AD ADM1485JR

a
FEATURES
Meets EIA RS-485 Standard
30 Mb/s Data Rate
Single +5 V Supply
–7 V to +12 V Bus Common-Mode Range
High Speed, Low Power BiCMOS
Thermal Shutdown Protection
Short Circuit Protection
Zero Skew Driver
Driver Propagation Delay: 10 ns
Receiver Propagation Delay: 25 ns
High Z Outputs with Power Off
Superior Upgrade for LTC1485
APPLICATIONS
Low Power RS-485 Systems
DTE-DCE Interface
Packet Switching
Local Area Networks
Data Concentration
Data Multiplexers
Integrated Services Digital Network (ISDN)
GENERAL DESCRIPTION
The ADM1485 is a differential line transceiver suitable for high
speed bidirectional data communication on multipoint bus
transmission lines. It is designed for balanced data transmission
and complies with both EIA Standards RS-485 and RS-422.
The part contains a differential line driver and a differential line
receiver. Both the driver and the receiver may be enabled independently. When disabled, the outputs are tristated.
The ADM1485 operates from a single +5 V power supply.
Excessive power dissipation caused by bus contention or by
output shorting is prevented by a thermal shutdown circuit.
This feature forces the driver output into a high impedance state
if during fault conditions a significant temperature increase is
detected in the internal driver circuitry.
Up to 32 transceivers may be connected simultaneously on a
bus, but only one driver should be enabled at any time. It is
important therefore that the remaining disabled drivers do not
load the bus. To ensure this, the ADM1485 driver features high
output impedance when disabled and also when powered down.
+5 V Low Power
EIA RS-485 Transceiver
ADM1485
FUNCTIONAL BLOCK DIAGRAM
8-Lead
ADM1485
RO
R
VCC
RE
B
DE
A
DI
D
GND
This minimizes the loading effect when the transceiver is not
being utilized. The high impedance driver output is maintained
over the entire common-mode voltage range from –7 V to +12 V.
The receiver contains a fail safe feature which results in a logic
high output state if the inputs are unconnected (floating).
The ADM1485 is fabricated on BiCMOS, an advanced mixed
technology process combining low power CMOS with fast
switching bipolar technology. All inputs and outputs contain
protection against ESD; all driver outputs feature high source
and sink current capability. An epitaxial layer is used to guard
against latch-up.
The ADM1485 features extremely fast switching speeds. Minimal driver propagation delays permit transmission at data rates
up to 30 Mbits/s while low skew minimizes EMI interference.
The part is fully specified over the commercial and industrial
temperature range and is available in an 8-lead DIL/SOIC
package.
REV. A
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
World Wide Web Site: http://www.analog.com
Fax: 781/326-8703
© Analog Devices, Inc., 2000
ADM1485–SPECIFICATIONS (V
Parameter
Min
CC
= +5 V 5%. All specifications TMIN to TMAX unless otherwise noted.)
Typ
DRIVER
Differential Output Voltage, VOD
VOD3
∆|VOD| for Complementary Output States
Common-Mode Output Voltage VOC
∆|VOD| for Complementary Output States
Output Short Circuit Current (VOUT = High)
Output Short Circuit Current (VOUT = Low)
CMOS Input Logic Threshold Low, VINL
CMOS Input Logic Threshold High, VINH
Logic Input Current (DE, DI)
RECEIVER
Differential Input Threshold Voltage, VTH
Input Voltage Hysteresis, ∆VTH
Input Resistance
Input Current (A, B)
Logic Enable Input Current (RE)
CMOS Output Voltage Low, VOL
CMOS Output Voltage High, VOH
Short Circuit Output Current
Tristate Output Leakage Current
2.0
1.5
1.5
35
35
Max
Unit
Test Conditions/Comments
5.0
5.0
5.0
5.0
0.2
3
0.2
250
250
0.8
V
V
V
V
V
V
V
mA
mA
V
V
µA
R = ∞, Figure 1
VCC = 5 V, R = 50 Ω (RS-422), Figure 1
R = 27 Ω (RS-485), Figure 1
VTST = –7 V to +12 V, Figure 2
R = 27 Ω or 50 Ω, Figure 1
R = 27 Ω or 50 Ω, Figure 1
R = 27 Ω or 50 Ω
–7 V ≤ VO ≤ +12 V
–7 V ≤ VO ≤ +12 V
–7 V ≤ VCM ≤ +12 V
VCM = 0 V
–7 V ≤ VCM ≤ +12 V
VIN = 12 V
VIN = –7 V
85
± 1.0
V
mV
kΩ
mA
mA
µA
V
V
mA
µA
2.2
1
mA
mA
Outputs Unloaded, Digital Inputs = GND or VCC
Outputs Unloaded, Digital Inputs = GND or VCC
2.0
± 1.0
–0.2
+0.2
70
12
+1
–0.8
±1
0.4
4.0
7
POWER SUPPLY CURRENT
ICC (Outputs Enabled)
ICC (Outputs Disabled)
1.35
0.7
IOUT = +4.0 mA
IOUT = –4.0 mA
VOUT = GND or VCC
0.4 V ≤ VOUT ≤ +2.4 V
Specifications subject to change without notice.
