CLV6450A-LF 9939 Via Pasar • San Diego, CA 92126 TEL (858) 621-2700 FAX (858) 621-2722 VOLTAGE CONTROLLED OSCILLATOR Rev A1 £(f) (dBc/Hz) PHASE NOISE (1 Hz BW, typical) FEATURES • Frequency Range: 6250 - 6650 MHz • Tuning Voltage: 0.5 - 8 Vdc • MINI-16 - Style Package APPLICATIONS • Basestations • Satellite Communications • OFFSET (Hz) VALUE UNITS 6250 - 6650 MHz -89 dBc/Hz Harmonic Suppression (2nd, typ.) Tuning Voltage Tuning Sensitivity (avg.) -20 0.5 - 8 74 dBc Vdc MHz/V Power Output 2.5±2.5 dBm PERFORMANCE SPECIFICATIONS Oscillation Frequency Range Phase Noise @ 10 kHz offset (1 Hz BW, typ.) Load Impedance 50 Input Capacitance (max.) 10 Pushing <3 MHz/V Pulling (14 dB Return Loss, Any Phase) pF <4 MHz Operating Temperature Range -40 to 85 °C Package Style MINI-16 POWER SUPPLY REQUIREMENTS Supply Voltage (Vcc, nom.) Supply Current (Icc, typ.) 8 Vdc 26 mA All specifications are typical unless otherwise noted and subject to change without notice. APPLICATION NOTES • AN-100/1 : Mounting and Grounding of VCOs • AN-102 : Proper Output Loading of VCOs • AN-107 : How to Solder Z-COMM VCOs NOTES: Phase Noise @ 1 kHz offset (1 Hz BW, max.): -82dBc/Hz © Z-Communications, Inc. Page 1 All rights reserved LOW COST - HIGH PERFORMANCE VOLTAGE CONTROLLED OSCILLATOR CLV6450A-LF PAGE 2 FREQUENCY (MHz) TUNING CURVE, typ. 6710 6680 6650 6620 6590 6560 6530 6500 6470 6440 6410 6380 6350 6320 6290 6260 6230 6200 -40 °c °c °c 25 °c 85 25 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 6.5 7 7.5 8 TUNING VOLTAGE (Vdc) POWER OUTPUT (dBm) POWER CURVE, typ. 8 7 6 5 4 3 2 1 0 6195 6277 6354 6446 6530 6596 6646 6677 6697 FREQUENCY (MHz) PHYSICAL DIMENSIONS TYPICAL OF ALL PADS MINI-16 415-0061 REV. D (DRAWING NOT TO SCALE) SEE NOTE 3 .070 .037 NOTES: 1. THE INSIDE RADIUS OF ALL 16 HALF HOLES AT THE PERIMETER OF THE BOARD ARE PLATED TO PROVIDE A SURFACE FOR THE ATTACHMENT OF THE VCO TO A PCB, IN 13 LOCATIONS, WITH 3 PADS BEING USED FOR ELECTROMECHANICAL INTERFACE. 16 SOLDER LOCATIONS REQUIRED. 2. THE SURFACE OF THE SHIELD IS TIN PLATED AND MAY BE SOLDERED TO. THE SHIELD'S BASE METAL IS COLD ROLLED STEEL. 3. THE GROUND PLANE IS GROUND AND ATTACHES TO A GROUND TRACK ON THE UPPER SIDE OF THE BOARD AS WELL AS THE SHIELD BY PTH. 4. UNLESS OTHERWISE NOTED ALL DIMENSIONS ARE IN INCHES. 5. UNLESS OTHERWISE NOTED ALL TOLERANCES ARE AS FOLLOWS: TOLERANCES .XXX= ± .010 .031 .052 .114 0.500 0.500 0.475 DETAIL A P2 0.415 0.405 0.305 0.315 P3 0.205 -.005 P1=VT P2=RF OUT P3=Vcc TABS RANGE: SEE NOTE 5. (4 PLACES) 0.215 .465 0.475 0.420 0.320 0.000 0.115 0.220 .026 BOTTOM VIEW 0.105 0.115 SEE DETAIL 'A' P1 .220 .070 TYP .150 0.500 0.385 .034 0.000 0.285 0.185 0.085 0.025 0.025 0.000 TYP GROUND PLANE SOLDER PLATED © Z-Communications, Inc. Page 2 Printed in the U.S.A.