AMS AMS2026

AMS2026
FEATURES
• 110mΩ Typ. (5V Input) High Side MOSFET Switch
• Short Circuit Protection
• Overcurrent Protection
• Thermal Protection
• Enable Input Compatible With 3V and 5V Logic
• Controlled Rise and Fall Times Limit Current
Surges and Minimize EMI
• Undervoltage Lock-Out Guarantees the Switch is
Off At Start-up
• 100µA Maximum On-State Supply Current
• Available Active-High or Active-Low Enable
• Available in Space Saving 8 lead SOIC and 8 lead PDIP
APPLICATIONS
• USB Power Management
• Hot Plug-In Power Supplies
• Battery-Charger Circuits
PRODUCT DESCRIPTION
The AMS2026 is a dual power distribution switch intended for applications where heavy capacitive loads and short-circuits are
likely to be encountered. The high-side switch is a 110mΩ N-channel MOSFET. The switch is controlled by a logic enable
input compatible with 3V and 5V logic and is available in active-high or active-low enable. The internal charge pump,
designed to control the power switch rise and fall time to minimize current surges during switching, also provides the gate
drive. Requiring no external components the charge pump allows operation from supplies as low as 3.3V. When an overload
or a short circuit is encountered the AMS2026 limits the output current to a safe level by switching into a constant-current
mode and the overcurrent logic output error flag is set to a low. Continuous heavy overloads and short circuits will increase the
power dissipation in the switch; this will cause the junction temperature to rise. The thermal protection circuit shuts the power
switch off to prevent damage. Once the device has cooled sufficiently, it will turn on automatic. An under voltage lock-out is
provided to insure that the power switch is in the Off state at start-up.
The AMS2026 is offered in the 8 lead SOIC package and the 8 lead PDIP package.
ORDERING INFORMATION
PACKAGE TYPE
8 LEAD SOIC
AMS2026S
PIN CONNECTIONS
8 LEAD SOIC/ 8 LEAD PDIP
OPER. TEMP
8 LEAD PDIP
AMS2026P
RANGE
-40°C to 85°C
ENABLE
1
8 OUTPUT
ERROR
2
7
ERROR
3
6 GROUND
ENABLE
4
5
Top View
1
Advanced Monolithic Systems
http://www.ams-semitech.com
INPUT
OUTPUT
AMS2026
ABSOLUTE MAXIMUM RATINGS (Note 1)
Input Voltage Range, VI
Output Voltage Range, VO
Input Voltage Range, VI at /EN
Continuos Output Current, IO
-0.3V to 7V
-0.3V to VI(IN)
+0.3V
-0.3V to 7V
Internally Limited
Internal Power Dissipation
Maximum Junction Temperature
Storage Temperature
Lead Temperature (Soldering 25 sec)
(Note 3)
+125°C
-65°C to +150°C
265°C
ELECTRICAL CHARACTERISTICS
Electrical Characteristics for each section at TJ=25°C, VI(IN) = 5.5V, IO =rated current, /EN = 0V unless otherwise specified.
AMS2026
Typ.
Max.
VI(IN) = 5.5V
110
140
mΩ
VI(IN) = 5.0V
110
140
mΩ
VI(IN) = 4.5V
110
140
mΩ
VI(IN) = 4.0V
110
140
mΩ
/EN = VI
0.01
5
µA
PARAMETER
CONDITIONS
Min.
(Note 2)
Switch On-State Resistance
Switch Output Leakage Current
/EN = VI , -40°C ≤ TJ ≤ 85°C
Switch Output Rise Time
Switch Output Fall Time
µA
VI(IN) = 5.5V, CL = 1µF
ms
VI(IN) = 2.7V, CL = 1µF
3.8
ms
VI(IN) = 5.5V, CL = 1µF
3.9
ms
VI(IN) = 2.7V, CL = 1µF
3.5
ms
4.0V ≤ VI ≤ 5.5V
Enable Low-Level Input Voltage
4.0V ≤ VI ≤ 5.5V
Enable Input Current
/EN = 0V or /EN = VI
Short Circuit Current
10
4.0
Enable High-Level Input
Voltage
Enable Delay Time, Low-toHigh Output
Units
2.4
V
0.6
V
1
µA
CL = 1µF
20
ms
CL = 1µF
40
ms
1.2
1.8
A
0.015
10
µA
-1
VI(IN) = 5.5V, TJ=25°C
0.66
OUT Connected to GND, device enable into
short circuit
Supply Current, Low-Level
Output
/EN = VI , TJ=25°C
Supply Current, High-Level
Output
/EN = 0V, TJ=25°C
/EN = VI , -40°C ≤ TJ ≤ 85°C
73
/EN = 0V, -40°C ≤ TJ ≤ 85°C
10
µA
100
µA
100
µA
Undervoltage lock-out Low2.0
3.0
3.2
V
Level Input Voltage
Note 1: Absolute Maximum Ratings are limits beyond which damage to the device may occur. For guaranteed performance limits and associated test
conditions, see the Electrical Characteristics tables.
