Cirrus CS4202 Audio codec 97 with headphone amplifier Datasheet

CS4202
Audio Codec ’97 with Headphone Amplifier
Features
AC ’97 2.2 Compliant
Exceeds the Microsoft PC 2001 Audio
Performance Requirements
Integrated High-Performance Headphone
Amplifier
On-chip PLL for use with External Clock
Sources
Integrated High-Performance Microphone
Pre-Amplifier
Automatic Jack Sense through GPIO
BIOS-Driver Interface for Audio Feature
Configuration through Software
S/PDIF Digital Audio Output
I2S Serial Digital Outputs Enable Cost
Effective Six Channel Applications
Independent Simultaneous S/PDIF and Six
Channel Audio Playback
20-bit Stereo Digital-to-Analog Converters
18-bit Stereo Analog-to-Digital Converters
Sample Rate Converters
Three Analog Line-level Stereo Inputs
High Quality Pseudo-Differential CD Input
Two Analog Line-level Mono Inputs
Dual Microphone Inputs
Stereo and Mono Line-level Outputs
Extensive Power Management Support
Description
The CS4202 is an AC ’97 2.2 compliant stereo audio codec designed for PC multimedia systems. It uses
industry leading delta-sigma and mixed signal technology. This advanced technology and these features are
designed to help enable the design of PC 99 and
PC 2001 compliant high-quality audio systems for desktop, portable, and entertainment PCs.
Coupling the CS4202 with a PCI audio accelerator or
core logic supporting the AC ’97 interface implements a
cost effective, superior quality audio solution. The
CS4202 surpasses PC 99, PC 2001, and AC ’97 2.2 audio quality standards.
ORDERING INFO
CS4202-JQ 48-pin TQFP
AC-LINK AND AC '97
REGISTERS
ANALOG INPUT MUX
AND OUTPUT MIXER
PWR
MGT
TEST
LINE
SRC
SYNC
PCM_DATA
18 bit
ADC
INPUT
MUX
CD
AUX
VIDEO
BIT_CLK
SDATA_OUT
SDATA_IN
ACLINK
INPUT
MIXER
RESET#
GAIN / MUTE CONTROLS
MIXER / MUX SELECTS
ID0#
ID1#
Σ
AC '97
REGISTERS
OUTPUT
MIXER
EAPD
SPDIF_OUT
GPIO[4:0]
9x9x1.4 mm
GPIO, S/PDIF
SERIAL DATA PORT
SRC
PCM_DATA
20 bit
DAC
Σ
MIC1
MIC2
PHONE
PC_BEEP
LINE_OUT
HP_OUT
MONO_OUT
SDOUT,LRCLK,SCLK
Preliminary Product Information
P.O. Box 17847, Austin, Texas 78760
(512) 445 7222 FAX: (512) 445 7581
http://www.cirrus.com
This document contains information for a new product.
Cirrus Logic reserves the right to modify this product without notice.
Copyright  Cirrus Logic, Inc. 2002
(All Rights Reserved)
MAY ’02
DS549PP1
1
CS4202
TABLE OF CONTENTS
1. CHARACTERISTICS AND SPECIFICATIONS ........................................................................ 6
ANALOG CHARACTERISTICS ................................................................................................ 6
ABSOLUTE MAXIMUM RATINGS ........................................................................................... 7
RECOMMENDED OPERATING CONDITIONS ....................................................................... 7
AC ’97 SERIAL PORT TIMING................................................................................................. 9
2. GENERAL DESCRIPTION ..................................................................................................... 12
2.1 AC-Link ............................................................................................................................ 12
2.2 Control Registers ............................................................................................................. 13
2.3 Sample Rate Converters .................................................................................................. 13
2.4 Mixers .............................................................................................................................. 13
2.5 Input Mux ......................................................................................................................... 13
2.6 Volume Control ................................................................................................................ 13
3. AC-LINK FRAME DEFINITION .............................................................................................. 15
3.1 AC-Link Serial Data Output Frame .................................................................................. 16
3.1.1 Serial Data Output Slot Tags (Slot 0)............................................................................. 16
3.1.2 Command Address Port (Slot 1) .................................................................................... 16
3.1.3 Command Data Port (Slot 2).......................................................................................... 17
3.1.4 PCM Playback Data (Slots 3-4,6-11) ............................................................................. 17
3.1.5 GPIO Pin Control (Slot12).............................................................................................. 17
3.2 AC-Link Serial Data Input Frame ..................................................................................... 18
3.2.1 Serial Data Input Slot Tag Bits (Slot 0) ........................................................................ 18
3.2.2 Status Address Port (Slot 1) .......................................................................................... 18
3.2.3 Status Data Port (Slot 2) ................................................................................................ 19
3.2.4 PCM Capture Data (Slot 3-4,6-8,11).............................................................................. 19
3.2.5 GPIO Pin Status (Slot 12) ............................................................................................. 19
3.3 AC-Link Protocol Violation - Loss of SYNC ..................................................................... 20
4. REGISTER INTERFACE ..................................................................................................... 21
4.1 Reset Register (Index 00h) .............................................................................................. 22
4.2 Analog Mixer Output Volume Registers (Index 02h - 04h) .............................................. 22
4.3 Mono Volume Register (Index 06h) .................................................................................. 23
4.4 PC_BEEP Volume Register (Index 0Ah) .......................................................................... 23
Contacting Cirrus Logic Support
For a complete listing of Direct Sales, Distributor, and Sales Representative contacts, visit the Cirrus Logic web site at:
http://www.cirrus.com/corporate/contacts/sales.cfm
IMPORTANT NOTICE
"Preliminary" product information describes products that are in production, but for which full characterization data is not yet available. "Advance" product information describes products that are in development and subject to development changes. Cirrus Logic, Inc. and its subsidiaries ("Cirrus") believe that the information contained in this document is accurate and reliable. However, the information is subject to change without notice and is provided "AS IS" without warranty
of any kind (express or implied). Customers are advised to obtain the latest version of relevant information to verify, before placing orders, that information being
relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those
pertaining to warranty, patent infringement, and limitation of liability. No responsibility is assumed by Cirrus for the use of this information, including use of this
information as the basis for manufacture or sale of any items, or for infringement of patents or other rights of third parties. This document is the property of Cirrus
and by furnishing this information, Cirrus grants no license, express or implied under any patents, mask work rights, copyrights, trademarks, trade secrets or
other intellectual property rights. Cirrus owns the copyrights of the information contained herein and gives consent for copies to be made of the information only
for use within your organization with respect to Cirrus integrated circuits or other parts of Cirrus. This consent does not extend to other copying such as copying
for general distribution, advertising or promotional purposes, or for creating any work for resale.
An export permit needs to be obtained from the competent authorities of the Japanese Government if any of the products or technologies described in this material and controlled under the "Foreign Exchange and Foreign Trade Law" is to be exported or taken out of Japan. An export license and/or quota needs to be
obtained from the competent authorities of the Chinese Government if any of the products or technologies described in this material is subject to the PRC Foreign
Trade Law and is to be exported or taken out of the PRC.
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE
PROPERTY OR ENVIRONMENTAL DAMAGE ("CRITICAL APPLICATIONS"). CIRRUS PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF CIRRUS PRODUCTS
IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER'S RISK.
Cirrus Logic, Cirrus, and the Cirrus Logic logo designs are trademarks of Cirrus Logic, Inc. All other brand and product names in this document may be trademarks or service marks of their respective owners.
