TI CL10A226MQ8NRNC 3-mhz 2a step down converter in 2x2 son package Datasheet

TPS62065, TPS62067
www.ti.com
SLVS833 – MARCH 2010
3-MHz 2A Step Down Converter in 2x2 SON Package
Check for Samples: TPS62065, TPS62067
FEATURES
1
•
•
•
•
•
•
•
•
•
•
•
•
•
2
DESCRIPTION
3 MHz Switching Frequency
VIN Range from 3.0V to 6V
Up to 97% Efficiency
Power Save Mode / 3MHz Fixed PWM Mode
Power Good Output
Output Voltage Accuracy in PWM Mode ±1.5%
Output Capacitor Discharge Function
Typical 18 µA Quiescent Current
100% Duty Cycle for Lowest Dropout
Voltage Positioning
Clock Dithering
Supports Maximum 1mm Height Solutions
Available in a 2x2x0.75mm SON
The TPS6206x is a family of highly efficient
synchronous step down DC-DC converters. They
provide up to 2.0A output current.
With an input voltage range of 3.0V to 6V the device
is a perfect fit for power conversion from a 5V or 3.3V
system supply rail. The TPS6206x operates at 3MHz
fixed frequency and enters Power Save Mode
operation at light load currents to maintain high
efficiency over the entire load current range. The
Power Save Mode is optimized for low output voltage
ripple. For low noise applications, TPS62065 can be
forced into fixed frequency PWM mode by pulling the
MODE pin high. TPS62067 provides an open drain
power good output.
In the shutdown mode, the current consumption is
reduced to less than 1µA and an internal circuit
discharges the output capacitor.
APPLICATIONS
•
•
•
•
POL
Notebooks, Pocket PCs
Portable Media Players
DSP Supply
TPS6206x family is optimized for operation with a tiny
1.0µH inductor and a small 10µF output capacitor to
achieve smallest solution size and high regulation
performance.
The TPS6206X is available in a small 2x2x0.75mm
8-pin SON package.
100
TYPICAL APPLICATION CIRCUIT
VIN = 3.7 V
95
90
VIN = 3 V to 6 V
PVIN
L
1.0 mH
SW
AVIN
CIN
10 mF
R1
360 kW
EN
FB
R2
180 kW
AGND
PGND
VOUT
1.8 V 2 A
Cff
22 pF
COUT
10 mF
RPG
100 kW
VIN = 4.2 V
85
Efficiency - %
TPS62067
VIN = 5 V
80
75
70
65
L = 1.2 mH (NRG4026T 1R2),
COUT = 22 mF (0603 size),
VOUT = 3.3 V,
Mode: Auto PFM/PWM
PG
60
55
50
0
0.25
0.5
0.75
1
1.25 1.5
IL - Load Current - A
1.75
2
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PowerPAD is a trademark of Texas Instruments.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2010, Texas Instruments Incorporated
TPS62065, TPS62067
SLVS833 – MARCH 2010
www.ti.com
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
ORDERING INFORMATION (1)
–40°C to
85°C
(1)
(2)
(3)
FUNCTION
Power Good
(PG)
MAXIMUM
OUTPUT
CURRENT
PACKAGE
DESIGNATOR
ORDERING (3)
Selectable
No
2.0 A
DSG
TPS62065DSG
OFA
Auto
PWM/PFM
Yes
2.0 A
DSG
TPS62067DSG
ODH
PART
NUMBER
OUTPUT
VOLTAGE (2)
MODE
TPS62065
Adjustable
TPS62067
Adjustable
TA
PACKAGE
MARKING
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
website at www.ti.com.
Contact TI for other fixed output voltage options
The DSG (SON-8) packages is available in tape on reel. Add R suffix to order quantities of 3000 parts per reel.
ABSOLUTE MAXIMUM RATINGS
over operating free-air temperature range (unless otherwise noted) (1)
VALUE
UNIT
MIN
Voltage Range
(2)
AVIN, PVIN
EN, MODE, PG, FB
–0.3
7
–0.3 to
VIN +0.3 < 7
–0.3
7
SW
Current (sink)
into PG
Current (source)
Peak output
MAX
1
A
Electrostatic Discharge (HBM) QSS 009-105 (JESD22-A114A) (3)
2
Electrostatic Discharge (CDM) QSS 009-147 (JESD22-C101B.01)
1
Temperature
(1)
(2)
(3)
mA
Internally limited
Electrostatic Discharge (Machine model)
V
kV
200
V
TJ
–40
125
°C
Tstg
–65
150
°C
Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltage values are with respect to network ground terminal.
The human body model is a 100-pF capacitor discharged through a 1.5-kΩ resistor into each pin. The machine model is a 200-pF
capacitor discharged directly into each pin.
DISSIPATION RATINGS (1) (2)
(1)
(2)
2
PACKAGE
RqJA
POWER RATING
TA = ≤ 25°C
DERATING FACTOR
ABOVE TA = 25°C
DSG
75°C/W
1300 mW
13 mW/°C
Maximum power dissipation is a function of TJ(max), qJA and TA. The maximum allowable power dissipation at any allowable ambient
temperature is PD = (TJ(max) – TA)/ qJA.
This thermal data measured with high-K board (4 layers according to JESD51-7 JEDEC Standard).
