CUI CPE-960 Piezo audio indicator Datasheet

page
1 of 5
date
11/12/2007
DESCRIPTION: piezo audio indicators
PART NUMBER: CPE-960
SPECIFICATONS
operating frequency
operating voltage range
current consumption
sound pressure level
rated voltage
tone
operating tempurature
storage tempurature
dimensions
weight
material
terminal
RoHS
2.5 ± 0.5 KHz
3 ~ 16 V DC
58 mA max.
at 12 V DC
100 db min.
at 30 cm/12 V DC
12 V DC
continuous
-30 ~ +80° C
-40 ~ +80° C
Ø50.0 x H37.5 mm
35.0 g max.
ABS UL-94 1/16” high heat (black)
wire type
yes
APPEARANCE DRAWING
tolerance: ±0.5
units: mm
3.5
(2 PLCS)
10.0
UL1007 LF 24AWG
5.0
70.0
2.0
black
red
150.0
50.0
60.0
5.0
37.5
20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2383
5.0
(2 PLCS)
PART NUMBER: CPE-960
page
2 of 5
date
11/12/2007
DESCRIPTION: piezo audio indicators
MEASUREMENT METHOD
S.P.L. Measuring Circuit
Mic: RION S.P.L. meter UC30 or equivalent
S.G.: Hewlett Packard 33120A function gernerator or equivalent
CURRENT CONSUMPTION/SOUND PRESSURE LEVEL
20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2383
page
3 of 5
date
11/12/2007
DESCRIPTION: piezo audio indicators
PART NUMBER: CPE-960
MECHANICAL CHARACTERISTICS
item
solderability
lead wire pull strength
vibration
drop test
test condition
Stripped wires are immersed in rosin for
5 seconds and then immersed in solder bath
of 270 ±5°C for 3 ±1 seconds.
The pull force shall be applied to lead wire:
Horizontal
3.0N for 30 seconds
Vertical
2.0N for 30 seconds
The buzzer shall be measured after applying
a vibration amplitude of 1.5 mm with 10 to
55 Hz band of vibration frequency to each of
the 3 perpendicular directions for 2 hours.
The part will be dropped from a height of
75 cm onto a 40 mm thick wooden board 3
times in 3 axes (X, Y, Z) for a total of 9 drops.
evaluation standard
90% min. of the lead terminals
will be wet with solder
(except the edge of the terminal).
test condition
After being placed in a chamber at +80°C for
240 hours.
After being placed in a chamber at -40°C for
240 hours.
After being placed in a chamber at +40°C and
90±5% relative humidity for 240 hours.
The part shall be subjected to 5 cycles. One
cycle will consist of:
evaluation standard
No damage or cutting off.
The value of oscillation
frequency/current consumption
should be ±10% of the initial
measurements. The SPL should
be within ±10dB compared with
the initial measurement.
ENVIRONMENT TEST
item
high temp. test
low temp. test
humidity test
temp. cycle test
+80
+25
+25
-40
0.5hr 0.5hr 0.25 0.5hr
0.5hr
The buzzer will be measured after
being placed at +25°C for 4
hours. The value of the
oscillation frequency/current
consumption should be ±10%
compared to the initial
measurements. The SPL should
be within ±10dB compared to the
initial measurements.
0.5hr 0.25
3hours
20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2383
page
4 of 5
date
11/12/2007
DESCRIPTION: piezo audio indicators
PART NUMBER: CPE-960
RELIABILITY TEST
item
operating (life test)
test condition
1. Continuous life test:
The part will be subjected to 48 hours of
continuous operation at +65°C with rated
voltage applied.
2. Intermittent life test:
A duty cycle of 1 minute on, 1 minutes off, a
minimum of 5,000 times at room temp
(+25 ±2°C) with rated voltage applied.
evaluation standard
The buzzer will be measured after
being placed at +25°C for 4
hours. The value of the
oscillation frequency/current
consumption should be ±10%
compared to the initial
measurements. The SPL should
be within ±10dB compared to
the initial measurements.
TEST CONDITIONS
standard test condition
judgement test condition
a) tempurature: +5 ~ +35°C
a) tempurature: +25 ±2°C
b) humidity: 45 - 85%
b) humidity: 60 - 70%
c) pressure: 860-1060 mbar
c) pressure: 860-1060 mbar
20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2383
PART NUMBER: CPE-960
page
5 of 5
date
11/12/2007
DESCRIPTION: piezo audio indicators
PACKAGING
20050 SW 112th Ave. Tualatin, Oregon 97062 phone 503.612.2300 fax 503.612.2383
Similar pages