ETC LM140H

LM340/LM78XX Series
3-Terminal Positive Regulators
General Description
Features
The LM140/LM340A/LM340/LM7800C monolithic 3-terminal
positive voltage regulators employ internal current-limiting,
thermal shutdown and safe-area compensation, making
them essentially indestructible. If adequate heat sinking is
provided, they can deliver over 1.0A output current. They are
intended as fixed voltage regulators in a wide range of
applications including local (on-card) regulation for elimination of noise and distribution problems associated with
single-point regulation. In addition to use as fixed voltage
regulators, these devices can be used with external components to obtain adjustable output voltages and currents.
Considerable effort was expended to make the entire series
of regulators easy to use and minimize the number of external components. It is not necessary to bypass the output,
although this does improve transient response. Input bypassing is needed only if the regulator is located far from the
filter capacitor of the power supply.
The 5V, 12V, and 15V regulator options are available in the
steel TO-3 power package. The LM340A/LM340/LM7800C
series is available in the TO-220 plastic power package, and
the LM340-5.0 is available in the SOT-223 package, as well
as the LM340-5.0 and LM340-12 in the surface-mount
TO-263 package.
n Complete specifications at 1A load
n Output voltage tolerances of ± 2% at Tj = 25˚C and ± 4%
over the temperature range (LM340A)
n Line regulation of 0.01% of VOUT/V of ∆VIN at 1A load
(LM340A)
n Load regulation of 0.3% of VOUT/A (LM340A)
n Internal thermal overload protection
n Internal short-circuit current limit
n Output transistor safe area protection
n P+ Product Enhancement tested
Device
LM140
Output
Voltages
Packages
5, 12, 15 TO-3 (K)
LM340A/LM340 5, 12, 15 TO-3 (K), TO-220 (T),
SOT-223 (MP), TO-263 (S)
(5V and 12V only)
LM7800C
5, 8, 12,
15
TO-220 (T)
Typical Applications
Fixed Output Regulator
Adjustable Output Regulator
00778102
00778101
*Required if the regulator is located far from the power supply filter.
VOUT = 5V + (5V/R1 + IQ) R2 5V/R1 > 3 IQ,
load regulation (Lr) ≈ [(R1 + R2)/R1] (Lr of LM340-5).
**Although no output capacitor is needed for stability, it does help transient
response. (If needed, use 0.1 µF, ceramic disc).
Comparison between SOT-223 and D-Pak (TO-252)
Packages
Current Regulator
00778103
00778138
Scale 1:1
∆IQ = 1.3 mA over line and load changes.
© 2001 National Semiconductor Corporation
DS007781
www.national.com
LM340/LM78XX Series 3-Terminal Positive Regulators
September 2001
LM340/LM78XX
Absolute Maximum Ratings
Lead Temperature (Soldering, 10 sec.)
