Figure 15 shows how to operate the part in this mode. If the AD7810 is powered down, the rising edge of the CONVST pulse causes the part to power up. When the part has powered up (≈ 1 µs after the rising edge of CONVST), the CONVST signal is brought low, and a conversion is initiated on this falling edge of the CONVST signal. The conversion takes 2 µs and after this time, the conversion result is latched into the serial shift register and the part powers down. Therefore, when the part is operated in Mode 2, the effective conversion time is equal to the power-up time (1 µs) and the SAR conversion time (2 µs). Because it is possible to do a serial read from the part while it is powered down, the AD7810 is powered up only to do the conversion and is immediately powered down at the end of a conversion. This significantly improves the power consumption of the part at slower throughput rates—see Power vs. Throughput Rate section. SERIAL INTERFACE The serial interface of the AD7810 consists of three wires, a serial clock input SCLK, serial port enable CONVST and a serial data output DOUT (see Figure 16). The serial interface is designed to allow easy interfacing to most microcontrollers, e.g., PIC16C, PIC17C, QSPI and SPI, without the need for any gluing logic. When interfacing to the 8051, the SCLK must be inverted. The Microprocessor Interface section explains how to interface to some popular microcontrollers. NOTE: Although the AD7810 takes 1 µs to power up after the rising edge of CONVST, it is not necessary to leave CONVST high for 1 µs after the rising edge before bringing it low to initiate a conversion. If the CONVST signal goes low before 1 µs in time has elapsed, then the power-up time is timed out internally and a conversion is then initiated. Hence the AD7810 is guaranteed to have always powered up before a conversion is initiated— even if the CONVST pulse width is < 1 µs. If the CONVST width is > 1 µs, then a conversion is initiated on the falling edge. Figure 16 shows the timing diagram for a serial read from the AD7810. The serial interface works with both a continuous and a noncontinuous serial clock. The rising edge of the CONVST signal resets a counter, which counts the number of serial clocks to ensure the correct number of bits are shifted out of the serial shift registers. The SCLK is ignored once the correct number of bits have been shifted out. In order for another serial transfer to take place, the counter must be reset by the falling edge of the 10th SCLK. Data is clocked out from the DOUT line on the first rising SCLK edge after the rising edge of the CONVST signal and on subsequent SCLK rising edges. DOUT enters its high impedance state again on the falling edge of the 10th SCLK. In multipackage applications, the CONVST signal can be used as a chip select signal. The serial interface will not shift data out until it receives a rising edge on the CONVST pin. As in the case of Mode 1 operation, the rising edge of the CONVST pulse enables the serial port of the AD7810 (see Serial Interface section). If a serial read is initiated soon after this rising edge (Point “A”), i.e., before the end of the conversion, the result of the previous conversion is shifted out on pin DOUT. In order to read the result of the current conversion, the user must wait at least 2 µs after the falling edge of CONVST tPOWER-UP t1 1ms CONVST SCLK B A DOUT CURRENT CONVERSION RESULT Figure 15. Mode 2 Operation Timing t3 SCLK 1 2 3 4 5 6 7 8 9 10 t4 t5 CONVST t7 t6 DOUT DB9 DB8 t8 DB7 DB6 DB5 DB4 DB3 DB2 Figure 16. AD7810 Serial Interface Timing REV. A –9– DB1 DB0 AD7810 MICROPROCESSOR