Note 2: To ensure constant junction temperature, low duty cycle pulse testing is used; thermal effects must be taken in consideration separately.
Note 3: The Power Dissipation for the SO-8 package is 725mW at TA = 25 °C. Above TA = 25 °C the Power Dissipation must be derated at 5.8mW/ °C (for TA
= 70 °C PD = 464mW ; for TA = 125 °C PD = 145mW)
RECOMMENDED OPERATING CONDITIONS:
Input Voltage, VI
Input Voltage, VI at /EN
Continuous Output Current, IO
Operating Junction Temp. Range
Min
4.0V
0V
0A
-40°C
Max
5.5V
5.5V
0.6A
+125°C
2
Advanced Monolithic Systems
http://www.ams-semitech.com
AMS2026
PIN FUNCTIONS
Pin Name
Enable
/EN (A/B)
Ground
GND
Input
IN
Error Flag ERROR (A/B)
Output
OUT(A/B)
Pin No.
1/4
6
7
2/3
6-8
I/O
I
I
I
O
O
Description
Enable Input, Logic turns power switch on.
Ground.
Power switch input, also supplies IC’s internal circuitry.
Overcurrent, Over temperature, Logic output.
Power switch output.
BLOCK DIAGRAM
POWER SWITCH
POWER SWITCH
IN
OUT A
*
CS
*
CS
OUT B
1.2V
REFERENCE
CURRENT
LIMIT
GATE
DRIVER
GATE
DRIVER
THERMAL
SENSE
ENABLE A
ERROR A
CURRENT
LIMIT
ERROR
FLAG
CHARGE
PUMP
UVLO
ENABLE B
UVLO
CHARGE
PUMP
ERROR
FLAG
ERROR B
GND
*Current Sense
FUNCTIONAL DESCRIPTION
Power Switch
The power switch is an N-channel MOSFET with a maximum onstate resistance of 140mΩ (VI(IN) = 5.0V, configured as a high-side
switch.
Charge Pump
An internal 100kHz charge pump supplies the power to the driver
circuit and provides the required voltage to pull the gate of the
MOSFET above the source. The charge pump requires very little
supply current and operates from input voltages as low as 3.0V.
Gate Driver
The driver controls the gate voltage of the power switch. The
driver incorporates circuitry that controls the rise and fall times of
the output voltage, as a result it limits large current surges and
reduces the associated electromagnetic interference (EMI)
produced. The rise and fall times of the output voltage are
typically in the 2ms to 4ms range instead of the microsecond or
nanosecond range for a standard FET.
Enable
A logic high on the /EN input turns off the power switch and the
bias for the charge pump, driver, and other circuitry to reduce the
supply current to less than 10µA. A logic zero input restore bias to
the drive and control circuits and turns the power on. The enable
input is compatible with both TTL and CMOS logic levels.
Error Flag
The error flag output, is an open drain logic output that is active
low when output current exceeds current limit. Until the fault
condition is removed the output will remain active low.
Current Limit
A sense FET monitors the current supplied to the load. In case of
an overload or short circuit, the current limit circuitry sends a
signal to the driver. The driver will then reduce the gate voltage
and drive the power FET into its linear region, which switches the
output into a constant current mode and holds the current constant
while varying the voltage on the load.
Thermal Shutdown
The internal thermal shutdown circuit will shut the power switch
off when the junction temperature rises to approx. 180°C.
Hysteresis is build into the thermal sense circuitry, and after the
junction temperature has dropped about 20°C, the switch turns
back on. Until the fault is removed the switch will continue to
cycle off and on.
Undervoltage Lock-out
An internal voltage sense monitors the input voltage. When the
input voltage is below 3.2V nominal, the switch is turned off by a
control signal. The typical fall time range due to the sense of a
low voltage is 250µs to 750µs.
3
Advanced Monolithic Systems
http://www.ams-semitech.com
AMS2026
APPLICATION HINTS
As an initial estimate use the highest operating ambient
temperature of interest and read rON from Figure 1. Power
dissipation is equal to:
Power Supply Considerations
A 0.047µF ceramic bypass capacitor close to the device, between
input and ground is recommended. When the output load is heavy
or has large paralleled capacitors, a high value electrolytic capacitor
should be used. To improve the immunity of the device to ESD, use
a 0.1µF ceramic capacitor to bypass the output.