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s) :TPS62065 TPS62067
TPS62065, TPS62067
www.ti.com
SLVS833 – MARCH 2010
RECOMMENDED OPERATING CONDITIONS
MIN
AVIN ,
PVIN
Supply voltage
NOM
MAX
3.0
6
Output current capability
2000
Output voltage range for adjustable voltage
0.8
L
Effective Inductance Range
0.7
COUT
Effective Output Capacitance Range
4.5
TA
Operating ambient temperature (1)
–40
TJ
Operating junction temperature
–40
(1)
UNIT
V
mA
VIN
V
1.0
1.6
µH
10
22
µF
85
°C
125
°C
In applications where high power dissipation and/or poor package thermal resistance is present, the maximum ambient temperature may
have to be derated. Maximum ambient temperature (TA(max)) is dependent on the maximum operating junction temperature (TJ(max)), the
maximum power dissipation of the device in the application (PD(max)), and the junction-to-ambient thermal resistance of the
part/package in the application (qJA), as given by the following equation: TA(max)= TJ(max)–(qJA X PD(max))
ELECTRICAL CHARACTERISTICS
Over full operating ambient temperature range, typical values are at TA = 25°C. Unless otherwise noted, specifications apply
for condition VIN = EN = 3.6V. External components CIN = 10mF 0603, COUT = 10mF 0603, L = 1.0mH, see the parameter
measurement information.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
SUPPLY
VIN
Input voltage range
3.0
IQ
Operating quiescent current
IOUT = 0 mA, device operating in PFM mode
and not device not switching
ISD
Shutdown current
EN = GND, current into AVIN and PVIN combined
VUVLO
Undervoltage lockout threshold
6
18
V
mA
0.1
1
Falling
1.73
1.78
1.83
Rising
1.9
1.95
1.99
mA
V
ENABLE, MODE
VIH
High level input voltage
3.0 V ≤ VIN ≤ 6 V
1.0
6
V
VIL
Low level input voltage
3.0 V ≤ VIN ≤ 6 V
0
0.4
V
IIN
Input bias current
EN, Mode tied to GND or AVIN
0.01
1
mA
POWER GOOD OPEN DRAIN OUTPUT
Rising feedback voltage
93%
95%
98%
Falling feedback voltage
87%
90%
92%
VTHPG
Power good threshold voltage
VOL
Output low voltage
IOUT = –1mA; must be limited by external pullup
resistor (1)
0.3
VH
Output high voltage
Voltage applied to PG pin via external pullup
resistor
VIN
V
ILKG
Leakage current into PG pin
V(PG) = 3.6V
100
nA
tPGDL
Internal power good delay time
5
V
µs
POWER SWITCH
VIN = 3.6 V
(1)
120
180
(1)
95
150
VIN = 3.6 V (1)
90
130
(1)
75
100
2750
3300
RDS(on)
High-side MOSFET on-resistance
RDS(on)
Low-side MOSFET on-resistance
ILIMF
Forward current limit MOSFET
high-side and low-side
3V ≤ VIN ≤ 3.6 V
Thermal shutdown
Increasing junction temperature
150
Thermal shutdown hysteresis
Decreasing junction temperature
10
TSD
(1)
VIN = 5.0 V
VIN = 5.0 V
2300
mΩ
mΩ
mA
°C
Maximum value applies for TJ = 85°C
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s) :TPS62065 TPS62067
3
TPS62065, TPS62067
SLVS833 – MARCH 2010
www.ti.com
ELECTRICAL CHARACTERISTICS (continued)
Over full operating ambient temperature range, typical values are at TA = 25°C. Unless otherwise noted, specifications apply
for condition VIN = EN = 3.6V. External components CIN = 10mF 0603, COUT = 10mF 0603, L = 1.0mH, see the parameter
measurement information.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
2.6
3
3.4
MHz
OSCILLATOR
fSW
3.0 V ≤ VIN ≤ 6 V
Oscillator frequency
OUTPUT
Vref
Reference voltage
600
VFB(PWM)
Feedback voltage PWM Mode
VFB(PFM)
Feedback voltage PFM mode,
Voltage Positioning
PWM operation, MODE = VIN ,
3.0 V ≤ VIN ≤ 6 V, 0 mA load
–1.5
1
-0.5
Line regulation
%/A
0
R(Discharge)
Internal discharge resistor
Activated with EN = GND, 3.0V ≤ VIN≤ 6V, 0.8 ≤
VOUT≤ 3.6V
tSTART
Start-up time
Time from active EN to reach 95% of VOUT
(2)
1.5
%
device in PFM mode, voltage positioning active (2)
Load regulation
VFB
0
mV
75
200
%/V
1450
500
Ω
ms
In PFM mode, the internal reference voltage is set to typ. 1.01×Vref. See the parameter measurement information.
PIN ASSIGNMENTS
TERMINAL FUNCTIONS
TERMINAL
NO.
SON 2x2-8
I/O
PGND
1
PWR
GND supply pin for the output stage.
SW
2
OUT
This is the switch pin and is connected to the internal MOSFET switches. Connect the
external inductor between this terminal and the output capacitor.
AGND
3
IN
Analog GND supply pin for the control circuit.
FB
4
IN
Feedback pin for the internal regulation loop. Connect the external resistor divider to this pin.
In case of fixed output voltage option, connect this pin directly to the output capacitor
EN
5
IN
This is the enable pin of the device. Pulling this pin to low forces the device into shutdown
mode. Pulling this pin to high enables the device. This pin must be terminated
IN
MODE: MODE pin = high forces the device to operate in fixed frequency PWM mode. MODE
pin = low enables the Power Save Mode with automatic transition from PFM mode to fixed
frequency PWM mode.
NAME
MODE
6
Open
Drain
PG
AVIN
7
IN
PVIN
8
PWR
Power PAD
4
DESCRIPTION
PG: Power Good Open Drain output. Connect an external pull up resistor to a rail which is
below or equal AVIN.
Analog VIN power supply for the control circuit. Need to be connected to PVIN and input
capacitor.
VIN power supply pin for the output stage.
For good thermal performance, this PAD must be soldered to the land pattern on the pcb.
