UG06A THRU UG06D MINIATURE ULTRAFAST EFFICIENT PLASTIC RECTIFIER Reverse Voltage - 50 to 200 Volts FEATURES Case Style MPG06 0.100 (2.54) Forward Current - 0.6 Ampere 1.0 (25.4) MIN. 0.090 (2.29) DIA 0.125 (3.18) 0.115 (2.92) ♦ Plastic package has Underwriters Laboratories Flammability Classification 94V-0 ♦ Ideally suited for use in very high frequency switching power supplies, inverters and as a free wheeling diode ♦ Ultrafast reverse recovery times for high efficiency ♦ Soft recovery characteristics ♦ Excellent high temperature switching ♦ Glass passivated junction ♦ High temperature soldering guaranteed: 250°C/10 seconds, 0.375" (9.5mm) lead length, 5 lbs. (2.3kg) tension 1.0 (25.4) MIN. MECHANICAL DATA 0.025 (0.635) 0.023 (0.584) DIA. Dimensions in inches and (millimeters) Case: Void free molded plastic body over passivated chip Terminals: Plated axial leads, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting Position: Any WeIght: 0.0064 ounce, 0.181 gram MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS UG06A UG06B UG06C UG06D UNITS Maximum repetitive peak reverse voltage VRRM 50 100 150 200 Volts Maximum RMS voltage VRMS 35 70 105 140 Volts Maximum DC blocking voltage VDC 50 100 150 200 Volts Maximum average forward rectified current 0.375" (9.5mm) lead length at TL=75°C I(AV) 0.6 Amp Peak forward surge current 8.3 ms single half sine-wave superimposed on rated load (JEDEC Method) at TL=75°C IFSM 40.0 Amps VF 0.95 Volts IR 5.0 100.0 µA trr 15.0 ns TJ=25°C TJ=100°C trr 25.0 35.0 ns TJ=25°C TJ=100°C Qrr 8.0 20.0 nC CJ 9.0 pF RΘJA RΘJL 97.0 28.0 °C/W TJ, TSTG -55 to +150 °C Maximum instantaneous forward voltage at 0.6A Maximum DC reverse current at rated DC blocking voltage TA=25°C TA=100°C Maximum reverse recovery time (NOTE 1) Maximum reverse recovery time (NOTE 2) Maximum recovered stored charge (NOTE 2) Typical junction capacitance (NOTE 3) Typical thermal resistance (NOTE 4) Operating junction and storage temperature range NOTES: (1) Reverse recovery test conditions: IF=0.5A, IR=1.0A,Irr=0.25A (2) trr and Qrr measured at IF=0.6A: VR=30V, di/dt=50A/µs, Irr=10% IRM for meaurement of trr (3) Measured at 1.0 MHZ and applied reverse voltage of 4.0 Volts (4) Thermal resistance from junction to ambient and junction to lead at 0.375" (9.5mm) lead length P.C.B. mounted with 0.2 x 0.2” (5.0 x 5.0mm) copper pads 4/98 RATINGS AND CHARACTERISTIC CURVES UG06A THRU UG06D FIG. 1 - MAXIMUM FORWARD CURRENT DERATING CURVES 100 RESISTIVE OR INDUCTIVE LOAD 0.375" (9.5mm) LEAD LENGTH PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD RECTIFIED CURRENT, AMPERES 0.9 FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 0.75 TL, LEAD TEMPERATURE 0.6 TA, AMBIENT TEMPERATURE P.C.B. MOUNTED 0.2 x 0.2" (5.0 x 5.0mm) COPPER PADS 0.45 0.3 0.15 TJ=75°C 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 10 1 0 0 25 50 75 100 125 150 1 10 175 100 NUMBER OF CYCLES AT 60 HZ 100 TJ=100°C 10 TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE 1 0.1 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 INSTANTANEOUS FORWARD VOLTAGE, VOLTS FIG. 4 - TYPICAL REVERSE LEAKAGE CHARACTERISTICS 1,000 100 TJ=25°C 1 0.1 0.01 0 20 40 60 FIG. 6 - TYPICAL JUNCTION CAPACITANCE JUNCTION CAPACITANCE, pF trr Qrr 50 40 di/dt=20A/µs di/dt=50A/µs 30 di/dt=100A/µs di/dt=150A/µs 20 di/dt=150A/µs di/dt=100A/µs 10 TJ=25°C f=1.0 MHZ Vsig=50mVp-p 10 1 0.1 di/dt=50A/µs di/dt=20A/µs 1 10 REVERSE VOLTAGE, VOLTS 25 100 100 IF=0.6A VR=30V 0 80 PERCENT OF RATED PEAK REVERSE VOLTAGE, % 60 0 TJ=100°C 10 FIG. 5 - REVERSE SWITCHING CHARACTERISTICS RECOVERED pP CHARGE/REVERSE RECOVERY TIME, nC/ns INSTANTANEOUS FORWARD CURRENT, AMPERES FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS INSTANTANEOUS REVERSE LEAKAGE CURRENT, MICROAMPERES TEMPERATURE, °C 50 75 100 125 150 JUNCTION TEMPERATURE °C 175 100