AD AD7195BCPZ-RL7

4.8 kHz, Ultralow Noise, 24-Bit
Sigma-Delta ADC with PGA and AC Excitation
AD7195
FEATURES
Chromatography
PLC/DCS analog input modules
Data acquisition
Medical and scientific instrumentation
AC or DC sensor excitation
RMS noise: 8.5 nV at 4.7 Hz (gain = 128)
16 noise-free bits at 2.4 kHz (gain = 128)
Up to 22.5 noise-free bits (gain = 1)
Offset drift: 5 nV/°C
Gain drift: 1 ppm/°C
Specified drift over time
2 differential/4 pseudo differential input channels
Automatic channel sequencer
Programmable gain (1 to 128)
Output data rate: 4.7 Hz to 4.8 kHz
Internal or external clock
Simultaneous 50 Hz/60 Hz rejection
Power supply
AVDD: 4.75 V to 5.25 V
DVDD: 2.7 V to 5.25 V
Current: 6 mA
Temperature range: –40°C to +105°C
Package: 32-lead LFCSP
GENERAL DESCRIPTION
The AD7195 is a low noise, complete analog front end for high
precision measurement applications. It contains a low noise,
24-bit sigma-delta (Σ-Δ) analog-to-digital converter (ADC).
The on-chip low noise gain stage means that signals of small
amplitude can be interfaced directly to the ADC. The AD7195
contains ac excitation, which is used to remove dc-induced
offsets from bridge sensors.
The device can be configured to have two differential inputs or
four pseudo differential inputs. The on-chip channel sequencer
allows several channels to be enabled, and the AD7195 sequentially
converts on each enabled channel. This simplifies communication
with the part. The on-chip 4.92 MHz clock can be used as the
clock source to the ADC or, alternatively, an external clock or
crystal can be used. The output data rate from the part can be
varied from 4.7 Hz to 4.8 kHz.
INTERFACE
The device has two digital filter options. The choice of filter
affects the rms noise/noise-free resolution at the programmed
output data rate, the settling time, and the 50 Hz/60 Hz rejection. For applications that require all conversions to be settled,
the AD7195 includes a zero latency feature.
3-wire serial
SPI, QSPI™, MICROWIRE™, and DSP compatible
Schmitt trigger on SCLK
APPLICATIONS
Weigh scales
Strain gage transducers
Pressure measurement
Temperature measurement
The part operates with a 5 V analog power supply and a digital
power supply from 2.7 V to 5.25 V. It consumes a current of
6 mA. It is housed in a 32-lead LFCSP package.
FUNCTIONAL BLOCK DIAGRAM
AVDD AGND DVDD DGND
REFIN(+) REFIN(–)
REFERENCE
DETECT
AIN1
AIN2
AIN3
AIN4
AVDD
MUX
PGA
AINCOM
SERIAL
INTERFACE
AND
CONTROL
LOGIC
Σ-Δ
ADC
DOUT/RDY
DIN
SCLK
CS
SYNC
BPDSW
AGND
AC
EXCITATION
CLOCK
AD7195
ACX1
ACX1
CLOCK
CIRCUITRY
ACX2
ACX2
MCLK1 MCLK2
08771-001
TEMP
SENSOR
Figure 1.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2010 Analog Devices, Inc. All rights reserved.
AD7195
TABLE OF CONTENTS
Features .............................................................................................. 1 Overview ..................................................................................... 25 Interface ............................................................................................. 1 Analog Input Channel ............................................................... 26 Applications ....................................................................................... 1 PGA .............................................................................................. 26 General Description ......................................................................... 1 Reference ..................................................................................... 26 Functional Block Diagram .............................................................. 1 Reference Detect ......................................................................... 26 Revision History ............................................................................... 2 Bipolar/Unipolar Configuration .............................................. 27 Specifications..................................................................................... 3 Data Output Coding .................................................................. 27 Timing Characteristics ................................................................ 6 Burnout Currents ....................................................................... 27 Absolute Maximum Ratings............................................................ 8 AC Excitation .............................................................................. 27 Thermal Resistance ...................................................................... 8 Channel Sequencer .................................................................... 28 ESD Caution .................................................................................. 8 Digital Interface .......................................................................... 28 Pin Configuration and Function Descriptions ............................. 9 Reset ............................................................................................. 32 Typical Performance Characteristics ........................................... 11 System Synchronization ............................................................ 32 RMS Noise and Resolution............................................................ 13 Clock ............................................................................................ 32 Sinc Chop Disabled ................................................................... 13 Enable Parity ............................................................................... 32 Sinc Chop Disabled ................................................................... 14 Temperature Sensor ................................................................... 32 Sinc Chop Enabled .................................................................... 15 Bridge Power-Down Switch ...................................................... 33 Sinc Chop Enabled .................................................................... 16 Calibration................................................................................... 33 On-Chip Registers .......................................................................... 17 Digital Filter ................................................................................ 34 Communications Register ......................................................... 18 Sinc4 Filter (Chop Disabled) ..................................................... 34 Status Register ............................................................................. 19 Sinc3 Filter (Chop Disabled) ..................................................... 36 Mode Register ............................................................................. 19 Chop Enabled (Sinc4 Filter) ...................................................... 38 Configuration Register .............................................................. 21 Chop Enabled (Sinc3 Filter) ...................................................... 40 Data Register ............................................................................... 23 Summary of Filter Options ....................................................... 41 ID Register ................................................................................... 23 Grounding and Layout .............................................................. 42 GPOCON Register ..................................................................... 23 Applications Information .............................................................. 43 Offset Register ............................................................................. 24 Weigh Scales ................................................................................ 43 Full-Scale Register ...................................................................... 24 Outline Dimensions ....................................................................... 44 ADC Circuit Information .............................................................. 25 Ordering Guide .......................................................................... 44 4
3
4
3
REVISION HISTORY
1/10—Revision 0: Initial Version
Rev. 0 | Page 2 of 44
AD7195
SPECIFICATIONS
AVDD = 4.75 V to 5.25 V, DVDD = 2.7 V to 5.25 V, AGND = DGND = 0 V; REFIN(+) = AVDD, REFIN(−) = AGND, MCLK = 4.92 MHz,
TA = TMIN to TMAX, unless otherwise noted.
Table 1.
Parameter
ADC
Output Data Rate
No Missing Codes 2
Min
Typ
4.7
1.17
1.56
24
24
Resolution
RMS Noise and Output
Data Rates
Integral Nonlinearity
Gain = 12
Gain > 1
Offset Error 4 , 5
±1
±5
±75/gain
±0.5
±100/gain
Offset Error Drift vs.
Temperature
Offset Error Drift vs. Time
±5
±5
25
Gain Error4
±0.001
Gain Drift vs. Temperature
Gain Drift vs. Time
±0.006
±1
10
Power Supply Rejection
98
100
Common-Mode Rejection
@ DC2
@ DC
@ 50 Hz, 60 Hz2
@ 50 Hz, 60 Hz2
Normal Mode Rejection2
Sinc4 Filter
Internal Clock
@ 50 Hz, 60 Hz
@ 50 Hz
@ 60 Hz
External Clock
@ 50 Hz, 60 Hz
@ 50 Hz
@ 60 Hz
Sinc3 Filter
Internal Clock
@ 50 Hz, 60 Hz
@ 50 Hz
@ 60 Hz
100
115
120
120
Max
Unit
Test Conditions/Comments 1
4800
1200
1600
Hz
Hz
Hz
Bits
Bits
Chop disabled
Chop enabled, sinc4 filter
Chop enabled, sinc3 filter
FS > 1, sinc4 filter 3
FS > 4, sinc3 filter3
See the RMS Noise and Resolution section
See the RMS Noise and Resolution section
±5
±15
ppm of FSR
ppm of FSR
μV
μV
nV/°C
±0.005
nV/°C
nV/°C
nV/1000
hours
% max
%
ppm/°C
ppm/1000
hours
dB
95
103
110
dB
115
140
Chop disabled
Chop enabled
Gain = 1 to 16; chop disabled
Gain = 32 to 128; chop disabled
Chop enabled
Gain > 32
AVDD = 5 V, gain = 1, TA = 25°C (factory calibration
conditions)
Gain > 1, post internal full-scale calibration
Gain = 1
Gain = 1, VIN = 1 V
Gain = 8, VIN = 1 V/gain
Gain > 8, VIN = 1 V/gain
dB min
dB min
dB
dB
Gain = 1, VIN = 1 V
Gain > 1, VIN = 1 V/gain
10 Hz output data rate, 50 ± 1 Hz, 60 ± 1 Hz
50 ± 1 Hz (50 Hz output data rate), 60 ± 1 Hz
(60 Hz output data rate)
100
74
dB
dB
96
97
dB
dB
10 Hz output data rate, 50 ± 1 Hz, 60 ± 1 Hz
50 Hz output data rate, REJ60 6 = 1, 50 ± 1 Hz, 60 ± 1
Hz
50 Hz output data rate, 50 ± 1 Hz
60 Hz output data rate, 60 ± 1 Hz
120
82
120
120
dB
dB
dB
dB
10 Hz output data rate, 50 ± 1 Hz, 60 ± 1 Hz
50 Hz output data rate, REJ606 = 1, 50 ± 1 Hz, 60 ± 1 Hz
50 Hz output data rate, 50 ± 1 Hz
60 Hz output data rate, 60 ± 1 Hz
75
60
70
70
dB
dB
dB
dB
10 Hz output data rate, 50 ± 1 Hz, 60 ± 1 Hz
50 Hz output data rate, REJ606 = 1, 50 ± 1 Hz, 60 ± 1 Hz
50 Hz output data rate, 50 ± 1 Hz
60 Hz output data rate, 60 ± 1 Hz
Rev. 0 | Page 3 of 44
AD7195
Parameter
External Clock
@ 50 Hz, 60 Hz
@ 50 Hz
@ 60 Hz
ANALOG INPUTS
Differential Input Voltage
Ranges
Min
Typ
100
67
95
95
±VREF/gain
−(AVDD −
1.25 V)/gain
Absolute AIN Voltage Limits2
Unbuffered Mode
Buffered Mode
Analog Input Current
Buffered Mode
Input Current2
Output High Voltage, VOH2
Output Low Voltage, VOL2
INTERNAL/EXTERNAL CLOCK
Internal Clock
Frequency
Duty Cycle
External Clock/Crystal2
Frequency
Input Low Voltage VINL
Input High Voltage, VINH
Input Current
dB
dB
dB
dB
10 Hz output data rate, 50 ± 1 Hz, 60 ± 1 Hz
50 Hz output data rate, REJ606 = 1, 50 ± 1 Hz, 60 ± 1 Hz
50 Hz output data rate, 50 ± 1 Hz
60 Hz output data rate, 60 ± 1 Hz
V
VREF = REFIN(+) − REFIN(−), gain = 1 to 128
V
Gain > 1
V
V
−2
−4.5
+2
+4.5
Gain = 1
Gain > 1
±5
nA
nA
pA/°C
±5
±1
±0.05
±1.6
μA/V
μA/V
nA/V/°C
nA/V/°C
Gain = 1, input current varies with input voltage
Gain > 1
External clock
Internal clock
AVDD
V
REFIN = REFIN(+) − REFIN(−). The differential input must
be limited to ±(AVDD − 1.25 V)/gain when gain > 1
AVDD + 0.05
V
1
AVDD
GND − 0.05
Normal Mode Rejection2
Common-Mode Rejection
Reference Detect Levels
TEMPERATURE SENSOR
Accuracy
Sensitivity
BRIDGE POWER-DOWN SWITCH
RON
Allowable Current2
BURNOUT CURRENTS
AIN Current
DIGITAL OUTPUTS (ACXx, ACXx )
Test Conditions/Comments 1
AVDD + 0.05
AVDD − 0.25
Input Current Drift
Absolute REFIN Voltage
Limits2
Average Reference Input
Current
Average Reference Input
Current Drift
+(AVDD −
1.25 V)/gain
Unit
AGND − 0.05
AGND + 0.25
Input Current Drift
Unbuffered Mode
Input Current
REFERENCE INPUT
REFIN Voltage
Max
7
μA/V
±0.03
nA/V/°C
External clock
±1.3
Same as for
analog inputs
95
nA/V/°C
Internal clock
0.3
dB
V
0.6
±2
2815
10
30
500
4
0.4
4.72
2.5
3.5
−10
4.9152
Applies after user calibration at 25°C
Bipolar mode
Ω
mA
Continuous current
nA
Analog inputs must be buffered and chop disabled
V
V
AVDD = 5 V, ISOURCE = 200 μA
AVDD = 5 V, ISINK = 800 μA
5.12
MHz
%
5.12
0.8
0.4
MHz
V
V
V
V
μA
50:50
2.4576
°C
Codes/°C
+10
Rev. 0 | Page 4 of 44
DVDD = 5 V
DVDD = 3 V
DVDD = 3 V
DVDD = 5 V
AD7195
Parameter
LOGIC INPUTS
Input High Voltage, VINH2
Input Low Voltage, VINL2
Hysteresis2
Input Currents
LOGIC OUTPUT (DOUT/RDY)
Output High Voltage, VOH2
Output Low Voltage, VOL2
Output High Voltage, VOH2
Output Low Voltage, VOL2
Floating-State Leakage
Current
Floating-State Output
Capacitance
Data Output Coding
SYSTEM CALIBRATION2
Full-Scale Calibration Limit
Zero-Scale Calibration Limit
Input Span
POWER REQUIREMENTS 7
Power Supply Voltage
AVDD − AGND
DVDD − DGND
Power Supply Currents
AIDD Current
DIDD Current
IDD (Power-Down Mode)
Min
Typ
Max
Unit
0.8
0.25
+10
V
V
V
μA
2
0.1
−10
DVDD − 0.6
0.4
4
0.4
+10
−10
10
V
V
V
V
μA
Test Conditions/Comments 1
DVDD = 3 V, ISOURCE = 100 μA
DVDD = 3 V, ISINK = 100 μA
DVDD = 5 V, ISOURCE = 200 μA
DVDD = 5 V, ISINK = 1.6 mA
pF
Offset binary
−1.05 × FS
0.8 × FS
1.05 × FS
2.1 × FS
V
V
V
4.75
2.7
5.25
5.25
V
V
1
1.3
4.5
5
6.4
6.9
0.4
0.6
mA
mA
mA
mA
mA
mA
mA
mA
mA
μA
0.85
1.1
3.5
4
5
5.5
0.35
0.5
1.5
2
1
gain = 1, buffer off
gain = 1, buffer on
gain = 8, buffer off
gain = 8, buffer on
gain = 16 to 128, buffer off
gain = 16 to 128, buffer on
DVDD = 3 V
DVDD = 5 V
External crystal used
Temperature range: −40°C to +105°C.
Specification is not production tested, but is supported by characterization data at initial product release.
FS is the decimal equivalent of Bit FS9 to Bit FS0 in the mode register.
4
Following a system or internal zero-scale calibration, the offset error is in the order of the noise for the programmed gain and output data rate selected. A system fullscale calibration reduces the gain error to the order of the noise for the programmed gain and output data rate.
5
The analog inputs are configured for differential mode.
6
REJ60 is a bit in the mode register. When the output data rate is set to 50 Hz, setting REJ60 to 1 places a notch at 60 Hz, allowing simultaneous 50 Hz/60 Hz rejection.
7
Digital inputs equal to DVDD or DGND.
2
3
Rev. 0 | Page 5 of 44
AD7195
TIMING CHARACTERISTICS
AVDD = 4.75 V to 5.25 V, DVDD = 2.7 V to 5.25 V, AGND = DGND = 0 V, Input Logic 0 = 0 V, Input Logic 1 = DVDD, unless
otherwise noted.
Table 2.
Parameter
READ AND WRITE OPERATIONS
t3
t4
READ OPERATION
t1
t2 3
t5 5, 6
t6
t7
WRITE OPERATION
t8
t9
t10
t11
Limit at TMIN, TMAX (B Version)
Unit
Conditions/Comments 1, 2
100
100
ns min
ns min
SCLK high pulse width
SCLK low pulse width
0
60
80
0
60
80
10
80
0
10
ns min
ns max
ns max
ns min
ns max
ns max
ns min
ns max
ns min
ns min
CS falling edge to DOUT/RDY active time
DVDD = 4.75 V to 5.25 V
DVDD = 2.7 V to 3.6 V
SCLK active edge to data valid delay 4
DVDD = 4.75 V to 5.25 V
DVDD = 2.7 V to 3.6 V
Bus relinquish time after CS inactive edge
0
30
25
0
ns min
ns min
ns min
ns min
CS falling edge to SCLK active edge setup time4
Data valid to SCLK edge setup time
Data valid to SCLK edge hold time
CS rising edge to SCLK edge hold time
1
SCLK inactive edge to CS inactive edge
SCLK inactive edge to DOUT/RDY high
Sample tested during initial release to ensure compliance. All input signals are specified with tR = tF = 5 ns (10% to 90% of DVDD) and timed from a voltage level of 1.6 V.
