ETC TD9056

 Techcode®
ÓÉ Foxit PDF Editor ±à¼°æȨËùÓÐ (c) by Foxit Software Company, 2004
½öÓÃÓÚÆÀ¹À¡£
DATASHEET
1A Standalone Linear Li-lon Battery Charger with Thermal Regulation
TD9056A/B
汪工 TEL:13828719410 QQ:1929794238
General Description Features The TD9056 is a complete
constant-current/constant-voltage linear charger for
single cell lithium-ion batteries. Its SOP package and low
external component count make the TD9056 ideally
suited for portable applications. Furthermore, the
TD9056 can work within USB and wall adapter.
No blocking diode is required due to the internal
PMOSFET architecture and have prevent to negative
Charge Current Circuit. Thermal feedback regulates the
charge current to limit the die temperature during high
power operation or high ambient temperature. The
charge voltage is fixed at 4.2V, and the charge current
can be programmed externally with a single resistor. The
TD9056 automatically terminates the charge cycle when
the charge current drops to 1/10th the programmed value
after the final float voltage is reached.
TD9056 Other features include current monitor, under
voltage lockout, automatic recharge and two status pin to
indicate charge termination and the presence of an input
voltage. z
z
z
z
z
z
z
z
z
z
z
z
Programmable Charge Current Up to 1000mA
No MOSFET, Sense Resistor or Blocking Diode
Rquired
Complete Linear Charger in SOP-8 Package for
Single Cell Lithium-Ion Batteries
Constant-Current/Constant-Voltage
Charges Single Cell Li-Ion Batteries Directly from
USB Port
Preset 4.2V Charge Voltage with 1.5% Accuracy
Automatic Recharge
Charge Status Output Pins
C/10 Charge Termination
2.9V Trickle Charge Threshold (TD9056)
Soft-Start Limits Inrush Current
Available Radiator in SOP8/SOT23-5 Package,the
Radiator need connect GND or impending
Applications z
z
z
z
Cellular Telephones, PDAs, GPS
Charging Docks and Cradles
Digital Still Cameras, Portable Devices
USB Bus-Powered Chargers,Chargers
October, 20, 2011. Techcode Semiconductor Limited www.tongchuangwei.com
1 Techcode®
DATASHEET
1A Standalone Linear Li-lon Battery Charger with Thermal Regulation
TD9056A/B
Package Types Figure 1. Package Types of TD9056 Pin Configurations Figure 2 Pin Configuration of TD9056(Top View) October, 20, 2011. Techcode Semiconductor Limited www.tongchuangwei.com
2 Techcode®
DATASHEET
1A Standalone Linear Li-lon Battery Charger with Thermal Regulation
TD9056A/B
Pin Description Pin Name
Pin
Number
TD9056A
Description
TD9056B
TEMP
1
PROG
2
Connecting TEMP pin to NTC thermistor’s output in Lithium ion battery
pack. If TEMP pin’s voltage is below 45% or above 80% of supply voltage
VIN for more than 0.15S, this means that battery’s temperature is too high
or too low, charging is suspended. The temperature sense function can be
disabled by grounding the TEMP pin. charge current is set by connecting a resistor RISET from this pin to GND.
When in precharge mode, the ISET pin’s voltage is regulated to 0.2V.
When in constant charge current mode, the ISET pin’s voltage is
regulated to 2V.In all modes during charging, the voltage on ISET pin can
be used to measure the charge current as follows:
IBAT=(VISET/RISET)*1200----(TD9056A)
IBAT=(VISET/RISET)*1250----(TD9056B)
GND
3
Vcc
4
BAT
5
STBY
6
CHRG
7
GND VIN is the power supply to the internal circuit. When VIN drops to within
30mv of the BAT pin voltage, TD9056 enters low power sleep mode,
dropping BAT pin’s current to less than 2uA.
Connect the positive terminal of the battery to BAT pin. BAT pin draws less
than 2uA current in chip disable mode or in sleep mode. BAT pin provides
charge current to the battery and provides regulation voltage of 4.2V.
When the battery Charge Termination, the
pin is pulled low by an
internal switch, otherwise
pin is in high impedance state.
