AME, Inc. AME8807 n General Description 600mA CMOS LDO n Functional Block Diagram The AME8807 family of positive, linear regulators feature low ground current (30µA typ.) with low dropout voltage, making them ideal for battery applications. The space-saving SO-8 package is attractive for "Pocket" and "Hand Held" applications. IN OUT Overcurrent Shutdown These rugged devices have both Thermal Shutdown, and Current Fold-back to prevent device failure under the "Worst" of operating conditions. Thermal Shutdown EN The AME8807 is stable with an output capacitance of 2.2µF or greater. AMP ADJ n Features Vref =1.215V GND l Very Low Dropout Voltage l Guaranteed 600mA Output l Typical 30µA Ground Current l Accurate to within 1.5% l Over-Temperature Shutdown n Typical Application l Current Limiting l Short Circuit Current Fold-back l Power-Saving Shutdown Mode EN IN IN l Space-Saving SO-8 Package l User Adjustable Output Voltages C1 l Low Temperature Coefficient l All AME's Lead Free Products Meet RoHS Standards 1µF OUT OUT AME8807 GND ADJ C2 R1 100p C3 2.2µF R2 n Applications l Instrumentation l Portable Electronics l Wireless Devices l Cordless Phones l PC Peripherals VOUT = 1.215 ( R1/R2 +1 ) C2 is unnecessary if R1 or R2 < 20 K Ohms R R and R use resistance value within 1% accuracy for 1 2 and correct VOUT l Battery Powered Widgets l Electronic Scales 1 AME, Inc. AME8807 600mA CMOS LDO n Pin Configuration SO-8 Top View 8 7 6 SO-8 Top View 5 AME8807 AME8807AEHA 8 7 6 5 1. IN 1. OUT 2. GND 2. ADJ 3. GND AME8807 4. EN 5. ADJ 2 3 4 3. GND 4. NC 5. EN 6. GND 1 AME8807BEHA 6. NC 1 7. GND 2 3 4 7. NC 8. OUT 8. IN * Die Attach: * Die Attach: Conductive Epoxy Conductive Epoxy n Ordering Information AME8807 x x x x x Special Feature Number of Pins Package Type Operating Ambient Temperature Range Pin Configuration Pin Operating Ambient Configuration Temperature Range A: 1. IN 2. GND 3. GND 4. EN 5. ADJ 6. GND 7. GND 8. OUT B: 1. 2. 3. 4. 5. 6. 7. 8. 2 OUT ADJ GND NC EN NC NC EN E: -40 O C to 85 O C Package Type H: SO-8 Number of Pins A: 8 Special Feature Z: Lead Free AME, Inc. AME8807 600mA CMOS LDO n Ordering Information Part Number Marking* Output Voltage Package Operating Ambient Temperature Range AME8807AEHA 8807 AEHA yyww Adjustable SO-8 - 40oC to + 85oC AME8807AEHAZ 8807 AEHA yyww Adjustable SO-8 - 40oC to + 85oC AME8807BEHA 8807 BEHA yyww Adjustable SO-8 - 40oC to + 85oC AME8807BEHAZ 8807 BEHA yyww Adjustable SO-8 - 40oC to + 85oC Note: yyww represents the date code * A line on top of the first letter represents lead free plating such as 8807 Please consult AME sales office or authorized Rep./Distributor for package type availability. 