See Figure 3 and Figure 4.
3
These numbers are measured with the load circuit shown in Figure 2 and defined as the time required for the output to cross the VOL or VOH limits.
4
The SCLK active edge is the falling edge of SCLK.
5
These numbers are derived from the measured time taken by the data output to change 0.5 V when loaded with the circuit shown in Figure 2. The measured number
is then extrapolated back to remove the effects of charging or discharging the 50 pF capacitor. This means that the times quoted in the timing characteristics are the
true bus relinquish times of the part and, as such, are independent of external bus loading capacitances.
6 RDY
returns high after a read of the data register. In single conversion mode and continuous conversion mode, the same data can be read again, if required, while RDY
is high, although care should be taken to ensure that subsequent reads do not occur close to the next output update. If the continuous read feature is enabled, the
digital word can be read only once.
2
Rev. 0 | Page 6 of 44
AD7195
Circuit and Timing Diagram
ISINK (1.6mA WITH DVDD = 5V,
100µA WITH DVDD = 3V)
TO
OUTPUT
PIN
1.6V
ISOURCE (200µA WITH DVDD = 5V,
100µA WITH DVDD = 3V)
08771-002
50pF
Figure 2. Load Circuit for Timing Characterization
CS (I)
t6
t1
t5
MSB
DOUT/RDY (O)
LSB
t7
t2
t3
08771-003
SCLK (I)
t4
I = INPUT, O = OUTPUT
Figure 3. Read Cycle Timing Diagram
CS (I)
t11
t8
SCLK (I)
t9
t10
MSB
LSB
I = INPUT, O = OUTPUT
Figure 4. Write Cycle Timing Diagram
Rev. 0 | Page 7 of 44
08771-004
DIN (I)
AD7195
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted.
THERMAL RESISTANCE
Table 3.
θJA is specified for the worst-case conditions, that is, a device
soldered in a circuit board for surface-mount packages.
Parameter
AVDD to AGND
DVDD to AGND
AGND to DGND
Analog Input Voltage to AGND
Reference Input Voltage to AGND
Digital Input Voltage to DGND
Digital Output Voltage to DGND
AIN/Digital Input Current
Operating Temperature Range
Storage Temperature Range
Maximum Junction Temperature
Lead Temperature, Soldering
Reflow
Rating
−0.3 V to +6.5 V
−0.3 V to +6.5 V
−0.3 V to +0.3 V
−0.3 V to AVDD + 0.3 V
−0.3 V to AVDD + 0.3 V
−0.3 V to DVDD + 0.3 V
−0.3 V to DVDD + 0.3 V
10 mA
−40°C to +105°C
−65°C to +150°C
150°C
Table 4. Thermal Resistance
Package Type
32-Lead LFCSP_WQ
ESD CAUTION
260°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Rev. 0 | Page 8 of 44
θJA
32.5
θJC
32.71
Unit
°C/W
AD7195
32
31
30
29
28
27
26
25
CS
SCLK
MCLK2
MCLK1
DIN
DOUT/RDY
NC
SYNC
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
1
2
3
4
5
6
7
8
AD7195
TOP VIEW
(Not to Scale)
24
23
22
21
20
19
18
17
DVDD
AVDD
DGND
AGND
BPDSW
NC
REFIN(–)
REFIN(+)
NOTES
1. NC = NO CONNECT.
2. CONNECT EXPOSED PAD TO AGND.
08771-005
AIN1
AIN2
NC
NC
NC
NC
AIN3
AIN4
9
10
11
12
13
14
15
16
ACX2
ACX2
ACX1
ACX1
AVDD
AGND
NC
AINCOM
Figure 5.Pin Configuration
Table 5. Pin Function Descriptions
Pin No.
1
Mnemonic
ACX2
2
ACX2
3
ACX1
4
ACX1
5
6
7
8
9
AVDD
AGND
NC
AINCOM
AIN1
10
AIN2
11
12
13
14
15
NC
NC
NC
NC
AIN3
16
AIN4
17
REFIN(+)
18
19
REFIN(−)
NC
Description
Digital Output. Provides a signal that can be used to control the reversing of the bridge excitation in ac
excited bridge applications. In ac mode, ACX2 toggles in anti-phase with ACX1. If the ACX bit equals zero (ac
excitation turned off), the ACX2 output remains low. When toggling, it is guaranteed to be nonoverlapping
with ACX1. The nonoverlap interval between ACX1 and ACX2 is 1/(master clock) which is equal to 200 ns
when a 4.92 MHz clock is used.
Digital Output. Provides a signal that can be used to control the reversing of the bridge excitation in ac
excited bridge applications. This output is the inverse of ACX2. If the ACX bit equals zero (ac excitation turned
off), the ACX2 output remains high.
Digital Output. Provides a signal that can be used to control the reversing of the bridge excitation in ac
excited bridge applications. When ACX1 is high, the bridge excitation is taken as normal and when ACX1 is
low, the bridge excitation is reversed (chopped). If the Bit ACX equals zero (ac excitation turned off), the ACX1
output remains high.
Digital Output. Provides a signal that can be used to control the reversing of the bridge excitation in ac
excited bridge applications. This output is the inverse of ACX1. When ACX1 is low, the bridge excitation is
taken as normal and when ACX1 is high, the bridge excitation is reversed (chopped). If the ACX bit equals
zero (ac excitation turned off), the ACX1 output remains low.
Analog Supply Voltage, 4.75 V to 5.25 V. AVDD is independent of DVDD.
Analog Ground Reference Point.
No Connect. This pin should be tied to AGND.
Analog inputs AIN1 to AIN4 are referenced to this input when configured for pseudo differential operation.
Analog Input. This pin can be configured as the positive input of a fully differential input pair when used with
AIN2 or as a pseudo differential input when used with AINCOM.
Analog Input. This pin can be configured as the negative input of a fully differential input pair when used
with AIN1 or as a pseudo differential input when used with AINCOM.
No Connect. This pin should be tied to AGND.
No Connect. This pin should be tied to AGND.
No Connect. This pin should be tied to AGND.
No Connect. This pin should be tied to AGND.
Analog Input. This pin can be configured as the positive input of a fully differential input pair when used with
AIN4 or as a pseudo differential input when used with AINCOM.
Analog Input. This pin can be configured as the negative input of a fully differential input pair when used
with AIN3 or as a pseudo differential input when used with AINCOM.
Positive Reference Input. An external reference can be applied between REFIN(+) and REFIN(−). REFIN(+) can
lie anywhere between AVDD and AGND + 1 V. The nominal reference voltage, (REFIN(+) − REFIN(−)), is AVDD,
but the part functions with a reference from 1 V to AVDD.
Negative Reference Input. This reference input can lie anywhere between AGND and AVDD − 1 V.
No Connect. This pin should be tied to AGND.
Rev. 0 | Page 9 of 44
AD7195
Pin No.
20
21
22
23
24
25
Mnemonic
BPDSW
AGND
DGND
AVDD
DVDD
SYNC
26
27
NC
DOUT/RDY
28
DIN
29
MCLK1
30
MCLK2
31
SCLK
32
CS
Description
Bridge Power-Down Switch to AGND.
Analog Ground Reference Point.
Digital Ground Reference Point.
Analog Supply Voltage, 4.75 V to 5.25 V. AVDD is independent of DVDD.
Digital Supply Voltage, 2.7 V to 5.25 V. DVDD is independent of AVDD.
Logic input that allows for synchronization of the digital filters and analog modulators when using a number
of AD7195 devices. While SYNC is low, the nodes of the digital filter, the filter control logic, and the
calibration control logic are reset, and the analog modulator is also held in its reset state. SYNC does not
affect the digital interface but does reset RDY to a high state if it is low. SYNC has a pull-up resistor internally
to DVDD.
No Connect. This pin should be tied to AGND.
Serial Data Output/Data Ready Output. DOUT/RDY serves a dual purpose. It functions as a serial data output
pin to access the output shift register of the ADC. The output shift register can contain data from any of the
on-chip data or control registers. In addition, DOUT/RDY operates as a data ready pin, going low to indicate
the completion of a conversion. If the data is not read after the conversion, the pin goes high before the next
update occurs. The DOUT/RDY falling edge can be used as an interrupt to a processor, indicating that valid
data is available. With an external serial clock, the data can be read using the DOUT/RDY pin. With CS low, the
data-/control-word information is placed on the DOUT/RDY pin on the SCLK falling edge and is valid on the
SCLK rising edge.
Serial Data Input to the Input Shift Register on the ADC. Data in this shift register is transferred to the control
registers in the ADC, with the register selection bits of the communications register identifying the appropriate register.
When the master clock for the device is provided externally by a crystal, the crystal is connected between
MCLK1 and MCLK2.
Master Clock Signal for the Device. The AD7195 has an internal 4.92 MHz clock. This internal clock can be
made available on the MCLK2 pin. The clock for the AD7195 can be provided externally also in the form of a
crystal or external clock. A crystal can be tied across the MCLK1 and MCLK2 pins. Alternatively, the MCLK2 pin
can be driven with a CMOS-compatible clock and the MCLK1 pin left unconnected.
Serial Clock Input. This serial clock input is for data transfers to and from the ADC. The SCLK has a Schmitttriggered input, making the interface suitable for opto-isolated applications. The serial clock can be
continuous with all data transmitted in a continuous train of pulses. Alternatively, it can be a noncontinuous
clock with the information transmitted to or from the ADC in smaller batches of data.
Chip Select Input. This is an active low logic input used to select the ADC. CS can be used to select the ADC in
systems with more than one device on the serial bus or as a frame synchronization signal in communicating
with the device. CS can be hardwired low, allowing the ADC to operate in 3-wire mode with SCLK, DIN, and
DOUT used to interface with the device.
Rev. 0 | Page 10 of 44
AD7195
TYPICAL PERFORMANCE CHARACTERISTICS
8,388,760
30
8,388,758
25
8,388,756
FREQUENCY
CODE
20
8,388,754
8,388,752
15
10
8,388,750
0
200
400
600
800
1000
SAMPLE
0
8,388,490
08771-006
8,388,746
8,388,576
8,388,662
8,388,748
CODE
8,388,834
8,388,920
08771-009
5
8,388,748
Figure 9. Noise Distribution Histogram (VREF = 5 V,
Output Data Rate = 4800 Hz, Gain = 128, Chop Disabled, Sinc4 Filter)
Figure 6. Noise (VREF = 5 V, Output Data Rate = 4.7 Hz, Gain = 128,
Chop Disabled, Sinc4 Filter)
250
8,388,820
8,388,800
8,388,780
200
150
8,388,740
CODE
FREQUENCY
8,388,760
8,388,720
8,388,700
100
8,388,680
50
8,388,660
CODE
0
100
200
300
400
500
600
700
800
900
08771-010
8,388,620
08771-007
8,388,760
8,388,758
8,388,756
8,388,754
8,388,752
8,388,750
8,388,746
8,388,748
8,388,640
0
1000
SAMPLES
Figure 10. Noise (VREF = 5 V, Output Data Rate = 4800 Hz, Gain = 1,
Chop Disabled, Sinc4 Filter)
Figure 7. Noise Distribution Histogram (VREF = 5 V,
Output Data Rate = 4.7 Hz, Gain = 128, Chop Disabled, Sinc4 Filter)
80
8,388,950
8,388,900
70
8,388,850
60
FREQUENCY
8,388,800
8,388,700
8,388,650
50
40
30
8,388,600
20
8,388,550
8,388,450
0
100
200
300
400
500
600
700
800
900
1000
SAMPLES
Figure 8. Noise (VREF = 5 V, Output Data Rate = 4800 Hz, Gain = 128,
Chop Disabled, Sinc4 Filter)
0
8,388,620
8,388,660
8,388,700
8,388,740
CODE
8,388,780
8,388,820
Figure 11. Noise Distribution Histogram (VREF = 5 V,
Output Data Rate = 4800 Hz, Gain = 1, Chop Disabled, Sinc4 Filter)
Rev. 0 | Page 11 of 44
08771-011
10
8,388,500
08771-008
CODE
8,388,750
AD7195
0
3.0
–0.1
2.0
OFFSET (µV)
INL (ppm of FSR)
–0.2
1.0
0
–0.3
–0.4
–1.0
–0.5
–2.0
–1.5
–1.0
–0.5
0
0.5
1.0
1.5
2.0
2.5
VIN (V)
–0.7
–60
–40
–20
0
20
40
60
80
100
120
TEMERATURE (°C)
Figure 12. INL (Gain = 1)
08771-015
–2.0
08771-012
–3.0
–2.5
–0.6
Figure 15. Offset Error (Gain = 128, Chop Disabled)
1.000008
6
1.000007
4
1.000005
GAIN
INL (ppm of FSR)
1.000006
2
0
1.000004
1.000003
–2
1.000002
–4
0
0.005
0.010
0.015
0.020
VIN (V)
1.000000
–60
08771-013
–6
–0.020 –0.015 –0.010 –0.005
–20
0
20
40
60
80
100
120
100
120
TEMPERATURE (°C)
Figure 16. Gain Error (Gain = 1, Chop Disabled)
Figure 13. INL (Gain = 128)
128.003
66
128.002
64
128.001
GAIN
62
60
128.000
127.999
58
127.998
56
–40
–20
0
20
40
60
80
100
120
TEMPERATURE (°C)
140
Figure 14. Offset Error (Gain = 1, Chop Disabled)
127.996
–60
–40
–20
0
20
40
60
80
TEMPERATURE (°C)
Figure 17. Gain Error (Gain = 128, Chop Disabled)
Rev. 0 | Page 12 of 44
08771-017
54
–60
127.997
08771-014
OUTPUT VOLTAGE (µV)
–40
08771-016
1.000001
AD7195
RMS NOISE AND RESOLUTION
The tables in this section show the rms noise, peak-to-peak
noise, effective resolution, and noise-free (peak-to-peak) resolution of the AD7195 for various output data rates and gain settings,
with chop disabled and chop enabled for the sinc4 and sinc3
filters. The numbers given are for the bipolar input range with
the external 5 V reference. These numbers are typical and are
generated with a differential input voltage of 0 V when the ADC
is continuously converting on a single channel. It is important
to note that the effective resolution is calculated using the rms
noise, whereas the peak-to-peak resolution is calculated based
on peak-to-peak noise. The peak-to-peak resolution represents
the resolution for which there is no code flicker.
SINC4 CHOP DISABLED
Table 6. RMS Noise (nV) vs. Gain and Output Data Rate
Filter Word
(Decimal)
1023
640
480
96
80
32
16
5
2
1
Output Data
Rate (Hz)
4.7
7.5
10
50
60
150
300
960
2400
4800
Settling
Time (ms)
852.5
533
400
80
66.7
26.7
13.3
4.17
1.67
0.83
Gain of 1
280
390
470
1000
1100
1460
1900
3000
5000
14,300
Gain of 8
96
120
130
150
170
220
285
480
780
1920
Gain of 16
50
54
56
78
88
125
170
280
440
1000
Gain of 32
22
28
31
45
52
75
100
175
280
550
Gain of 64
10
12
14
33
36
55
75
140
220
380
Gain of 128
8.5
10.5
11.5
28
31
48
67
121
198
295
Gain of 16
250
290
300
450
480
750
1000
1800
2800
6000
Gain of 32
130
150
190
280
300
410
600
1100
1700
3500
Gain of 64
65
80
100
180
220
340
440
810
1400
2400
Gain of 128
56
65
70
170
190
310
430
710
1200
1900
Gain of 641
23.6 (21.2)
23.4 (20.9)
23.3 (20.6)
22.2 (19.7)
22.1 (19.4)
21.5 (18.8)
21 (18.4)
20.2 (17.6)
19.5 (16.8)
18.8 (16)
Gain of 1281
23.1 (20.4)
22.8 (20.2)
22.7 (20.1)
21.4 (18.8)
21.3 (18.6)
20.6 (17.9)
20.1 (17.5)
19.3 (16.7)
18.6 (16)
18 (15.3)
Table 7. Peak-to-Peak Noise (nV) vs. Gain and Output Data Rate
Filter Word
(Decimal)
1023
640
480
96
80
32
16
5
2
1
Output Data
Rate (Hz)
4.7
7.5
10
50
60
150
300
960
2400
4800
Settling
Time (ms)
852.5
533
400
80
66.7
26.7
13.3
4.17
1.67
0.83
Gain of 1
1600
2200
3000
6000
7200
8300
11,000
20,000
32,000
86,000
Gain of 8
500
650
670
900
1100
1500
1700
3000
5100
13,000
Table 8. Effective Resolution (Peak-to-Peak Resolution) vs. Gain and Output Data Rate
Filter Word
(Decimal)
1023
640
480
96
80
32
16
5
2
1
1
Output Data
Rate (Hz)
4.7
7.5
10
50
60
150
300
960
2400
4800
Settling
Time (ms)
852.5
533
400
80
66.7
26.7
13.3
4.17
1.67
0.83
Gain of 1 1
24 (22.6)
24 (22.1)
24 (21.7)
23.3 (20.7)
23.1 (20.4)
22.7 (20.2)
22.3 (19.8)
21.7 (18.9)
20.9 (18.3)
19.4 (16.8)
Gain of 81
23.6 (21.3)
23.4 (20.9)
23.3 (20.8)
23 (20.4)
22.8 (20.1)
22.4 (19.7)
22.1 (19.5)
21.3 (18.7)
20.6 (17.9)
19.3 (16.6)
Gain of 161
23.6 (21.3)
23.4 (20.9)
23.3 (20.8)
22.9 (20.4)
22.8 (20)
22.3 (19.7)
21.8 (19.3)
21.1 (18.4)
20.4 (17.7)
19.3 (16.4)
The output peak-to-peak (p-p) resolution is listed in parentheses.
