ZGL41-100 THRU ZGL41-200A SURFACE MOUNT GLASS PASSIVATED ZENER Zener Voltage - 100 to 200 Volts Steady State Power - 1.0 Watt FEATURES DO-213AB ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ For surface mount applications ♦ Glass passivated junction ♦ Low Zener impedance ♦ Low regulation factor ♦ High temperature soldering guaranteed: 250°C/10 seconds at terminals SOLDERABLE ENDS 1st BAND D1= 0.105 0.095 (2.67) (2.41) D2 0.022 (0.56) 0.018 (0.46) 0.205 (5.2) 0.185(4.7) MECHANICAL DATA 0 D2 = D1 + - 0.008 (0.20) Case: JEDEC DO-213AB molded plastic body over passivated junction Terminals: Solder plated solderable per MIL-STD-750, Method 2026 Polarity: Red band denotes Zener diode and positive end (cathode) Mounting Position: Any Weight: 0.0046 ounce, 0.116 grams 1st band denotes type and positive end (cathode) Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. OPERATING JUNCTION AND STORAGE TEMPERATURE RANGE: TJ, TSTG: -55°C to +150°C NOMINAL ZENER VOLTAGE at IZT MAXIMUM ZENER DYNAMIC IMPEDANCE MAXIMUM DC REVERSE LEAKAGE CURRENT at VR (IR) (VR) MAXIMUM MAXIMUM SURGE INSTANTANEOUS CURRENT FORWARD VOLTAGE at 200mA (NOTE 2) (IRM) (VF) (NOTE 1) (VZ) TEST CURRENT (IZT) ZZT at IZT (Volts) (mA) (Ohms) (Ohms) (mA) (µA) (Volts) (mAdc) (VOLTS) ZGL41-100 100 3.7 250 3100 0.25 1.0 76.0 10.0 1.5 ZGL41-110 110 3.4 300 4000 0.25 1.0 83.6 9.1 1.5 ZGL41-120 120 3.1 380 4500 0.25 1.0 91.2 8.3 1.5 ZGL41-130 130 2.9 450 5000 0.25 1.0 98.8 7.7 1.5 ZGL41-140 140 2.7 525 5500 0.25 1.0 106.4 7.1 1.5 ZGL41-150 150 2.5 600 6000 0.25 1.0 114.0 6.7 1.5 ZGL41-160 160 2.3 700 6500 0.25 1.0 121.6 6.3 1.5 ZGL41-170 170 2.2 800 6750 0.25 1.0 129.2 5.9 1.5 ZGL41-180 180 2.1 900 7000 0.25 1.0 136.9 5.6 1.5 ZGL41-190 190 2.0 1050 7500 0.25 1.0 144.4 5.3 1.5 ZGL41-200 200 1.9 1200 8000 0.25 1.0 152.0 5.0 1.5 TYPE NOTES: (1) Standard voltage tolerance is ± 10%, Suffix A = ± 5% (2) Surge current is a non-repetitive, 8.3ms pulse width square wave or equivalent sine-wave superimposed on IZT per JEDEC Method (3) Maximum steady state power dissipation is 1.0 watt at TT=75°C 8/26/98 ZZK at IZK RATINGS AND CHARACTERISTIC CURVES ZGL41-100 THRU ZGL41-200A FIG. 2 - TYPICAL ZENER IMPEDANCE 1.0 60 HZ RESISTIVE OR INDUCTIVE LOAD 0.75 0.5 0.25 0 25 P.C.B. MOUNTED ON 0.31 X 0.31 0.08” (8 x 8 x 2mm) COPPER AREAS PADS 50 75 100 125 150 ZZ, DYNAMIC ZENER IMPEDANCE, OHMS PM(AV), AVERAGE POWER DISSIPATION, WATTS FIG. 1 - MAXIMUM CONTINUOUS POWER DISSIPATION 10,000 TJ=25°C IZ ma +/- 0.1 IZ(dc) 1,000 VZ=200V VZ=180V VZ=150V 100 VZ=100V 10 0.5 500 100 10 IZT, ZENER TEST CURRENT, mA 175 TERMINALS TEMPERATURE, °C FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG. 4 - TYPICAL REVERSE CHARACTERISTICS 10 1 TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE 0.1 INSTANTANEOUS REVERSE CURRENT, MICROAMPERES INSTANTANEOUS FORWARD CURRENT, AMPERES 10 TJ=100°C 1 0.1 TJ=25°C 0.01 0 40 20 60 80 PERCENT OF RATED ZENER VOLTAGE, % 0.01 0.4 0.6 0.8 1 1.2 1.4 1.6 INSTANTANEOUS FORWARD VOLTAGE, VOLTS FIG. 6 - TYPICAL ZENER VOLTAGE 220 200 TESTED at RATED IZT 180 160 140 120 1 100 80 100 110 120 130 140 150 160 170 180 190 200 VZ, ZENER VOLTAGE, VOLTS 8/26/98 10 IZT, TEST ZENER CURRENT, mA ØVZ, TEMPERATURE COEFFICIENT, mV/°C FIG. 5 - TYPICAL TEMPERATURE COEFFICIENTS 0.1 100 150 200 VZ, ZENER VOLTAGE, VOLTS 250 100