AM-/AMC-134 High Performance Amplifier, 15 dB Gain 5 - 200 MHz Features • • • FP-8 +49 dBm Typical Midband Third Order Intercept +29 dBm Typical Midband 1 dB Compression 4.8 dB Typical Midband Noise Figure Description M/A-COM’s AM-134 is a coupler feedback amplifier with high intercept and compression points. The use of coupler feedback minimizes noise figure and current in a high intercept amplifier. This amplifier is packaged in a flatpack with flanges. Due to the metal flatpack the thermal rise minimized. The ground plane on the PC board should be configured to remove heat from under the package. AM-134 is ideally suited for use where a high intercept, high reliability amplifier is required. Ordering Information Part Number Package AM-134 PIN AMC-134 SMA Flatpack Connectorized C-25 Absolute Maximum Ratings 1 Parameter Absolute Maximum Max. Input Power +15 dBm Vbias +17.0 V Operating Temperature -55°C to +85°C Storage Temperature -65°C to +125°C 1. Operation of this device above any one of these parameters may cause permanent damange. Pin Configuration Pin # Function Pin # Function 1 RF OUT 6 RF IN 2 GND 1 7 GND 2 3 GND 8 RF OUT 4 GND 9 GND 5 Vbias 10 GND Specifications subject to change without notice. North America: Tel. (800) 366-2266, Fax (800) 618-8883 Asia/Pacific: Tel.+81-44-844-8296, Fax +81-44-844-8298 Europe: Tel. +44 (1344) 869 595, Fax+44 (1344) 300 020 Visit www.macom.com for additional data sheets and product information. V 3.0 High Performance Amplifier, 15 dB Gain, 5 - 200 MHz AM-/AMC-134 Electrical Specifications2 TA = -55°C to +85°C Case Temperature Parameter Test Conditions Frequency Units Min Typical Max Gain 50 MHz @ +25°C 50 MHz dB 14.0 14.6 15.2 Frequency Response — 5 - 200 MHz dB — — ±0.5 Gain Variation with Temperature — 5 - 200 MHz dB -1.0 — +0.5 1 dB Compression Output Power 5 - 200 MHz dBm +23 — — Noise Figure — 5 - 200 MHz dB — — 7.0 Reverse Transmission — 5 - 200 MHz dB — -21 -19 VSWR — 5 - 200 MHz Ratio — — 2.5:1 Output IP2 Two-tone inputs up to +10 dBm 5 - 200 MHz dBm +55 — — Output IP3 Two-tone inputs up to +10 dBm 5 - 200 MHz 5 - 70 MHz dBm dBm +37 +42 — — — — Vbias — — V 14.25 15 15.75 Ibias 1.35W Typical — mA — 90 110 2. All specifications apply when operated at +15 VDC, with 50 ohms source and load impedance. 3. Heat Sinking: Operation at case temperature above 95°C is not recommended. Heat sinking adequate to dissipate 1.35W must be provided in use. Typical Performance Gain vs. Frequency -55°C 25°C RF IN 16.0 2.00 15.0 1.75 VSWR 14.0 1.50 1.25 13.0 1.00 3 5 10 20 50 100 200 300 3 5 10 Frequency (MHz) Output Power 50 64 48 62 46 60 44 3 5 10 20 50 42 100 200 300 Frequency (MHz) Specifications subject to change without notice. North America: Tel. (800) 366-2266, Fax (800) 618-8883 Asia/Pacific: Tel.+81-44-844-8296, Fax +81-44-844-8298 Europe: Tel. +44 (1344) 869 595, Fax+44 (1344) 300 020 Visit www.macom.com for additional data sheets and product information. Noise Figure (dB) IP2 66 58 50 100 200 300 Noise Figue and 1 dB Compression Intercept (dBm) IP3 IP3 20 Frequency (MHz) Intermodulation Intercept Intercept (dBm)IP2 RF OUT Noise Figure 5.5 29 5.0 28 4.5 27 4.0 3 5 10 20 50 26 100 200 300 Output Power (dBm) Gain (dB) 85°C VSWR vs. Frequency Frequency (MHz) V 3.0