This PAD should be used as device GND.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s) :TPS62065 TPS62067
TPS62065, TPS62067
www.ti.com
SLVS833 – MARCH 2010
FUNCTIONAL BLOCK DIAGRAM
AVIN
PVIN
Current
Limit Comparator
Undervoltage
Lockout 1.8V
Thermal
Shutdown
Limit
High Side
PFM Comparator
Reference
0.6V VREF
FB
VREF
Softstart
VOUT RAMP
CONTROL
Gate Driver
Anti
Shoot-Through
Control
Stage
Error Amp.
VREF
SW1
Integrator
FB
PWM
Comp.
Zero-Pole
AMP.
Internal
FB
Network*
Limit
Low Side
MODE *
Sawtooth
Generator
3MHz
Clock
Current
Limit Comparator
PG
MODE/
PG
FB
VREF
RDischarge
PG Comparator*
EN
AGND
PGND
* Function depends on device option
Vertical spacer
Vertical spacer
PARAMETER MEASUREMENT INFORMATION
VIN = 3 V to 6 V
TPS6206X
PVIN
CIN
10 µF
L
1.0 µH/1.2 µH
VOUT
up to 2.0 A
SW
AVIN
EN
MODE/PG FB
AGND
PGND
R1
COUT
Cff
22 pF 10 µF
R2
L: LQH44PN1R0NP0, L = 1.0 mH,Murata,
NRG4026T1R2, L = 1.2 mH, Taiyo Yuden
CIN/COUT: GRM188R60J106U, Murata 0603 size
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s) :TPS62065 TPS62067
5
TPS62065, TPS62067
SLVS833 – MARCH 2010
www.ti.com
TYPICAL CHARACTERISTICS
Table 1. Table of Graphs
FIGURE
h
Load Current, VOUT = 1.2 V, Auto PF//PWM Mode, Linear Scale
Figure 1
Load Current, VOUT = 1.8 V, Auto PFM/PWM Mode, Linear Scale
Figure 2
Load Current, VOUT = 3.3 V, PFM/PWM Mode, Linear Scale
Figure 3
Load Current, VOUT = 1.8 V, Auto PFM/PWM Mode vs. Forced PWM
Mode, Logarithmic Scale
Figure 4
Load Current, VOUT = 1.8 V, Auto PFM/PWM Mode
Figure 5
Load Current, VOUT = 1.8 V, Forced PWM Mode
Figure 6
Shutdown Current
Input Voltage and Ambient Temperature
Figure 7
Quiescent Current
Input Voltage
Figure 8
Oscillator Frequency
Input Voltage
Figure 9
Static Drain-Source On-State
Resistance
Input Voltage, Low-Side Switch
Figure 10
Input Voltage, High-Side Switch
Figure 11
RDISCHARGE
Input Voltage vs. VOUT
Figure 12
PWM Mode, VIN = 3.6 V, VOUT = 1.8 V, 500 mA, L = 1.2 mH, COUT = 10mF
Figure 13
PFM Mode, VIN = 3.6 V, VOUT = 1.8 V, 20 mA, L = 1.2 mH, COUT = 10mF
Figure 14
PWM Mode, VIN = 3.6 V, VOUT = 1.2 V, 0.2 mA to 1 A
Figure 15
PFM Mode, VIN = 3.6 V, VOUT = 1.2 V, 20 mA to 250 mA
Figure 16
VIN = 3.6 V, VOUT = 1.8 V, 200 mA to 1500 mA
Figure 17
PWM Mode, VIN = 3.6 V to 4.2 V, VOUT = 1.8 V, 500 mA
Figure 18
PFM Mode, VIN = 3.6 V to 4.2 V, VOUT = 1.8 V, 500 mA
Figure 19
Startup into Load
VIN = 3.6 V, VOUT = 1.8 V, Load = 2.2-Ω
Figure 20
Startup TPS62067
Into 2.2-Ω Load with Power Good
Figure 21
Output Discharge
VIN = 3.6 V, VOUT = 1.8 V, No Load
Figure 22
Shutdown TPS62067
VIN = 4.2 V, VOUT = 3.3 V, No Load, PG Pullup Resistor 10 kΩ
Figure 23
Efficiency
Output Voltage Accuracy
Typical Operation
Load Transient
Line Transient
6
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s) :TPS62065 TPS62067
TPS62065, TPS62067
www.ti.com
SLVS833 – MARCH 2010
EFFICIENCY
vs
LOAD CURRENT
EFFICIENCY
vs
LOAD CURRENT
100
100
95
95
90
80
VIN = 3 V
75
VIN = 3.3 V
VIN = 3.6 V
70
65
VIN = 3 V
80
VIN = 3.3 V
75
VIN = 3.6 V
70
65
L = 1.2 mH (NRG4026T 1R2),
COUT = 10 mF (0603 size),
VOUT = 1.2 V,
Mode: Auto PFM/PWM
60
55
50
0
0.25
0.5
0.75
1
1.25 1.5
IL - Load Current - A
1.75
L = 1.2 mH (NRG4026T 1R2),
COUT = 10 mF (0603 size),
VOUT = 1.8 V,
Mode: Auto PFM/PWM
60
55
50
0
2
0.25
0.5
0.75
1
1.25 1.5
IL - Load Current - A
1.75
Figure 1. VOUT = 1.2V, Auto PFM/PWM Mode,
Linear Scale
Figure 2. VOUT = 1.8V, Auto PFM/PWM Mode,
Linear Scale
EFFICIENCY
vs
LOAD CURRENT
EFFICIENCY
vs
LOAD CURRENT
100
2
100
VIN = 3.7 V
Auto PFM/PWM Mode
95
90
90
VIN = 4.2 V
80
VIN = 5 V
85
70
Efficiency - %
Efficiency - %
VIN = 5 V
85
VIN = 4.2 V
Efficiency - %
Efficiency - %
85
80
75
70
VIN = 3.3 V
VIN = 3.6 V
VIN = 4.2 V
VIN = 5 V
Forced PWM Mode
60
VIN = 3.3 V
VIN = 3.6 V
VIN = 4.2 V
VIN = 5 V
50
40
30
65
L = 1.2 mH (NRG4026T 1R2),
COUT = 22 mF (0603 size),
VOUT = 3.3 V,
Mode: Auto PFM/PWM
60
55
50
VIN = 4.2 V
90
VIN = 5 V
0
0.25
0.5
0.75
1
1.25 1.5
IL - Load Current - A
1.75
Figure 3. VOUT = 3.3V, Auto PFM/PWM Mode,
Linear Scale
20
L = 1.2 mH (NRG4026T 1R2),
COUT = 10 mF (0603 size),
VOUT = 1.8 V
10
2
0
0.001
0.01
0.1
IL - Load Current - A
1
10
Figure 4. Auto PFM/PWM Mode vs. Forced PWM Mode,
Logarithmic Scale
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s) :TPS62065 TPS62067