Rev. 0 | Page 13 of 44
Gain of 321
23.6 (21.2)
23.4 (20.9)
23.3 (20.8)
22.7 (20.1)
22.5 (20 )
22 (19.5)
21.6 (19)
20.8 (18.1)
20.1 (17.5)
19.1 (16.4)
AD7195
SINC3 CHOP DISABLED
Table 9. RMS Noise (nV) vs. Gain and Output Data Rate
Filter Word
(Decimal)
1023
640
480
96
80
32
16
5
2
1
Output Data
Rate (Hz)
4.7
7.5
10
50
60
150
300
960
2400
4800
Settling
Time (ms)
639.4
400
300
60
50
20
10
3.13
1.25
0.625
Gain of 1
290
470
610
1100
1200
1500
1950
4000
56,600
442,000
Gain of 8
125
135
145
160
170
230
308
590
7000
55,000
Gain of 16
53
56
58
86
95
130
175
330
3500
28,000
Gain of 32
24
29
32
50
55
80
110
200
1800
14,000
Gain of 64
10.5
13
16
35
40
58
83
150
900
7000
Gain of 128
9
11.5
12.5
29
32
50
73
133
490
3450
Gain of 16
260
340
360
480
600
710
1000
2200
22,000
170,000
Gain of 32
140
150
200
290
300
470
670
1200
12,000
79,000
Gain of 64
65
84
100
200
240
360
470
850
5600
41,000
Gain of 128
56
60
70
180
200
310
500
800
3100
24,000
Table 10. Peak-to-Peak Noise (nV) vs. Gain and Output Data Rate
Filter Word
(Decimal)
1023
640
480
96
80
32
16
5
2
1
Output Data
Rate (Hz)
4.7
7.5
10
50
60
150
300
960
2400
4800
Settling
Time (ms)
639.4
400
300
60
50
20
10
3.13
1.25
0.625
Gain of 1
1700
2400
3000
6600
6800
8900
13,000
25,000
310,000
2,600,000
Gain of 8
750
800
900
1000
1100
1400
2000
3400
41,000
300,000
Table 11. Effective Resolution (Peak-to-Peak Resolution) vs. Gain and Output Data Rate
Filter Word
(Decimal)
1023
640
480
96
80
32
16
5
2
1
1
Output Data
Rate (Hz)
4.7
7.5
10
50
60
150
300
960
2400
4800
Settling
Time (ms)
639.4
400
300
60
50
20
10
3.13
1.25
0.625
Gain of 1 1
24 (22.5)
24 (22)
24 (22)
23.1 (20.5)
23 (20.5)
22.7 (20)
22.3 (19.5)
21.3 (18.5)
17.4 (14.9)
14.5 (11.9)
Gain of 81
23.5 (21)
23.3 (20.8)
23.2 (20.5)
22.9 (20.3)
22.8 (20.1)
22.4 (19.8)
22 (19.3)
21 (18.5)
17.4 (14.9)
14.5 (11.9)
Gain of 161
23.5 (21)
23.3 (20.8)
23.2 (20.5)
22.8 (20.3)
22.6 (20)
22.2 (19.7)
21.8 (19.3)
20.9 (18.1)
17.4 (14.8)
14.4 (11.8)
The output peak-to-peak (p-p) resolution is listed in parentheses.
Rev. 0 | Page 14 of 44
Gain of 321
23.5 (21)
23.3 (20.8)
23.2 (20.5)
22.6 (20)
22.4 (20)
21.9 (19.3)
21.4 (18.8)
20.6 (18)
17.4 (14.7)
14.4 (11.8)
Gain of 641
23.5 (21)
23.3 (20.8)
23.2 (20.5)
22.1 (19.6)
21.9 (19.3)
21.4 (18.7)
20.8 (18.3)
20 (17.5)
17.4 (14.7)
14.4 (11.8)
Gain of 1281
23 (20.4)
22.7 (20.3)
22.6 (20.1)
21.4 (18.7)
21.2 (18.6)
20.6 (17.9)
20 (17.3)
19.2 (16.6)
17.3 (14.6)
14.4 (11.7)
AD7195
SINC4 CHOP ENABLED
Table 12. RMS Noise (nV) vs. Gain and Output Data Rate
Filter Word
(Decimal)
1023
640
480
96
80
32
16
5
2
1
Output Data
Rate (Hz)
1.175
1.875
2.5
12.5
15
37.5
75
240
600
1200
Settling
Time (ms)
1702
1067
800
160
133
53.3
26.7
8.33
3.33
1.67
Gain of 1
198
276
332
707
778
990
1344
2192
3606
9900
Gain of 8
85
92
99
127
141
156
191
325
523
1345
Gain of 16
41
45
46
61
62
85
106
184
297
680
Gain of 32
18
22
23
34
35
51
67
120
191
368
Gain of 64
7
8.5
10
23
24
38
51
92
148
248
Gain of 128
6
7
8
18
21
33
45
78
134
200
Gain of 16
212
248
255
368
424
530
707
1273
1980
4950
Gain of 32
92
106
134
198
212
290
424
778
1202
2475
Gain of 64
46
57
71
127
156
240
311
573
990
1697
Gain of 128
40
46
50
120
134
219
304
502
850
1345
Gain of 641
24 (21.7)
23.9 (21.4)
23.8 (21.1)
22.7 (20.2)
22.6 (19.9)
22 (19.3)
21.5 (18.9)
20.7 (18.1)
20 (17.3)
19.3 (16.5)
Gain of 1281
23.6 (20.9)
23.3 (20.7)
23.2 (20.6)
21.9 (19.3)
21.8 (19.1)
21.1 (18.4)
20.6 (18)
19.8 (17.2)
19.1 (16.5)
18.5 (15.8)
Table 13. Peak-to-Peak Noise (nV) vs. Gain and Output Data Rate
Filter Word
(Decimal)
1023
640
480
96
80
32
16
5
2
1
Output Data
Rate (Hz)
1.175
1.875
2.5
12.5
15
37.5
75
240
600
1200
Settling
Time (ms)
1702
1067
800
160
133
53.3
26.7
8.33
3.33
1.67
Gain of 1
1131
1556
2121
4243
5091
5870
7780
14,142
22,627
60,800
Gain of 8
474
495
530
707
849
1061
1202
2121
3606
9192
Table 14. Effective Resolution (Peak-to-Peak Resolution) vs. Gain and Output Data Rate
Filter Word
(Decimal)
1023
640
480
96
80
32
16
5
2
1
1
Output Data
Rate (Hz)
1.175
1.875
2.5
12.5
15
37.5
75
240
600
1200
Settling
Time (ms)
1702
1067
800
160
133
53.3
26.7
8.33
3.33
1.67
Gain of 1 1
24 (23.1)
24 (22.6)
24 (22.2)
23.8 (21.2)
23.6 (20.9)
23.2 (20.7)
22.8 (20.3)
22.2 (19.4)
21.4 (18.8)
19.9 (17.3)
Gain of 81
24 (21.8)
23.9 (21.4)
23.8 (21.3)
23.5 (20.9)
23.3 (20.6)
22.9 (20.2)
22.6 (20)
21.8 (19.2)
21.1 (18.4)
19.8 (17.1)
Gain of 161
24 (21.8)
23.9 (21.4)
23.8 (21.3)
23.4 (20.9)
23.3 (20.5)
22.8 (20.2)
22.3 (19.8)
21.6 (18.9)
20.9 (18.2)
19.8 (16.9)
Gain of 321
24 (21.7)
23.9 (21.4)
23.8 (21.3)
23.2 (20.6)
23 (20.5)
22.5 (20)
22.1 (19.5)
21.3 (18.6)
20.6 (18)
19.6 (16.9)
The output peak-to-peak (p-p) resolution is listed in parentheses.
When ac excitation is enabled, the rms noise and resolution is the same as for chop enabled mode.
Rev. 0 | Page 15 of 44
AD7195
SINC3 CHOP ENABLED
Table 15. RMS Noise (nV) vs. Gain and Output Data Rate
Filter Word
(Decimal)
1023
640
480
96
80
32
16
5
2
1
Output Data
Rate (Hz)
1.56
2.5
3.33
16.6
20
50
100
320
800
1600
Settling
Time (ms)
1282
800
600
120
100
40
20
6.25
2.5
1.25
Gain of 1
205
332
431
778
849
1061
1379
2828
40,022
312,540
Gain of 8
88
95
103
113
120
163
218
417
4950
38,890
Gain of 16
37
40
41
61
67
92
124
233
2475
19,800
Gain of 32
17
21
23
35
39
57
78
141
1273
9900
Gain of 64
7.5
9
11.5
25
28
41
59
106
636
4950
Gain of 128
6.5
8
9
21
23
35
52
94
346
2440
Gain of 16
184
240
255
318
424
474
707
1556
15,560
120,200
Gain of 32
92
120
141
198
205
382
474
849
8485
55,870
Gain of 64
46
59
71
141
170
255
332
601
3960
29,000
Gain of 128
40
42
49
127
141
219
354
566
2192
16,970
Gain of 641
24 (21.5)
23.8 (21.3)
23.7 (21)
22.6 (20.1)
22.4 (19.8)
21.9 (19.2)
21.3 (18.8)
20.5 (18)
17.9 (15.2)
14.9 (12.3)
Gain of 1281
23.5 (20.9)
23.2 (20.8)
23.1 (20.6)
21.9 (19.2)
21.7 (19.1)
21.1 (18.4)
20.5 (17.8)
19.7 (17.1)
17.8 (15.1)
14.9 (12.2)
Table 16. Peak-to-Peak Noise (nV) vs. Gain and Output Data Rate
Filter Word
(Decimal)
1023
640
480
96
80
32
16
5
2
1
Output Data
Rate (Hz)
1.56
2.5
3.33
16.6
20
50
100
320
800
1600
Settling
Time (ms)
1282
800
600
120
100
40
20
6.25
2.5
1.25
Gain of 1
1202
1697
2121
4667
4808
6293
9192
17,680
219,200
1,838,500
Gain of 8
530
566
636
686
707
990
1414
2404
29,000
212,200
Table 17. Effective Resolution (Peak-to-Peak Resolution) vs. Gain and Output Data Rate
Filter Word
(Decimal)
1023
640
480
96
80
32
16
5
2
1
1
Output Data
Rate (Hz)
1.56
2.5
3.33
16.6
20
320
100
320
800
1600
Settling
Time (ms)
1282
800
600
120
100
40
20
6.25
2.5
1.25
Gain of 1 1
24 (23)
24 (22.5)
24 (22.5)
23.6 (21)
23.5 (21)
23.2 (20.5)
22.8 (20)
21.8 (19)
17.9 (15.4)
15 (12.4)
Gain of 81
24 (21.5)
23.8 (21.3)
23.7 (21)
23.4 (20.8)
23.3 (20.6)
22.9 (20.3)
22.5 (19.8)
21.5 (19)
17.9 (15.4)
15 (12.4)
Gain of 161
24 (21.5)
23.8 (21.3)
23.7 (21)
23.3 (20.8)
23.1 (20.5)
22.7 (20.2)
22.3 (19.8)
21.4 (18.6)
17.9 (15.3)
14.9 (12.3)
Gain of 321
24 (21.5)
23.8 (21.3)
23.7 (21)
23.1 (20.5)
22.9 (20.5)
22.4 (19.8)
21.9 (19.3)
21.1 (18.5)
17.9 (15.2)
14.9 (12.3)
The output peak-to-peak (p-p) resolution is listed in parentheses.
When ac excitation is enabled, the rms noise and resolution is the same as for chop enabled mode.
Rev. 0 | Page 16 of 44
AD7195
ON-CHIP REGISTERS
The ADC is controlled and configured via a number of on-chip registers described on the following pages. In the following descriptions,
the term set implies a Logic 1 state and cleared implies a Logic 0 state, unless otherwise noted.
Table 18. Register Summary
Register
Communications
Addr.
00
Dir.
W
Default
00
Bit 7
WEN
Bit 6
R/W
Status
Mode
00
R
80
RDY
ERR
01
R/W
080060
Mode select
SINC3
0
FS7
FS6
Chop (MSB)
ACX
CH7
CH6
BURN
REFDET
D23 (MSB)
D15
D7
1
0
OF23 (MSB)
OF15
OF7
FS23 (MSB)
FS15
FS7
Configuration
02
R/W
000117
Data
03
R
000000
ID
GPOCON
Offset
04
05
06
R
R/W
R/W
A6
00
800000
Full Scale
07
R/W
5XXXX0
D22
D14
D6
0
BPDSW
OF22
OF14
OF6
FS22
FS14
FS6
Bit 5
Bit 4
Bit 3
Register address
NOREF PARITY
0
Bit 2
CREAD
Bit 1
0
Bit 0
0
CHD2
CHD1
CHD0
ENPAR
FS5
0
CH5
0
DAT_STA
0
FS4
0
CH4
BUF
CLK1
SINGLE
FS3
0
CH3
U/B
CLK0
REJ60
FS2
0
CH2
G2
0
FS9
FS1
0
CH1
G1
0
FS8
FS0 (LSB)
0
CH0
G0 (LSB)
D21
D13
D5
1
0
OF21
OF13
OF5
FS21
FS13
FS5
D20
D12
D4
0
0
OF20
OF12
OF4
FS20
FS12
FS4
D19
D11
D3
0
0
OF19
OF11
OF3
FS19
FS11
FS3
D18
D10
D2
1
0
OF18
OF10
OF2
FS18
FS10
FS2
D17
D9
D1
1
0
OF17
OF9
OF1
FS17
FS9
FS1
D16
D8
D0 (LSB)
0
0
OF16
OF8
OF0 (LSB)
FS16
FS8
FS0 (LSB)
Rev. 0 | Page 17 of 44
AD7195
COMMUNICATIONS REGISTER
(RS2, RS1, RS0 = 0, 0, 0)
The communications register is an 8-bit write-only register.
All communications to the part must start with a write
operation to the communications register. The data written
to the communications register determines whether the next
operation is a read or a write operation and in which register
this operation takes place. For read or write operations, when
the subsequent read or write operation to the selected register
is complete, the interface returns to where it expects a write
operation to the communications register. This is the default
CR7
WEN(0)
CR6
R/W(0)
CR5
RS2(0)
CR4
RS1(0)
state of the interface and, on power-up or after a reset, the
ADC is in this default state waiting for a write operation to
the communications register. In situations where the interface
sequence is lost, a write operation of at least 40 serial clock
cycles with DIN high returns the ADC to this default state by
resetting the entire part. Table 19 outlines the bit designations
for the communications register. CR0 through CR7 indicate the
bit location, CR denoting that the bits are in the communications
register. CR7 denotes the first bit of the data stream. The
number in parentheses indicates the power-on/reset default
status of that bit.
CR3
RS0(0)
CR2
CREAD(0)
CR1
0
CR0
0
Table 19. Communications Register Bit Designations
Bit Location
CR7
Bit Name
WEN
CR6
R/W
CR5 to CR3
RS2 to RS0
CR2
CREAD
CR1 to CR0
0
Description
Write enable bit. For a write to the communications register to occur, 0 must be written to this bit. If a 1 is
the first bit written, the part does not clock on to subsequent bits in the register; rather, it stays at this bit
location until a 0 is written to this bit. After a 0 is written to the WEN bit, the next seven bits are loaded to
the communications register. Idling the DIN pin high between data transfers minimizes the effects of
spurious SCLK pulses on the serial interface.
A 0 in this bit location indicates that the next operation is a write to a specified register. A 1 in this position
indicates that the next operation is a read from the designated register.
Register address bits. These address bits are used to select which registers of the ADC are selected during
the serial interface communication (see Table 20).