3 AME, Inc. AME8807 600mA CMOS LDO n Absolute Maximum Ratings Parameter Maximum Unit 8 V Output Current PD / (V IN - VO) A Output Voltage GND - 0.3 to VIN + 0.3 V Input Voltage B* ESD Classification Caution: Stress above the listed absolute maximum rating may cause permanent damage to the device. *HBM B:2000V~3999V n Recommended Operating Conditions Parameter Symbol Rating Unit Ambient Temperature Range TA - 40 to + 85 o C Junction Temperature Range TJ - 40 to + 125 o C n Thermal Information Parameter Package Die Attach Thermal Resistance* (Junction to Case) Thermal Resistance (Junction to Ambient) Maximum θJC 60 Unit o SO-8 Conductive Epoxy Internal Power Dissipation θJA 150 PD 810 C/W mW Maximum Junction Temperature 150 o C Solder Iron (10 Sec)** 350 o C * Measure θJC on center of molding compound if IC has no tab. O ** MIL-STD-202G 210F F 4 Symbol AME, Inc. AME8807 600mA CMOS LDO n Electrical Specifications TA = 25OC unless otherwise noted Parameter Symbol Input Voltage VIN Output Voltage Accuracy VO Dropout Voltage VDROPOUT Test Condition IO=1mA Min Typ Max Note 1 7 V -1.5 1.5 % 1.5V<VO(NOM)<=2.0V IO=600mA VO=VO(NOM) -2.0% 1400 See chart 2.0V<VO(NOM)<=2.8V 2.8V<VO(NOM) Output Current Units 800 mV 600 IO VO>1.2V 600 Current Limit ILIM VO>1.2V 600 Short Circuit Current ISC VO<0.8V 300 600 mA IQ IO=0mA 30 50 µA IGND IO=1mA to 600mA 30 Quiescent Current (For Fixed Output Voltage Options) Ground Pin Current Line Regulation REGLINE Load Regulation REGLOAD Over Temperature Shutdown Over Temperature Hysterisis VO Temperature Coefficient Power Supply Rejection Output Voltage Noise ADJ Reference Voltage EN Input Threshold EN Input Bias Current Shutdown Supply Current IO=1mA VO < 2.0V VIN=VO+1 to V O+2 VO >= 2.0V IO=1mA to 600mA mA 800 mA µA 0.15 % 0.02 0.1 % 0.2 1 % 150 o OTH 30 o TC 30 OTS PSRR eN IO=100mA CO=2.2µF f=10Hz to 100kHz IO=10mA C C ppm/oC f=1kHz 50 f=10kHz 20 f=100kHz 15 Co=2.2µF 30 µVrms 1.203 1.215 1.227 V VREF dB VEH VIN =2.7V to 7V 2.0 Vin V VEL VIN =2.7V to 7V 0 0.4 V IEH VEN =VIN , VIN=2.7V to 7V 0.1 µA IEL VEN =0V, VIN=2.7V to 7V 0.5 µA ISD VIN =5V, V O=0V, VEN <VEL 1 µA 0.5 Note1:VIN(min) =VOUT+VDROPOUT 5 AME, Inc. AME8807 600mA CMOS LDO n Detailed Description n Enable The AME8807 family of CMOS regulators contain a PMOS pass transistor, voltage reference, error amplifier, over-current protection, and thermal shutdown. The Enable pin normally floats high. When actively, pulled low, the PMOS pass transistor shuts off, and all internal circuits are powered down. In this state, the quiescent current is less than 1µA. This pin behaves much like an electronic switch. The P-channel pass transistor receives data from the error amplifier, over-current shutdown, and thermal protection circuits. During normal operation, the error amplifier compares the output voltage to a precision reference. Over-current and Thermal shutdown circuits become active when the junction temperature exceeds 150oC, or the current exceeds 600mA. During thermal shutdown, the output voltage remains low. Normal operation is restored when the junction temperature drops below 120oC. The AME8807 switches from voltage mode to current mode when the load exceeds the rated output current. This prevents over-stress. The AME8807 also incorporates