2
DS549PP1
CS4202
4.5 Phone Volume Register (Index 0Ch) ................................................................................ 23
4.6 Microphone Volume Register (Index 0Eh)........................................................................ 24
4.7 Analog Mixer Input Gain Registers (Index 10h - 18h) ...................................................... 25
4.8 Input Mux Select Register (Index 1Ah) ............................................................................. 26
4.9 Record Gain Register (Index 1Ch) ................................................................................... 27
4.10 General Purpose Register (Index 20h) ......................................................................... 28
4.11 Powerdown Control/Status Register (Index 26h) ........................................................... 29
4.12 Extended Audio ID Register (Index 28h) ........................................................................ 30
4.13 Extended Audio Status/Control Register (Index 2Ah) .................................................... 31
4.14 Audio Sample Rate Control Registers (Index 2Ch - 32h) ............................................... 32
4.15 S/PDIF Control Register (Index 3Ah) ............................................................................. 33
4.16 Extended Modem ID Register (Index 3Ch) .................................................................... 34
4.17 Extended Modem Status/Control Register (Index 3Eh) ................................................. 34
4.18 GPIO Pin Configuration Register (Index 4Ch) ................................................................ 34
4.19 GPIO Pin Polarity/Type Configuration Register (Index 4Eh) .......................................... 35
4.20 GPIO Pin Sticky Register (Index 50h) ............................................................................ 35
4.21 GPIO Pin Wakeup Mask Register (Index 52h) ............................................................... 36
4.22 GPIO Pin Status Register (Index 54h)............................................................................ 36
4.23 AC Mode Control Register (Index 5Eh) .......................................................................... 36
4.24 Misc. Crystal Control Register (Index 60h) ..................................................................... 38
4.25 Serial Port Control Register (Index 6Ah) ........................................................................ 39
4.26 BIOS-Driver Interface Control Registers (Index 70h - 72h) ............................................ 40
4.27 BIOS-Driver Interface Status Register (Index 7Ah) ........................................................ 40
4.28 Vendor ID1 Register (Index 7Ch) ................................................................................... 41
4.29 Vendor ID2 Register (Index 7Eh) ................................................................................... 41
5. SERIAL DATA PORTS ........................................................................................................... 42
5.1 Overview .......................................................................................................................... 42
5.2 Multi-Channel Expansion ................................................................................................. 42
5.3 Serial Data Formats ......................................................................................................... 43
6. SONY/PHILIPS DIGITAL INTERFACE (S/PDIF) ................................................................... 44
7. EXCLUSIVE FUNCTIONS ...................................................................................................... 44
8. POWER MANAGEMENT ....................................................................................................... 45
8.1 AC ’97 Reset Modes ........................................................................................................ 45
8.1.1 Cold Reset .......................................................................................................... 45
8.1.2 Warm Reset ........................................................................................................ 45
8.1.3 New Warm Reset ................................................................................................ 45
8.1.4 Register Reset .................................................................................................... 45
8.2 Powerdown Controls ....................................................................................................... 46
9. CLOCKING ............................................................................................................................. 48
9.1 PLL Operation (External Clock) ....................................................................................... 48
9.2 24.576 MHz Crystal Operation ........................................................................................ 48
9.3 Secondary Codec Operation ........................................................................................... 48
10. ANALOG HARDWARE DESCRIPTION ............................................................................... 50
10.1 Analog Inputs ................................................................................................................. 50
10.1.1 Line Inputs ........................................................................................................ 50
10.1.2 CD Input ............................................................................................................ 50
10.1.3 Microphone Inputs ............................................................................................ 50
10.1.4 PC Beep Input ................................................................................................... 51
10.1.5 Phone Input ....................................................................................................... 51
10.2 Analog Outputs .............................................................................................................. 51
10.2.1 Stereo Outputs .................................................................................................. 51
10.2.2 Mono Output ..................................................................................................... 52
10.3 Miscellaneous Analog Signals ....................................................................................... 52
10.4 Power Supplies .............................................................................................................. 52
DS549PP1
3
CS4202
10.5 Reference Design .......................................................................................................... 53
11. GROUNDING AND LAYOUT .............................................................................................. 54
12. PIN DESCRIPTIONS
........................................................................................................ 56
13. PARAMETER AND TERM DEFINITIONS ............................................................................ 62
14. REFERENCE DESIGN
................................................................................................... 64
15. REFERENCES ...................................................................................................................... 65
16. PACKAGE DIMENSIONS ..................................................................................................... 66
LIST OF FIGURES
Figure 1. Power Up Timing............................................................................................................ 10
Figure 2. Codec Ready from Start-up or Fault Condition .............................................................. 10
Figure 3. Clocks ............................................................................................................................ 10
Figure 4. Data Setup and Hold ...................................................................................................... 11
Figure 5. PR4 Powerdown and Warm Reset ................................................................................ 11
Figure 6. Test Mode ...................................................................................................................... 11
Figure 7. AC-link Connections....................................................................................................... 12
Figure 8. CS4202 Mixer Diagram.................................................................................................. 14
Figure 9. AC-link Input and Output Framing.................................................................................. 15
Figure 10. Serial Data Port: Six Channel Circuit ........................................................................... 42
Figure 11. Serial Data Format 0 (I2S) ........................................................................................... 43
Figure 12. Serial Data Format 1 (Left Justified) ............................................................................ 43
Figure 13. Serial Data Format 2 (Right Justified, 20-bit data) ....................................................... 43
Figure 14. Serial Data Format 3 (Right Justified, 16-bit data) ....................................................... 43
Figure 15. S/PDIF Output.............................................................................................................. 44
Figure 16. PLL External Loop Filter............................................................................................... 48
Figure 17. External Crystal............................................................................................................ 49
Figure 18. Line Input (Replicate for Video and AUX) .................................................................... 50
Figure 19. Differential 1 VRMS CD Input ...................................................................................... 50
Figure 20. Microphone Input ......................................................................................................... 51
Figure 21. PC_BEEP Input............................................................................................................ 51
Figure 22. Modem Connection ...................................................................................................... 51
Figure 23. Line Out and Headphone Out Setup ............................................................................ 52
Figure 24. Line Out/Headphone Out Setup ................................................................................... 52
Figure 25. +5V Analog Voltage Regulator..................................................................................... 53
Figure 26. Conceptual Layout for the CS4202 when in XTAL or OSC Clocking Modes ............... 55
Figure 27. Pin Locations for the CS4202 ...................................................................................... 56
Figure 28. CS4202 Reference Design .......................................................................................... 64
4
DS549PP1
CS4202
LIST OF TABLES
Table 1. Register Overview for the CS4202 ..................................................................... 21
Table 2. Analog Mixer Output Attenuation........................................................................ 22
Table 3. Microphone Input Gain Values ........................................................................... 24
Table 4. Analog Mixer Input Gain Values ......................................................................... 25
Table 5. Analog Mixer Input Gain Register Index ............................................................. 25
Table 6. Input Mux Selection ............................................................................................ 26
Table 7. Record Gain Values ........................................................................................... 27
Table 8. Slot Mapping for the CS4202 ............................................................................. 30
Table 9. Slot Assignment Defaults ................................................................................... 30
Table 10. Directly Supported SRC Sample Rates for the CS4202................................... 32
Table 11. GPIO Input/Output Configurations.................................................................... 35
Table 12. Serial Data Format Selection............................................................................ 39
Table 13. Device ID with Corresponding Part Number..................................................... 41
Table 14. Serial Data Formats and Compatible DACs for the CS4202 ............................ 43
Table 15. Powerdown PR Bit Functions ........................................................................... 46
Table 16. Powerdown PR Function Matrix for the CS4202 .............................................. 47
Table 17. Power Consumption by Powerdown Mode for the CS4202 ............................. 47
Table 18. Clocking Configurations for the CS4202 .......................................................... 49
DS549PP1
5
CS4202
1. CHARACTERISTICS AND SPECIFICATIONS
ANALOG CHARACTERISTICS (Standard test conditions unless otherwise noted: Tambient = 25° C,
AVdd = 5.0 V ±5%, DVdd = 3.3 V ±5%; 1 kHz Input Sine wave; Sample Frequency, Fs = 48 kHz; ZAL=100 kΩ/
1000 pF load for Mono and Line Outputs; CDL = 18 pF load (Note 1); Measurement bandwidth is 20 Hz - 20 kHz,
18-bit linear coding for ADC functions, 20-bit linear coding for DAC functions; Mixer registers set for unity gain.