Continuous read of the data register. When this bit is set to 1 (and the data register is selected), the serial
interface is configured so that the data register can be continuously read; that is, the contents of the data
register are automatically placed on the DOUT pin when the SCLK pulses are applied after the RDY pin
goes low to indicate that a conversion is complete. The communications register does not have to be
written to for subsequent data reads. To enable continuous read, the Instruction 01011100 must be written
to the communications register. To disable continuous read, the Instruction 01011000 must be written to
the communications register while the RDY pin is low. While continuous read is enabled, the ADC monitors
activity on the DIN line so that it can receive the instruction to disable continuous read. Additionally, a reset
occurs if 40 consecutive 1s are seen on DIN. Therefore, hold DIN low until an instruction is written to the
device.
These bits must be programmed to Logic 0 for correct operation.
Table 20. Register Selection
RS2
0
0
0
0
0
1
1
1
1
RS1
0
0
0
1
1
0
0
1
1
RS0
0
0
1
0
1
0
1
0
1
Register
Communications register during a write operation
Status register during a read operation
Mode register
Configuration register
Data register/data register plus status information
ID register
GPOCON register
Offset register
Full-scale register
Rev. 0 | Page 18 of 44
Register Size
8 bits
8 bits
24 bits
24 bits
24 bits/32 bits
8 bits
8 bits
24 bits
24 bits
AD7195
STATUS REGISTER
(RS2, RS1, RS0 = 0, 0, 0; Power-On/Reset = 0x80)
The status register is an 8-bit read-only register. To access the ADC status register, the user must write to the communications register,
select the next operation to be a read, and load Bit RS2, Bit RS1, and Bit RS0 with 0. Table 21 outlines the bit designations for the status
register. SR0 through SR7 indicate the bit locations, SR denoting that the bits are in the status register. SR7 denotes the first bit of the data
stream. The number in parentheses indicates the power-on/reset default status of that bit.
SR7
RDY(1)
SR6
ERR(0)
SR5
NOREF(0)
SR4
PARITY(0)
SR3
0
SR2
CHD2(0)
SR1
CHD1(0)
SR0
CHD0(0)
Table 21. Status Register Bit Designations
Bit Location
SR7
Bit Name
RDY
SR6
ERR
SR5
NOREF
SR4
PARITY
SR3
SR2 to SR0
0
CHD2 to
CHD0
Description
Ready bit for the ADC. This bit is cleared when data is written to the ADC data register. The RDY bit is set
automatically after the ADC data register is read, or a period of time before the data register is updated,
with a new conversion result to indicate to the user that the conversion data should not be read. It is also
set when the part is placed in power-down mode or idle mode or when SYNC is taken low. The end of a
conversion is also indicated by the DOUT/RDY pin. This pin can be used as an alternative to the status
register for monitoring the ADC for conversion data.
ADC error bit. This bit is written to at the same time as the RDY bit. This bit is set to indicate that the result
written to the ADC data register is clamped to all 0s or all 1s. Error sources include overrange or underrange, or the absence of a reference voltage. This bit is cleared when the result written to the data register
is within the allowed analog input range again.
No external reference bit. This bit is set to indicate that the reference is at a voltage that is below a specified
threshold. When set, conversion results are clamped to all 1s. This bit is cleared to indicate that a valid
reference is applied to the selected reference pins. The NOREF bit is enabled by setting the REFDET bit in
the configuration register to 1.
Parity check of the data register. If the ENPAR bit in the mode register is set, the PARITY bit is set if there is
an odd number of 1s in the data register. It is cleared if there is an even number of 1s in the data register.
The DAT_STA bit in the mode register should be set when the parity check is used. When the DAT_STA bit is
set, the contents of the status register are transmitted along with the data for each data register read.
This bit is set to 0.
These bits indicate which channel corresponds to the data register contents. They do not indicate which
channel is presently being converted but indicate which channel was selected when the conversion
contained in the data register was generated.
MODE REGISTER
(RS2, RS1, RS0 = 0, 0, 1; Power-On/Reset = 0x080060)
The mode register is a 24-bit register from which data can be read or to which data can be written. This register is used to select the
operating mode, the output data rate, and the clock source. Table 22 outlines the bit designations for the mode register. MR0 through
MR23 indicate the bit locations, MR denoting that the bits are in the mode register. MR23 denotes the first bit of the data stream. The
number in parentheses indicates the power-on/reset default status of that bit. Any write to the mode register resets the modulator and
filter and sets the RDY bit.
MR23
MD2(0)
MR15
SINC3(0)
MR7
FS7(0)
MR22
MD1(0)
MR14
0
MR6
FS6(1)
MR21
MD0(0)
MR13
ENPAR(0)
MR5
FS5(1)
MR20
DAT_STA(0)
MR12
0
MR4
FS4(0)
MR19
CLK1(1)
MR11
SINGLE(0)
MR3
FS3(0)
Rev. 0 | Page 19 of 44
MR18
CLK0(0)
MR10
REJ60(0)
MR2
FS2(0)
MR17
0
MR9
FS9(0)
MR1
FS1(0)
MR16
0
MR8
FS8(0)
MR0
FS0(0)
AD7195
Table 22. Mode Register Bit Designations
Bit Location
MR23 to MR21
MR20
Bit Name
MD2 to MD0
DAT_STA
MR19, MR18
CLK1, CLK0
MR17, MR16
MR15
0
SINC3
MR14
MR13
0
ENPAR
MR12
MR11
0
SINGLE
MR10
REJ60
MR9 to MR0
FS9 to FS0
Description
Mode select bits. These bits select the operating mode of the AD7195 (see Table 23).
This bit enables the transmission of status register contents after each data register read. When
DAT_STA is set, the contents of the status register are transmitted along with each data register read.
This function is useful when several channels are selected because the status register identifies the
channel to which the data register value corresponds.
These bits select the clock source for the AD7195. Either the on-chip 4.92 MHz clock or an external
clock can be used. The ability to use an external clock allows several AD7195 devices to be synchronized. Also, 50 Hz/60 Hz rejection is improved when an accurate external clock drives the AD7195.
CLK1
CLK0
ADC Clock Source
0
0
External crystal. The external crystal is connected from MCLK1 to MCLK2.
0
1
External clock. The external clock is applied to the MCLK2 pin.
1
0
Internal 4.92 MHz clock. Pin MCLK2 is tristated.
1
1
Internal 4.92 MHz clock. The internal clock is available on MCLK2.
These bits must be programmed with a Logic 0 for correct operation.
Sinc3 filter select bit. When this bit is cleared, the sinc4 filter is used (default value). When this bit is set,
the sinc3 filter is used. The benefit of the sinc3 filter compared to the sinc4 filter is its lower settling time.
For a given output data rate, fADC, the sinc3 filter has a settling time of 3/fADC while the sinc4 filter has a
settling time of 4/fADC when chop is disabled. The sinc4 filter, due to its deeper notches, gives better
50 Hz/60 Hz rejection. At low output data rates, both filters give similar rms noise and similar no
missing codes for a given output data rate. At higher output data rates (FS values less than 5), the
sinc4 filter gives better performance than the sinc3 filter for rms noise and no missing codes.
This bit must be programmed with a Logic 0 for correct operation.
Enable parity bit. When ENPAR is set, parity checking on the data register is enabled. The DAT_STA bit
in the mode register should be set when the parity check is used. When the DAT_STA bit is set, the
contents of the status register are transmitted along with the data for each data register read.
This bit must be programmed with a Logic 0 for correct operation.
Single cycle conversion enable bit. When this bit is set, the AD7195 settles in one conversion cycle so
that it functions as a zero-latency ADC. This bit has no effect when multiple analog input channels are
enabled or when the single conversion mode is selected.
This bit enables a notch at 60 Hz when the first notch of the sinc filter is at 50 Hz. When REJ60 is set, a
filter notch is placed at 60 Hz when the sinc filter first notch is at 50 Hz. This allows simultaneous 50 Hz/
60 Hz rejection.
Filter output data rate select bits. The 10 bits of data programmed into these bits determine the filter
cut-off frequency, the position of the first notch of the filter, and the output data rate for the part. In
association with the gain selection, they also determine the output noise (and, therefore, the effective
resolution) of the device (see Table 6 through Table 17). When chop is disabled and continuous
conversion mode is selected,
Output Data Rate = (MCLK/1024)/FS
where FS is the decimal equivalent of the code in Bit FS0 to Bit FS9 and is in the range 1 to 1023, and
MCLK is the master clock frequency. With a nominal MCLK of 4.92 MHz, this results in an output data
rate from 4.69 Hz to 4.8 kHz. With chop disabled, the first notch frequency is equal to the output data
rate when converting on a single channel. When chop is enabled,
Output Data Rate = (MCLK/1024)/(N × FS)
where FS is the decimal equivalent of the code in Bit FS0 to Bit FS9 and is in the range 1 to 1023, and
MCLK is the master clock frequency. With a nominal MCLK of 4.92 MHz, this results in a conversion rate
from 4.69/N Hz to 4.8/N kHz, where N is the order of the sinc filter. The sinc filter’s first notch frequency
is equal to N × output data rate. The chopping introduces notches at odd integer multiples of (output
data rate/2).
Rev. 0 | Page 20 of 44
AD7195
Table 23. Operating Modes
MD2
0
MD1
0
MD0
0
0
0
1
0
1
0
0
1
1
1
0
0
1
0
1
1
1
0
1
1
1
Mode
Continuous conversion mode (default). In continuous conversion mode, the ADC continuously performs
conversions and places the result in the data register. The DOUT/RDY pin and the RDY bit in the status register
go low when a conversion is complete. The user can read these conversions by setting the CREAD bit in the communications register to 1, which enables continuous read. When continuous read is enabled, the conversions are
automatically placed on the DOUT line when SCLK pulses are applied. Alternatively, the user can instruct the ADC
to output each conversion by writing to the communications register. After power-on, a reset, or a reconfiguration
of the ADC, the complete settling time of the filter is required to generate the first valid conversion. Subsequent
conversions are available at the selected output data rate, which is dependent on filter choice.
Single conversion mode. When single conversion mode is selected, the ADC powers up and performs a single
conversion on the selected channel. The internal clock requires up to 1 ms to power up and settle. The ADC then
performs the conversion, which requires the complete settling time of the filter. The conversion result is placed in
the data register. RDY goes low, and the ADC returns to power-down mode. The conversion remains in the data
register until another conversion is performed. RDY remains active (low) until the data is read or another conversion
is performed.
Idle mode. In idle mode, the ADC filter and modulator are held in a reset state even though the modulator clocks are
still provided.
Power-down mode. In power-down mode, all AD7195 circuitry, except the bridge power-down switch, is powered
down. The bridge power-down switch remains active because the user may need to power up the sensor prior to
powering up the AD7195 for settling reasons. The external crystal, if selected, remains active.
Internal zero-scale calibration. An internal short is automatically connected to the input. RDY goes high when the
calibration is initiated and returns low when the calibration is complete. The ADC is placed in idle mode following a
calibration. The measured offset coefficient is placed in the offset register of the selected channel.
Internal full-scale calibration. A full-scale input voltage is automatically connected to the input for this calibration.
RDY goes high when the calibration is initiated and returns low when the calibration is complete. The ADC is placed
in idle mode following a calibration. The measured full-scale coefficient is placed in the full-scale register of the
selected channel. A full-scale calibration is required each time the gain of a channel is changed to minimize the fullscale error.
System zero-scale calibration. The user should connect the system zero-scale input to the channel input pins as
selected by the CH7 to CH0 bits in the configuration register. RDY goes high when the calibration is initiated and
returns low when the calibration is complete. The ADC is placed in idle mode following a calibration. The measured
offset coefficient is placed in the offset register of the selected channel. A system zero-scale calibration is required
each time the gain of a channel is changed.
System full-scale calibration. The user should connect the system full-scale input to the channel input pins as
selected by the CH7 to CH0 bits in the configuration register. RDY goes high when the calibration is initiated and
returns low when the calibration is complete. The ADC is placed in idle mode following a calibration. The measured
full-scale coefficient is placed in the full-scale register of the selected channel. A full-scale calibration is required
each time the gain of a channel is changed.
CONFIGURATION REGISTER
(RS2, RS1, RS0 = 0, 1, 0; Power-On/Reset = 0x000117)
The configuration register is a 24-bit register from which data can be read or to which data can be written. This register is used to
configure the ADC for unipolar or bipolar mode, to enable or disable the buffer, to enable or disable the burnout currents, to select the
gain, and to select the analog input channel. Table 24 outlines the bit designations for the filter register. CON0 through CON23 indicate
the bit locations. CON denotes that the bits are in the configuration register. CON23 denotes the first bit of the data stream. The number
in parentheses indicates the power-on/reset default status of that bit.
CON23
CHOP(0)
CON15
CH7(0)
CON7
BURN(0)
CON22
ACX(0)
CON14
CH6(0)
CON6
REFDET(0)
CON21
0
CON13
CH5(0)
CON5
0
CON20
0
CON12
CH4(0)
CON4
BUF(1)
CON19
0
CON11
CH3(0)
CON3
U/B (0)
Rev. 0 | Page 21 of 44
CON18
0
CON10
CH2(0)
CON2
G2(1)
CON17
0
CON9
CH1(0)
CON1
G1(1)
CON16
0
CON8
CH0(1)
CON0
G0(1)
AD7195
Table 24. Configuration Register Bit Designations
Bit Location
CON23
Bit Name
CHOP
CON22
ACX
CON21 to CON16
CON15 to CON8
0
CH7 to CH0
CON7
BURN
CON6
REFDET
CON5
CON4
0
BUF
CON3
U/B
CON2 to CON0
G2 to G0
Description
Chop enable bit. When the CHOP bit is cleared, chop is disabled. When the CHOP bit is set, chop is
enabled. When chop is enabled, the offset and offset drift of the ADC are continuously removed.
However, this increases the conversion time and settling time of the ADC. For example, when FS = 96
decimal and the sinc4 filter is selected, the conversion time with chop enabled equals 80 ms and the
settling time equals 160 ms. With chop disabled, higher conversion rates are allowed. For an FS word
of 96 decimal and the sinc4 filter selected, the conversion time is 20 ms and the settling time is 80 ms.
However, at low gains, periodic calibrations may be required to remove the offset and offset drift.
When ax excitation is enabled, chop must be enabled also.
AC excitation enable bit. If the signal source to the AD7195 is ac excited, this bit must be set to 1. For
dc-excited inputs, this bit must be 0. With the ACX bit at 1, the AD7195 assumes that the voltage at the
AIN(+)/AIN(–) and REFIN(+)/REFIN(–) input terminals are reversed on alternate input sampling cycles
(that is, chopped). Note that when the AD7195 is performing internal zero-scale or full-scale calibrations, the ACX bit is treated as a 0, that is, the device performs these self-calibrations with dc excitation.
TheBitCHOP must be set to 1 when ac excitation is enabled.
These bits must be programmed with a Logic 0 for correct operation.
Channel select bits. These bits are used to select which channels are enabled on the AD7195 (see Table 25).
Several channels can be selected, and the AD7195 automatically sequences them. The conversion on
each channel requires the complete settling time. When performing calibrations or when accessing the
calibration registers, only one channel can be selected.
When this bit is set to 1, the 500 nA current sources in the signal path are enabled. When BURN = 0, the
burnout currents are disabled. The burnout currents can be enabled only when the buffer is active and
when chop is disabled.
Enables the reference detect function. When set, the NOREF bit in the status register indicates when the
external reference being used by the ADC is open circuit or less than 0.6 V maximum. The reference
detect circuitry operates only when the ADC is active.
This bit must be programmed with a Logic 0 for correct operation.
Enables the buffer on the analog inputs. If cleared, the analog inputs are unbuffered, lowering the
power consumption of the device. If this bit is set, the analog inputs are buffered, allowing the user to
place source impedances on the front end without contributing gain errors to the system. With the
buffer disabled, the voltage on the analog input pins can be from 50 mV below AGND to 50 mV above
AVDD. When the buffer is enabled, it requires some headroom; therefore, the voltage on any input pin
must be limited to 250 mV within the power supply rails.
Polarity select bit. When this bit is set, unipolar operation is selected. When this bit is cleared, bipolar
operation is selected.