7
TPS62065, TPS62067
SLVS833 – MARCH 2010
www.ti.com
OUTPUT VOLTAGE ACCURACY
vs
LOAD CURRENT
1.890
1.890
1.872
1.872
1.854 Voltage Positioning PFM Mode
1.854
VO - Output Voltage DC - V
VO - Output Voltage DC - V
OUTPUT VOLTAGE ACCURACY
vs
LOAD CURRENT
1.836
1.818
1.800
VIN = 3.6 V
VIN = 4.2 V
1.782
1.764
PWM Mode
VIN = 3.3 V
VIN = 5 V
L = 1 mH,
COUT = 10 mF,
VOUT = 1.8 V,
Mode: Auto PFM/PWM
1.746
1.728
1.710
0.001
0.01
0.1
IL - Load Current - A
1
1.836
1.818
1.800
VIN = 3.3 V
1.782
VIN = 3.6 V
VIN = 4.2 V
1.764
VIN = 5 V
1.746
1.728
10
1.710
0.001
0.01
Figure 6. Forced PWM Mode
SHUTDOWN CURRENT
vs
INPUT VOLTAGE AND AMBIENT TEMPERATURE
QUIESCENT CURRENT
vs
INPUT VOLTAGE
10
TA = 85°C
TA = 85°C
20
Iq - Quiesent Current - mA
0.75
0.50
TA = 25°C
0.25
0
2.5
1
25
3
TA = 25°C
15
TA = -40°C
10
5
TA = -40°C
3.5
4
4.5
5
VI - Input Voltage - V
5.5
6
0
2.5
3
Figure 7.
8
0.1
IL - Load Current - A
Figure 5. Auto PFM/PWM Mode
1
ISHDN - Shutdown Current - mA
L = 1 mH,
COUT = 10 mF,
VOUT = 1.8 V,
Mode: Forced PWM
3.5
4
4.5
5
VI - Input Voltage - V
5.5
6
Figure 8.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s) :TPS62065 TPS62067
TPS62065, TPS62067
www.ti.com
SLVS833 – MARCH 2010
OSCILLATOR FREQUENCY
vs
INPUT VOLTAGE
STATIC DRAIN-SOURCE ON-STATE RESISTANCE
vs
INPUT VOLTAGE
0.12
TA = 85°C
3.05
0.1
TJ = 85°C
TA = 25°C
TJ = 25°C
3
0.08
RDSON - W
fOSC - Oscillator Frequency - MHz
3.1
2.95
TA = -40°C
0.06
2.9
0.04
2.85
0.02
2.8
2.5
3
3.5
4
4.5
5
VI - Input Voltage - V
5.5
0
2.5
6
TJ = -40°C
3
3.5
4
4.5
5
VI - Input Voltage - V
Figure 9.
Figure 10. Low-Side Switch
STATIC DRAIN-SOURCE ON-STATE RESISTANCE
vs
INPUT VOLTAGE
RDISCHARGE
vs
INPUT VOLTAGE
0.2
5.5
6
5.5
6
600
0.18
500
0.16
400
TJ = 25°C
0.12
RDischarge - W
RDSON - W
VO = 3.3 V
TJ = 85°C
0.14
TJ = -40°C
0.1
0.08
VO = 1.8 V
300
200
0.06
VO = 1.2 V
0.04
100
0.02
0
2.5
3
3.5
4
4.5
5
VI - Input Voltage - V
5.5
6
0
2.5
3
Figure 11. High-Side Switch
3.5
4
4.5
5
VI - Input Voltage - V
Figure 12.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s) :TPS62065 TPS62067
9
TPS62065, TPS62067
SLVS833 – MARCH 2010
www.ti.com
VOUT 50mV/Div
VOUT 50mV/Div
VIN = 3.6 V
VOUT = 1.8 V
IOUT = 20 mA
MODE = GND
L = 1.2 mH
COUT = 10 mF
SW 2V/Div
SW 2V/Div
ICOIL 500mA/Div
MODE = GND
VIN = 3.6 V
L = 1.2 mH
VOUT = 1.8 V
IOUT = 500 mA COUT = 10 mF
ICOIL 200mA/Div
Time Base - 100ns/Div
Time Base - 4ms/Div
Figure 13. Typical Operation (PWM Mode)
Figure 14. Typical Operation (PFM Mode)
VOUT100 mV/Div
VOUT100 mV/Div
SW 2V/Div
SW 2V/Div
ICOIL1A/Div
ICOIL1A/Div
ILOAD500 mA/Div
VIN = 3.6 V,
VOUT = 1.2 V,
IOUT = 0.2 A to 1 A
MODE = VIN
ILOAD500 mA/Div
Time Base - 10 µs/Div
Time Base - 10 µs/Div
Figure 15. Load Transient Response
PWM Mode 0.2A To 1A
10
VIN = 3.6 V,
VOUT = 1.2 V,
IOUT = 20 mA to 250 mA
Figure 16. Load Transient
PFM Mode 20 mA to 250mA
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s) :TPS62065 TPS62067
TPS62065, TPS62067
www.ti.com
SLVS833 – MARCH 2010
VIN = 3.6 V to 4.2 V,
VOUT = 1.8 V,
IOUT = 500 mA
L = 1.2 mH,
200 mV/Div
500 mV/Div
2A/Div
VIN = 3.6 V,
VOUT = 1.8 V,
50 mV/Div
L = 1.2 mH
COUT = 10 mF
IOUT 200 mA to 1500 mA
1A/Div
Time Base - 100 ms/Div
Time Base - 100ms/Div
Figure 17. Load Transient Response
200 mA To 1500 mA
Figure 18. Line Transient Response PWM Mode
2 V/Div
500 mV/Div
1 V/Div
2 A/Div
500 mA/Div
VIN = 3.6 V to 4.2 V,
VOUT = 1.8 V,
IOUT = 50 mA,
50 mV/Div
L = 1.2 mH,
COUT = 10 mF
500 mA/Div
VIN = 3.6 V, L = 1.2 mH,
VOUT = 1.8 V, COUT = 10 mF
Load = 2R2
Time Base - 100 ms/Div
Time Base - 100 ms/Div
Figure 19. Line Transient PFM Mode
Figure 20. Startup Into Load – VOUT 1.8V
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s) :TPS62065 TPS62067
11
TPS62065, TPS62067
SLVS833 – MARCH 2010
www.ti.com
EN
1 V/Div
VIN = 3.6 V,
VOUT = 1.8 V,
COUT = 10 mF,
No Load
2 V/Div
SW
2 V/Div
2 V/Div
VOUT
1 V/Div
1 A/Div
VIN = 4.2 V,
VOUT = 3.3 V,
Load = 2R2
PG Pullup resistor 10 kW
2 V/Div
Time Base - 2ms/Div
Time Base - 100 ms/Div
Figure 21. Startup TPS62067 into 2.2-Ω Load with Power Good
Figure 22. Output Discharge
VIN = 4.2 V,
VOUT = 3.3 V,
Load = no load
PG Pullup resistor 10 kW
2 V/Div
2 V/Div
5 V/Div
Time Base - 1 ms/Div
Figure 23. Shutdown TPS62067
12
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s) :TPS62065 TPS62067