Parameter
(Note 2)
Symbol
Full Scale Input Voltage
Line Inputs
Mic Inputs
(10dB = 0, 20dB = 0)
Mic Inputs
(10dB = 1, 20dB = 0)
Mic Inputs
(10dB = 0, 20dB = 1)
Mic Inputs
(10dB = 1, 20dB = 1)
Full Scale Output Voltage
Line and Mono Outputs
Headphone Output
Frequency Response
(Note 4)
FR
Analog
Ac = ± 0.25 dB
DAC
Ac = ± 0.25 dB
ADC
Ac = ± 0.25 dB
Dynamic Range
DR
Stereo Analog Inputs to LINE_OUT
Mono Analog Input to LINE_OUT
DAC Dynamic Range
ADC Dynamic Range
DAC SNR
SNR
(-20 dB FS input w/ CCIR-RMS filter on output)
THD+N
Total Harmonic Distortion + Noise
(-3 dB FS input signal):
Line Output
Headphone Output
DAC
ADC
(all inputs)
Power Supply Rejection Ratio
(1 kHz, 0.5 VRMS w/ 5 V DC offset)
(Note 4)
Interchannel Isolation
Spurious Tone
Input Impedance
(Note 4)
(Note 4)
CS4202-JQ
Path
(Note 3)
Min
Typ
Max
Unit
A-D
A-D
A-D
A-D
A-D
0.91
0.91
0.283
0.091
0.0283
1.00
1.00
0.315
0.10
0.0315
-
VRMS
VRMS
VRMS
VRMS
VRMS
D-A
D-A
0.91
-
1.0
1.4
1.13
-
VRMS
VRMS
A-A
D-A
A-D
20
20
20
-
20,000
20,000
20,000
Hz
Hz
Hz
A-A
A-A
D-A
A-D
90
85
85
85
95
90
90
90
-
dB FS
dB FS
dB FS
dB FS
D-A
-
70
-
dB
A-A
A-A
D-A
A-D
-
-90
-75
-87
-84
-80
-70
-80
-80
40
60
-
dB
70
10
87
-100
-
-
dB
dB FS
kΩ
dB
dB
dB
dB
A
A
A
A
FS
FS
FS
FS
Notes: 1. ZAL refers to the analog output pin loading and C DL refers to the digital output pin loading.
2. Parameter definitions are given in Section 13, Parameter and Term Definitions.
3. Path refers to the signal path used to generate this data. These paths are defined in Section 13,
Parameter and Term Definitions.
4. This specification is guaranteed by silicon characterization; it is not production tested.
6
DS549PP1
CS4202
ANALOG CHARACTERISTICS
(Continued)
Parameter
(Note 2)
Symbol
External Load Impedance
Line Output, Mono Output
Headphone Output
Output Impedance
Line Output, Mono Output
Headphone Output
Input Capacitance
Vrefout
Path
(Note 3)
(Note 4)
(Note 4)
CS4202-JQ
Unit
Min
Typ
Max
10
32
-
-
kΩ
Ω
2.3
730
0.8
5
2.4
2.5
Ω
Ω
pF
V
MIXER CHARACTERISTICS
Parameter
Mixer Gain Range Span
PC Beep
Line In, Aux, CD, Video, Mic1, Mic2, Phone
Mono Out, Line Out, Headphone Out
ADC Gain
Step Size
All volume controls except PC Beep
PC Beep
ABSOLUTE MAXIMUM RATINGS
Total Power Dissipation
Input Current per Pin
Output Current per Pin
Analog Input voltage
+3.3 V Digital
+5 V Digital
Analog
(Supplies, Inputs, Outputs)
(Except Supply Pins)
(Except Supply Pins)
Digital Input voltage
Ambient Temperature
Storage Temperature
Typ
Max
Unit
-
45.0
46.5
46.5
22.5
-
dB
dB
dB
dB
-
1.5
3.0
-
dB
dB
Max
5.5
5.5
5.5
1.25
10
15
AVdd+
0.3
DVdd +
0.3
70
150
Unit
V
V
V
W
mA
mA
V
(AVss1 = AVss2 = DVss1 = DVss2 = 0 V)
Parameter
Power Supplies
Min
(Power Applied)
Min
-0.3
-0.3
-0.3
-10
-15
-0.3
Typ
-
-0.3
-
0
-65
-
V
°C
°C
RECOMMENDED OPERATING CONDITIONS (AVss1 = AVss2 = DVss1 = DVss2 = 0 V)
Parameter
Power Supplies
Operating Ambient Temperature
DS549PP1
Symbol
+3.3 V Digital DVdd1, DVdd2
+5 V Digital DVdd1, DVdd2
Analog AVdd1, AVdd2
Min
3.135
4.75
4.75
0
Typ
3.3
5
5
-
Max
3.465
5.25
5.25
70
Unit
V
V
V
°C
7
CS4202
DIGITAL CHARACTERISTICS
(AVss1 = AVss2 = DVss1 = DVss2 = 0 V)
Parameter
DVdd = 3.3V
Low level input voltage
High level input voltage
High level output voltage
Low level output voltage
Input Leakage Current (AC-link inputs)
Output Leakage Current (Tri-stated AC-link outputs)
Output buffer drive current
BIT_CLK, SDATA_IN
SPDIF_OUT
EAPD/SCLK, GPIO0/LRCLK, GPIO1/SDOUT,
GPIO2, GPIO3, GPIO4/SDO2
(Note 4)
DVdd = 5.0 V
Low level input voltage
High level input voltage
High level output voltage
Low level output voltage
Input Leakage Current (AC-link inputs)
Output Leakage Current (Tri-stated AC-link outputs)
Output buffer drive current
BIT_CLK, SDATA_IN
SPDIF_OUT
EAPD/SCLK, GPIO0/LRCLK, GPIO1/SDOUT,
GPIO2, GPIO3, GPIO4/SDO2
(Note 4)
8
Symbol
Min
Typ
Max
Unit
Vil
Vih
Voh
Vol
2.15
3.00
-10
-10
3.25
0.03
-
0.80
0.35
10
10
V
V
V
V
µA
µA
-
72
24
-
mA
mA
-
4
-
mA
3.25
4.50
-10
-10
4.95
0.03
-
0.80
0.35
10
10
V
V
V
V
µA
µA
-
72
24
-
mA
mA
-
4
-
mA
Vil
Vih
Voh
Vol
DS549PP1
CS4202
AC ’97 SERIAL PORT TIMING Standard test conditions unless otherwise noted: Tambient = 25° C,
AVdd = 5.0 V, DVdd = 3.3 V; CL = 55 pF load.