Gain select bits. These bits are written by the user to select the ADC input range as follows:
G2
G1
G0
Gain
ADC Input Range (5 V Reference)
0
0
0
1
±5 V
0
0
1
Reserved
0
1
0
Reserved
0
1
1
8
±625 mV
1
0
0
16
±312.5 mV
1
0
1
32
±156.2 mV
1
1
0
64
±78.125 mV
1
1
1
128
±39.06 mV
Rev. 0 | Page 22 of 44
AD7195
Table 25. Channel Selection
Channel Enable Bits in the Configuration Register
CH7
CH6
CH5
CH4
CH3
CH2
CH1
CH0
1
1
1
1
1
1
1
1
Channel Enabled
Positive Input
Negative Input
AIN(+)
AIN(−)
AIN1
AIN2
AIN3
AIN4
Temperature sensor
AIN2
AIN2
AIN1
AINCOM
AIN2
AINCOM
AIN3
AINCOM
AIN4
AINCOM
Status Register
Bits CHD[2:0]
000
001
010
011
100
101
110
111
Calibration
Register Pair
0
1
None
0
0
1
2
3
DATA REGISTER
(RS2, RS1, RS0 = 0, 1, 1; Power-On/Reset = 0x000000)
The conversion result from the ADC is stored in this data register. This is a read-only, 24-bit register. On completion of a read operation
from this register, the RDY pin/bit is set. When the DAT_STA bit in the mode register is set to 1, the contents of the status register are
appended to each 24-bit conversion. This is advisable when several analog input channels are enabled because the three LSBs of the status
register (CHD2 to CHD0) identify the channel from which the conversion originated.
ID REGISTER
(RS2, RS1, RS0 = 1, 0, 0; Power-On/Reset = 0xA6)
The identification number for the AD7195 is stored in the ID register. This is a read-only register.
GPOCON REGISTER
(RS2, RS1, RS0 = 1, 0, 1; Power-On/Reset = 0x00)
The GPOCON register is an 8-bit register from which data can be read or to which data can be written. This register is used to enable the
general-purpose digital outputs.
Table 26 outlines the bit designations for the GPOCON register. GP0 through GP7 indicate the bit locations. GP denotes that the bits are
in the GPOCON register. GP7 denotes the first bit of the data stream. The number in parentheses indicates the power-on/reset default
status of that bit.
GP7
0
GP6
BPDSW(0)
GP5
0
GP4
0
GP3
0
GP2
0
GP1
0
GP0
0
Table 26. Register Bit Designations
Bit Location
GP7
GP 6
Bit Name
0
BPDSW
GP5 to GP0
0
Description
This bit must be programmed with a Logic 0 for correct operation.
Bridge power-down switch control bit. This bit is set by the user to close the bridge power-down switch
BPDSW to AGND. The switch can sink up to 30 mA. The bit is cleared by the user to open the bridge powerdown switch. When the ADC is placed in power-down mode, the bridge power-down switch remains active.
These bits must be programmed with a Logic 0 for correct operation.
Rev. 0 | Page 23 of 44
AD7195
FULL-SCALE REGISTER
OFFSET REGISTER
(RS2, RS1, RS0 = 1, 1, 1; Power-On/Reset = 0x5XXXX0)
(RS2, RS1, RS0 = 1, 1, 0; Power-On/Reset = 0x800000)
The offset register holds the offset calibration coefficient for the
ADC. The power-on reset value of the offset register is
0x800000. The AD7195 has four offset registers; therefore, each
channel has a dedicated offset register (see Table 25). Each of
these registers is a 24-bit read/write register. This register is
used in conjunction with its associated full-scale register to
form a register pair. The power-on reset value is automatically
overwritten if an internal or system zero-scale calibration is
initiated by the user. The AD7195 must be placed in powerdown mode or idle mode when writing to the offset register.
The full-scale register is a 24-bit register that holds the full-scale
calibration coefficient for the ADC. The AD7195 has four fullscale registers; therefore, each channel has a dedicated full-scale
register (see Table 25). The full-scale registers are read/write
registers. However, when writing to the full-scale registers, the
ADC must be placed in power-down mode or idle mode. These
registers are configured at power-on with factory-calibrated
full-scale calibration coefficients, the calibration being performed
at gain = 1. Therefore, every device has different default coefficients. The default value is automatically overwritten if an
internal or system full-scale calibration is initiated by the user
or if the full-scale register is written to.
Rev. 0 | Page 24 of 44
AD7195
ADC CIRCUIT INFORMATION
AVDD AGND DVDD DGND
REFIN(+) REFIN(–)
REFERENCE
DETECT
AIN1
AIN2
AIN3
AIN4
AVDD
MUX
PGA
AINCOM
SERIAL
INTERFACE
AND
CONTROL
LOGIC
Σ-Δ
ADC
DOUT/RDY
DIN
SCLK
CS
SYNC
BPDSW
AGND
AC
EXCITATION
CLOCK
AD7195
ACX1
ACX1
CLOCK
CIRCUITRY
ACX2
ACX2
MCLK1 MCLK2
08771-001
TEMP
SENSOR
Figure 18. Block Diagram
Σ-Δ ADC and Filter
OVERVIEW
The AD7195 is an ultralow noise ADC that incorporates a Σ-Δ
modulator, a buffer, PGA, and on-chip digital filtering intended
for the measurement of wide dynamic range signals, such as
those in pressure transducers, weigh scales, and strain gage
applications. Figure 18 shows the block diagram for the part.
Analog Inputs
The device can be configured to have two differential or four
pseudo differential analog inputs. The analog inputs can be
buffered or unbuffered.
Multiplexer
The AD7195 contains a fourth-order Σ-Δ modulator followed
by a digital filter. The device offers the following filter options:
•
•
•
•
Sinc4
Sinc3
Chop enabled/disabled
Zero latency
AC Excitation
The AD7195 supports ac excitation of load cells. It provides the
four logic outputs needed to control the transistors in an ac
excited load cell design.
The on-chip multiplexer increases the channel count of the
device. Because the multiplexer is included on chip, any
channel changes are synchronized with the conversion process.
Serial Interface
PGA
Clock
The analog input signal can be amplified using the PGA. The
PGA allows gains of 1, 8, 16, 32, 64, and 128.
The AD7195 has an internal 4.92 MHz clock. Either this clock
or an external clock can be used as the clock source to the
AD7195. The internal clock can also be made available on a
pin if a clock source is required for external circuitry.
Reference Detect
The AD7195 is capable of monitoring the external reference. If
the reference is not present, a flag is set in the status register of
the device.
Burnout Currents
Two 500 nA burnout currents are included on-chip to detect
the presence of the external sensor.
The AD7195 has a 4-wire SPI. The on-chip registers are
accessed via the serial interface.
Temperature Sensor
The on-chip temperature sensor monitors the die temperature.
Calibration
Both internal and system calibration are included on chip; thus,
the user has the option of removing offset/gain errors internal
to the AD7195 only, or removing the offset/gain errors of the
complete end system.
Rev. 0 | Page 25 of 44
AD7195
The AD7195 has two differential/four pseudo differential
analog input channels, which can be buffered or unbuffered. In
buffered mode (the BUF bit in the configuration register is set
to 1), the input channel feeds into a high impedance input stage
of the buffer amplifier. Therefore, the input can tolerate significant source impedances and is tailored for direct connection
to external resistive-type sensors such as strain gages or resistance temperature detectors (RTDs).
When BUF = 0, the part operates in unbuffered mode. This
results in a higher analog input current. Note that this unbuffered
input path provides a dynamic load to the driving source.
Therefore, resistor/capacitor combinations on the input pins
can cause gain errors, depending on the output impedance of
the source that is driving the ADC input. Table 27 shows the
allowable external resistance/capacitance values for unbuffered
mode at a gain of 1 such that no gain error at the 20-bit level is
introduced.
Table 27. External R-C Combination for No 20-Bit Gain Error
C (pF)
R (Ω)
50
1.4 k
100
850
500
300
1000
230
5000
30
The absolute input voltage range in buffered mode is restricted
to a range between AGND + 250 mV and AVDD − 250 mV. Care
must be taken in setting up the common-mode voltage so that
these limits are not exceeded. Otherwise, linearity and noise
performance degrades.
AD7195 is 0 to 3.75 V/gain in unipolar mode or ±3.75 V/gain
in bipolar mode.
REFERENCE
The ADC has a fully differential input capability for the reference channel. The common-mode range for these differential
inputs is from AGND to AVDD. The reference voltage REFIN
(REFIN(+) − REFIN(−)) is AVDD nominal, but the AD7195
is functional with reference voltages from 1 V to AVDD. In
applications where the excitation (voltage or current) for the
transducer on the analog input also drives the reference voltage
for the part, the effect of the low frequency noise in the excitation source is removed because the application is ratiometric. If
the AD7195 is used in a nonratiometric application, a low noise
reference should be used.
The reference input is unbuffered; therefore, excessive R-C
source impedances introduce gain errors. R-C values similar
to those in Table 27 are recommended for the reference inputs.
Deriving the reference input voltage across an external resistor
means that the reference input sees significant external source
impedance. External decoupling on the REFINx pins is not
recommended in this type of circuit configuration. Conversely,
if large decoupling capacitors are used on the reference inputs,
there should be no resistors in series with the reference inputs.
Recommended 2.5 V reference voltage sources for the AD7195
include the ADR421 and ADR431, which are low noise references.
These references tolerate decoupling capacitors on REFIN(+)
without introducing gain errors in the system. Figure 19 shows the
recommended connections between the ADR421 and the AD7195.
2
The absolute input voltage in unbuffered mode includes the
range between AGND − 50 mV and AVDD + 50 mV. The
negative absolute input voltage limit does allow the possibility
of monitoring small true bipolar signals with respect to AGND.
0.1µF
VIN
VOUT 6
10µF
REFINx(+)
4.7µF
4
PGA
AD7195
ADR421
AVDD
GND
TRIM 5
REFINx(–)
08771-037
ANALOG INPUT CHANNEL
Figure 19. ADR421 to AD7195 Connections
When the gain stage is enabled, the output from the buffer
is applied to the input of the PGA. The presence of the PGA
means that signals of small amplitude can be gained within the
AD7195 while still maintaining excellent noise performance.
For example, when the gain is set to 128, the rms noise is 8.5 nV,
typically, when the output data rate is 4.7 Hz, which is equivalent
to 23 bits of effective resolution or 20.5 bits of noise-free resolution.
The AD7195 can be programmed to have a gain of 1, 8, 16, 32,
64, and 128 using Bit G2 to Bit G0 in the configuration register.
Therefore, with an external 2.5 V reference, the unipolar ranges
are from 0 mV to 19.53 mV to 0 V to 2.5 V and the bipolar
ranges are from ±19.53 mV to ±2.5 V.
The analog input range must be limited to ±(AVDD − 1.25 V)/gain
because the PGA requires some headroom. Therefore, if AVDD =
5 V, the maximum analog input that can be applied to the
REFERENCE DETECT
The AD7195 includes on-chip circuitry to detect whether the
part has a valid reference for conversions or calibrations. This
feature is enabled when the REFDET bit in the configuration
register is set to 1. If the voltage between the REFIN(+) and
REFIN(−) pins is between 0.3 V and 0.6 V, the AD7195 detects
that it no longer has a valid reference. In this case, the NOREF
bit of the status register is set to 1. If the AD7195 is performing
normal conversions and the NOREF bit becomes active, the
conversion result is all 1s.
Therefore, it is not necessary to continuously monitor the status
of the NOREF bit when performing conversions. It is only
necessary to verify its status if the conversion result read from
the ADC data register is all 1s. If the AD7195 is performing
either an offset or full-scale calibration and the NOREF bit
becomes active, the updating of the respective calibration
Rev. 0 | Page 26 of 44
AD7195
registers is inhibited to avoid loading incorrect coefficients to
these registers, and the ERR bit in the status register is set. If
the user is concerned about verifying that a valid reference is
in place every time a calibration is performed, the status of the
ERR bit should be checked at the end of the calibration cycle.
turned on, they flow in the external transducer circuit, and a
measurement of the input voltage on the analog input channel
can be taken. It will take some time for the burnout currents to
detect an open circuit condition as the currents will need to
charge any external capacitors
BIPOLAR/UNIPOLAR CONFIGURATION
There are several reasons why a fault condition might be
detected. The front-end sensor may be open circuit. The frontend sensor may be overloaded, or the reference may be absent
and the NOREF bit in the status register is set, thus clamping
the data to all 1s. Check these possibilities first. If the voltage
measured is 0 V, it may indicate that the transducer has short
circuited. The current sources work over the normal absolute
input voltage range specifications when the analog inputs are
buffered and chop is disabled.
The analog input to the AD7195 can accept either unipolar or
bipolar input voltage ranges. A bipolar input range does not
imply that the part can tolerate negative voltages with respect
to system AGND. In pseudo differential mode, signals are
referenced to AINCOM while in differential mode, signals are
referenced to the negative input of the differential pair. For
example, if AINCOM is 2.5 V and the AD7195 AIN1 analog
input is configured for unipolar mode with a gain of 2, the input
voltage range on the AIN1 pin is 2.5 V to 3.75 V when a 2.5 V
reference is used. If AINCOM is 2.5 V and the AD7195 AIN1
analog input is configured for bipolar mode with a gain of 2, the
analog input range on AIN1 is 1.25 V to 3.75 V.
The bipolar/unipolar option is chosen by programming the U/B
bit in the configuration register.
DATA OUTPUT CODING
When the ADC is configured for unipolar operation, the output
code is natural (straight) binary with a zero differential input
voltage resulting in a code of 00...00, a midscale voltage resulting in a code of 100...000, and a full-scale input voltage resulting
in a code of 111...111. The output code for any analog input
voltage can be represented as
Code = (2N × AIN × Gain)/VREF
When the ADC is configured for bipolar operation, the output
code is offset binary with a negative full-scale voltage resulting
in a code of 000...000, a zero differential input voltage resulting
in a code of 100...000, and a positive full-scale input voltage
resulting in a code of 111...111. The output code for any analog
input voltage can be represented as
Code = 2N – 1 × [(AIN × Gain/VREF) + 1]
where:
N = 24.
AIN is the analog input voltage.
Gain is the PGA setting (1 to 128).
BURNOUT CURRENTS
The AD7195 contains two 500 nA constant current generators,
one sourcing current from AVDD to AIN(+) and one sinking
current from AIN(−) to AGND, where AIN(+) is the positive
analog input terminal and AIN(−) is the negative analog input
terminal in differential mode and AINCOM in pseudo differential mode. The currents are switched to the selected analog
input pair. Both currents are either on or off, depending on the
burnout current enable (BURN) bit in the configuration
register. These currents can be used to verify that an external
transducer remains operational before attempting to take
measurements on that channel. After the burnout currents are
AC EXCITATION
AC excitation of the bridge addresses many of the concerns
with thermocouple, offset, and drift effects encountered in
dc excited applications. In ac excitation, the polarity of the
excitation voltage to the bridge is reversed on alternate
cycles. The result is the elimination of dc errors at the
expense of a more complex system design. Figure 50 outlines
the connections for an ac excited bridge application based
on the AD7195.
The excitation voltage to the bridge must be switched on
alternate cycles. Transistor T1 to Transistor T4 in Figure 50
perform the switching of the excitation voltage. These transistors can be discrete matched bipolar or MOS transistors, or a
dedicated bridge driver chip, such as the MIC4427 available
from Micrel Components, can be used to perform the task.
Since the analog input voltage and the reference voltage are
reversed on alternate cycles, the AD7195 must be synchronized
with this reversing of the excitation voltage. To allow the
AD7195 to synchronize itself with this switching, it provides
the logic control signals for the switching of the excitation
voltage. These signals are the nonoverlapping CMOS outputs
ACX1/ACX1 and ACX2/ACX2.
One of the problems encountered with ac excitation is the
settling time associated with the analog input signals after
the excitation voltage is switched. This is particularly true in
applications where there are long lead lengths from the bridge
to the AD7195. It means that the converter could encounter
errors because it is processing signals that are not fully settled.
The AD7195 includes a delay between the switching of the ac
excitation signals and the processing of data at the analog
inputs. The delay equals 100 μs when FS[9:0] equals 1 and
equals 200 μs for all other output data rates.
The AD7195 also scales the ac excitation switching frequency
in accordance with the output data rate. This avoids situations
where the bridge is switched at an unnecessarily faster rate than
the system requires.
The fact that the AD7195 can handle reference voltages, which
are the same as the excitation voltages, is particularly useful
Rev. 0 | Page 27 of 44
AD7195
in ac excitation where resistor divider arrangements on the
reference input add to the settling time associated with the
switching.
When the ACX bit in the configuration register is set to 0,
the digital outputs ACX1 and ACX2 are high, while outputs
ACX2 and ACX1 are low. Therefore, the bridge is dc excited
with the T2 and T4 transistors turned on and the T1 and T3
transistors turned off. When the AD7195 is in power-down
mode, outputs ACX1 and ACX2 are low and outputs ACX1
and ACX2 are high so that the excitation voltage is disconnected from the bridge.
CHANNEL SEQUENCER
The AD7195 includes a channel sequencer, which simplifies
communications with the device in multichannel applications.
The sequencer also optimizes the channel throughput of the
device because the sequencer switches channels at the optimum
rate rather than waiting for instructions via the SPI interface.