TPS62065, TPS62067
www.ti.com
SLVS833 – MARCH 2010
DETAILED DESCRIPTION
OPERATION
The TPS6206x step down converter operates with typically 3MHz fixed frequency pulse width modulation (PWM)
at moderate to heavy load currents. At light load currents the converter can automatically enter Power Save
Mode and operates then in PFM (Pulse Frequency Mode) mode.
During PWM operation the converter use a unique fast response voltage mode controller scheme with input
voltage feed-forward to achieve good line and load regulation allowing the use of small ceramic input and output
capacitors. At the beginning of each clock cycle initiated by the clock signal, the High Side MOSFET switch is
turned on. The current flows now from the input capacitor via the High Side MOSFET switch through the inductor
to the output capacitor and load. During this phase, the current ramps up until the PWM comparator trips and the
control logic will turn off the switch. The current limit comparator will also turn off the switch in case the current
limit of the High Side MOSFET switch is exceeded. After a dead time preventing shoot through current, the Low
Side MOSFET rectifier is turned on and the inductor current ramps down. The current flows now from the
inductor to the output capacitor and to the load. It returns back to the inductor through the Low Side MOSFET
rectifier..
The next cycle will be initiated by the clock signal again turning off the Low Side MOSFET rectifier and turning on
the High Side MOSFET switch.
POWER SAVE MODE
At TPS62065 pulling the Mode pin low enables Power Save Mode. In TPS62067 Power Save Mode is enabled
per default. If the load current decreases, the converter enters Power Save Mode operation automatically. During
Power Save Mode the converter skips switching and operates with reduced frequency in PFM mode with a
minimum quiescent current to maintain high efficiency. The converter positions the output voltage typically +1%
above the nominal output voltage. This voltage positioning feature minimizes voltage drops caused by a sudden
load step.
The transition from PWM mode to PFM mode occurs once the inductor current in the Low Side MOSFET switch
becomes zero, which indicates discontinuous conduction mode.
During the Power Save Mode the output voltage is monitored with a PFM comparator. As the output voltage falls
below the PFM comparator threshold of VOUTnominal +1%, the device starts a PFM current pulse. For this the High
Side MOSFET switch will turn on and the inductor current ramps up. After the On-time expires the switch will be
turned off and the Low Side MOSFET switch will be turned on until the inductor current becomes zero.
The converter effectively delivers a current to the output capacitor and the load. If the load is below the delivered
current the output voltage will rise. If the output voltage is equal or higher than the PFM comparator threshold,
the device stops switching and enters a sleep mode with typ. 18µA current consumption.
In case the output voltage is still below the PFM comparator threshold, further PFM current pulses will be
generated until the PFM comparator threshold is reached. The converter starts switching again once the output
voltage drops below the PFM comparator threshold due to the load current.
The PFM mode is exited and PWM mode entered in case the output current can no longer be supported in PFM
mode.
Dynamic Voltage Positioning
This feature reduces the voltage under/overshoots at load steps from light to heavy load and vice versa. It is
active in Power Save Mode and regulates the output voltage 1% higher than the nominal value. This provides
more headroom for both the voltage drop at a load step, and the voltage increase at a load throw-off.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s) :TPS62065 TPS62067
13
TPS62065, TPS62067
SLVS833 – MARCH 2010
www.ti.com
Output voltage
Voltage Positioning
Vout +1%
PFM Comparator
threshold
Light load
PFM Mode
Vout (PWM)
moderate to heavy load
PWM Mode
Figure 24. Power Save Mode Operation with automatic Mode transition
100% Duty Cycle Low Dropout Operation
The device starts to enter 100% duty cycle mode as the input voltage comes close to the nominal output voltage.