Parameter
RESET Timing
RESET# active low pulse width
RESET# inactive to BIT_CLK start-up delay
(XTL mode)
(OSC mode)
(PLL mode)
1st SYNC active to CODEC READY ‘set’
Vdd stable to RESET# inactive
Clocks
BIT_CLK frequency
BIT_CLK period
BIT_CLK output jitter (depends on XTL_IN source)
BIT_CLK high pulse width
BIT_CLK low pulse width
SYNC frequency
SYNC period
SYNC high pulse width
SYNC low pulse width
Data Setup and Hold
Output propagation delay from rising edge of BIT_CLK
Input setup time from falling edge of BIT_CLK
Input hold time from falling edge of BIT_CLK
Input signal rise time
Input signal fall time
Output signal rise time
(Note 4)
Output signal fall time
(Note 4)
Misc. Timing Parameters
End of Slot 2 to BIT_CLK, SDATA_IN low (PR4)
SYNC pulse width (PR4) Warm Reset
SYNC inactive (PR4) to BIT_CLK start-up delay
Setup to trailing edge of RESET# (ATE test mode) (Note 4)
Rising edge of RESET# to Hi-Z delay
(Note 4)
DS549PP1
Symbol
Min
Typ
Max
Unit
Trst_low
Trst2clk
1.0
100
4.0
4.0
2.5
62.5
-
-
µs
µs
µs
ms
µs
µs
36
36
-
12.288
81.4
40.7
40.7
48
20.8
1.3
19.5
750
45
45
-
MHz
ns
ps
ns
ns
kHz
µs
µs
µs
Tisetup
Tihold
Tirise
Tifall
Torise
Tofall
8
10
0
2
2
2
2
10
4
4
12
6
6
6
6
ns
ns
ns
ns
ns
ns
ns
Ts2_pdown
Tsync_pr4
Tsync2clk
Tsetup2rst
Toff
1.0
162.8
15
-
0.285
285
-
1.0
25
µs
µs
ns
ns
ns
Tsync2crd
Tvdd2rst#
Fclk
Tclk_period
Tclk_high
Tclk_low
Fsync
Tsync_period
Tsync_high
Tsync_low
Tco
9
CS4202
BIT_CLK
Trst_low
Trst2clk
00000000000000000000000000000000
RESET# 00000000000000000000000000000000
00000000000000000000000000000000
00000000000000000000000000000000
Tvdd2rst#
Vdd
Figure 1. Power Up Timing
BIT_CLK
SYNC
Tsync2crd
CODEC_READY
Figure 2. Codec Ready from Start-up or Fault Condition
BIT_CLK
Torise
Tifall
Tclk_high Tclk_low
Tclk_period
SYNC
Tirise
Tsync_high
Tifall
Tsync_low
Tsync_period
Figure 3. Clocks
10
DS549PP1
CS4202
BIT_CLK
SDATA_IN
Tco
SDATA_OUT,
SYNC
Tisetup
Tihold
Figure 4. Data Setup and Hold
BIT_CLK
Slot 1
SDATA_OUT Write to 0x20
Slot 2
Data PR4
Don't Care
Ts2_pdown
SDATA_IN
SYNC
Tsync_pr4
Tsync2clk
Figure 5. PR4 Powerdown and Warm Reset
RESET#
Tsetup2rst
SDATA_OUT,
SYNC
Toff
SDATA_IN,
Hi-Z
BIT_CLK
Figure 6. Test Mode
DS549PP1
11
CS4202
2. GENERAL DESCRIPTION
2.1
The CS4202 is a mixed-signal serial audio codec
with integrated headphone power amplifier compliant with the Intel® Audio Codec ’97 Specification, revision 2.2 [6] (referred to as AC ’97). It is
designed to be paired with a digital controller, typically located on the PCI bus or integrated within
the system core logic chip set. The controller is responsible for all communications between the
CS4202 and the remainder of the system. The
CS4202 contains two distinct functional sections:
digital and analog. The digital section includes the
AC-link interface, S/PDIF interface, serial data
port, GPIO, power management support, and Sample Rate Converters (SRCs). The analog section includes the analog input multiplexer (mux), stereo
input mixer, stereo output mixer, mono output mixer, headphone amplifier, stereo Analog-to-Digital
Converters (ADCs), stereo Digital-to-Analog Converters (DACs), and their associated volume controls.
All communication with the CS4202 is established
with a 5-wire digital interface to the controller
called the AC-link. This interface is shown in
Figure 7. All clocking for the serial communication
is synchronous to the BIT_CLK signal. BIT_CLK
is generated by the primary audio codec and is used
to clock the controller and any secondary audio codecs. Both input and output AC-link audio frames
are organized as a sequence of 256 serial bits forming 13 groups referred to as ‘slots’. During each audio frame, data is passed bi-directionally between
the CS4202 and the controller. The input frame is
driven from the CS4202 on the SDATA_IN line.
The output frame is driven from the controller on
the SDATA_OUT line. The controller is also responsible for issuing reset commands via the RESET# signal. Following a Cold Reset, the CS4202
is responsible for notifying the controller that it is
ready for operation after synchronizing its internal
functions. The CS4202 AC-link signals must use
the same digital supply voltage as the controller, either +5 V or +3.3 V. See Section 3, AC-Link Frame
Definition, for detailed AC-link information.
Digital AC'97
Controller
SYNC
AC-Link
AC'97
CODEC
BIT_CLK
SDATA_OUT
SDATA_IN
RESET#
Figure 7. AC-link Connections
12
DS549PP1
CS4202
2.2
Control Registers
The CS4202 contains a set of AC ’97 compliant
control registers, and a set of Cirrus Logic defined
control registers. These registers control the basic
functions and features of the CS4202. Read accesses of the control registers by the AC ’97 controller
are accomplished with the requested register index
in Slot 1 of a SDATA_OUT frame. The following
SDATA_IN frame will contain the read data in Slot
2. Write operations are similar, with the register index in Slot 1 and the write data in Slot 2 of a
SDATA_OUT frame. The function of each input
and output frame is detailed in Section 3, AC-Link
Frame Definition. Individual register descriptions
are found in Section 4, Register Interface.
2.3
Sample Rate Converters
The sample rate converters (SRC) provide high accuracy digital filters supporting sample frequencies
other than 48 kHz to be captured from the CS4202
or played from the controller. AC ’97 requires support for two audio rates (44.1 and 48 kHz). In addition, the Intel® I/O Controller Hub (ICHx)
specification [9] requires support for five more audio rates (8, 11.025, 16, 22.05, and 32 kHz). The
CS4202 supports all these rates, as shown in
Table 10 on page 32.
2.4
Mixers
The CS4202 input and output mixers are illustrated
in Figure 8. The stereo input mixer sums together
DS549PP1
the analog inputs to the CS4202 according to the
settings in the volume control registers. The stereo
output mixer sums the output of the stereo input
mixer with the PC_BEEP and PHONE signals. The
stereo output mix is then sent to the LINE_OUT
and HP_OUT pins of the CS4202. The mono output mixer generates a monophonic sum of the left
and right audio channels from the stereo input mixer. The mono output mix is then sent to the
MONO_OUT pin on the CS4202.