When several channels are enabled, the ADC must allow the
complete settling time to generate a valid conversion each time
that the channel is changed. The AD7195 takes care of this:
when a channel is selected, the modulator and filter are reset,
and the RDY pin is taken high. The AD7195 then allows the
complete settling time to generate the first conversion. RDY
goes low only when a valid conversion is available. The AD7195
then selects the next enabled channel and converts on that
channel. The user can then read the data register while the
ADC is performing the conversion on the next channel.
The time required to read a valid conversion from all enabled
channels is equal to
tSETTLE × number of enabled channels
For example, if the sinc4 filter is selected, chop is disabled, and
zero latency is disabled, the settling time for each channel is
equal to
tSETTLE = 4/fADC
Bit CH0 to Bit CH7 in the configuration register are used to
enable the required channels. In continuous conversion mode,
the ADC selects each of the enabled channels in sequence and
performs a conversion on the channel. The RDY pin goes low
when a valid conversion is available on each channel. When
several channels are enabled, the contents of the status register
should be attached to the 24-bit word so that the user can
identify the channel that corresponds to each conversion. To
attach the status register value to the conversion, Bit DAT_STA
in the mode register should be set to 1.
where fADC is the output data rate when continuously converting
on a single channel. The time required to sample N channels is
DIGITAL INTERFACE
The DOUT/RDY pin functions as a data ready signal also; the
line goes low when a new data-word is available in the output
register. It is reset high when a read operation from the data
register is complete. It also goes high prior to the updating of the
data register to indicate when not to read from the device to
ensure that a data read is not attempted while the register is being
updated. CS is used to select a device. It can be used to decode the
AD7195 in systems where several components are connected to
the serial bus.
As indicated in the On-Chip Registers section, the programmable functions of the AD7195 are controlled using a set of
on-chip registers. Data is written to these registers via the serial
interface of the part. Read access to the on-chip registers is also
provided by this interface. All communication with the part must
start with a write to the communications register. After power-on
or reset, the device expects a write to its communications register.
The data written to this register determines whether the next operation is a read operation or a write operation and determines to
which register this read or write operation occurs. Therefore,
write access to any of the other registers on the part begins with
a write operation to the communications register, followed by a
write to the selected register. A read operation from any other
register (except when continuous read mode is selected) starts
with a write to the communications register, followed by a read
operation from the selected register.
The serial interface of the AD7195 consists of four signals: CS,
DIN, SCLK, and DOUT/RDY. The DIN line is used to transfer
data into the on-chip registers and DOUT/RDY is used for
accessing data from the on-chip registers. SCLK is the serial
clock input for the device, and all data transfers (either on DIN
or DOUT/RDY) occur with respect to the SCLK signal.
4/(fADC× N)
RDY
CHANNEL A
CHANNEL B
CHANNEL C
1/fADC
08771-028
CONVERSIONS
Figure 20. Channel Sequencer
Figure 3 and Figure 4 show timing diagrams for interfacing to the
AD7195, with CS being used to decode the part. Figure 3 shows
the timing for a read operation from the output shift register of
the AD7195, and Figure 4 shows the timing for a write operation
to the input shift register.
It is possible to read the same word from the data register several
times even though the DOUT/RDY line returns high after the
first read operation. However, care must be taken to ensure that
the read operations are completed before the next output update
occurs. In continuous read mode, the data register can be read
only once.
Rev. 0 | Page 28 of 44
AD7195
The serial interface can operate in 3-wire mode by tying CS low.
In this case, the SCLK, DIN, and DOUT/RDY lines are used to
communicate with the AD7195. The end of the conversion can
be monitored using the RDY bit or pin. This scheme is suitable
for interfacing to microcontrollers. If CS is required as a decoding
signal, it can be generated from a port pin. For microcontroller
interfaces, it is recommended that SCLK idle high between data
transfers.
The AD7195 can be operated with CS used as a frame synchronization signal. This scheme is useful for DSP interfaces. In this
case, the first bit (MSB) is effectively clocked out by CS because
CS normally occurs after the falling edge of SCLK in DSPs. The
SCLK can continue to run between data transfers, provided the
timing numbers are obeyed.
The serial interface can be reset by writing a series of 1s to the
DIN input. If a Logic 1 is written to the AD7195 DIN line for
at least 40 serial clock cycles, the serial interface is reset. This
ensures that the interface can be reset to a known state if the
interface gets lost due to a software error or some glitch in the
system. Reset returns the interface to the state in which it expects
a write to the communications register. This operation resets the
contents of all registers to their power-on values. Following a
reset, the user should allow a period of 500 μs before addressing
the serial interface.
The AD7195 can be configured to continuously convert or to
perform a single conversion (see Figure 21 through Figure 23).
Single Conversion Mode
In single conversion mode, the AD7195 is placed in powerdown mode after conversions. When a single conversion is
initiated by setting MD2, MD1, and MD0 to 0, 0, 1, respectively,
in the mode register, the AD7195 powers up, performs a single
conversion, and then returns to power-down mode. The onchip oscillator requires 1 ms, approximately, to power up.
DOUT/RDY goes low to indicate the completion of a conversion. When the data-word has been read from the data register,
DOUT/RDY goes high. If CS is low, DOUT/RDY remains high
until another conversion is initiated and completed. The data
register can be read several times, if required, even when
DOUT/RDY has gone high.
If several channels are enabled, the ADC sequences through the
enabled channels and performs a conversion on each channel.
When a conversion is started, DOUT/RDY goes high and
remains high until a valid conversion is available. As soon as
the conversion is available, DOUT/RDY goes low. The ADC
then selects the next channel and begins a conversion. The user
can read the present conversion while the next conversion is
being performed. As soon as the next conversion is complete,
the data register is updated; therefore, the user has a limited
period in which to read the conversion. When the ADC has
performed a single conversion on each of the selected channels,
it returns to power-down mode.
If the DAT_STA bit in the mode register is set to 1, the contents
of the status register are output along with the conversion each
time that the data read is performed. The four LSBs of the status
register indicate the channel to which the conversion corresponds.
CS
0x08
0x280060
0x58
DIN
DATA
08771-029
DOUT/RDY
SCLK
Figure 21. Single Conversion
Rev. 0 | Page 29 of 44
AD7195
Continuous Conversion Mode
Continuous conversion is the default power-up mode. The
AD7195 converts continuously, and the RDY bit in the status
register goes low each time a conversion is complete. If CS is
low, the DOUT/RDY line also goes low when a conversion
is completed. To read a conversion, the user writes to the
communications register, indicating that the next operation is
a read of the data register. When the data-word has been read
from the data register, DOUT/RDY goes high. The user can
read this register additional times, if required. However, the
user must ensure that the data register is not being accessed at
the completion of the next conversion or else the new conversion
word is lost.
When several channels are enabled, the ADC continuously
loops through the enabled channels, performing one conversion
on each channel per loop. The data register is updated as soon
as each conversion is available. The DOUT/RDY pin pulses low
each time a conversion is available. The user can then read the
conversion while the ADC converts on the next enabled channel.
If the DAT_STA bit in the mode register is set to 1, the contents
of the status register are output along with the conversion each
time that the data read is performed. The status register
indicates the channel to which the conversion corresponds.
CS
0x58
0x58
DIN
DATA
DATA
08771-030
DOUT/RDY
SCLK
Figure 22. Continuous Conversion
Rev. 0 | Page 30 of 44
AD7195
Continuous Read
conversion is complete, and the new conversion is placed in
the output serial register.
Rather than write to the communications register each time
a conversion is complete to access the data, the AD7195 can
be configured so that the conversions are placed on the
DOUT/RDY line automatically. By writing 01011100 to
the communications register, the user need only apply the
appropriate number of SCLK cycles to the ADC, and the
conversion word is automatically placed on the DOUT/RDY
line when a conversion is complete. The ADC should be
configured for continuous conversion mode.
To exit the continuous read mode, Instruction 01011000 must
be written to the communications register while the RDY pin
is low. While in continuous read mode, the ADC monitors
activity on the DIN line so that it can receive the instruction
to exit the continuous read mode. Additionally, a reset occurs
if 40 consecutive 1s are seen on DIN. Therefore, DIN should
be held low in continuous read mode until an instruction is to
be written to the device.
When several channels are enabled, the ADC continuously
steps through the enabled channels and performs one conversion on each channel each time that it is selected. DOUT/
RDY pulses low when a conversion is available. When the user
applies sufficient SCLK pulses, the data is automatically placed
on the DOUT/RDY pin. If the DAT_STA bit in the mode
register is set to 1, the contents of the status register are output
along with the conversion. The status register indicates the
channel to which the conversion corresponds.
When DOUT/RDY goes low to indicate the end of a conversion,
sufficient SCLK cycles must be applied to the ADC; the data
conversion is then placed on the DOUT/RDY line. When the
conversion is read, DOUT/RDY returns high until the next
conversion is available. In this mode, the data can be read only
once. Also, the user must ensure that the data-word is read
before the next conversion is complete. If the user has not read
the conversion before the completion of the next conversion,
or if insufficient serial clocks are applied to the AD7195 to
read the word, the serial output register is reset when the next
CS
0x5C
DIN
DATA
DATA
DATA
08771-031
DOUT/RDY
SCLK
Figure 23. Continuous Read
Rev. 0 | Page 31 of 44
AD7195
RESET
The circuitry and serial interface of the AD7195 can be reset
by writing consecutive 1s to the device; 40 consecutive 1s are
required to perform the reset. This resets the logic, the digital
filter, and the analog modulator, whereas all on-chip registers
are reset to their default values. A reset is automatically
performed on power-up. When a reset is initiated, the user
must allow a period of 500 μs before accessing any of the
on-chip registers. A reset is useful if the serial interface loses
synchronization due to noise on the SCLK line.
SYSTEM SYNCHRONIZATION
The SYNC input allows the user to reset the modulator and the
digital filter without affecting any of the setup conditions on
the part. This allows the user to start gathering samples of the
analog input from a known point in time, that is, the rising edge
of SYNC. SYNC needs to be taken low for at least four master
clock cycles to implement the synchronization function.
If multiple AD7195 devices operate from a common master
clock, they can be synchronized so that their data registers are
updated simultaneously. A falling edge on the SYNC pin resets
the digital filter and the analog modulator and places the AD7195
into a consistent, known state. While the SYNC pin is low, the
AD7195 is maintained in this state. On the SYNC rising edge,
the modulator and filter are taken out of this reset state and, on
the next clock edge, the part starts to gather input samples again.
In a system using multiple AD7195 devices, a common signal to
their SYNC pins synchronizes their operation. This is normally
done after each AD7195 has performed its own calibration or
has calibration coefficients loaded into its calibration registers.
The conversions from the AD7195s are then synchronized.
The part is taken out of reset on the master clock falling edge
following the SYNC low to high transition. Therefore, when
multiple devices are being synchronized, the SYNC pin should
be taken high on the master clock rising edge to ensure that all
devices begin sampling on the master clock falling edge. If the
SYNC pin is not taken high in sufficient time, a difference of
one master clock cycle may result between the devices; that is,
the instant at which conversions are available differs from part
to part by a maximum of one master clock cycle.
The SYNC pin can also be used as a start conversion command.
In this mode, the rising edge of SYNC starts conversion, and the
falling edge of RDY indicates when the conversion is complete.
The settling time of the filter has to be allowed for each data
register update. For example, if the ADC is configured to use
the sinc4 filter, zero latency is disabled, and chop is disabled, the
settling time equals 4/fADC where fADC is the output data rate
when continuously converting on a single channel.
CLOCK
The AD7195 includes an internal 4.92 MHz clock on-chip. This
internal clock has a tolerance of ±4%. Either the internal clock
or an external crystal/clock can be used as the clock source to
the AD7195. The clock source is selected using the CLK1 and
CLK0 bits in the mode register. When an external crystal is
used, it must be connected across the MCLK1 and MCLK2
pins. The crystal manufacturer recommends the load capacitances
required for the crystal. The MCLK1 and MCLK2 pins of the
AD7195 have a capacitance of 15 pF, typically. If an external
clock source is used, the clock source must be connected to the
MCLK2 pin, and the MCLK1 pin can be left floating.
The internal clock can also be made available at the MCLK2
pin. This is useful when several ADCs are used in an application
and the devices must be synchronized. The internal clock from
one device can be used as the clock source for all ADCs in the
system. Using a common clock, the devices can be synchronized by applying a common reset to all devices, or the SYNC
pin can be pulsed.
ENABLE PARITY
The AD7195 also has an on-chip parity check function that
detects 1-bit errors in the serial communications between
the ADC and the microprocessor. When the ENPAR bit in
the mode register is set to 1, parity is enabled. The contents of
the status register must be transmitted along with each 24-bit
conversion when the parity function is enabled. To append the
contents of the status register to each conversion read, the
DAT_STA bit in the mode register should be set to 1.
For each conversion read, the parity bit in the status register is
programmed so that the overall number of 1s transmitted in the
24-bit data-word is even. Therefore, for example, if the 24-bit
conversion contains eleven 1s (binary format), the parity bit is
set to 1 so that the total number of 1s in the serial transmission
is even. If the microprocessor receives an odd number of 1s, it
knows that the data received has been corrupted.
The parity function only detects 1-bit errors. For example, two
bits of corrupt data can result in the microprocessor receiving an
even number of 1s. Therefore, an error condition is not detected.
TEMPERATURE SENSOR
Embedded in the AD7195 is a temperature sensor. This is
selected using the CH2 bit in the configuration register. When
the CH2 bit is set to 1, the temperature sensor is enabled. When
the temperature sensor is selected and bipolar mode is selected,
the device should return a code of 0x800000 when the temperature is 0 K. A one-point calibration is needed to get the optimum
performance from the sensor. Therefore, a conversion at 25°C
should be recorded and the sensitivity calculated. The sensitivity
is approximately 2815 codes/°C. The equation for the temperature
sensor is
Temp (K) = (Conversion − 0x800000)/2815 K
Temp (°C) = Temp (K) − 273
Following the one point calibration, the internal temperature
sensor has an accuracy of ±2 °C, typically.
Rev. 0 | Page 32 of 44
AD7195
BRIDGE POWER-DOWN SWITCH
In bridge applications, such as strain gauges and load cells, the
bridge itself consumes the majority of the current in the system.
For example, a 350 Ω load cell requires 15 mA of current when
excited with a 5 V supply. To minimize the current consumption
of the system, the bridge can be disconnected (when it is not
being used) using the bridge power-down switch. Figure 50
shows how the bridge power-down switch is used. The switch
can withstand 30 mA of continuous current, and it has an on
resistance of 10 Ω maximum.
CALIBRATION
The AD7195 provides four calibration modes that can be programmed via the mode bits in the mode register. These modes
are internal zero-scale calibration, internal full-scale calibration,
system zero-scale calibration, and system full-scale calibration.
A calibration can be performed at any time by setting the MD2
to MD0 bits in the mode register appropriately. A calibration
should be performed when the gain is changed. After each
conversion, the ADC conversion result is scaled using the ADC
calibration registers before being written to the data register.
The offset calibration coefficient is subtracted from the result
prior to multiplication by the full-scale coefficient.
To start a calibration, write the relevant value to the MD2 to
MD0 bits. The DOUT/RDY pin and the RDY bit in the status
register go high when the calibration is initiated. When the
calibration is complete, the contents of the corresponding
calibration registers are updated, the RDY bit in the status
register is reset, the DOUT/ RDY pin returns low (if CS is
low), and the AD7195 reverts to idle mode.
During an internal zero-scale or full-scale calibration, the respective zero input and full-scale input are automatically connected
internally to the ADC input pins. A system calibration, however,
expects the system zero-scale and system full-scale voltages to
be applied to the ADC pins before initiating the calibration
mode. In this way, errors external to the ADC are removed.
From an operational point of view, treat a calibration like
another ADC conversion. A zero-scale calibration, if required,
must always be performed before a full-scale calibration. Set the
system software to monitor the RDY bit in the status register or
the DOUT/RDY pin to determine the end of calibration via a
polling sequence or an interrupt-driven routine.
With chop disabled, both an internal zero-scale calibration and a
system zero-scale calibration require a time equal to the settling
time, tSETTLE, (4/fADC for the sinc4 filter and 3/fADC for the sinc3 filter).
With chop enabled, an internal zero-scale calibration is not
needed because the ADC itself minimizes the offset continuously.
However, if an internal zero-scale calibration is performed, the
settling time, tSETTLE, (2/fADC) is required to perform the calibration. Similarly, a system zero-scale calibration requires a time of
tSETTLE to complete.
To perform an internal full-scale calibration, a full-scale input
voltage is automatically connected to the selected analog input
for this calibration. For a gain of 1, the time required for an
internal full-scale calibration is equal to tSETTLE. For higher gains,
the internal full-scale calibration requires a time of 2 × tSETTLE.