In order to maintain the output voltage, the High-Side MOSFET switch is turned on 100% for one or more cycles.
With further decreasing VIN the High-Side MOSFET switch is turned on completely. In this case the converter
offers a low input-to-output voltage difference. This is particularly useful in battery-powered applications to
achieve longest operation time by taking full advantage of the whole battery voltage range.
The minimum input voltage to maintain regulation depends on the load current and output voltage, and can be
calculated as:
VINmin = VOmax + IOmax × (RDS(on)max + RL)
With:
IOmax = maximum output current
RDS(on)max = maximum P-channel switch RDS(on).
RL = DC resistance of the inductor
VOmax = nominal output voltage plus maximum output voltage tolerance
Undervoltage Lockout
The under voltage lockout circuit prevents the device from malfunctioning at low input voltages and from
excessive discharge of the battery. It disables the output stage of the converter once the falling VIN trips the
under-voltage lockout threshold VUVLO. The under-voltage lockout threshold VUVLO for falling VIN is typically
1.78V. The device starts operation once the rising VIN trips under-voltage lockout threshold VUVLO again at
typically 1.95V.
Output Capacitor Discharge
With EN = GND, the device enters shutdown mode and all internal circuits are disabled. The SW pin is
connected to PGND via an internal resistor to discharge the output capacitor. This feature ensures a startup in a
discharged output capacitor once the converter is enabled again and prevents "floating" charge on the output
capacitor. The output voltage ramps up monotonic starting from 0V.
MODE SELECTION (TPS62065)
The MODE pin allows mode selection between forced PWM mode and Power Save Mode.
14
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s) :TPS62065 TPS62067
TPS62065, TPS62067
www.ti.com
SLVS833 – MARCH 2010
Connecting this pin to GND enables the Power Save Mode with automatic transition between PWM and PFM
mode. Pulling the MODE pin high forces the converter to operate in fixed frequency PWM mode even at light
load currents. This allows simple filtering of the switching frequency for noise sensitive applications. In this mode,
the efficiency is lower compared to the power save mode during light loads.
The condition of the MODE pin can be changed during operation and allows efficient power management by
adjusting the operation mode of the converter to the specific system requirements.
In device options where the MODE Pin is replaced with Power Good output, the Power Save Mode is enabled
per default.
POWER GOOD OUTPUT (TPS62067)
This function is available in the TPS62067. The Power Good Output is an open-drain output and requires an
external pull-up resistor. The circuit is active once the device is enabled and AVIN is above the undervoltage
lockout threshold VUVLO. It is driven by an internal comparator connected to the FB voltage. The PG output
provides a high level once the feedback voltage exceeds typically 95% of its nominal value. The PG output is
driven to low level once the feedback voltage falls below typically 90% of its nominal value. The PG output is
activated with an internal delay of 5µs.
The PG open-drain output transistor is turned on immediately with EN = low level and pulls the output low. The
external pull up resistor can be connected to any voltage rail lower or equal the voltage applied to AVIN of the
device. The value of the pull-up resistor need carefully selected in order to limit the current into the PG pin to
maximum 1.0mA. The external pull up resistor can be connected to VOUT or another voltage rail which does not
exceed the VIN level. The current flowing through the pull up resistor impacts the current consumption of the
application circuit in shutdown mode.
The shut down current of the device does not include the current through the external pull-up and internal
open-drain stage. The PG signal can be used for sequencing various converters or to reset a microcontroller.
EN
VOUT
Startup
95%
90%
Overload
Output
discharge
tRamp
tStart
PG
WithEN = low
PG --> low
Figure 25. Power Good Output PG
ENABLE
The device is enabled by setting EN pin to high. At first, the internal reference is activated and the internal
analog circuits are settled. Afterwards, the soft start is activated and the output voltage is ramped up. The output
voltages reaches 95% of its nominal value within tSTARTof typically 500 µs after the device has been enabled. The
EN input can be used to control power sequencing in a system with various DC/DC converters. The EN pin can
be connected to the output of another converter, to drive the EN pin high and getting a sequencing of supply
rails. With EN = GND, the device enters shutdown mode. In this mode, all circuits are disabled and the SW pin is
connected to PGND via an internal resistor to discharge the output.
SOFT START
The TPS6206x has an internal soft start circuit that controls the ramp up of the output voltage. Once the
converter is enabled and the input voltage is above the undervoltage lockout threshold VUVLOthe output voltage
ramps up from 5% to 95% of its nominal value within tRamp of typ. 250µs.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s) :TPS62065 TPS62067
15
TPS62065, TPS62067
SLVS833 – MARCH 2010
www.ti.com
This limits the inrush current in the converter during start up and prevents possible input voltage drops when a
battery or high impedance power source is used.
During soft start, the switch current limit is reduced to 1/3 of its nominal value ILIMF until the output voltage
reaches 1/3 of its nominal value. Once the output voltage trips this threshold, the device operates with its
nominal current limit ILIMF.
INTERNAL CURRENT LIMIT / FOLD-BACK CURRENT LIMIT FOR SHORT-CIRCUIT PROTECTION
During normal operation the High-Side and Low-Side MOSFET switches are protected by its current limits ILIMF.
Once the High-Side MOSFET switch reaches its current limit, it is turned off and the Low-Side MOSFET switch is
turned on. The High-Side MOSFET switch can only turn on again, once the current in the Low -Side MOSFET
switch decreases below its current limit ILIMF. The device is capable to provide peak inductor currents up to its
internal current limit ILIMF..