TIMING SPECIFICATIONS (V
CC
= +5 V 5%. All specifications TMIN to TMAX unless otherwise noted.)
Parameter
DRIVER
Propagation Delay Input to Output TPLH, TPHL
Driver O/P to O/P TSKEW
Driver Rise/Fall Time TR, TF
Driver Enable to Output Valid
Driver Disable Timing
RECEIVER
Propagation Delay Input to Output TPLH, TPHL
Skew |TPLH–TPHL|
Receiver Enable TEN1
Receiver Disable TEN2
Min
Typ
Max
Unit
Test Conditions/Comments
2
10
0
2
10
10
15
5
10
25
25
ns
ns
ns
ns
ns
RL Diff = 54 Ω CL1 = CL2 = 100 pF, Figure 3
RL Diff = 54 Ω CL1 = CL2 = 100 pF, Figure 3
RL Diff = 54 Ω CL1 = CL2 = 100 pF, Figure 3
18
25
0
15
15
40
5
25
25
ns
ns
ns
ns
CL = 15 pF, Figure 5
Figure 6
Figure 6
Specifications subject to change without notice.
–2–
REV. A
ADM1485
PIN FUNCTION DESCRIPTION
ABSOLUTE MAXIMUM RATINGS*
(TA = +25°C unless otherwise noted)
VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +7 V
Inputs
Driver Input (DI) . . . . . . . . . . . . . . . .–0.3 V to VCC + 0.3 V
Control Inputs (DE, RE) . . . . . . . . . . –0.3 V to VCC + 0.3 V
Receiver Inputs (A, B) . . . . . . . . . . . . . . . . . –14 V to +14 V
Outputs
Driver Outputs . . . . . . . . . . . . . . . . . . . . . . . –14 V to +14 V
Receiver Output . . . . . . . . . . . . . . . . .–0.5 V to VCC + 0.5 V
Power Dissipation 8-Lead DIP . . . . . . . . . . . . . . . . . 500 mW
θJA, Thermal Impedance . . . . . . . . . . . . . . . . . . +130°C/W
Power Dissipation 8-Lead SOIC . . . . . . . . . . . . . . . . 450 mW
θJA, Thermal Impedance . . . . . . . . . . . . . . . . . . +170°C/W
Power Dissipation 8-Lead Cerdip . . . . . . . . . . . . . . . 500 mW
θJA, Thermal Impedance . . . . . . . . . . . . . . . . . . +125°C/W
Operating Temperature Range
Commercial (J Version) . . . . . . . . . . . . . . . . . 0°C to +70°C
Industrial (A Version) . . . . . . . . . . . . . . . . –40°C to +85°C
Storage Temperature Range . . . . . . . . . . . –65°C to +150°C
Lead Temperature (Soldering, 10 sec) . . . . . . . . . . . . +300°C
Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . . . +215°C
Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . . . +220°C
Pin Mnemonic Function
1
RO
2
RE
3
DE
4
DI
5
6
GND
A
7
8
B
VCC
*Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those listed in the operational
sections of this specification is not implied. Exposure to absolute maximum ratings
for extended periods of time may affect device reliability.