A full-scale calibration is recommended each time the gain of a
channel is changed to minimize the full-scale error.
A system full-scale calibration requires a time of tSETTLE. With
chop disabled, the zero-scale calibration (internal or system
zero-scale) should be performed before the system full-scale
calibration is initiated.
An internal zero-scale calibration, system zero-scale calibration
and system full-scale calibration can be performed at any output
data rate. An internal full-scale calibration can be performed at
any output data rate for which the filter word FS[9:0] is divisible
by 16, FS[9:0] being the decimal equivalent of the 10-bit word
written to Bit FS9 to Bit FS0 in the mode register. Therefore,
internal full-scale calibrations can be performed at output data
rates such as 10 Hz or 50 Hz when chop is disabled. Using these
lower output data rates results in better calibration accuracy.
The offset error is, typically, 100 μV/gain. If the gain is changed,
it is advisable to perform a calibration. A zero-scale calibration
(an internal zero-scale calibration or system zero-scale
calibration) reduces the offset error to the order of the noise.
The gain error of the AD7195 is factory calibrated at a gain of 1
with a 5 V power supply at ambient temperature. Following this
calibration, the gain error is 0.001%, typically, at 5 V. Table 28
shows the typical uncalibrated gain error for the different gain
settings. An internal full-scale calibration reduces the gain error
to 0.001%, typically, when the gain is equal to 1. For higher
gains, the gain error post internal full-scale calibration is
0.0075%, typically. A system full-sale calibration reduces the
gain error to the order of the noise.
Table 28. Typical Precalibration Gain Error vs. Gain
Gain
8
16
32
64
128
Precalibration Gain Error (%)
−0.11
−0.20
−0.23
−0.29
−0.39
The AD7195 gives the user access to the on-chip calibration
registers, allowing the microprocessor to read the calibration
coefficients of the device and also to write its own calibration
coefficients from prestored values in the EEPROM. A read of
the registers can be performed at any time. However, the ADC
must be placed in power-down or idle mode when writing to
the registers. The values in the calibration registers are 24-bits
wide. The span and offset of the part can also be manipulated
using the registers.
Rev. 0 | Page 33 of 44
AD7195
DIGITAL FILTER
The AD7195 offers a lot of flexibility in the digital filter. The
device has four filter options. The device can be operated
with a sinc3 or sinc4 filter, chop can be enabled or disabled, and
zero latency can be enabled. The option selected affects the
output data rate, settling time, and 50 Hz/60 Hz rejection. The
following sections describe each filter type, indicating the
available output data rates for each filter option. The filter response along with the settling time and 50 Hz/60 Hz rejection
is also discussed.
When conversions are performed on a single channel and a
step change occurs, the ADC does not detect the change in
analog input. Therefore, it continues to output conversions
at the programmed output data rate. However, it is at least four
conversions later before the output data accurately reflect the
analog input. If the step change occurs while the ADC is
processing a conversion, then the ADC takes five conversions
after the step change to generate a fully settled result.
ANALOG
INPUT
FULLY
SETTLED
When the AD7195 is powered up, the sinc4 filter is selected
by default and chop is disabled. This filter gives excellent noise
performance over the complete range of output data rates. It
also gives the best 50 Hz/60 Hz rejection, but it has a long
settling time.
1/fADC
Figure 26. Asynchronous Step Change in Analog Input
The 3 dB frequency for the sinc4 filter is equal to
f3dB = 0.23 × fADC
ADC
Table 29 gives some examples of the relationship between the
values in Bits FS[9:0] and the corresponding output data rate
and settling time.
SINC3/SINC4
MODULATOR
Table 29. Examples of Output Data Rates and the
Corresponding Settling Time
08771-033
CHOP
Figure 24. Sinc4 Filter (Chop Disabled)
4
Sinc Output Data Rate/Settling Time
The output data rate (the rate at which conversions are available
on a single channel when the ADC is continuously converting)
is equal to
fADC = fCLK/(1024 × FS[9:0])
The settling time for the sinc filter is equal to
tSETTLE = 4/fADC
When a channel change occurs, the modulator and filter are
reset. The settling time is allowed to generate the first conversion after the channel change. Subsequent conversions on this
channel occur at 1/fADC.
Sinc4 Zero Latency
where:
fADC is the output data rate.
fCLK is the master clock (4.92 MHz nominal).
FS[9:0] is the decimal equivalent of Bit FS9 to Bit FS0 in the
mode register.
CHANNEL B
CH A CH A
CH B CH B
1/fADC
CH B
08771-038
CH A
Settling Time (ms)
400
80
66.6
fADC = 1/tSETTLE = fCLK/(4 × 1024 × FS[9:0])
4
CONVERSIONS
Output Data Rate (Hz)
10
50
60
The output data rate equals
The output data rate can be programmed from 4.7 Hz to
4800 Hz; that is, FS[9:0] can have a value from 1 to 1023.
CHANNEL A
FS[9:0]
480
96
80
Zero latency is enabled by setting the single bit (Bit 11) in the
mode register to 1. With zero latency, the complete settling time
is allowed for each conversion. Therefore, the conversion time
when converting on a single channel or when converting on
several channels is constant. The user does not need to consider
the effects of channel changes on the output data rate.
where:
fADC is the output data rate.
fCLK is the master clock (4.92 MHz nominal).
FS[9:0] is the decimal equivalent of Bit FS9 to Bit FS0 in the
mode register.
CHANNEL
08771-039
ADC
OUTPUT
SINC4 FILTER (CHOP DISABLED)
4
Figure 25. Sinc Channel Change
Rev. 0 | Page 34 of 44
AD7195
When the analog input is constant or a channel change occurs,
valid conversions are available at a constant output data rate.
When conversions are being performed on a single channel and
a step change occurs on the analog input, the ADC continues to
output fully settled conversions if the step change is synchronized
with the conversion process. If the step change is asynchronous,
one conversion is output from the ADC, which is not completely
settled (see Figure 27).
Figure 29 shows the frequency response when FS[9:0] is
programmed to 80 and the master clock is equal to 4.92 MHz.
The output data rate is 60 Hz when zero latency is disabled and
15 Hz when zero latency is enabled. The sinc4 filter provides
60 Hz (±1 Hz) rejection of 120 dB minimum, assuming a stable
master clock.
0
–10
–20
ANALOG
INPUT
08771-040
ADC
OUTPUT
1/fADC
FILTER GAIN (dB)
–30
FULLY
SETTLED
Figure 27. Sinc4 Zero Latency Operation
–40
–50
–60
–70
–80
–90
–100
Table 30 shows examples of output data rate and the corresponding FS values.
0
Table 30. Examples of Output Data Rates and the
Corresponding Settling Time (Zero Latency)
Settling Time (ms)
400
80
66.6
Sinc4 50 Hz/60 Hz Rejection
Figure 28 shows the frequency response of the sinc4 filter when
FS[9:0] is set to 96 and the master clock is 4.92 MHz. With zero
latency disabled, the output data rate is equal to 50 Hz. With
zero latency enabled, the output data rate is 12.5 Hz. The sinc4
filter provides 50 Hz (±1 Hz) rejection in excess of 120 dB
minimum, assuming a stable master clock.
0
–10
–20
–30
120
150
Figure 29. Sinc4 Filter Response (FS[9:0] = 80)
Simultaneous 50 Hz and 60 Hz rejection is obtained when
FS[9:0] is programmed to 480 and the master clock equals
4.92 MHz. The output data rate is 10 Hz when zero latency is
disabled and 2.5 Hz when zero latency is enabled. The sinc4
filter provides 50 Hz (±1 Hz) and 60 Hz (±1 Hz) rejection of
120 dB minimum, assuming a stable master clock.
0
–10
–20
–30
–40
–50
–60
–70
–80
–40
–90
–50
–100
–60
–110
–70
–120
0
–80
30
60
90
120
FREQUENCY (Hz)
–90
150
Figure 30. Sinc4 Filter Response (FS[9:0] = 480)
–100
–110
–120
0
25
50
75
100
125
FREQUENCY (Hz)
150
08771-041
FILTER GAIN (dB)
90
08771-043
Output Data Rate (Hz)
2.5
12.5
15
60
FREQUENCY (Hz)
FILTER GAIN (dB)
FS[9:0]
480
96
80
30
08771-042
–110
–120
Simultaneous 50 Hz/60 Hz rejection can also be achieved using
the REJ60 bit in the mode register. When FS[9:0] is set to 96
and REJ60 is set to 1, notches are placed at 50 Hz and 60 Hz.
Figure 28. Sinc4 Filter Response (FS[9:0] = 96)
Rev. 0 | Page 35 of 44
AD7195
The output data rate is 50 Hz when zero latency is disabled and
12.5 Hz when zero latency is enabled. Figure 31 shows the
frequency response of the sinc4 filter. The filter provides 50 Hz
±1 Hz and 60 Hz ± 1 Hz rejection of 82 dB minimum, assuming
a stable 4.92 MHz master clock.
0
f3dB = 0.272 × fADC
Table 31 gives some examples of FS settings and the corresponding output data rates and settling times.
Table 31. Examples of Output Data Rates and the
Corresponding Settling Time
–10
–20
FS[9:0]
480
96
80
–30
FILTER GAIN (dB)
The 3 dB frequency is equal to
–40
–50
–60
Output Data Rate (Hz)
10
50
60
Settling Time (ms)
300
60
50
When a channel change occurs, the modulator and filter reset.
The complete settling time is allowed to generate the first
conversion after the channel change (see Figure 33). Subsequent
conversions on this channel are available at 1/fADC.
–70
–80
–90
–100
–110
CHANNEL
0
25
50
75
100
125
08771-044
–120
150
FREQUENCY (Hz)
CONVERSIONS
CHANNEL B
CHANNEL A
CH A
CH A CH A
CH B CH B CH B
CH B
08771-045
4
Figure 31. Sinc Filter Response (FS[9:0] = 96, REJ60 = 1)
1/fADC
3
SINC FILTER (CHOP DISABLED)
Figure 33. Sinc3 Channel Change
A sinc3 filter can be used instead of the sinc4 filter. The filter is
selected using the SINC3 bit in the mode register. The sinc3
filter is selected when the SINC3 bit is set to 1.
This filter has good noise performance when operating with
output data rates up to 1 kHz. It has moderate settling time and
moderate 50 Hz/60 Hz (±1 Hz) rejection.
ADC
When conversions are performed on a single channel and a step
change occurs, the ADC does not detect the change in analog
input. Therefore, it continues to output conversions at the programmed output data rate. However, it is at least three conversions later
before the output data accurately reflects the analog input. If the
step change occurs while the ADC is processing a conversion, the
ADC takes four conversions after the step change to generate a fully
settled result.
ANALOG
INPUT
SINC3/SINC4
FULLY
SETTLED
ADC
OUTPUT
Figure 32. Sinc3 Filter (Chop Disabled)
1/fADC
Sinc3 Output Data Rate and Settling Time
Figure 34. Asynchronous Step Change in Analog Input
The output data rate (the rate at which conversions are available
on a single channel when the ADC is continuously converting)
is equal to
fADC = fCLK/(1024 × FS[9:0])
where:
fADC is the output data rate.
fCLK is the master clock (4.92 MHz nominal).
FS[9:0] is the decimal equivalent of Bit FS9 to Bit FS0 in the
mode register.
08771-046
MODULATOR
08771-034
CHOP
Sinc3 Zero Latency
Zero latency is enabled by setting the single bit (Bit 11) in the
mode register to 1. With zero latency, the complete settling time
is allowed for each conversion. Therefore, the conversion time
when converting on a single channel or when converting on
several channels is constant. The user does not need to consider
the effects of channel changes on the output data rate.
The output data rate can be programmed from 4.7 Hz to
4800 Hz; that is, FS[9:0] can have a value from 1 to 1023.
The settling time is equal to
tSETTLE = 3/fADC
Rev. 0 | Page 36 of 44
AD7195
Sinc3 50 Hz/60 Hz Rejection
The output data rate equals
Figure 36 show the frequency response of the sinc3 filter when
FS[9:0] is set to 96 and the master clock equals 4.92 MHz. The
output data rate is equal to 50 Hz when zero latency is disabled
and 16.7 Hz when zero latency is enabled. The sinc3 filter gives
50 Hz ± 1 Hz rejection of 95 dB minimum for a stable master clock.
fADC = 1/tSETTLE = fCLK/(3 × 1024 × FS[9:0])
where:
fADC is the output data rate.
fCLK is the master clock (4.92 MHz nominal).
FS[9:0] is the decimal equivalent of Bit FS9 to Bit FS0 in the
mode register.
0
–10
–20
–30
FILTER GAIN (dB)
When the analog input is constant or a channel change occurs,
valid conversions are available at a constant output data rate.
When conversions are being performed on a single channel and
a step change occurs on the analog input, the ADC continues to
output fully settled conversions if the step change is synchronized
with the conversion process. If the step change is asynchronous,
one conversion is output from the ADC that is not completely
settled (see Figure 35).
–40
–50
–60
–70
–80
–90
–100
ANALOG
INPUT
–110
FULLY
SETTLED
ADC
OUTPUT
0
25
50
75
100
125
150
FREQUENCY (Hz)
Figure 36. Sinc3 Filter Response (FS[9:0] = 96)
08771-047
3
Figure 35. Sinc Zero Latency Operation
Table 32 provides examples of output data rates and the corresponding FS values.
Table 32. Examples of Output Data Rates and the
Corresponding Settling Time (Zero Latency)
Output Data Rate (Hz)
3.3
16.7
20
0
Settling Time (ms)
300
60
50
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
–110
–120
0
30
60
90
120
FREQUENCY (Hz)
Figure 37. Sinc3 Filter Response (FS[9:0] = 80)
Rev. 0 | Page 37 of 44
150
08771-049
FS[9:0]
480
96
80
When FS[9:0] is set to 80 and the master clock equals
4.92 MHz, 60 Hz rejection is achieved (see Figure 37). The
output data rate is equal to 60 Hz when zero latency is disabled
and 20 Hz when zero latency is enabled. The sinc3 filter has
rejection of 95 dB minimum at 60 Hz ± 1 Hz, assuming a stable
master clock.
FILTER GAIN (dB)
1/fADC
08771-048
–120
AD7195
Simultaneous 50 Hz and 60 Hz rejection is obtained when
FS[9:0] is set to 480 (master clock = 4.92 MHz), as shown in
Figure 38. The output data rate is 10 Hz when zero latency is
disabled and 3.3 Hz when zero latency is enabled. The sinc3
filter has rejection of 100 dB minimum at 50 Hz ± 1 Hz and
60 Hz ± 1 Hz.
0
–10
–20
FILTER GAIN (dB)
–30
–40
CHOP ENABLED (SINC4 FILTER)
With chop enabled, the ADC offset and offset drift are minimized.
The analog input pins are continuously swapped. With the
analog input pins connected in one direction, the settling time
of the sinc filter is allowed and a conversion is recorded. The
analog input pins are then inverted, and another settled conversion is obtained. Subsequent conversions are averaged to
minimize the offset. This continuous swapping of the analog
input pins and the averaging of subsequent conversions means
that the offset drift is also minimized. With chop enabled, the
resolution increases by 0.5 bits.
ADC
–50
–60
–70
CHOP
–80
SINC3/SINC4
MODULATOR
08771-035
–90
–100
–110
0
30
60
90
120
150
FREQUENCY (Hz)
08771-050
Figure 40. Chop Enabled
–120
Figure 38. Sinc3 Filter Response (FS[9:0] = 480)
Output Data Rate and Settling Time (Sinc4 Chop
Enabled)
For the sinc4 filter, the output data rate is equal to
Simultaneous 50 Hz/60 Hz rejection is also achieved using the
REJ60 bit in the mode register. When FS[9:0] is programmed to
96 and the REJ60 bit is set to 1, notches are placed at both 50 Hz
and 60 Hz for a stable 4.92 MHz master clock. Figure 39 shows
the frequency response of the sinc3 filter with this configuration.
Assuming a stable clock, the rejection at 50 Hz/60 Hz (±1 Hz)
is in excess of 67 dB minimum.
fADC = fCLK/(4 × 1024 × FS[9:0])
where:
fADC is the output data rate.
fCLK is the master clock (4.92 MHz nominal).
FS[9:0] is the decimal equivalent of Bit FS9 to Bit FS0 in the
mode register.
The value of FS[9:0] can be varied from 1 to 1023. This results
in an output data rate of 1.17 Hz to 1200 Hz. The settling time is
equal to
0
–10
–20
tSETTLE = 2/fADC
–40
Table 33 gives some examples of FS[9:0] values and the corresponding output data rates and settling times.