As soon as the switch current limits are hit and the output voltage falls below 1/3 of the nominal output voltage
due to overload or short circuit condition, the foldback current limit is enabled. In this case the switch current limit
is reduced to 1/3 of the nominal value ILIMF.
Due to the short-circuit protection is enabled during start-up, the device does not deliver more than 1/3 of its
nominal current limit ILIMF until the output voltage exceeds 1/3 of the nominal output voltage. This needs to be
considered when a load is connected to the output of the converter, which acts as a current sink.
CLOCK DITHERING
In order to reduce the noise level of switch frequency harmonics in the higher RF bands, the TPS6206x family
has a built-in clock-dithering circuit. The oscillator frequency is slightly modulated with a sub clock causing a
clock dither of typ. 6ns.
THERMAL SHUTDOWN
As soon as the junction temperature, TJ, exceeds 150°C (typical) the device goes into thermal shutdown. In this
mode, the High-Side and Low-Side MOSFETs are turned off. The device continues its operation with a softstart
once the junction temperature falls below the thermal shutdown hysteresis.
16
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s) :TPS62065 TPS62067
TPS62065, TPS62067
www.ti.com
SLVS833 – MARCH 2010
APPLICATION INFORMATION
L
1.0 mH
TPS62065
VIN = 3 V to 6 V
PVIN
SW
R1
360 kΩ
AVIN
EN
MODE
AGND
PGND
CIN
10 µF
VOUT = 1.8 V
up to 2 A
COUT
Cff
22 pF
10 µF
FB
R2
180 kΩ
Figure 26. TPS62065 1.8V Adjustable Output Voltage Configuration
L
1.0 mH
TPS62067
VIN = 3 V to 6 V
PVIN
SW
R1
360 kW
AVIN
EN
FB
CIN
10 mF
AGND
PGND
VOUT 1.8 V
2A
PG
Cff
COUT
22 pF 10 mF
RPG
100 kW
R2
180 kW
Figure 27. TPS62267 Adjustable 1.8-V Output
OUTPUT VOLTAGE SETTING
The output voltage can be calculated to:
R
V OUT + VREF
1) 1
R2
ǒ
Ǔ
with an internal reference voltage VREF typically 0.6V.
To minimize the current through the feedback divider network, R2 should be within the range of 120 kΩ to 360
kΩ. The sum of R1 and R2 should not exceed ~1MΩ, to keep the network robust against noise. An external
feed-forward capacitor Cff is required for optimum regulation performance. Lower resistor values can be used but
in this case the Cff needs to be adjusted according to the following equations.
Corner frequency of the feed forward network:
fc
=
1
= 35kHz
2 ´ p ´ R2 ´ Cff
Therefore the feed forward capacitor can be calculated to:
Cff =
1
2 ´ p ´ R2 ´ 35kHz
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s) :TPS62065 TPS62067
17
TPS62065, TPS62067
SLVS833 – MARCH 2010
www.ti.com
OUTPUT FILTER DESIGN (INDUCTOR AND OUTPUT CAPACITOR)
The internal compensation network of TPS6206x is optimized for a LC output filter with a corner frequency of:
fc =
1
= 50kHz
2 ´ p ´ (1μH ´ 10μF)
The part operates with nominal inductors of 1.0µH to 1.2 µH and with 10µF to 22µF small X5R and X7R ceramic
capacitors. Please refer to the lists of inductors and capacitors. The part is optimized for a 1.0µH inductor and
10µF output capacitor.
Inductor Selection
The inductor value has a direct effect on the ripple current. The selected inductor has to be rated for its dc
resistance and saturation current. The inductor ripple current (ΔIL) decreases with higher inductance and
increases with higher VI or VO.
Equation 1 calculates the maximum inductor current in PWM mode under static load conditions. The saturation
current of the inductor should be rated higher than the maximum inductor current as calculated with Equation 2.
This is recommended because during heavy load transient the inductor current rises above the calculated value.
DI L + Vout
1 * Vout
Vin
L
I Lmax + I outmax )
ƒ
(1)
DI L
2
(2)
With:
f = Switching Frequency (3MHz typical)
L = Inductor Value
ΔIL = Peak-to-Peak inductor ripple current
ILmax = Maximum Inductor current
A more conservative approach is to select the inductor current rating just for the switch current limit ILIMFof the
converter.
The total losses of the coil have a strong impact on the efficiency of the DC/DC conversion and consist of both
the losses in the dc resistance R(DC) and the following frequency-dependent components:
• The losses in the core material (magnetic hysteresis loss, especially at high switching frequencies)
• Additional losses in the conductor from the skin effect (current displacement at high frequencies)
• Magnetic field losses of the neighboring windings (proximity effect)
• Radiation losses
Table 2. List of Inductors
3
DIMENSIONS [mm ]
INDUCTANCE mH
INDUCTOR TYPE
SUPPLIER
3.2 x 2.5 x 1.0 max
1.0
LQM32PN (MLCC)
Murata
3.7 x 4 x 1.8 max
1.0
LQH44 (wire wound)
Murata
4.0 x 4.0 x 2.6 max
1.2
NRG4026T (wire wound)
Taiyo Yuden
3.5 x 3.7 x 1.8 max
1.2
DE3518 (wire wound)
TOKO
Output Capacitor Selection
The advanced fast-response voltage mode control scheme of the TPS6206x allows the use of tiny ceramic
capacitors. Ceramic capacitors with low ESR values have the lowest output voltage ripple and are
recommended. The output capacitor requires either an X7R or X5R dielectric. Y5V and Z5U dielectric capacitors,
aside from their wide variation in capacitance over temperature, become resistive at high frequencies and may
not be used. For most applications a nominal 10µF or 22µF capacitor is suitable. At small ceramic capacitors, the
DC-bias effect decreases the effective capacitance. Therefore a 22µF capacitor can be used for output voltages
higher than 2V, see list of capacitors.