2.5
Input Mux
The input multiplexer controls which analog input
is sent to the ADCs. The output of the input mux is
converted to stereo 18-bit digital PCM data and
transmitted to the controller by means of the
AC-link SDATA_IN signal.
2.6
Volume Control
The CS4202 volume registers control analog input
levels to the input mixer and analog output levels,
including the master volume level. The PC_BEEP
volume control uses 3 dB steps with a range of 0 dB
to -45 dB attenuation. All other analog volume controls use 1.5 dB steps. The analog inputs have a
mixing range of +12 dB signal gain to -34.5 dB signal attenuation. The analog output volume controls
have a range of 0 dB to -46.5 dB attenuation for
LINE_OUT, HP_OUT and MONO_OUT.
13
CS4202
PC BEEP BYPASS
MUTE
VOL
MUTE
VOL
MUTE
VOL
PHONE
VOL
PC_BEEP
MUTE
MAIN D/A
CONVERTERS
PCM_OUT
MIC1
MIC2
DAC DIRECT
MODE
ANALOG STEREO
INPUT MIXER
MUTE
Σ
Σ
MASTER
VOLUME
VOL
MUTE
VOL
CD
BOOST
VOL
LINE
DAC
MIC
SELECT
ANALOG STEREO
OUTPUT MIXER
LINE OUT
MUTE
OUTPUT
BUFFER
MUTE
HEADPHONE
AMPLIFIER
MUTE
OUTPUT
BUFFER
HEADPHONE
VOLUME
HEADPHONE OUT
VOL
MUTE
VOL
AUX
VOL
VIDEO
MUTE
MONO MIX
SELECT
STEREO TO
MONO MIXER
Σ
MONO OUT
SELECT
MONO OUT
VOL
1/2
STEREO TO
MONO MIXER
MONO
VOLUME
Σ
1/2
MAIN ADC
GAIN
PCM_IN
VOL
ADC
INPUT
MUX
MAIN A/D
CONVERTERS
MUTE
ADC
Figure 8. CS4202 Mixer Diagram
14
DS549PP1
CS4202
within the frame. The first bit position in a new serial data frame is F0 and the last bit position in the
serial data frame is F255. When SYNC goes active
(high) and is sampled active by the CS4202 (on the
falling edge of BIT_CLK), both devices are synchronized to a new serial data frame. The data on
the SDATA_OUT pin at this clock edge is the final
bit of the previous frame’s serial data. On the next
rising edge of BIT_CLK, the first bit of Slot 0 is
driven by the controller on the SDATA_OUT pin.
On the next falling edge of BIT_CLK, the CS4202
latches this data in as the first bit of the frame.
3. AC-LINK FRAME DEFINITION
The AC-link is a bi-directional serial port with data
organized into frames consisting of one 16-bit and
twelve 20-bit time-division multiplexed slots.
Slot 0 is a special reserved time slot containing
16-bits which are used for AC-link protocol infrastructure. Slots 1 through 12 contain audio or control/status data. Both the serial data output and
input frames are defined from the controller perspective, not from the CS4202 perspective.
The controller synchronizes the beginning of a
frame with the assertion of the SYNC signal.
Figure 9 shows the position of each bit location
20.8 µ s
(48 kHz)
Tag Phase
Data Phase
SYNC
12.288 MHz
81.4 ns
BIT_CLK
Bit Frame Position:
F255
SDATA_OUT
0
Bit Frame Position:
F255
SDATA_IN
GPIO
INT
F0
Valid
Frame
F0
Codec
Ready
F1
F2
Slot 1
Valid
Slot 2
Valid
F13
F14
Slot 12
Valid
F12
0
Codec
ID1
F1
F2
F12
F13
F14
Slot 1
Valid
Slot 2
Valid
Slot 12
Valid
0
0
Slot 0
F15
F16
F35
F36
F56
F57
F76
F96
F255
Codec
ID0
R/W
0
WD15
D19
D18
D19
D19
0
F15
F16
F35
F36
F56
0
0
RD15
D19
0
Slot 1
Slot 2
F57
D18
Slot 3
F76
F96
D19
D19
Slot 4
F255
GPIO
INT
Slots 5-12
Figure 9. AC-link Input and Output Framing
DS549PP1
15
CS4202
3.1
AC-Link Serial Data Output Frame
In the serial data output frame, data is passed on the SDATA_OUT pin to the CS4202 from the AC ’97
controller. Figure 9 illustrates the serial port timing.
The PCM playback data being passed to the CS4202 is shifted out MSB first in the most significant bits
of each slot. Any PCM data from the AC ’97 controller that is not 20 bits wide should be left justified in
its corresponding slot and dithered or zero-padded in the unused bit positions.
Bits that are reserved should always be ‘cleared’ by the AC ’97 controller.
3.1.1
Serial Data Output Slot Tags (Slot 0)
Bit 15
14
13
12
11
10
9
8
7
6
5
4
3
Valid Slot 1 Slot 2 Slot 3 Slot 4
Not
Slot 6 Slot 7 Slot 8 Slot 9 Slot 10 Slot 11 Slot 12
Frame Valid Valid Valid Valid Implem Valid Valid Valid Valid Valid Valid Valid
2
1
0
Codec Codec
ID1
ID0
Res
Valid Frame
The Valid Frame bit determines if any of the following slots contain either valid playback data
for the CS4202 or data for read/write operations. When ‘set’, at least one of the other AC-link
slots contains valid data. If this bit is ‘clear’, the remainder of the frame is ignored.
Slot 1 Valid
The Slot 1 Valid bit indicates a valid register read/write address for a primary codec.
Slot 2 Valid
The Slot 2 Valid bit indicates valid register write data for a primary codec.
Slot [3:4,6:11] Valid
The Slot [3:4,6:11] Valid bits indicate the validity of data in their corresponding serial data output slots. If a bit is ‘set’, the corresponding output slot contains valid data. If a bit is ‘cleared’,
the corresponding slot will be ignored.
Slot 12 Valid
The Slot 12 Valid bit indicates if output Slot 12 contains valid GPIO control data.
Codec ID[1:0]
The Codec ID[1:0] bits determine which codec is being accessed during the current AC-link
frame. Codec ID[1:0] = 00 indicates the primary codec is being accessed. Codec ID[1:0] = 01,
10, or 11 indicates one of three possible secondary codecs is being accessed. A Codec ID
value of 01, 10, or 11 also indicates a valid read/write address and/or valid register write data
for a secondary codec.
3.1.2
Bit 19
R/W
Command Address Port (Slot 1)
18
RI6
17
RI5
16
RI4
15
RI3
14
RI2
13
RI1
12
RI0
11
10
9
8
7
6
5
Reserved
4
3
2
1
0
R/W
Read/Write. When this bit is ‘set’, a read of the AC ’97 register specified by the register index
bits will occur in the AC ’97 2.x audio codec. When the bit is ‘cleared’, a write will occur. For
any read or write access to occur, the Valid Frame bit (F0) must be ‘set’ and the Codec ID[1:0]
bits (F[14:15]) must match the Codec ID of the AC ’97 2.x audio codec being accessed. Additionally, for a primary codec, the Slot 1 Valid bit (F1) must be ‘set’ for a read access and
both the Slot 1 Valid bit (F1) and the Slot 2 Valid bit (F2) must be ‘set’ for a write access. For
a secondary codec, both the Slot 1 Valid bit (F1) and the Slot 2 Valid bit (F2) must be ‘cleared’
for read and write accesses. See Figure 9 for bit frame positions.
