Ordering number:EN6165 LCD Module ALP401 Low-Temperature Polysilicon 4.0-inch TFT LCD Module Overview This 4.0-inch LCD module is a full-color active matrix module that uses low-temperature polysilicon thin-film transistors and includes built-in driver circuits for thinframe mounting. This module conforms to both NTSC and PAL formats and the RGB stripe dot arrangement adopted is optimal for use in digital video cameras and PDAs as a display. Features and Functions • High-sharpness images with no crosstalk and a high contrast ratio. • 230,400 dots in an RGB stripe arrangement for highresolution and high-quality images. • Transparency : about 6.7%. • Built-in horizontal and vertical drivers with a level shift circuit for narrow frames, thin form factors, light weight, and low power dissipation. • Support for scan reversal both horizontally and vertically. Specifications Parameter Specification Unit Effective viewing area diagonal 10.0 (4.0 inches) cm 80.16× 60.00 mm Number of dots (horizontal× vertical) 960× 240 dot Dot pitch (horizontal× vertical) 0.0835× 0.250 mm Color arrangement RGB stripe – 93.4× 70.9× 3.0 (typical) mm 44 g Effective viewing area dimensions (horizontal× vertical) External dimensions (horizontal× vertical× thickness) Weight Note1 Note 1. Excluding the FPC and mounting sections. Package Dimensions unit:mm [ALP401] 93.4 (48.5) 3(max3.3) 44.9 80.16 70.9 60 FPC (34.6) 34 0.85 36.3 35.7±0.5 Any and all SANYO products described or contained herein do not have specifications that can handle applications that require extremely high levels of reliability, such as life-support systems, aircraft’s control systems, or other applications whose failure can be reasonably expected to result in serious physical and/or material damage. Consult with your SANYO representative nearest you before using any SANYO products described or contained herein in such applications. SANYO assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges,or other parameters) listed in products specifications of any and all SANYO products described or contained herein. SANYO Electric Co.,Ltd. Semiconductor Bussiness Headquaters TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN 30199RM (KT) No.6165–1/2 ALP401 Analog I/F System Structure Analog signal processing IC LV4122W Video signal • Composite • Y/C • Y/color difference • Analog RGB R G B Video chroma signal processing Low-temperature polysilicon TFT LCD R G B R G B RGB driver (S&H) H driver PCD PCD Serial control BUS I/F V driver Xtal Display area Level shifter Precharge circuit H SYNC V SEP. Timing controller ALP401 Timing controller LC12015-92S VCO Digital I/F System Structure Digital signal processing IC LC15001 RGB driver LA73001W Low-temperature polysilicon TFT LCD R 8 G B 8 8 ( Digital RGB serial input SYNC DOTCLK HSYNC VSYNC HDEN Serial control ( ( ( Serial R G Parallel B Signal processing Bright contrast γ ( D/A (8-bit) ( R R G G B R G B H driver B RGB driver R G B PCD PCD V driver Video signal digital RGB 8 Display area Level shifter Precharge circuit BUS I/F Timing controller ALP401 Timing controller LC12015-92S Specifications of any and all SANYO products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer's products or equipment. SANYO Electric Co., Ltd. strives to supply high-quality high-reliability products. However, any and all semiconductor products fail with some probability. It is possible that these probabilistic failures could give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire, or that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO products(including technical data,services) described or contained herein are controlled under any of applicable local export control laws and regulations, such products must not be expor ted without obtaining the expor t license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written permission of SANYO Electric Co., Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only ; it is not guaranteed for volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. This catalog provides information as of March, 1999. Specifications and information herein are subject to change without notice. PS No.6164–2/2