(Note 1)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
(Note 5)
TO-3 Package (K)
300˚C
TO-220 Package (T), TO-263
Package (S)
230˚C
ESD Susceptibility (Note 3)
2 kV
DC Input Voltage
All Devices except
LM7824/LM7824C
35V
LM7824/LM7824C
40V
Internal Power Dissipation (Note 2)
Operating Conditions (Note 1)
Temperature Range (TA) (Note 2)
LM140A, LM140
Internally Limited
Maximum Junction Temperature
150˚C
Storage Temperature Range
−55˚C to +125˚C
LM340A, LM340, LM7805C,
LM7812C, LM7815C, LM7808C
−65˚C to +150˚C
0˚C to +125˚C
LM340A Electrical Characteristics
IOUT = 1A, −55˚C ≤ TJ ≤ +150˚C (LM140A), or 0˚C ≤ TJ ≤ + 125˚C (LM340A) unless otherwise specified (Note 4)
Symbol
Output Voltage
5V
12V
Input Voltage (unless otherwise noted)
10V
19V
Parameter
VO
∆VO
Output Voltage
Line Regulation
Conditions
Min Typ Max
TJ = 25˚C
4.9
11.75
Min
12 12.25 14.7
Units
Typ Max
15
15.3
V
15.6
V
4.8
VMIN ≤ VIN ≤ VMAX
(7.5 ≤ VIN ≤ 20)
(14.8 ≤ VIN ≤ 27)
(17.9 ≤ VIN ≤ 30)
10
18
22
(7.5 ≤ VIN ≤ 20)
(14.8 ≤ VIN ≤ 27)
(17.9 ≤ VIN ≤ 30)
3
4
5.2
IO = 500 mA
TJ = 25˚C
∆VIN
11.5
10
(7.5 ≤ VIN ≤ 20)
12.5
14.4
18
(14.5 ≤ VIN ≤ 27)
4
22
(17.5 ≤ VIN ≤ 30)
V
mV
V
mV
V
TJ = 25˚C
4
9
10
mV
Over Temperature
12
30
30
mV
(8 ≤ VIN ≤ 12)
(16 ≤ VIN ≤ 22)
(20 ≤ VIN ≤ 26)
10
12
∆VIN
Load Regulation
5.1
23V
Typ Max
PD ≤ 15W, 5 mA ≤ IO ≤ 1A
∆VIN
∆VO
5
Min
15V
TJ = 25˚C
5 mA ≤ IO ≤ 1.5A
250 mA ≤ IO ≤ 750
mA
Over Temperature,
25
32
12
V
35
mV
15
19
21
mV
25
60
75
mV
6
6
6
mA
5 mA ≤ IO ≤ 1A
IQ
Quiescent
Current
TJ = 25˚C
Over Temperature
6.5
6.5
6.5
mA
∆IQ
Quiescent
Current
5 mA ≤ IO ≤ 1A
0.5
0.5
0.5
mA
Change
TJ = 25˚C, IO = 1A
0.8
0.8
0.8
mA
VMIN ≤ VIN ≤ VMAX
(7.5 ≤ VIN ≤ 20)
(14.8 ≤ VIN ≤ 27)
(17.9 ≤ VIN ≤ 30)
0.8
0.8
0.8
(8 ≤ VIN ≤ 25)
(15 ≤ VIN ≤ 30)
(17.9 ≤ VIN ≤ 30)
40
75
IO = 500 mA
VMIN ≤ VIN ≤ VMAX
VN
V
mA
V
Output Noise
Voltage
TA = 25˚C, 10 Hz ≤ f ≤ 100 kHz
Ripple Rejection
TJ = 25˚C, f = 120 Hz, IO = 1A
68
or f = 120 Hz, IO = 500 mA,
68
61
VMIN ≤ VIN ≤ VMAX
(8 ≤ VIN ≤ 18)
(15 ≤ VIN ≤ 25)
Dropout Voltage
TJ = 25˚C, IO = 1A
2.0
2.0
2.0
V
Output
Resistance
f = 1 kHz
8
18
19
mΩ
80
61
72
60
90
µV
70
dB
60
dB
Over Temperature,
RO
www.national.com
2
(18.5 ≤ VIN ≤
28.5)
V
(Continued)
IOUT = 1A, −55˚C ≤ TJ ≤ +150˚C (LM140A), or 0˚C ≤ TJ ≤ + 125˚C (LM340A) unless otherwise specified (Note 4)
Symbol
Output Voltage
5V
12V
Input Voltage (unless otherwise noted)
10V
19V
Parameter
VIN
Conditions