–50
–60
–70
Table 33. Examples of Output Data Rates and the
Corresponding Settling Time
–80
–90
FS[9:0]
96
80
–100
–110
–120
0
25
50
75
100
125
FREQUENCY (Hz)
150
08771-051
FILTER GAIN (dB)
–30
Figure 39. Sinc3 Filter Response (FS[9:0] = 96, REJ60 = 1)
Rev. 0 | Page 38 of 44
Output Data Rate (Hz)
12.5
15
Settling Time (ms)
160
133
AD7195
CH A CH A
CH B CH B CH B CH B
CH B
1/fADC
Figure 41. Channel Change (Sinc4 Chop Enabled)
–30
–40
–50
–60
–70
–80
–90
–100
When conversions are performed on a single channel and a
step change occurs, the ADC does not detect the change in
analog input; therefore, it continues to output conversions at
the programmed output data rate. However, it is at least two
conversions later before the output data accurately reflects the
analog input. If the step change occurs while the ADC is
processing a conversion, the ADC takes three conversions after
the step change to generate a fully settled result.
ANALOG
INPUT
–110
–120
0
25
50
75
100
125
08771-054
CH A
–20
150
FREQUENCY (Hz)
Figure 43. Sinc4 Filter Response (FS[9:0] = 96, Chop Enabled)
The 50 Hz/60 Hz rejection can be improved by setting the
REJ60 bit in the mode register to 1. With FS[9:0] set to 96
and REJ60 set to 1, the filter response shown Figure 44
is achieved. The output data rate is unchanged but the 50 Hz/
60 Hz (± 1 Hz) rejection is increased to 83 dB typically.
0
FULLY
SETTLED
–10
ADC
OUTPUT
–20
4
Figure 42. Asynchronous Step Change in Analog Input (Sinc Chop Enabled)
The cutoff frequency f3dB is equal to
f3dB = 0.24 × fADC
FILTER GAIN (dB)
–30
08771-053
1/fADC
–40
–50
–60
–70
–80
–90
4
50 Hz/60 Hz Rejection (Sinc Chop Enabled)
When FS[9:0] is set to 96 and chopping is enabled, the output
data rate is equal to 12.5 Hz for a 4.92 MHz master clock. The
filter response shown in Figure 43 is obtained. The chopping
introduces notches at odd integer multiples of fADC/2. The
notches due to the sinc filter in addition to the notches introduced by the chopping mean that simultaneous 50 Hz and
60 Hz rejection is achieved for an output data rate of 12.5 Hz.
The rejection at 50 Hz/60 Hz ± 1 Hz is typically 63 dB,
assuming a stable master clock.
–100
–110
–120
0
25
50
75
100
FREQUENCY (Hz)
125
150
08771-055
CONVERSIONS
CHANNEL B
08771-052
CHANNEL
CHANNEL A
0
–10
FILTER GAIN (dB)
When a channel change occurs, the modulator and filter reset.
The complete settling time is required to generate the first
conversion after the channel change. Subsequent conversions
on this channel occur at 1/fADC.
Figure 44. Sinc4 Filter Response (FS[9:0] = 96, Chop Enabled, REJ60 = 1)
Rev. 0 | Page 39 of 44
AD7195
With chop enabled, the ADC offset and offset drift are
minimized. The analog input pins are continuously swapped.
With the analog input pins connected in one direction, the
settling time of the sinc filter is allowed and a conversion is
recorded. The analog input pins invert and another settled
conversion is obtained. Subsequent conversions are averaged
to minimize the offset. This continuous swapping of the analog
input pins and the averaging of subsequent conversions means
that the offset drift is also minimized. With chop enabled, the
resolution increases by 0.5 bits. Using the sinc3 filter with chop
enabled is suitable for output data rates up to 320 Hz.
If conversions are performed on a single channel and a step
change occurs, the ADC does not detect the change in analog
input; therefore, it continues to output conversions at the
programmed output data rate. However, it is at least two
conversions later before the output data accurately reflects
the analog input. If the step change occurs while the ADC is
processing a conversion, then the ADC takes three conversions
after the step change to generate a fully settled result.
ANALOG
INPUT
FULLY
SETTLED
ADC
OUTPUT
08771-057
CHOP ENABLED (SINC3 FILTER)
ADC
1/fADC
Figure 47. Asynchronous Step Change in Analog Input (Sinc3 Chop Enabled)
The cutoff frequency f3dB is equal to
SINC3/SINC4
f3dB = 0.24 × fADC
50 Hz/60 Hz Rejection (Sinc3 Chop Enabled)
Figure 45. Chop Enabled (Sinc3 Chop Enabled)
When FS[9:0] is set to 96 and chopping is enabled, the filter
response shown in Figure 48 is obtained. The output data rate
is equal to 16.7 Hz for a 4.92 MHz master clock. The chopping
introduces notches at odd integer multiples of fADC/2. The
notches due to the sinc filter in addtion to the notches introduced by the chopping means that simultaneous 50 Hz and
60 Hz rejection is achieved for an output data rate of 16.7 Hz.
The rejection at 50 Hz/60 Hz ± 1 Hz is typically 53 dB,
assuming a stable master clock.
Output Data Rate and Settling Time (Sinc3 Chop
Enabled)
For the sinc3 filter, the output data rate is equal to
fADC = fCLK/(3 × 1024 × FS[9:0])
where:
fADC is the output data rate.
fCLK is the master clock (4.92 MHz nominal).
FS[9:0] is the decimal equivalent of Bit FS9 to Bit FS0 in the
mode register.
0
–10
The value of FS[9:0] can be varied from 1 to 1023. This results
in an output data rate of 1.56 Hz to 1600 Hz. The settling time
is equal to
tSETTLE = 2/fADC
Table 34. Examples of Output Data Rates and the
Corresponding Settling Time (Chop Enabled, Sinc3 Filter)
Output Data Rate (Hz)
16.7
20
–30
–40
–50
–60
–70
–80
–90
Settling Time (ms)
120
100
–100
–110
–120
When a channel change occurs, the modulator and filter are
reset. The complete settling time is required to generate the first
conversion after the channel change. Subsequent conversions on
this channel occur at 1/fADC.
CONVERSIONS
CHANNEL A
CH A
CH A CH A
CHANNEL B
CH B CH B CH B CH B
1/fADC
CH B
08771-056
CHANNEL
Figure 46. Channel Change (Sinc3 Chop Enable)
Rev. 0 | Page 40 of 44
0
25
50
75
100
125
150
FREQUENCY (Hz)
Figure 48. Sinc3 Filter Response (FS[9:0] = 96, Chop Enabled)
08771-058
FS[9:0]
96
80
–20
FILTER GAIN (dB)
MODULATOR
08771-036
CHOP
AD7195
The 50 Hz/60 Hz rejection can be improved by setting the
REJ60 bit in the mode register to 1. With FS[9:0] set to 96 and
REJ60 set to 1, the filter response shown in Figure 49 is achieved.
The output data rate is unchanged, but the 50 Hz/60 Hz ± 1 Hz
rejection improves to 73 dB typically.
0
–10
–20
SUMMARY OF FILTER OPTIONS
The AD7195 has several filter options. The filter that is chosen
affects the output data rate, settling time, the rms noise, the stop
band attenuation, and the 50 Hz/60 Hz rejection.
Table 35 shows some sample configurations and the corresponding performance in terms of throughput, settling time and
50 Hz/60 Hz rejection.
FILTER GAIN (dB)
–30
–40
–50
–60
–70
–80
–90
–100
0
25
50
75
100
125
FREQUENCY (Hz)
150
08771-059
–110
–120
Figure 49. Sinc3 Filter Response
(FS[9:0] = 96, Chop Enabled, REJ60 = 1)
Table 35. Filter Summary 1
Filter
Sinc4, Chop Disabled 3
Sinc4, Chop Disabled
Sinc3, Chop Disabled
Sinc4, Chop Disabled
Sinc3, Chop Disabled
Sinc4, Chop Disabled
Sinc4, Chop Disabled
Sinc3, Chop Disabled
Sinc3, Chop Disabled
Sinc4, Chop Disabled
Sinc3, Chop Disabled
Sinc4, Chop Disabled, Zero
Latency
Sinc4, Chop Disabled, Zero
Latency
Sinc4, Chop Disabled, Zero
Latency
Sinc4, Chop Enabled
Sinc3, Chop Enabled
FS[9:0]
1
5
5
480
480
96
96
96
96
80
80
96
Output Data
Rate (Hz)
4800
960
960
10
10
50
50
50
50
60
60
12.5
Settling
Time (ms)
0.83
4.17
3.125
400
300
80
80
60
60
66.67
50
80
Throughput 2 (Hz)
1200
240
320
2.5
3.33
12.5
12.5
16.7
16.7
15
20
12.5
REJ60
0
0
0
0
0
0
1
0
1
0
0
0
50 Hz Rejection (dB)
No 50 Hz or 60 Hz rejection
No 50 Hz or 60 Hz rejection
No 50 Hz or 60 Hz rejection
120 dB ( 50 Hz and 60 Hz)
100 dB (50 Hz and 60 Hz)
120 dB (50 Hz only)
82 dB ( 50 Hz and 60 Hz)
95 dB (50 Hz only)
67 dB ( 50 Hz and 60 Hz)
120 dB (60 Hz only)
95 dB (60 Hz only)
120 dB (50 Hz only)
96
12.5
80
12.5
1
82 dB ( 50 Hz and 60 Hz)
80
15
66.67
15
0
120 dB (60 Hz only)
96
96
12.5
16.7
160
120
6.25
8.33
1
1
80 dB (50 Hz and 60 Hz)
67 dB (50 Hz and 60 Hz)
1
These calculations assume a 4.92 MHz stable master clock.
Throughput is the rate at which conversions are available when several channels are enabled. In zero latency mode, the output data rate and throughput are equal.
3
For output dates rates greater than 1 kHz, the sinc4 filter is recommended.
2
Rev. 0 | Page 41 of 44
AD7195
GROUNDING AND LAYOUT
Because the analog inputs and reference inputs are differential,
most of the voltages in the analog modulator are commonmode voltages. The high common-mode rejection of the part
removes common-mode noise on these inputs. The analog and
digital supplies to the AD7195 are independent and separately
pinned out to minimize coupling between the analog and digital sections of the device. The digital filter provides rejection
of broadband noise on the power supplies, except at integer
multiples of the modulator sampling frequency.
Connect an R-C filter to each analog input pin to provide
rejection at the modulator sampling frequency. The digital filter
also removes noise from the analog and reference inputs provided these noise sources do not saturate the analog modulator.
As a result, the AD7195 is more immune to noise interference
than a conventional high resolution converter. However,
because the resolution of the AD7195 is so high and the noise
levels from the converter so low, care must be taken with regard
to grounding and layout.
The printed circuit board (PCB) that houses the ADC must be
designed so that the analog and digital sections are separated
and confined to certain areas of the board. This facilitates the
use of ground planes that can be easily separated. A minimum
etch technique is generally best for ground planes because it
gives the best shielding.
Although the AD7195 has separate pins for analog and digital
ground, the AGND and DGND pins are tied together internally
via the substrate. Therefore, the user must not tie these two
pins to separate ground planes unless the ground planes are
connected together near the AD7195.
In systems where AGND and DGND are connected elsewhere
in the system, they should not be connected again at the
AD7195 because this would result in a ground loop. In these
situations, it is recommended that the ground pins of the
AD7195 be tied to the AGND plane.
In any layout, the user must keep in mind the flow of currents
in the system, ensuring that the paths for all currents are as close
as possible to the paths the currents took to reach their destinations. Avoid forcing digital currents to flow through the AGND.
Avoid running digital lines under the device because this
couples noise onto the die and allow the analog ground plane
to run under the AD7195 to prevent noise coupling. The power
supply lines to the AD7195 must use as wide a trace as possible
to provide low impedance paths and reduce the effects of
glitches on the power supply line. Shield fast switching signals
like clocks with digital ground to prevent radiating noise to
other sections of the board, and never run clock signals near
the analog inputs. Avoid crossover of digital and analog signals.
Run traces on opposite sides of the board at right angles to
each other. This reduces the effects of feedthrough through
the board. A microstrip technique is by far the best but is not
always possible with a double-sided board. In this technique,
the component side of the board is dedicated to ground planes,
whereas signals are placed on the solder side.
Good decoupling is important when using high resolution ADCs.
Decouple all analog supplies with 10 μF tantalum in parallel with
0.1 μF capacitors to AGND. To achieve the best from these
decoupling components, place them as close as possible to the
device, ideally right up against the device. Decouple all logic chips
with 0.1 μF ceramic capacitors to DGND. In systems in which a
common supply voltage is used to drive both the AVDD and DVDD
of the AD7195, it is recommended that the system AVDD supply
be used. For this supply, place the recommended analog supply
decoupling capacitors between the AVDD pin of the AD7195 and
AGND and the recommended digital supply decoupling capacitor between the DVDD pin of the AD7195 and DGND.
Rev. 0 | Page 42 of 44
AD7195
APPLICATIONS INFORMATION
The AD7195 provides a low-cost, high resolution analog-todigital function. Because the analog-to-digital function is
provided by a Σ-Δ architecture, the part is more immune
to noisy environments, making it ideal for use in sensor
measurement and industrial and process control applications.
ACX2 and ACX2. In this phase, the excitation voltage to the
bridge is reversed while the analog input signal and the
reference voltage are also reversed. The AD7195 averages the
conversions from the two phases so that any offsets and thermal
affects are cancelled.
WEIGH SCALES
AC excitation is enabled by setting Bit ACX in the configuration
register to 1. When the ACX bit is set to 0, the bridge is dc
excited. When the AD7195 is in power-down mode, the bridge
is disconnected from the excitation voltage, which minimizes
power consumption of the system. Following a reset, the ac
excitation pins are undefined for a few milliseconds. Thus, pullup/pull-down resistors should be used on the pins to prevent
the excitation voltage being shorted to AGND.
Figure 50 shows the AD7195 being used in a weigh scale application which uses ac excitation. The load cell is arranged in a bridge
network and gives a differential output voltage between its OUT+
and OUT– terminals. Assuming a 5 V excitation voltage, the full
-scale output range from the transducer is 10 mV when the
sensitivity is 2 mV/V. The excitation voltage for the bridge can
be used to directly provide the reference for the ADC because
the reference input range includes the supply voltage.
For simplicity, external filters are not included in Figure 50.
However, an R-C antialias filter must be included on each
analog input. This is required because the on-chip digital filter
does not provide any rejection around the modulator sampling
frequency or multiples of this frequency.
With ac-excitation, the excitation voltage to the load cell is
changed on each phase. In Phase 1, the T2 and T4 transistors
are turned on using ACX1 and ACX1 while the T1 and T3
transistors are turned off. The bridge is forward biased. During
Phase 2, Transistor T1 and Transistor T3 are turned on using
+5V
T1
T2
REFIN(+) AVDD AGND
IN+
AIN1
AIN2
AIN3
AIN4
OUT+
OUT–
REFERENCE
DETECT
AVDD
AINCOM
IN–
DVDD DGND
MUX
Σ-Δ
ADC
PGA
REFIN(–)
SERIAL
INTERFACE
AND
CONTROL
LOGIC
DOUT/RDY
DIN
SCLK
CS
SYNC
AGND
T4
TEMP
SENSOR
BPDSW
AVDD
AD7195
1MΩ
ACX1
ACX1
AC
EXCITATION
CLOCK
ACX2
CLOCK
CIRCUITRY
ACX2
MCLK1 MCLK2
08771-032
T3
1MΩ
Figure 50. Typical Application (Weigh Scale)
Rev. 0 | Page 43 of 44
AD7195
OUTLINE DIMENSIONS
0.30
0.25
0.18
32
25
0.50
BSC
0.80
0.75
0.70
0.50
0.40
0.30
8
16
9
BOTTOM VIEW
0.05 MAX
0.02 NOM
COPLANARITY
0.08
0.20 REF
SEATING
PLANE
3.65
3.50 SQ
3.45
EXPOSED
PAD
17
TOP VIEW
PIN 1
INDICATOR
1
24
0.25 MIN
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
COMPLIANT TO JEDEC STANDARDS MO-220-WHHD.
112408-A
PIN 1
INDICATOR
5.10
5.00 SQ
4.90
Figure 51. 32-Lead Lead Frame Chip Scale Package [LFCSP-WQ]
5 mm × 5 mm Body, Very Very Thin Quad
(CP-32-11)
Dimensions shown in millimeters
ORDERING GUIDE
Model 1
AD7195BCPZ
AD7195BCPZ-RL
AD7195BCPZ-RL7
1
Temperature Range
–40°C to +105°C
–40°C to +105°C
–40°C to +105°C
Package Description
32-Lead LFCSP_WQ
32-Lead LFCSP_WQ
32-Lead LFCSP_WQ
Z = RoHS Compliant Part.
©2010 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D08771-0-1/10(0)
Rev. 0 | Page 44 of 44
Package Option
CP-32-11
CP-32-11
CP-32-11