Receiver Output. When enabled if A > B
by 200 mV, then RO = High. If A < B by
200 mV, then RO = Low.
Receiver Output Enable. A low level enables
the receiver output, RO. A high level places
it in a high impedance state.
Driver Output Enable. A high level enables
the driver differential outputs, A and B. A
low level places it in a high impedance state.
Driver Input. When the driver is enabled a
logic Low on DI forces A low and B high
while a logic High on DI forces A high and
B low.
Ground Connection, 0 V.
Noninverting Receiver Input A/Driver
Output A.
Inverting Receiver Input B/Driver Output B.
Power Supply, 5 V ± 5%.
PIN CONFIGURATION
RO 1
RE 2
VCC
B
TOP VIEW
DE 3 (Not to Scale) 6 A
Table I. Transmitting
RE
INPUTS
DE
DI
OUTPUTS
B
A
X
X
X
1
1
0
1
0
X
0
1
Z
INPUTS
DI 4
1
0
Z
Table II. Receiving
RE
DE
A-B
OUTPUT
RO
0
0
0
1
0
0
0
0
≥ +0.2 V
≤ –0.2 V
Inputs Open
X
1
0
1
Z
7
5
GND
ORDERING GUIDE
Model
Temperature
Range
Package
Option
ADM1485JN
ADM1485JR
ADM1485AN
ADM1485AR
ADM1485AQ
0°C to +70°C
0°C to +70°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
N-8
SO-8
N-8
SO-8
Q-8
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although
the ADM1485 features proprietary ESD protection circuitry, permanent damage may occur on
devices subjected to high-energy electrostatic discharges. Therefore, proper ESD precautions are
recommended to avoid performance degradation or loss of functionality.
REV. A
8
ADM1485
–3–
WARNING!
ESD SENSITIVE DEVICE
ADM1485
Test Circuits
VCC
A
R
RL
R
S2
S1
0V OR 3V
VOD
DE
VOC
CL
B
VOUT
DE IN
Figure 4. Driver Enable/Disable Test Circuit
Figure 1. Driver Voltage Measurement Test Circuit
375
A
VOD3
60
VTST
VOUT
RE
B
CL
375
Figure 2. Driver Voltage Measurement Test Circuit 2
Figure 5. Receiver Propagation Delay Test Circuit
VCC
+1.5V
A
S1
CL1
RL
S2
–1.5V
RLDIFF
RE
CL
CL2
B
VOUT
RE IN
Figure 3. Driver Propagation Delay Test Circuit
Figure 6. Receiver Enable/Disable Test Circuit
Switching Characteristics
3V
1.5V
0V
1.5V
TPLH
A, B
0V
0V
TPLH
TPHL
TPHL
B
1/2VO
VO
VOH
A
TSKEW
VO
TSKEW
RO
1.5V
1.5V
90% POINT
90% POINT
0V
–VO
VOL
10% POINT
10% POINT
Figure 9. Receiver Propagation Delay
TF
TR
Figure 7. Driver Propagation Delay, Rise/Fall Timing
3V
3V
DE
1.5V
RE
1.5V
1.5V
0V
0V
TZL
TZL
TLZ
TLZ
1.5V
R
2.3V
A, B
1.5V
VOL
TZH
THZ
TZH
VOL
THZ
O/P HIGH
VOH
A, B
VOL +0.5V
O/P LOW
VOL +0.5V
VOH –0.5V
R
2.3V
0V
1.5V
VOH
VOH –0.5V
0V
Figure 8. Driver Enable/Disable Timing
Figure 10. Receiver Enable/Disable Timing
–4–
REV. A
0
36
–2
32
–4
28
24
20
16
12
8
I = 8mA
–6
–8
–10
–12
–14
–16
4
0
5.0
OUTPUT VOLTAGE – Volts
40
OUTPUT CURRENT – mA
OUTPUT CURRENT – mA
Typical Performance Characteristics–ADM1485
4.9
4.8
4.7
4.6
–18
0
0.5
1.0
1.5
OUTPUT VOLTAGE – Volts
–20
3.5
2.0
Figure 11. Receiver Output Low
Voltage vs. Output Current
4.0
4.5
OUTPUT VOLTAGE – Volts
4.5
–50
5.0
Figure 12. Receiver Output High
Voltage vs. Output Current
0.4
–25
0
25
50
75
TEMPERATURE – C
100
125
Figure 13. Receiver Output High
Voltage vs. Temperature
96
2.4
I = 8mA
0.3
0.2
DIFFERENTIAL VOLTAGE – Volts
OUTPUT CURRENT – mA
OUTPUT VOLTAGE – Volts
84
72
60
48
36
24
12
0.1
–50
–25
0
25
50
75
TEMPERATURE – C
100
Figure 14. Receiver Output Low
Voltage vs. Temperature
0