Min Typ Max
Min
15V
23V
Typ Max
Min
Units
Typ Max
Short-Circuit
Current
TJ = 25˚C
2.1
1.5
1.2
A
Peak Output
Current
TJ = 25˚C
2.4
2.4
2.4
A
Average TC of
VO
Min, TJ = 0˚C, IO = 5 mA
−0.6
−1.5
−1.8
mV/˚C
Input Voltage
TJ = 25˚C
Required to
Maintain
7.5
14.5
17.5
V
Line Regulation
LM140 Electrical Characteristics
(Note 4)
−55˚C ≤ TJ ≤ +150˚C unless otherwise specified
Symbol
Output Voltage
5V
12V
15V
Input Voltage (unless otherwise noted)
10V
19V
23V
Parameter
VO
Output Voltage
Conditions
Min Typ Max
Min
TJ = 25˚C, 5 mA ≤ IO ≤ 1A
4.8
5.2
11.5
PD ≤ 15W, 5 mA ≤ IO ≤ 1A
4.75
5.25
11.4
VMIN ≤ VIN ≤ VMAX
∆VO
Line Regulation
5
(8 ≤ VIN ≤ 20)
IO = 500 mA TJ = 25˚C
3
∆VIN
IO ≤ 1A
4
5 mA ≤ IO ≤ 1.5A
120
(15 ≤ VIN ≤ 27)
50
(7.5 ≤ VIN ≤ 20)
∆VIN
TJ = 25˚C
(15.5 ≤ VIN ≤ 27)
120
TJ = 25˚C
15
12.6 14.25
50
15.6
V
15.75
V
(18.5 ≤ VIN ≤
30)
4
(18.5 ≤ VIN ≤
30)
120
60
75
(8 ≤ VIN ≤ 12)
(16 ≤ VIN ≤ 22)
(20 ≤ VIN ≤ 26)
250 mA ≤ IP ≤ 750
mA
12
120
V
150 mV
25
50
V
150 mV
(17.7 ≤ VIN ≤
30)
10
V
150 mV
(17.5 ≤ VIN ≤
30)
(14.6 ≤ VIN ≤ 27)
−55˚C ≤ TJ ≤ +150˚C
Load Regulation
12.5 14.4
(14.5 ≤ VIN ≤ 30)
(8 ≤ VIN ≤ 20)
∆VIN
∆VO
12
(7 ≤ VIN ≤ 25)
−55˚C ≤ TJ ≤ +150˚C
∆VIN
50
Units
Typ Max Min Typ Max
12
V
mV
V
150 mV
25
60
75
50
120
150 mV
TJ = 25˚C
6
6
6
mA
−55˚C ≤ TJ ≤ +150˚C
7
7
7
mA
−55˚C ≤ TJ ≤ +150˚C,
mV
5 mA ≤ IO ≤ 1A
IQ
∆IQ
Quiescent Current
IO ≤ 1A
Quiescent Current
5 mA ≤ IO ≤ 1A
0.5
0.5
0.5
mA
Change
TJ = 25˚C, IO ≤ 1A
0.8
0.8
0.8
mA
VMIN ≤ VIN ≤ VMAX
(8 ≤ VIN ≤ 20)
IO = 500 mA, −55˚C ≤ TJ ≤ +150˚C
VMIN ≤ VIN ≤ VMAX
VN
Output Noise
Voltage
0.8
(8 ≤ VIN ≤ 25)
TA = 25˚C, 10 Hz ≤ f ≤ 100 kHz
40
3
(15 ≤ VIN ≤ 27)
(18.5 ≤ VIN ≤
30)
0.8
(15 ≤ VIN ≤ 30)
75
0.8
V
mA
(18.5 ≤ VIN ≤
30)
V
90
µV
www.national.com
LM340/LM78XX
LM340A Electrical Characteristics
LM340/LM78XX
LM140 Electrical Characteristics
(Note 4) (Continued)
−55˚C ≤ TJ ≤ +150˚C unless otherwise specified
Symbol
Output Voltage
5V
12V
15V
Input Voltage (unless otherwise noted)
10V
19V
23V
Parameter
Conditions
Min Typ Max
Min
Units
Typ Max Min Typ Max
IO ≤ 1A, TJ = 25˚C
68
IO ≤ 500 mA,
68
61
VMIN ≤ VIN ≤ VMAX
(8 ≤ VIN ≤ 18)
(15 ≤ VIN ≤ 25)
Dropout Voltage
TJ = 25˚C, IO = 1A
2.0
2.0
2.0
V
Output Resistance
f = 1 kHz
8
18
19
mΩ
Short-Circuit
Current
TJ = 25˚C
2.1
1.5
1.2
A
Peak Output
Current
TJ = 25˚C
2.4
2.4
2.4
A
Average TC of
VOUT
0˚C ≤ TJ ≤ +150˚C, IO = 5 mA
−0.6
−1.5
−1.8
Input Voltage
TJ = 25˚C, IO ≤ 1A
Ripple Rejection