RI[6:0]
Register Index. The RI[6:0] bits contain the 7-bit register index to the AC ’97 registers in the
CS4202. All registers are defined at word addressable boundaries. The RI0 bit must be ‘clear’
to access CS4202 registers.
16
DS549PP1
CS4202
3.1.3
Command Data Port (Slot 2)
Bit 19 18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
WD15 WD14 WD13 WD12 WD11 WD10 WD9 WD8 WD7 WD6 WD5 WD4 WD3 WD2 WD1 WD0
3
2 1 0
Reserved
WD[15:0]
Write Data. The WD[15:0] bits contain the 16-bit value to be written to the register. If an access is a read, this slot is ignored.
NOTE:
For any write to an AC ’97 register, the write is defined to be an ‘atomic’ access. This means
that when the Slot 1 Valid bit in output Slot 0 is ‘set’, the Slot 2 Valid bit in output Slot 0 should
always be ‘set’ during the same audio frame. No write access may be split across 2 frames.
3.1.4
PCM Playback Data (Slots 3-4,6-11)
Bit 19 18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
PD19 PD18 PD17 PD16 PD15 PD14 PD13 PD12 PD11 PD10 PD9 PD8 PD7 PD6 PD5 PD4 PD3 PD2 PD1 PD0
PD[19:0]
3.1.5
Playback Data. The PD[19:0] bits contain the 20-bit PCM (2’s complement) playback data for
the left and right DACs, serial data ports, and/or the S/PDIF transmitter. Table 8 on page 30
lists a cross reference for each function and its respective slot. The mapping of a given slot
to the DAC, serial data port, or S/PDIF transmitter is determined by the state of the DSA[1:0]
bits in the Extended Audio ID Register (Index 28h) and the SPSA[1:0] bits in the Extended
Audio Status/Control Register (Index 2Ah).
GPIO Pin Control (Slot12)
Bit 19 18
GPIO[4:0]
DS549PP1
17
16
15 14 13
Not Implemented
12
11
10
9
8
7
6
5
4
GPIO4 GPIO3 GPIO2 GPIO1 GPIO0
3
2
1
Reserved
0
GPIO Pin Control. The GPIO[4:0] bits control the CS4202 GPIO pins configured as outputs.
Write accesses using GPIO pin control bits configured as outputs will be reflected on the
GPIO pin output on the next AC-link frame. Write accesses using GPIO pin control bits configured as inputs will have no effect and are ignored. If the GPOC bit in the Misc. Crystal Control Register (Index 60h) is ‘set’, the bits in output Slot 12 are ignored and GPIO pins
configured as outputs are controlled through the GPIO Pin Status Register (Index 54h).
17
CS4202
3.2
AC-Link Serial Data Input Frame
In the serial data input frame, data is passed on the SDATA_IN pin from the CS4202 to the AC ’97 controller. The data format for the input frame is very similar to the output frame. Figure 9 on page 15 illustrates the serial port timing.
The PCM capture data from the CS4202 is shifted out MSB first in the most significant 18 bits of each slot.
The least significant 2 bits in each slot will be ‘cleared’. If the host requests PCM data from the AC ’97
Controller that is less than 18 bits wide, the controller should dither and round or just round (but not truncate) to the desired bit depth.
Bits that are reserved or not implemented in the CS4202 will always be returned ‘cleared’.
3.2.1
Serial Data Input Slot Tag Bits (Slot 0)
Bit 15
14
13
12
11
Codec Slot 1 Slot 2 Slot 3 Slot 4
Ready Valid Valid Valid Valid
10
0
9
8
7
Slot 6 Slot 7 Slot 8
Valid Valid Valid
6
5
0
0
4
3
Slot 11 Slot 12
Valid Valid
2
1
0
Reserved
Codec Ready
Codec Ready. The Codec Ready bit indicates the readiness of the CS4202 AC-link. Immediately after a Cold Reset this bit will be ‘clear’. Once the CS4202 clocks and voltages are stable, this bit will be ‘set’. Until the Codec Ready bit is ‘set’, no AC-link transactions should be
attempted by the controller. The Codec Ready bit does not indicate readiness of the DACs,
ADCs, Vref, or any other analog function. Those must be checked in the Powerdown Control/Status Register (Index 26h) by the controller before any access is made to the mixer registers. Any accesses to the CS4202 while Codec Ready is ‘clear’ are ignored.
Slot 1 Valid
The Slot 1 Valid bit indicates Slot 1 contains a valid read back address.
Slot 2 Valid
The Slot 2 Valid bit indicates Slot 2 contains valid register read data.
Slot [3:4,6:8,11] Valid The Slot [3:4,6:8,11] Valid bits indicate Slot [3:4,6:8,11] contains valid capture data from the
CS4202 ADCs. If a bit is ‘set’, the corresponding input slot contains valid data. If a bit is
‘cleared’, the corresponding slot will be ignored.
Slot 12 Valid
3.2.2
The Slot 12 Valid bit indicates Slot 12 contains valid GPIO status data.
Status Address Port (Slot 1)
Bit 19 18
Res RI6
17
RI5
16
RI4
15
RI3
14
RI2
13
RI1
12
RI0
11
10
SR3 SR4
9
0
8
7
6
5
4
3
SR6 SR7 SR8 SR9 SR10 SR11
2
0
1
0
Reserved
RI[6:0]
Register Index. The RI[6:0] bits echo the AC ’97 register address when a register read has
been requested in the previous frame. The CS4202 will only echo the register index for a read
access. Write accesses will not return valid data in Slot 1.
SR[3:4,6:11]
Slot Request. If SRx is ‘set’, this indicates the CS4202 SRC does not need a new sample on
the next AC-link frame for that particular slot. If SRx is ‘clear’, the SRC indicates a new sample
is needed on the following frame. If the VRA bit in the Extended Audio Status/Control Register
(Index 2Ah) is ‘clear’, the SR[3:4,6:11] bits are always 0. When VRA is ‘set’, the SRC is enabled and the SR[3:4,6:11] bits are used to request data.
18
DS549PP1
CS4202
3.2.3
Status Data Port (Slot 2)
Bit 19 18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
RD15 RD14 RD13 RD12 RD11 RD10 RD9 RD8 RD7 RD6 RD5 RD4 RD3 RD2 RD1 RD0
RD[15:0]
3.2.4
3
2
1
0
Reserved
Read Data. The RD[15:0] bits contain the register data requested by the controller from the
previous read request. All read requests will return the read address in the input Slot 1 and
the register data in the input Slot 2 on the following serial data frame.
PCM Capture Data (Slot 3-4,6-8,11)
Bit 19 18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
CD17 CD16 CD15 CD14 CD13 CD12 CD11 CD10 CD9 CD8 CD7 CD6 CD5 CD4 CD3 CD2 CD1 CD0
CD[17:0]
1
0
0
0
Capture Data. The CD [17:0] bits contain 18-bit PCM (2’s complement) capture data. The
data will only be valid when the respective slot valid bit is ‘set’ in input Slot 0. The mapping of
a given slot to an ADC is determined by the state of the ASA[1:0] bits in the AC Mode Control
Register (index 5Eh). The definition of each slot can be found in Table 8 on page 30.