18
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s) :TPS62065 TPS62067
TPS62065, TPS62067
www.ti.com
SLVS833 – MARCH 2010
In case additional ceramic capacitors in the supplied system are connected to the output of the DC/DC converter,
the output capacitor COUT need to be decreased in order not to exceed the recommended effective capacitance
range. In this case a loop stability analysis must be performed as described later.
At nominal load current, the device operates in PWM mode and the RMS ripple current is calculated as:
I RMSCout + Vout
1 * Vout
1
Vin
L
ƒ
2
Ǹ3
(3)
Input Capacitor Selection
Because of the nature of the buck converter having a pulsating input current, a low ESR input capacitor is
required for best input voltage filtering and minimizing the interference with other circuits caused by high input
voltage spikes. For most applications a 10µF ceramic capacitor is recommended. The input capacitor can be
increased without any limit for better input voltage filtering.
Take care when using only small ceramic input capacitors. When a ceramic capacitor is used at the input and the
power is being supplied through long wires, such as from a wall adapter, a load step at the output or VIN step on
the input can induce ringing at the VIN pin. This ringing can couple to the output and be mistaken as loop
instability or could even damage the part by exceeding the maximum ratings.
Table 3. List of Capacitors
CAPACITANCE
TYPE
SIZE [ mm3]
SUPPLIER
10mF
GRM188R60J106M
0603: 1.6 x 0.8 x 0.8
Murata
22mF
GRM188R60G226M
0603: 1.6 x 0.8 x 0.8
Murata
22µF
CL10A226MQ8NRNC
0603: 1.6 x 0.8 x 0.8
Samsung
10µF
CL10A106MQ8NRNC
0603: 1.6 x 0.8 x 0.8
Samsung
CHECKING LOOP STABILITY
The first step of circuit and stability evaluation is to look from a steady-state perspective at the following signal
• Switching node, SW
• Inductor current, IL
• Output ripple voltage, VOUT(AC)
These are the basic signals that need to be measured when evaluating a switching converter. When the
switching waveform shows large duty cycle jitter or the output voltage or inductor current shows oscillations, the
regulation loop may be unstable. This is often a result of board layout and/or wrong L-C output filter
combinations. As a next step in the evaluation of the regulation loop, the load transient response is tested. The
time between the application of the load transient and the turn on of the P-channel MOSFET, the output
capacitor must supply all of the current required by the load. VOUT immediately shifts by an amount equal to
ΔI(LOAD) x ESR, where ESR is the effective series resistance of COUT. ΔI(LOAD) begins to charge or discharge CO
generating a feedback error signal used by the regulator to return VOUT to its steady-state value. The results are
most easily interpreted when the device operates in PWM mode at medium to high load currents.
During this recovery time, VOUT can be monitored for settling time, overshoot, or ringing; that helps evaluate
stability of the converter. Without any ringing, the loop has usually more than 45° of phase margin.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s) :TPS62065 TPS62067
19
TPS62065, TPS62067
SLVS833 – MARCH 2010
www.ti.com
Mode/PG
Enable
LAYOUT CONSIDERATIONS
VIN
GND
CIN
COUT
R2
R1
CFF
GND
L
VOUT
Figure 28. PCB Layout
As for all switching power supplies, the layout is an important step in the design. Proper function of the device
demands careful attention to PCB layout. Care must be taken in board layout to get the specified performance. If
the layout is not carefully done, the regulator could show poor line and/or load regulation, stability issues as well
as EMI and thermal problems. It is critical to provide a low inductance, impedance ground path. Therefore, use
wide and short traces for the main current paths. The input capacitor should be placed as close as possible to
the IC pins as well as the inductor and output capacitor.
Connect the AGND and PGND Pins of the device to the PowerPAD™ land of the PCB and use this pad as a star
point. Use a common Power PGND node and a different node for the Signal AGND to minimize the effects of
ground noise. The FB divider network should be connected right to the output capacitor and the FB line must be
routed away from noisy components and traces (e.g., SW line).
Due to the small package of this converter and the overall small solution size the thermal performance of the
PCB layout is important. To get a good thermal performance a four or more Layer PCB design is recommended.
The PowerPAD of the IC must be soldered on the power pad area on the PCB to get a proper thermal
connection. For good thermal performance the PowerPAD on the PCB needs to be connected to an inner GND
plane with sufficient via connections. Please refer to the documentation of the evaluation kit.
20
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s) :TPS62065 TPS62067
PACKAGE OPTION ADDENDUM
www.ti.com
22-Mar-2010
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TPS62065DSGR
ACTIVE
WSON
DSG
8
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS62065DSGT
ACTIVE
WSON
DSG
8
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS62067DSGR
ACTIVE
WSON
DSG
8
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS62067DSGT
ACTIVE
WSON
DSG
8
250
CU NIPDAU
Level-2-260C-1 YEAR
Green (RoHS &
no Sb/Br)
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DLP® Products
www.dlp.com
Communications and
Telecom
www.ti.com/communications
DSP
dsp.ti.com
Computers and
Peripherals
www.ti.com/computers
Clocks and Timers
www.ti.com/clocks
Consumer Electronics
www.ti.com/consumer-apps
Interface
interface.ti.com
Energy
www.ti.com/energy
Logic
logic.ti.com
Industrial
www.ti.com/industrial
Power Mgmt
power.ti.com
Medical
www.ti.com/medical
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
RFID
www.ti-rfid.com
Space, Avionics &
Defense
www.ti.com/space-avionics-defense
RF/IF and ZigBee® Solutions www.ti.com/lprf
Video and Imaging
www.ti.com/video
Wireless
www.ti.com/wireless-apps
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2010, Texas Instruments Incorporated
Similar pages