PD = rON x I2
Calculate the junction temperature:
TJ = PD x RθJA + TA
Where RθJA is the thermal resistance and is 172°C/W for the
SOIC package. Compare the calculated junction temperature
with the initial estimate and if they don’t mach within a few
degrees, repeat the calculations using the calculated value as the
new estimate. A few repetitions will be sufficient to give a
reasonable answer.
Current Limit
A sense FET monitors overcurrent conditions. When an overcurrent
condition is detected the device maintains a constant output current
and decreases the voltage accordingly. If the condition is present
long enough to activate the thermal limiting the result is the
shutdown of the device.
There are three situation in which overload can occur. In the first
case, the output has been shorted before the device is enabled or
before VI has been applied. The device senses the short and
switches into a constant-current output.
In the second case, the short occurs while the device is enabled.
When this happens, very high currents flow for a short time before
the current-limit circuit can react. After the current-limit circuit has
tripped, the device limits normally.
In the third case, the load has been gradually increased beyond the
recommended operating current. The current will rise until the
current-limit threshold is reached. The AMS2026 is able to deliver
current up to the current-limit threshold without damage. When the
threshold has been reached the device switches into the constant
current mode. When over current condition is detected the error flag
logic output remains low until the condition is removed.
Thermal Protection
Thermal protection prevents damage to the device when over
load or short circuits conditions are present for extended periods
of time. These conditions force the AMS2026 into the constant
current mode. As a result the voltage across the high-side switch
will increase. Under short-circuit conditions the voltage across
the switch is equal to the input voltage. Continuous short circuits
and heavy over loads increase the power dissipation in the switch
and causes the junction temperature to rise to dangerously high
levels. The protection circuit shuts off the switch when it senses
the high junction temperature. The switch remains off until the
device has cooled about 20°C. The switch continues to cycle off
and on until the fault is removed.
Undervoltage Lock-out
Power Dissipation and Junction Temperature
An undervoltage lock-out is provided to insure that the switch is
in the off state at start-up. When the input voltage falls below
3.0V the switch will be turned off immediately. This will make it
easy for designers of hot plug-in systems that may not be able to
turn the switch off before removing the input power. In such
cases when the device is reinserted, the turn on will have a
controlled rise time to reduce EMI and voltage overshoots.
The thermal resistance of the surface-mount packages such as SOIC
is high compared to that of power packages. The use of the Ncannel MOSFET which has low on-resistance, makes it possible for
small surface-mount packages to pass large currents. To determine
the power dissipation and junction temperature the first step is to
find rON at the input voltage and operating temperature.
TYPICAL APPLICATIONS
7
POWER SUPPLY
4.0V - 5.0V
1µF
OUT A
0.1µF
10k
2
3
1
4
ERROR A
ERROR B
EN
EN
OUT B
GND
6
Figure 1
4
Advanced Monolithic Systems
EXTERNAL LOAD A
8
0.1µF
10k
ERROR FLAG A
ERROR FLAG B
ENABLE A
ENABLE B
IN
http://www.ams-semitech.com
EXTERNAL LOAD B
5
0.1µF
AMS2026
PACKAGE DIMENSIONS inches (millimeters) unless otherwise noted.
8 LEAD SOIC PLASTIC PACKAGE (S)
0.189-0.197*
(4.801-5.004)
8
7
6
5
0.228-0.244
(5.791-6.197)
0.150-0.157**
(3.810-3.988)
1
2
3
4
0.010-0.020 x 45°
(0.254-0.508)
0.053-0.069
(1.346-1.752)
0.004-0.010
(0.101-0.254)
0.014-0.019
(0.355-0.483)
0.008-0.010
(0.203-0.254)
0.050
(1.270)
TYP
0°-8° TYP
0.016-0.050
(0.406-1.270)
S (SO-8 ) AMS DRW# 042293
*DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
**DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
8 LEAD PLASTIC DIP PACKAGE (P)
0.400*
(10.160)
MAX
8
7
6
5
1
2
3
4
0.255±0.015*
(6.477±0.381)
0.045-0.065
(1.143-1.651)
0.300-0.325
(7.620-8.255)
0.130±0.005
(3.302±0.127)
0.065
(1.651)
TYP
0.005
(0.127)
MIN
0.100±0.010
(2.540±0.254)
0.009-0.015
(0.229-0.381)
0.125
(3.175)
MIN
0.015
(0.380)
MIN
0.018±0.003
(0.457±0.076)
0.325 +0.025
-0.015
(8.255 +0.635 )
-0.381
P (8L PDIP ) AMS DRW# 042294
*DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTUSIONS.
MOLD FLASH OR PROTUSIONS SHALL NOT EXCEED 0.010" (0.254mm)
5
Advanced Monolithic Systems
http://www.ams-semitech.com