When the battery is being charged, the
pin is pulled low by an
internal switch, otherwise
pin is in high impedance state.
A high input will put the device in the normal operating mode.Pulling the CE pin to
low level will put the YP4056 into disable mode. The CE pin can be driven by TTL or
CMOS logic level.(TD9056A)
This pin can test Kelvin battery voltage, and thus precisely modulated constant
CE
FB
8
voltage battery charging voltage, avoiding the positive from the battery to the BAT pin
LN2051 or contact resistance between the resistance wire and other parasitic
resistance of the charge. If the FB pin and the BAT pin is an indirect one resistor, users
can adjust the constant charging voltage(TD9056B)
October, 20, 2011. Techcode Semiconductor Limited www.tongchuangwei.com
3 Techcode®
DATASHEET
TD9056A/B
1A Standalone Linear Li-lon Battery Charger with Thermal Regulation
Ordering Information TD9056 □ □
□ Circuit Type Packing:
A/B
Blank:Tube
R:Type and Reel
BLANK
M:SOP-8PP
Electrical Characteristics (VIN = 5V, VOUT=12V, IOUT=100mA, TA = 25°C unless otherwise specified)
Parameters
Symbol
Test Condition
Min.
Typ.
Max.
Unit
Input Supply Voltage
VCC
4.0 5 8.0 V Input Supply Current
ICC Charge Mode, RPROG =
150 55 55 500 100 100 µ A 1.2kStandbyMode(Charge
Terminated)Shutdown
Mode (RPROG Not
Connected,VCC < VBAT, or
VCC< VUV) Regulated Output (Float) Voltage
BAT Pin Current Test
VFLOAL 0℃≤TA≤85℃,IBAT=40mA
4.137 4.2 4.263 V IBAT RPROG = 2.4k, Current
450 950 0 500 1000 ‐2.5 550 1050 ‐2.6 mA mA uA Mode
RPROG = 1.2k, Current
Mode Standby Mode,
VBAT = 4.2V Trickle Charge Current
ITRIKL VBAT<VTRIKL, RPROG=1.2K
120 130 140 mA Trickle Charge Threshold Voltage
VTRIKL RPROG=1.2K, VBAT Rising
2.8 2.9 3.0 V Trickle Charge Hysteresis Voltage
VTRHYS RPROG=1.2K
60 80 100 mV Junction Temperature in Constant
TLIM 145 ℃ Temperature Mode October, 20, 2011. Techcode Semiconductor Limited www.tongchuangwei.com
4 Techcode®
DATASHEET
1A Standalone Linear Li-lon Battery Charger with Thermal Regulation
TD9056A/B
Typical Performance Characteristics October, 20, 2011. Techcode Semiconductor Limited www.tongchuangwei.com
5 Techcode®
1A Standalone Linear Li-lon Battery Charger with Thermal Regulation
DATASHEET
TD9056A/B
Typical Application Circuit October, 20, 2011. Techcode Semiconductor Limited www.tongchuangwei.com
6 Techcode®
DATASHEET
1A Standalone Linear Li-lon Battery Charger with Thermal Regulation
TD9056A/B
indicator light state Charge state
Red LED(CHRG)
Greed LED(STDBY)
charging
bright
extinguish
Charge Termination
extinguish
bright
Vin too low;Temperature of battery
too low or too high; no battery
extinguish
extinguish
BAT PIN Connect 10u Capacitance;
No battery
Greed LED bright,Red LED Coruscate T=1-4 S
Rprog Current Setting RPROG(K)
10
5
4
3
2
1.66
1.5
1.33
1.2
IBAT(mA)
130
250
300
400
580
690
780
900
1000
October, 20, 2011. Techcode Semiconductor Limited www.tongchuangwei.com
7 Techcode®
1A Standalone Linear Li-lon Battery Charger with Thermal Regulation
DATASHEET
TD9056A/B
Package Information SOP8-PP Package Outline Dimensions
October, 20, 2011. Techcode Semiconductor Limited www.tongchuangwei.com
8 Techcode®
DATASHEET
1A Standalone Linear Li-lon Battery Charger with Thermal Regulation
TD9056A/B
Design Notes
October, 20, 2011. Techcode Semiconductor Limited www.tongchuangwei.com
9