3.2.5 GPIO Pin Status (Slot 12)
Bit 19 18
0
0
17
16
15
14
13
12
11
10
9
0
0
0
0
0
0
0
0
0
8
7
6
5
4
3
2
1
0
GPIO
GPIO4 GPIO3 GPIO2 GPIO1 GPIO0 Res BDI Res
_INT
GPIO[4:0]
GPIO Pin Status. The GPIO[4:0] bits reflect the status of the CS4202 GPIO pins configured
as inputs. The pin status of GPIO pins configured as outputs will be reflected back on the
GPIO[4:0] bits of input Slot 12 in the next frame. The output GPIO pins are controlled by the
GPIO[4:0] pin control bits in output Slot 12.
BDI
BIOS-Driver Interface. The BDI bit indicates that a BIOS event has occurred. This bit is a logic
OR of all bits in the BDI Status Register (Index 7Ah) ANDed with their corresponding bit in the
BDI Config Register (Index 70h).
GPIO_INT
GPIO Interrupt. The GPIO_INT bit indicates that a GPIO or BDI interrupt event has occurred.
The occurrence of a GPIO interrupt is determined by the GPIO interrupt requirements as outlined in the GPIO Pin Wakeup Mask Register (Index 52h) description. In this case, the
GPIO_INT bit is cleared by writing a ‘0’ to the bit in the GPIO Pin Status Register (Index 54h)
corresponding to the GPIO pin which generated the interrupt.
The occurrence of a BDI interrupt is determined by the BDI interrupt requirements as outlined
in the BDI Control Registers (Index 70h - 72h). In this case, the GPIO_INT bit is cleared by
writing a ‘0’ to the bit in the BDI Status Register (Index 7Ah) that generated the interrupt.
DS549PP1
19
CS4202
3.3
AC-Link Protocol Violation - Loss of
SYNC
The CS4202 is designed to handle SYNC protocol
violations. The following are situations where the
SYNC protocol has been violated:
•
The SYNC signal is not sampled high for exactly 16 BIT_CLK clock cycles at the start of an
audio frame.
•
The SYNC signal is not sampled high on the
256th BIT_CLK clock period after the previous
SYNC assertion.
20
•
The SYNC signal goes active high before the
256th BIT_CLK clock period after the previous
SYNC assertion.
Upon loss of synchronization with the controller,
the CS4202 will ‘clear’ the Codec Ready bit in the
serial data input frame until two valid frames are
detected. During this detection period, the CS4202
will ignore all register reads and writes and will
discontinue the transmission of PCM capture data.
In addition, if the LOSM bit in the Misc. Crystal
Control Register (Index 60h) is ‘set’ (default), the
CS4202 will mute all analog outputs. If the LOSM
bit is ‘clear’, the analog outputs will not be muted.
DS549PP1
CS4202
4. REGISTER INTERFACE
Reg
Register Name
D8
D7
D6
D5
D4
D3
D2
D1
D0
Default
0
0
0
0
0
0
0
ID8
ID7
0
0
ID4
0
0
0
0
0190h
02h Master Volume
Mute
0
ML5
ML4
ML3
ML2
ML1
ML0
0
0
MR5
MR4
MR3
MR2
MR1
MR0
8000h
04h Headphone Volume
Mute
0
ML5
ML4
ML3
ML2
ML1
ML0
0
0
MR5
MR4
MR3
MR2
MR1
MR0
8000h
06h Mono Volume
Mute
0
0
0
0
0
0
0
0
0
MM5
MM4
MM3
MM2
MM1
MM0
8000h
0Ah PC_BEEP Volume
Mute
0
0
0
0
0
0
0
0
0
0
PV3
PV2
PV1
PV0
0
0000h
0Ch Phone Volume
Mute
0
0
0
0
0
0
0
0
0
0
GN4
GN3
GN2
GN1
GN0
8008h
0Eh Mic Volume
Mute
0
0
0
0
0
0
0
0
20dB
0
GN4
GN3
GN2
GN1
GN0
8008h
10h Line In Volume
Mute
0
0
GL4
GL3
GL2
GL1
GL0
0
0
0
GR4
GR3
GR2
GR1
GR0
8808h
12h CD Volume
Mute
0
0
GL4
GL3
GL2
GL1
GL0
0
0
0
GR4
GR3
GR2
GR1
GR0
8808h
14h Video Volume
Mute
0
0
GL4
GL3
GL2
GL1
GL0
0
0
0
GR4
GR3
GR2
GR1
GR0
8808h
16h Aux Volume
Mute
0
0
GL4
GL3
GL2
GL1
GL0
0
0
0
GR4
GR3
GR2
GR1
GR0
8808h
18h PCM Out Volume
Mute
0
0
GL4
GL3
GL2
GL1
GL0
0
0
0
GR4
GR3
GR2
GR1
GR0
8808h
0
0
0
0
0
SL2
SL1
SL0
0
0
0
0
0
SR2
SR1
SR0
0000h
Mute
0
0
0
GL3
GL2
GL1
GL0
0
0
0
0
GR3
GR2
GR1
GR0
8000h
0
0
0
0
0
0
MIX
MS
LPBK
0
0
0
0
0
0
0
0000h
EAPD
PR6
PR5
PR4
PR3
PR2
PR1
PR0
0
0
0
0
REF
ANL
DAC
ADC
000Fh
ID1
ID0
0
0
0
0
0
DSA1 DSA0
0
SPDIF
0
VRA
x605h
0
0
0
0
0
0
0
SPSA1 SPSA0
0
SPDIF
0
VRA
0410h
00h Reset
1Ah Record Select
1Ch Record Gain
20h General Purpose
26h Powerdown Ctrl/Stat
28h Ext’d Audio ID
2Ah Ext’d Audio Stat/Ctrl
D15 D14
D13
D12 D11 D10 D9
REV1 REV0 AMAP
0
SPCV
0
2Ch PCM Front DAC Rate
SR15 SR14
SR13
SR12 SR11 SR10 SR9
SR8
SR7
SR6
SR5
SR4
SR3
SR2
SR1
SR0
BB80h
32h PCM L/R ADC Rate
SR15 SR14
SR13
SR12 SR11 SR10 SR9
SR8
SR7
SR6
SR5
SR4
SR3
SR2
SR1
SR0
BB80h
PRO
2000h
3Ah S/PDIF Control
V
DRS
3Ch Ext’d Modem ID
ID1
ID0
0
3Eh Ext’d Modem Stat/Ctrl
0
0
4Ch GPIO Pin Config.