80
61
72
60
70
dB
or
f = 120 Hz
60
dB
−55˚C ≤ TJ ≤+150˚C
RO
VIN
Required to
Maintain
7.5
14.6
(18.5 ≤ VIN ≤
28.5)
V
mV/˚C
17.7
V
Line Regulation
LM340/LM7800C Electrical Characteristics (Note 4)
0˚C ≤ TJ ≤ +125˚C unless otherwise specified
Output Voltage
Symbol
Input Voltage (unless otherwise noted)
Parameter
VO
∆VO
Output Voltage
Line Regulation
Conditions
Min
5V
12V
15V
10V
19V
23V
Typ Max Min
Typ Max Min Typ
Max
12
15.6
V
TJ = 25˚C, 5 mA ≤ IO ≤ 1A
4.8
PD ≤ 15W, 5 mA ≤ IO ≤ 1A
4.75
VMIN ≤ VIN ≤ VMAX
(7.5 ≤ VIN ≤ 20)
IO = 500 mA TJ = 25˚C
5
0˚C ≤ TJ ≤ +125˚C
IO ≤ 1A
Load Regulation
TJ = 25˚C
5 mA ≤ IO ≤ 1.5A
4
120
(14.5 ≤ VIN ≤
30)
120
(15 ≤ VIN ≤ 27)
50
120
0˚C ≤ TJ ≤ +125˚C
15
12.6 14.25
(14.5 ≤ VIN ≤
27)
50
(7.5 ≤ VIN ≤ 20)
∆VIN
12.5 14.4
(8 ≤ VIN ≤ 20)
TJ = 25˚C
∆VIN
∆VO
50
(7 ≤ VIN ≤ 25)
∆VIN
11.5
5.25 11.4
3
∆VIN
5.2
(14.6 ≤ VIN ≤
27)
Units
15.75
V
(17.5 ≤ VIN ≤ 30)
V
4
mV
150
(17.5 ≤ VIN ≤ 30)
150
(18.5 ≤ VIN ≤ 30)
150
(17.7 ≤ VIN ≤ 30)
25
60
75
(8 ≤ VIN ≤ 12)
(16 ≤ VIN ≤ 22)
(20 ≤ VIN ≤ 26)
10
12
12
120
mV
V
mV
V
mV
V
150
mV
25
60
75
mV
5 mA ≤ IO ≤ 1A, 0˚C ≤ TJ ≤
+125˚C
50
120
150
mV
8
8
8
mA
250 mA ≤ IO ≤ 750 mA
50
V
IQ
Quiescent Current
IO ≤ 1A
8.5
8.5
8.5
mA
∆IQ
Quiescent Current
5 mA ≤ IO ≤ 1A
0.5
0.5
0.5
mA
Change
TJ = 25˚C, IO ≤ 1A
1.0
1.0
1.0
mA
VMIN ≤ VIN ≤ VMAX
(7.5 ≤ VIN ≤ 20)
TJ = 25˚C
0˚C ≤ TJ ≤ +125˚C
www.national.com
4
(14.8 ≤ VIN ≤
27)
(17.9 ≤ VIN ≤ 30)
V
Symbol
Output Voltage
5V
12V
15V
Input Voltage (unless otherwise noted)
10V
19V
23V
Parameter
Conditions
Min
Typ Max Min
IO ≤ 500 mA, 0˚C ≤ TJ ≤ +125˚C
VMIN ≤ VIN ≤ VMAX
VN
Output Noise
Voltage
IO ≤ 1A, TJ =
25˚C
f = 120 Hz
1.0
mA
(14.5 ≤ VIN ≤
30)
(17.5 ≤ VIN ≤ 30)
V
40
75
90
µV
70
dB
62
or IO ≤ 500 mA,
Max
1.0
(7 ≤ VIN ≤ 25)
TA = 25˚C, 10 Hz ≤ f ≤ 100 kHz
Ripple Rejection
Typ Max Min Typ
1.0
Units
80
55
72
54
62
55
54
dB
VMIN ≤ VIN ≤ VMAX
(8 ≤ VIN ≤ 18)
(15 ≤ VIN ≤ 25)
(18.5 ≤ VIN ≤
28.5)
Dropout Voltage
TJ = 25˚C, IO = 1A
2.0
2.0
2.0
V
Output Resistance
f = 1 kHz
8
18
19
mΩ
Short-Circuit Current TJ = 25˚C
2.1
1.5
1.2
A
Peak Output
Current
2.4
2.4
2.4
A
−0.6
−1.5
−1.8
0˚C ≤ TJ ≤ +125˚C
RO
TJ = 25˚C
Average TC of VOUT 0˚C ≤ TJ ≤ +125˚C, IO = 5 mA
VIN
Input Voltage
V
mV/˚C
TJ = 25˚C, IO ≤ 1A
Required to
Maintain
7.5
14.6
17.7
V
Line Regulation
Note 1: Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Conditions are conditions under which the device functions