1
2
3
OUTPUT VOLTAGE – Volts
2.2
2.1
2.0
–50
4
Figure 15. Driver Differential Output Voltage vs. Output Current
1.00
90
–10
0.95
80
–20
60
50
40
30
–30
–40
–50
–60
–70
20
–80
10
–90
0
0
1
2
3
OUTPUT VOLTAGE – Volts
Figure 17. Driver Output Low
Voltage vs. Output Current
REV. A
4
SUPPLY CURRENT – mA
0
70
–100
–25
0
25
50
75
TEMPERATURE – C
100
125
Figure 16. Driver Differential Output
Voltage vs. Temperature, RL = 54 Ω
100
OUTPUT CURRENT – mA
OUTPUT CURRENT – mA
0
125
2.3
0.90
DRIVER ENABLED
0.85
0.80
0.75
DRIVER DISABLED
0.70
0.65
0
1
2
3
4
OUTPUT VOLTAGE – Volts
Figure 18. Driver Output High
Voltage vs. Output Current
–5–
5
0.60
–50
–25
0
25
50
75
TEMPERATURE – C
100
Figure 19. Supply Current vs.
Temperature
125
ADM1485–Typical Performance Characteristics
1.0
5
0.9
4
100
90
TIME – ns
TIME – ns
0.8
3
2
0.7
0.6
10
1
0%
0.5
1V
0
–50
–25
0
25
50
75
TEMPERATURE – C
100
0.4
–50
125
Figure 20. Receiver tPLH–tPHL vs.
Temperature
–25
0
25
50
75
TEMPERATURE – C
100
100
90
90
Figure 22. Unloaded Driver
Differential Outputs
100
90
10
10
10
0%
0%
0%
500mV
500mV
1V
5ns
Figure 23. Loaded Driver
Differential Outputs
5ns
125
Figure 21. Driver Skew vs.
Temperature
100
1V
1V
5
5 10ns
1V
HO
Figure 24. Driver/Receiver Propagation Delays Low to High
RT
1V
5
5 10ns
HO
Figure 25. Driver/Receiver Propagation Delays High to Low
RT
D
D
R
R
R
R
D
D
Figure 26. Typical RS-485 Network
–6–
REV. A
ADM1485
showing a multipoint transmission network is illustrated in
Figure 26. An RS-485 transmission line can have as many as 32
transceivers on the bus. Only one driver can transmit at a particular time but multiple receivers may be enabled simultaneously.
APPLICATIONS INFORMATION
Differential Data Transmission
Differential data transmission is used to reliably transmit data at
high rates over long distances and through noisy environments.
Differential transmission nullifies the effects of ground shifts and
noise signals which appear as common-mode voltages on the
line. There are two main standards approved by the Electronics
Industries Association (EIA) which specify the electrical characteristics of transceivers used in differential data transmission.
As with any transmission line, it is important that reflections are
minimized. This may be achieved by terminating the extreme
ends of the line using resistors equal to the characteristic impedance of the line. Stub lengths of the main line should also be
kept as short as possible. A properly terminated transmission
line appears purely resistive to the driver.
The RS-422 standard specifies data rates up to 10 MBaud and
line lengths up to 4000 ft. A single driver can drive a transmission line with up to 10 receivers.
Thermal Shutdown
The ADM1485 contains thermal shutdown circuitry which
protects the part from excessive power dissipation during fault
conditions. Shorting the driver outputs to a low impedance
source can result in high driver currents. The thermal sensing
circuitry detects the increase in die temperature and disables the
driver outputs. The thermal sensing circuitry is designed to
disable the driver outputs when a die temperature of 150°C is
reached. As the device cools, the drivers are re-enabled at
140°C.