current foldback to reduce power dissipation when the output is short circuited. This feature becomes active when the output drops below 0.8 volts, and reduces the current flow by 65%. Full current is restored when the voltage exceeds 0.8 volts. n External Capacitors The AME8807 is stable with an output capacitor to ground of 2.2µF or greater. Ceramic capacitors have the lowest ESR, and will offer the best AC performance. Conversely, Aluminum Electrolytic capacitors exhibit the highest ESR, resulting in the poorest AC response. Unfortunately, large value ceramic capacitors are comparatively expensive. One option is to parallel a 0.1µF ceramic capacitor with a 10µF Aluminum Electrolytic. The benefit is low ESR, high capacitance, and low overall cost. A second capacitor is recommended between the input and ground to stabilize Vin. The input capacitor should be at least 0.1µF to have a beneficial effect. All capacitors should be placed in close proximity to the pins. A "Quiet" ground termination is desirable. This can be achieved with a "Star" connection. 6 n ADJ The ADJ pin is the positive input to the error amplifier which, due to the pmos pass element inversion, means it is actually the negative input of the LDO feedback loop. The feedback works to keep the voltage at the ADJ pin 1.215V with respect to ground. Since the internal circuitry at the ADJ pin is essentially an ESD protected CMOS gate the input current at the ADJ pin is virtually zero. AME, Inc. AME8807 600mA CMOS LDO Ground Current vs. Input Voltage Load Step (1mA-600mA) Vo(10mV/DIV) 45 85 OC 35 30 25 Output C L=2.2µF CIN=2.2µF O 25 C 20 15 10 5 0 0 1 2 3 4 5 6 7 8 IL(200mA/DIV) Ground Current (µ A) 40 I Load 0 Input Voltage (V) TIME (20mS/DIV) Drop Out Voltage vs. Output Voltage Power Supply Rejection Ratio 0 1400 Top to Bottom ILOAD=600mA ILOAD=500mA ILOAD=400mA ILOAD=300mA ILOAD=200mA ILOAD=100mA 1000 800 600 -10 100mA CL=2.2µF Tantalum Tantalum C BYP=0 -20 PSRR (dB) Dr op Out Voltage (mV) 1200 -30 -40 -50 10mA 100mA 400 -60 200 -70 1 2 3 4 5 100 µ A 100 µ A 1mA -80 6 10 Output Voltage (V) 1K 100K 10M Frequency (Hz) Safe Operating Area Noise Measurement 600 8807BEHA Vo (1mV DIV) Output Current (mA) 8807AEHA 100 10 0.1 1.0 Input-Output Voltage Differential (V) C L=2.2µF No Filter 8.0 TIME (20ms/DIV) 7 AME, Inc. AME8807 600mA CMOS LDO Current Limit Response I OU T (200mA/DIV) VOUT (1V/DIV) Overtemperature Shutdown 0 IOUT (200mA/DIV) VOUT (1V/D IV) RLOAD=6.6 Ω 0 TIME (0.5Sec/DIV) TIME (2mS/DIV) TIME (2mS/DIV) V IN (1V/DIV) Line Transient Response VOUT (10mV/DIV) Enable (2V/DIV) Chip Enable Transient Response C L=2µF R L=10Ω 0 Output (1V/DIV) C LOAD=2.2µF C IN=1µF R LOAD <100mΩ VOUT (1V/DIV) IOUT (200mV/DIV) Short Circuit Response C LOAD=2.2µF ILOAD =1mA VOUTDC=3.3V VINDC=4.5V TIME (200mS/DIV) 8 C LOAD =2.2µF C IN=1.0µF RLOAD=3.3Ω VOUTNOM =3.3V 0 TIME (1mS/DIV) AME, Inc. AME8807 600mA CMOS LDO n External Resistor Divider Table R1 (K Ohm) 1 2 4 5 6 7 8 