but the specifications might not be guaranteed. For guaranteed specifications and test conditions see the Electrical Characteristics.
Note 2: The maximum allowable power dissipation at any ambient temperature is a function of the maximum junction temperature for operation (TJMAX = 125˚C
or 150˚C), the junction-to-ambient thermal resistance (θJA), and the ambient temperature (TA). PDMAX = (TJMAX − TA)/θJA. If this dissipation is exceeded, the die
temperature will rise above TJMAX and the electrical specifications do not apply. If the die temperature rises above 150˚C, the device will go into thermal shutdown.
For the TO-3 package (K, KC), the junction-to-ambient thermal resistance (θJA) is 39˚C/W. When using a heatsink, θJA is the sum of the 4˚C/W junction-to-case
thermal resistance (θJC) of the TO-3 package and the case-to-ambient thermal resistance of the heatsink. For the TO-220 package (T), θJA is 54˚C/W and θJC is
4˚C/W. If SOT-223 is used, the junction-to-ambient thermal resistance is 174˚C/W and can be reduced by a heatsink (see Applications Hints on heatsinking).
If the TO-263 package is used, the thermal resistance can be reduced by increasing the PC board copper area thermally connected to the package: Using 0.5 square
inches of copper area, θJA is 50˚C/W; with 1 square inch of copper area, θJAis 37˚C/W; and with 1.6 or more inches of copper area, θJA is 32˚C/W.
Note 3: ESD rating is based on the human body model, 100 pF discharged through 1.5 kΩ.
Note 4: All characteristics are measured with a 0.22 µF capacitor from input to ground and a 0.1 µF capacitor from output to ground. All characteristics except noise
voltage and ripple rejection ratio are measured using pulse techniques (tw ≤ 10 ms, duty cycle ≤ 5%). Output voltage changes due to changes in internal temperature
must be taken into account separately.
Note 5: A military RETS specification is available on request. At the time of printing, the military RETS specifications for the LM140AK-5.0/883, LM140AK-12/883,
and LM140AK-15/883 complied with the min and max limits for the respective versions of the LM140A. At the time of printing, the military RETS specifications for
the LM140K-5.0/883, LM140K-12/883, and LM140K-15/883 complied with the min and max limits for the respective versions of the LM140. The LM140H/883,
LM140K/883, and LM140AK/883 may also be procured as a Standard Military Drawing.