In order to cater for true multipoint communications, the
RS-485 standard was defined. This standard meets or exceeds
all the requirements of RS-422 but also allows for up to 32
drivers and 32 receivers to be connected to a single bus. An
extended common-mode range of –7 V to +12 V is defined. The
most significant difference between RS-422 and RS-485 is the
fact that the drivers may be disabled thereby allowing more than
one (32 in fact) to be connected to a single line. Only one driver
should be enabled at time, but the RS-485 standard contains
additional specifications to guarantee device safety in the event
of line contention.
Propagation Delay
The ADM1485 features very low propagation delay ensuring
maximum baud rate operation. The driver is well balanced
ensuring distortion free transmission.
Cable and Data Rate
The transmission line of choice for RS-485 communications is a
twisted pair. Twisted pair cable tends to cancel common-mode
noise and also causes cancellation of the magnetic fields generated by the current flowing through each wire, thereby, reducing
the effective inductance of the pair.
Another important specification is a measure of the skew between the complementary outputs. Excessive skew impairs the
noise immunity of the system and increases the amount of electromagnetic interference (EMI).
The ADM1485 is designed for bidirectional data communications on multipoint transmission lines. A typical application
The receiver input includes a fail-safe feature which guarantees
a logic high on the receiver when the inputs are open circuit or
floating.
Receiver Open-Circuit Fail Safe
Table III. Comparison of RS-422 and RS-485 Interface Standards
REV. A
Specification
RS-422
RS-485
Transmission Type
Maximum Cable Length
Minimum Driver Output Voltage
Driver Load Impedance
Receiver Input Resistance
Receiver Input Sensitivity
Receiver Input Voltage Range
No of Drivers/Receivers Per Line
Differential
4000 ft.
±2 V
100 Ω
4 kΩ min
± 200 mV
–7 V to +7 V
1/10
Differential
4000 ft.
± 1.5 V
54 Ω
12 kΩ min
± 200 mV
–7 V to +12 V
32/32
–7–
ADM1485
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
C1818–0–6/00 (rev. A) 00063
8-Lead SOIC (SO-8)
0.1968 (5.00)
0.1890 (4.80)
0.1574 (4.00)
0.1497 (3.80)
8
5
1
4
0.2440 (6.20)
0.2284 (5.80)
PIN 1
0.0196 (0.50)
45
0.0099 (0.25)
0.0500 (1.27)
BSC
0.0688 (1.75)
0.0532 (1.35)
0.0098 (0.25)
0.0040 (0.10)
8
0.0500 (1.27)
0.0098 (0.25) 0
0.0160 (0.41)
0.0075 (0.19)
0.0192 (0.49)
0.0138 (0.35)
SEATING
PLANE
8-Lead Plastic DIP (N-8)
0.430 (10.92)
0.348 (8.84)
8
5
1
0.280 (7.11)
0.240 (6.10)
4
0.325 (8.25)
0.300 (7.62)
PIN 1
0.100 (2.54)
BSC
0.060 (1.52)
0.015 (0.38)
0.210
(5.33)
MAX
0.195 (4.95)
0.115 (2.93)
0.130
(3.30)
MIN
0.160 (4.06)
0.115 (2.93)
0.015 (0.381)
0.008 (0.204)
0.022 (0.558) 0.070 (1.77) SEATING
0.014 (0.356) 0.045 (1.15) PLANE
8-Lead Cerdip (Q-8)
0.005 (0.13)
MIN
0.055 (1.4)
MAX
8
5
0.310 (7.87)
0.220 (5.59)
1
4
PIN 1
0.200 (5.08)
MAX
0.320 (8.13)
0.290 (7.37)
0.060 (1.52)
0.015 (0.38)
0.200 (5.08)
0.125 (3.18)
0.023 (0.58) 0.100 0.070 (1.78)
0.014 (0.36) (2.54) 0.030 (0.76)
BSC
PRINTED IN U.S.A.
0.405 (10.29)
MAX
0.150
(3.81)
MIN
SEATING
PLANE
–8–
15°
0°
0.015 (0.38)
0.008 (0.20)
REV. A