9 10 114.35 72.00 52.54 41.36 34.11 29.01 25.25 22.34 20.04 18.17 16.62 15.31 14.19 13.22 12.38 11.64 10.98 10.40 9.87 9.39 8.96 8.56 8.20 7.87 7.56 7.28 7.02 6.77 6.55 6.33 6.13 5.94 5.77 5.60 5.45 5.30 5.16 128.65 81.00 59.11 46.53 38.37 32.64 28.40 25.14 22.55 20.44 18.69 17.22 15.96 14.88 13.93 13.10 12.36 11.70 11.10 10.57 10.08 9.63 9.23 8.85 8.51 8.19 7.90 7.62 7.36 7.12 6.90 6.69 6.49 6.30 6.13 5.96 5.80 142.94 90.00 65.68 51.70 42.63 36.27 31.56 27.93 25.05 22.71 20.77 19.13 17.74 16.53 15.48 14.55 13.73 12.99 12.34 11.74 11.20 10.70 10.25 9.84 9.46 9.10 8.77 8.47 8.18 7.92 7.67 7.43 7.21 7.00 6.81 6.62 6.45 R2(K Ohm)=(1.215*R1(K Ohm))/(Vout-1.215) Vout 1.30 1.35 1.40 1.45 1.50 1.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15 2.20 2.25 2.30 2.35 2.40 2.45 2.50 2.55 2.60 2.65 2.70 2.75 2.80 2.85 2.90 2.95 3.00 3.05 3.10 3 14.29 9.00 6.57 5.17 4.26 3.63 3.16 2.79 2.51 2.27 2.08 1.91 1.77 1.65 1.55 1.46 1.37 1.30 1.23 1.17 1.12 1.07 1.03 0.98 0.95 0.91 0.88 0.85 0.82 0.79 0.77 0.74 0.72 0.70 0.68 0.66 0.64 28.59 18.00 13.14 10.34 8.53 7.25 6.31 5.59 5.01 4.54 4.15 3.83 3.55 3.31 3.10 2.91 2.75 2.60 2.47 2.35 2.24 2.14 2.05 1.97 1.89 1.82 1.75 1.69 1.64 1.58 1.53 1.49 1.44 1.40 1.36 1.32 1.29 42.88 27.00 19.70 15.51 12.79 10.88 9.47 8.38 7.52 6.81 6.23 5.74 5.32 4.96 4.64 4.37 4.12 3.90 3.70 3.52 3.36 3.21 3.08 2.95 2.84 2.73 2.63 2.54 2.45 2.37 2.30 2.23 2.16 2.10 2.04 1.99 1.93 57.18 36.00 26.27 20.68 17.05 14.51 12.62 11.17 10.02 9.08 8.31 7.65 7.09 6.61 6.19 5.82 5.49 5.20 4.93 4.70 4.48 4.28 4.10 3.94 3.78 3.64 3.51 3.39 3.27 3.17 3.07 2.97 2.88 2.80 2.72 2.65 2.58 71.47 45.00 32.84 25.85 21.32 18.13 15.78 13.97 12.53 11.36 10.38 9.57 8.87 8.27 7.74 7.28 6.86 6.50 6.17 5.87 5.60 5.35 5.13 4.92 4.73 4.55 4.39 4.23 4.09 3.96 3.83 3.72 3.61 3.50 3.40 3.31 3.22 85.76 54.00 39.41 31.02 25.58 21.76 18.94 16.76 15.03 13.63 12.46 11.48 10.64 9.92 9.29 8.73 8.24 7.80 7.40 7.04 6.72 6.42 6.15 5.90 5.67 5.46 5.26 5.08 4.91 4.75 4.60 4.46 4.33 4.20 4.08 3.97 3.87 100.06 63.00 45.97 36.19 29.84 25.39 22.09 19.55 17.54 15.90 14.54 13.39 12.42 11.57 10.83 10.19 9.61 9.10 8.63 8.22 7.84 7.49 7.18 6.89 6.62 6.37 6.14 5.93 5.73 5.54 5.37 5.20 5.05 4.90 4.76 4.63 4.51 9 AME, Inc. AME8807 600mA CMOS LDO n External Resistor Divider Table (contd.) R1 (K Ohm) 1 2 3 10 5 6 7 8 9 10 5.02 4.90 4.78 4.66 4.55 4.45 4.35 4.25 4.16 4.08 3.99 3.91 3.83 3.76 3.69 3.62 3.55 3.49 3.43 3.37 3.31 3.26 3.20 3.15 3.10 3.05 3.00 2.96 2.91 2.87 2.83 2.79 2.75 2.71 2.67 2.64 2.60 2.57 5.65 5.51 5.37 5.24 5.12 5.00 4.89 4.79 4.68 4.58 4.49 4.40 4.31 4.23 4.15 4.07 4.00 3.93 3.86 3.79 3.73 3.66 3.60 3.54 3.49 3.43 3.38 3.33 3.28 3.23 3.18 3.14 3.09 3.05 3.01 2.97 2.93 2.89 6.28 6.12 5.97 5.83 5.69 5.56 5.44 5.32 5.20 5.09 4.99 4.89 4.79 4.70 4.61 4.53 4.44 4.36 4.29 4.21 4.14 4.07 4.00 3.94 3.88 3.81 3.76 3.70 3.64 3.59 3.54 3.49 3.44 3.39 3.34 3.30 3.25 3.21 R2(K Ohm)=(1.215*R1(K Ohm))/(Vout-1.215) Vout 3.15 3.20 3.25 3.30 3.35 3.40 3.45 3.50 