5
www.national.com
LM340/LM78XX
LM340/LM7800C Electrical Characteristics (Note 4) (Continued)
0˚C ≤ TJ ≤ +125˚C unless otherwise specified
LM340/LM78XX
LM7808C
Electrical Characteristics
0˚C ≤ TJ ≤ +150˚C, VI = 14V, IO = 500 mA, CI = 0.33 µF, CO = 0.1 µF, unless otherwise specified
Symbol
Parameter
Conditions (Note 6)
LM7808C
Min
Typ
7.7
Units
Max
VO
Output Voltage
TJ = 25˚C
8.0
8.3
V
∆VO
Line Regulation
TJ = 25˚C
10.5V ≤ VI ≤ 25V
6.0
160
mV
11.0V ≤ VI ≤ 17V
2.0
80
∆VO
Load Regulation
TJ = 25˚C
5.0 mA ≤ IO ≤ 1.5A
12
160
250 mA ≤ IO ≤ 750
mA
4.0
80
8.4
V
4.3
8.0
mA
1.0
mA
VO
Output Voltage
11.5V ≤ VI ≤ 23V, 5.0 mA ≤ IO ≤ 1.0A, P ≤ 15W
IQ
Quiescent Current
TJ = 25˚C
∆IQ
Quiescent
With Line
Current Change
With Load
VN
Noise
TA = 25˚C, 10 Hz ≤ f ≤ 100 kHz
∆VI/∆VO
Ripple Rejection
f = 120 Hz, IO = 350 mA, TJ = 25˚C
VDO
Dropout Voltage
IO = 1.0A, TJ = 25˚C
7.6
11.5V ≤ VI ≤ 25V
5.0 mA ≤ IO ≤ 1.0A
mV
0.5
56
52
µV
72
dB
2.0
V
16
mΩ
RO
Output Resistance
f = 1.0 kHz
IOS
Output Short Circuit Current
TJ = 25˚C, VI = 35V
0.45
A
IPK
Peak Output Current
TJ = 25˚C
2.2
A
∆VO/∆T
Average Temperature
IO = 5.0 mA
0.8
mV/˚C
Coefficient of Output Voltage
Note 6: All characteristics are measured with a 0.22 µF capacitor from input to ground and a 0.1 µF capacitor from output to ground. All characteristics except noise
voltage and ripple rejection ratio are measured using pulse techniques (tw ≤ 10 ms, duty cycle ≤ 5%). Output voltage changes due to changes in internal temperature
must be taken into account separately.
www.national.com
6
Maximum Average Power Dissipation
Maximum Average Power Dissipation
00778122
00778123
Maximum Power Dissipation (TO-263)
(See Note 2)
Output Voltage (Normalized to 1V at TJ = 25˚C)
00778124
00778125
Note: Shaded area refers to LM340A/LM340, LM7805C, LM7812C and
LM7815C.
Ripple Rejection
Ripple Rejection
00778126
00778127
7
www.national.com
LM340/LM78XX
Typical Performance
Characteristics
LM340/LM78XX
Typical Performance Characteristics
(Continued)
Output Impedance
Dropout Characteristics
00778129
00778128
Quiescent Current
Peak Output Current
00778131
00778130
Note: Shaded area refers to LM340A/LM340, LM7805C, LM7812C and
LM7815C.
Dropout Voltage
Quiescent Current
00778132
Note: Shaded area refers to LM340A/LM340, LM7805C, LM7812C and
LM7815C.
00778133
www.national.com
8
LM340/LM78XX
Line Regulation
140AK-5.0, IOUT = 1A, TA = 25˚C
Line Regulation
140AK-5.0, VIN = 10V, TA = 25˚C
00778106
00778105
Equivalent Schematic
00778107
tial, while the output remains near the initial VOUTbecause of
the stored charge in the large output capacitor. The capacitor
will then discharge through a large internal input to output
diode and parasitic transistors. If the energy released by the
capacitor is large enough, this diode, low current metal and
the regulator will be destroyed. The fast diode in Figure 1 will
shunt most of the capacitors discharge current around the
regulator. Generally no protection diode is required for values of output capacitance ≤ 10 µF.