INTERFACING AD7810 to 8051 The serial interface on the AD7810 allows the parts to be directly connected to a range of many different microprocessors. This section explains how to interface the AD7810 with some of the more common microcontroller serial interface protocols. The AD7810 requires a clock synchronized to the serial data; therefore, the 8051 serial interface must be operated in Mode 0. In this mode serial data enters and exits through RXD, and a serial clock is output on TXD (half duplex). Figure 19 shows how the 8051 is connected to the AD7810. However, because the AD7810 shifts data out on the rising edge of the serial clock, the serial clock must be inverted. AD7810 to PIC16C6x/7x The PIC16C6x Synchronous Serial Port (SSP) is configured as an SPI Master with the Clock Polarity Bit = 0. This is done by writing to the Synchronous Serial Port Control Register (SSPCON). See PIC16/17 Microcontroller User Manual. Figure 17 shows the hardware connections needed to interface to the PIC16/PIC17. In this example I/O port RA1 is being used to pulse CONVST and enable the serial port of the AD7810. This microcontroller transfers only eight bits of data during each serial transfer operation, therefore, two consecutive read operations are needed. AD7810* 8051* SCLK TXD DOUT RXD CONVST P1.1 *ADDITIONAL PINS OMITTED FOR CLARITY Figure 19. Interfacing to the 8051 Serial Port PIC16C6x/7x* AD7810* SCLK SCK/RC3 DOUT SDO/RC5 CONVST RA1 *ADDITIONAL PINS OMITTED FOR CLARITY It is possible to implement a serial interface using the data ports on the 8051 (or any microcontroller). This would allow direct interfacing between the AD7810 and 8051 to be implemented. The technique involves “bit banging” an I/O port (e.g., P1.0) to generate a serial clock and using another I/O port (e.g., P1.1) to read in data, see Figure 20. Figure 17. Interfacing to the PIC16/PIC17 AD7810* AD7810 to MC68HC11 The Serial Peripheral Interface (SPI) on the MC68HC11 is configured for Master Mode (MSTR = 0), Clock Polarity Bit (CPOL) = 0, and the Clock Phase Bit (CPHA) = 1. The SPI is configured by writing to the SPI Control Register (SPCR)—see 68HC11 User Manual. A connection diagram is shown in Figure 18. AD7810* 8051* SCLK P1.0 DOUT P1.1 CONVST P1.2 *ADDITIONAL PINS OMITTED FOR CLARITY Figure 20. Interfacing to the 8051 Using I/O Ports MC68HC11* SCLK SCLK/PD4 DOUT MISO/PD2 CONVST PA0 *ADDITIONAL PINS OMITTED FOR CLARITY Figure 18. Interfacing to the MC68HC11 –10– REV. A AD7810 OUTLINE DIMENSIONS Dimensions shown in inches and (mm). C2980a–0–8/98 8-Lead Plastic DIP (N-8) 0.430 (10.92) 0.348 (8.84) 8 5 0.280 (7.11) 0.240 (6.10) 1 4 0.325 (8.25) 0.300 (7.62) 0.060 (1.52) 0.015 (0.38) PIN 1 0.210 (5.33) MAX 0.195 (4.95) 0.115 (2.93) 0.130 (3.30) MIN 0.160 (4.06) 0.115 (2.93) 0.022 (0.558) 0.100 0.070 (1.77) 0.014 (0.356) (2.54) 0.045 (1.15) BSC 0.015 (0.381) 0.008 (0.204) SEATING PLANE 8-Lead Small Outline Package (SO-8) 0.1968 (5.00) 0.1890 (4.80) 0.1574 (4.00) 0.1497 (3.80) 8 5 1 4 PIN 1 0.0098 (0.25) 0.0040 (0.10) SEATING PLANE 0.2440 (6.20) 0.2284 (5.80) 0.0688 (1.75) 0.0532 (1.35) 0.0500 0.0192 (0.49) (1.27) 0.0138 (0.35) BSC 0.0196 (0.50) x 45° 0.0099 (0.25) 0.0098 (0.25) 0.0075 (0.19) 8° 0° 0.0500 (1.27) 0.0160 (0.41) 8-Lead Micro Small Outline Package (RM-8) 0.122 (3.10) 0.114 (2.90) 8 5 0.199 (5.05) 0.187 (4.75) 0.122 (3.10) 0.114 (2.90) 4 PIN 1 0.0256 (0.65) BSC 0.120 (3.05) 0.112 (2.84) 0.043 (1.09) 0.037 (0.94) 0.006 (0.15) 0.002 (0.05) SEATING PLANE REV. A 0.120 (3.05) 0.112 (2.84) 0.018 (0.46) 0.008 (0.20) 0.011 (0.28) 0.003 (0.08) –11– 33° 27° 0.028 (0.71) 0.016 (0.41) PRINTED IN U.S.A. 1