3.55 3.60 3.65 3.70 3.75 3.80 3.85 3.90 3.95 4.00 4.05 4.10 4.15 4.20 4.25 4.30 4.35 4.40 4.45 4.50 4.55 4.60 4.65 4.70 4.75 4.80 4.85 4.90 4.95 5.00 4 0.63 0.61 0.60 0.58 0.57 0.56 0.54 0.53 0.52 0.51 0.50 0.49 0.48 0.47 0.46 0.45 0.44 0.44 0.43 0.42 0.41 0.41 0.40 0.39 0.39 0.38 0.38 0.37 0.36 0.36 0.35 0.35 0.34 0.34 0.33 0.33 0.33 0.32 1.26 1.22 1.19 1.17 1.14 1.11 1.09 1.06 1.04 1.02 1.00 0.98 0.96 0.94 0.92 0.91 0.89 0.87 0.86 0.84 0.83 0.81 0.80 0.79 0.78 0.76 0.75 0.74 0.73 0.72 0.71 0.70 0.69 0.68 0.67 0.66 0.65 0.64 1.88 1.84 1.79 1.75 1.71 1.67 1.63 1.60 1.56 1.53 1.50 1.47 1.44 1.41 1.38 1.36 1.33 1.31 1.29 1.26 1.24 1.22 1.20 1.18 1.16 1.14 1.13 1.11 1.09 1.08 1.06 1.05 1.03 1.02 1.00 0.99 0.98 0.96 2.51 2.45 2.39 2.33 2.28 2.22 2.17 2.13 2.08 2.04 2.00 1.96 1.92 1.88 1.84 1.81 1.78 1.75 1.71 1.68 1.66 1.63 1.60 1.58 1.55 1.53 1.50 1.48 1.46 1.44 1.41 1.39 1.37 1.36 1.34 1.32 1.30 1.28 3.14 3.06 2.99 2.91 2.85 2.78 2.72 2.66 2.60 2.55 2.49 2.44 2.40 2.35 2.31 2.26 2.22 2.18 2.14 2.11 2.07 2.04 2.00 1.97 1.94 1.91 1.88 1.85 1.82 1.79 1.77 1.74 1.72 1.69 1.67 1.65 1.63 1.61 3.77 3.67 3.58 3.50 3.41 3.34 3.26 3.19 3.12 3.06 2.99 2.93 2.88 2.82 2.77 2.72 2.67 2.62 2.57 2.53 2.48 2.44 2.40 2.36 2.33 2.29 2.25 2.22 2.19 2.15 2.12 2.09 2.06 2.03 2.01 1.98 1.95 1.93 4.40 4.28 4.18 4.08 3.98 3.89 3.81 3.72 3.64 3.57 3.49 3.42 3.36 3.29 3.23 3.17 3.11 3.05 3.00 2.95 2.90 2.85 2.80 2.76 2.71 2.67 2.63 2.59 2.55 2.51 2.48 2.44 2.41 2.37 2.34 2.31 2.28 2.25 AME, Inc. AME8807 600mA CMOS LDO n Tape and Reel Dimension SO-8L P PIN 1 W Carrier Tape, Number of Components Per Reel and Reel Size Package Carrier Width (W) Pitch (P) Part Per Full Reel Reel Size SO-8L 12.0±0.1 mm 4.0±0.1 mm 2500pcs 330±1 mm 11 AME, Inc. AME8807 600mA CMOS LDO n Package Dimension SO-8L SYMBOLS Top View MAX MIN MAX A 1.35 1.75 0.05315 0.0689 A1 0.10 0.30 0.00394 0.01181 A2 E H D L θ Front View INCHES MIN Side View C MILLIMETERS 1.473 REF 0.05799 REF B 0.33 0.51 0.01299 0.02008 C 0.19 0.25 0.00748 0.00984 D 4.80 5.33 0.18898 0.20984 E 3.80 4.00 0.14961 0.15748 1.27 BSC e 0.05000 BSC L 0.40 1.27 0.01575 0.05000 H 5.80 6.30 0.22835 0.24803 y - 0.10 e B 12 A1 A A2 7 o(4X) θ 0 o 8 o 0 o 0.00394 8o www.ame.com.tw E-Mail: [email protected] Life Support Policy: These products of AME, Inc. are not authorized for use as critical components in life-support devices or systems, without the express written approval of the president of AME, Inc. AME, Inc. reserves the right to make changes in the circuitry and specifications of its devices and advises its customers to obtain the latest version of relevant information. AME, Inc. , March 2006 Document: 2006/2095-DS8807-L.01 Corporate Headquarter AME, Inc. 2F, 302 Rui-Guang Road, Nei-Hu District Taipei 114, Taiwan, R.O.C. Tel : 886 2 2627-8687 Fax: 886 2 2659-2989 U.S.A. (Subsidiary) Analog Microelectronics, Inc. 3100 De La Cruz Blvd., Suite 201 Santa Clara, CA. 95054-2046 Tel : (408) 988-2388 Fax: (408) 988-2489