Raising the Output Voltage above the Input Voltage:
Since the output of the device does not sink current, forcing
the output high can cause damage to internal low current
paths in a manner similar to that just described in the “Shorting the Regulator Input” section.
Application Hints
The LM340/LM78XX series is designed with thermal protection, output short-circuit protection and output transistor safe
area protection. However, as with any IC regulator, it becomes necessary to take precautions to assure that the
regulator is not inadvertently damaged. The following describes possible misapplications and methods to prevent
damage to the regulator.
Shorting the Regulator Input: When using large capacitors
at the output of these regulators, a protection diode connected input to output (Figure 1) may be required if the input
is shorted to ground. Without the protection diode, an input
short will cause the input to rapidly approach ground poten-
9
www.national.com
LM340/LM78XX
Application Hints
(Continued)
Regulator Floating Ground (Figure 2): When the ground
pin alone becomes disconnected, the output approaches the
unregulated input, causing possible damage to other circuits
connected to VOUT. If ground is reconnected with power
“ON”, damage may also occur to the regulator. This fault is
most likely to occur when plugging in regulators or modules
with on card regulators into powered up sockets. Power
should be turned off first, thermal limit ceases operating, or
ground should be connected first if power must be left on.
Transient Voltages: If transients exceed the maximum
rated input voltage of the device, or reach more than 0.8V
below ground and have sufficient energy, they will damage
the regulator. The solution is to use a large input capacitor, a
series input breakdown diode, a choke, a transient suppressor or a combination of these.
00778110
FIGURE 3. Transients
When a value for θ(H–A) is found using the equation shown,
a heatsink must be selected that has a value that is less than
or equal to this number.
θ(H–A) is specified numerically by the heatsink manufacturer
in this catalog, or shown in a curve that plots temperature
rise vs power dissipation for the heatsink.
HEATSINKING TO-263 AND SOT-223 PACKAGE PARTS
Both the TO-263 (“S”) and SOT-223 (“MP”) packages use a
copper plane on the PCB and the PCB itself as a heatsink.
To optimize the heat sinking ability of the plane and PCB,
solder the tab of the plane.
shows for the TO-263 the measured values of θ(J–A) for
different copper area sizes using a typical PCB with 1 ounce
copper and no solder mask over the copper area used for
heatsinking.
00778108
FIGURE 1. Input Short
00778109
FIGURE 2. Regulator Floating Ground
00778139
FIGURE 4. θ(J–A) vs Copper (1 ounce)
Area for the TO-263 Package
As shown in the figure, increasing the copper area beyond 1
square inch produces very little improvement. It should also
be observed that the minimum value of θ(J–A) for the TO-263
package mounted to a PCB is 32˚C/W.
As a design aid, Figure 5 shows the maximum allowable
power dissipation compared to ambient temperature for the
TO-263 device (assuming θ(J–A) is 35˚C/W and the maximum junction temperature is 125˚C).
www.national.com
10
LM340/LM78XX
Application Hints
(Continued)
00778141
FIGURE 6. θ(J–A) vs Copper (2 ounce) Area
for the SOT-223 Package
00778140
FIGURE 5. Maximum Power Dissipation vs
TAMB for the TO-263 Package
Figures 6, 7 show the information for the SOT-223 package.
Figure 6 assumes a θ(J–A) of 74˚C/W for 1 ounce copper and
51˚C/W for 2 ounce copper and a maximum junction temperature of 125˚C.
00778142
Please see AN-1028 for power enhancement techniques
to
be used with the SOT-223 package.
FIGURE 7. Maximum Power Dissipation vs
TAMB for the SOT-223 Package
Typical Applications
Fixed Output Regulator
00778113
Note: Bypass capacitors are recommended for optimum stability and transient response, and should be located as close as possible to the regulator.
High Input Voltage Circuits
00778114
11
www.national.com
LM340/LM78XX
Typical Applications
(Continued)
00778115
High Current Voltage Regulator
00778116
High Output Current, Short Circuit Protected
00778117
www.national.com
12
LM340/LM78XX
Typical Applications
(Continued)
Positive and Negative Regulator
00778118
Connection Diagrams and
Ordering Information
TO-220 Power Package (T)
TO-3 Metal Can Package (K)
00778112
Top View
Plastic Package Order Numbers:
LM340AT-5.0 LM340T-5.0
LM340T-12 LM340T-15
LM7805CT LM7812CT
LM7815CT LM7808CT
See Package Number T03B
00778111
Bottom View
Steel Package Order Numbers:
LM140K-5.0
LM140K-12
LM140K-15
LM340K-12
LM340K-15
LM340K-5.0
See Package Number K02A
LM140K-5.0/883 LM140K-12/883 LM140K-15/883
See Package Number K02C
TO-39 Metal Can Package (H)
00778119
Top View
Metal Can Order Numbers†:
LM140H-5.0/883
LM140H-6.0/883
LM140H-8.0/883
LM140H-12/883
LM140H-15/883
LM140H-24/883
See Package Number H03A
13
www.national.com
LM340/LM78XX
Connection Diagrams and
Ordering Information (Continued)
3-Lead SOT-223
(Front View)
Order Number LM340MP-5.0
Package Marked NO0A
See Package Number MA04A
TO-263 Surface-Mount Package (S)
00778120
00778143
Top View
00778121
Side View
Surface-Mount Package Order Numbers:
LM340S-5.0
LM340S-12
See Package Number TS3B
†The specifications for the LM140H/883 devices are not contained in this datasheet. If specifications for these devices
are required, contact the National Semiconductor Sales Office/Distributors.
www.national.com
14
LM340/LM78XX
Physical Dimensions
inches (millimeters)
unless otherwise noted
TO-3 Metal Can Package (K)
Order Number LM140K-5.0, LM340K-5.0, LM140K-12, LM340K-12,
LM140K-15, LM340K-15, LM7806CK, LM7808CK, LM7818CK or LM7824CK
NS Package Number K02A
TO-3 Metal Can Package (K)
Mil-Aero Products
Order Number LM140K-5.0/883, LM140K-12/883, or LM140K-15/883
NS Package Number K02C
15
www.national.com
LM340/LM78XX
Physical Dimensions
inches (millimeters) unless otherwise noted (Continued)
TO-263 Surface-Mount Package (S)
Order Number LM340S-5.0 or LM340S-12
NS Package Number TS3B
www.national.com
16
LM340/LM78XX
Physical Dimensions
inches (millimeters) unless otherwise noted (Continued)
TO-220 Power Package (T)
Order Number LM340AT/LM340T-5.0, LM340AT/LM340T-12, LM340AT/LM340T-15,
LM7805CT, LM7812CT, LM7815CT, LM7806CT, LM7808CT, LM7818CT or LM7824CT
NS Package Number T03B
17
www.national.com
LM340/LM78XX Series 3-Terminal Positive Regulators
Physical Dimensions
inches (millimeters) unless otherwise noted (Continued)
3-Lead SOT-223 Package
Order Part Number LM340MP-5.0
NS Package Number MA04A
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury to the user.
National Semiconductor
Corporation
Americas
Email: [email protected]
www.national.com
National Semiconductor
Europe
Fax: +49 (0) 180-530 85 86
Email: [email protected]
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.
National Semiconductor
Asia Pacific Customer
Response Group
Tel: 65-2544466
Fax: 65-2504466
Email: [email protected]
National Semiconductor
Japan Ltd.
Tel: 81-3-5639-7560
Fax: 81-3-5639-7507
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.