0
4Eh GPIO Pin Polarity/Type
1
L
CC6
CC5
CC4
CC3
CC2
CC1
CC0
PRE
0
0
0
0
0
0
0
0
0
0
0
0
0
x000h
0
0
0
0
0
PRA
0
0
0
0
0
0
0
GPIO
0100h
0
0
0
0
0
0
0
0
0
0
GC4
GC3
GC2
GC1
GC0
001Fh
1
1
1
1
1
1
1
1
1
1
GP4
GP3
GP2
GP1
GP0
FFFFh
SPSR1 SPSR0
COPY /AUDIO
50h GPIO Pin Sticky
0
0
0
0
0
0
0
0
0
0
0
GS4
GS3
GS2
GS1
GS0
0000h
52h GPIO Pin Wakeup
0
0
0
0
0
0
0
0
0
0
0
GW4
GW3
GW2
GW1
GW0
0000h
54h GPIO Pin Status
0
0
0
0
0
0
0
0
0
0
0
GI4
GI3
GI2
GI1
GI0
0000h
0
0
ASA1
ASA0
0
0
0
0
0
GPOC
SDO2 SDSC
Cirrus Logic Defined Registers:
5Eh AC Mode Control
0
0
0
0
ASPM
0
TMM DDM
60h Misc. Crystal Control
0
0
0
DPC
0
0
Reserved
SDEN
0
0
0
0
0
0
0
0
0
0
0
70h BDI Config
E15
E14
E13
E12
E11
E10
E9
E8
E7
E6
E5
E4
E3
72h BDI Wakeup
E15
E14
E13
E12
E11
E10
E9
E8
E7
E6
E5
E4
7Ah BDI Status
E15
E14
E13
E12
E11
E10
E9
E8
E7
E6
E5
7Ch Vendor ID1
F7
F6
F5
F4
F3
F2
F1
F0
S7
S6
7Eh Vendor ID2
T7
T6
T5
T4
T3
T2
T1
T0
0
DID2
6Ah Serial Port Control
10dB CRST
0
0000h
LOSM
0003h
SDF1
SDF0
0000h
E2
E1
E0
0000h
E3
E2
E1
E0
0000h
E4
E3
E2
E1
E0
0000h
S5
S4
S3
S2
S1
S0
4352h
DID1
DID0
0
REV2
REV1
REV0
5971h
Reserved
Table 1. Register Overview for the CS4202
DS549PP1
21
CS4202
4.1
D15
0
Reset Register (Index 00h)
D14
0
D13
0
D12
0
D11
0
D10
0
D9
0
D8
ID8
D7
ID7
D6
0
D5
0
D4
ID4
D3
0
D2
0
D1
0
D0
0
ID8
18-bit ADC Resolution. The ID8 bit is ‘set’, indicating this feature is present.
ID7
20-bit DAC resolution. The ID7 bit is ‘set’, indicating this feature is present.
ID4
Headphone Out. The ID4 bit is ‘set’, indicating this feature is present. The state of this bit depends on the state of the HPCFG pin.
Default
0190h. The data in this register is read-only data.
Any write to this register causes a Register Reset of the audio control (Index 00h - 3Ah) and Cirrus Logic defined
(Index 5Ah - 7Ah) registers. A read from this register returns configuration information about the CS4202.
4.2
D15
Mute
Analog Mixer Output Volume Registers (Index 02h - 04h)
D14
0
D13
ML5
D12
ML4
D11
ML3
D10
ML2
D9
ML1
D8
ML0
D7
0
D6
0
D5
MR5
D4
MR4
D3
MR3
D2
MR2
D1
MR1
D0
MR0
Mute
Output Mute. Setting this bit mutes the LINE_OUT_L/R or HP_OUT_L/R output signals.
ML[5:0]
Output Volume Left. These bits control the left output volume. Each step corresponds to 1.5
dB gain adjustment, with a total available range from 0 dB to -46.5 dB attenuation. Setting the
ML5 bit sets the left channel attenuation to -46.5 dB by forcing ML[4:0] to a ‘1’ state. ML[5:0]
will read back 011111 when ML5 has been ‘set’. See Table 2 for further details.
MR[5:0]
Output Volume Right. These bits control the right output volume. Each step corresponds to
1.5 dB gain adjustment, with a total available range from 0 dB to -46.5 dB attenuation. Setting
the MR5 bit sets the right channel attenuation to -46.5 dB by forcing MR[4:0] to a ‘1’ state.
MR[5:0] will read back 011111 when MR5 has been ‘set’. See Table 2 for further details.
Default
8000h. This value corresponds to 0 dB attenuation and Mute ‘set’.
If the HPCFG pin is left floating, register 02h controls the Master Output Volume and register 04h controls the Headphone Output Volume. If the HPCFG pin is tied ‘low’, register 02h controls the Headphone Volume and register 04h
is a read-only register and always returns 0000h when ‘read’.
Mx5 - Mx0
Write
Mx5 - Mx0
Read
Gain
Level
000000
000000
0 dB
000001
000001
-1.5 dB
…
…
...
011111
011111
-46.5 dB
100000
011111
-46.5 dB
...
...
...
111111
011111
-46.5 dB
Table 2. Analog Mixer Output Attenuation
22
DS549PP1
CS4202
4.3
Mono Volume Register (Index 06h)
D15
Mute
D14
0
D13
0
D12
0
D11
0
D10
0
D9
0
D8
0
D7
0
D6
0
D5
MM5
D4
MM4
D3
MM3
D2
MM2
D1
MM1
D0
MM0
Mute
Mono Mute. Setting this bit mutes the MONO_OUT output signal.
MM[5:0]
Mono Volume Control. The MM[5:0] bits control the mono output volume. Each step corresponds to 1.5 dB gain adjustment, with a total available range from 0 dB to -46.5 dB attenuation. Setting the MM5 bit sets the mono attenuation to -46.5 dB by forcing MM[4:0] to a ‘1’
state. MM[5:0] will read back 011111 when MM5 has been ‘set’. See Table 2 on page 22 for
further attenuation levels.
Default
8000h. This value corresponds to 0 dB attenuation and Mute ‘set’.
4.4
D15
Mute
PC_BEEP Volume Register (Index 0Ah)
D14
0
D13
0
D12
0
D11
0
D10
0
D9
0
D8
0
D7
0
D6
0
D5
0
D4
PV3
D3
PV2
D2
PV1
D1
PV0
D0
0
Mute
PC_BEEP Mute. Setting this bit mutes the PC_BEEP input signal.
PV[3:0]
PC_BEEP Volume Control. The PV[3:0] bits control the gain levels of the PC_BEEP input
source to the Input Mixer. Each step corresponds to 3 dB gain adjustment, with 0000 = 0 dB.
The total range is 0 dB to -45 dB attenuation.
Default
0000h. This value corresponds to 0 dB attenuation and Mute ‘clear’.
This register has no effect on the PC_BEEP volume during RESET#.
4.5
D15
Mute
Phone Volume Register (Index 0Ch)
D14
0
D13
0
D12
0
D11
0
D10
0
D9
0
D8
0
D7
0
D6
0
D5
0
D4
GN4
D3
GN3
D2
GN2
D1
GN1
D0
GN0
Mute
Phone Mute. Setting this bit mutes the Phone input signal.
GN[5:0]
Phone Volume Control. The GN[4:0] bits control the gain level of the Phone input source to
the Input Mixer. Each step corresponds to 1.5 dB gain adjustment, with 01000 = 0 dB. The
total range is +12 dB to -34.5 dB attenuation. See Table 4 on page 25 for further attenuation
levels.
Default
8008h. This value corresponds to 0 dB attenuation and Mute ‘set’.
DS549PP1
23
CS4202
4.6
D15
Mute
Microphone Volume Register (Index 0Eh)
D14
0
D13
0
D12
0
D11
0
D10
0
D9
0
D8
0
D7
0
D6
20dB
D5
0
D4
GN4
D3
GN3
D2
GN2
D1
GN1
D0
GN0
Mute
Microphone Mute. Setting this bit mutes the MIC1 or MIC2 signal. The selection of the MIC1
or MIC2 input pin is controlled by the MS bit in the General Purpose Register (Index 20h).
20dB
Microphone 20 dB Boost. When ‘set’, the 20dB bit enables the +20 dB microphone boost
block. In combination with the 10dB boost bit in the Misc. Crystal Control Register (Index 60h)
this bit allows for variable boost from 0 dB to +30 dB in steps of 10 dB. Table 3 summarizes
this behavior.
GN[4:0]
Microphone Volume Control. The GN[4:0] bits are used to control the gain level of the Microphone input source to the Input Mixer. Each step corresponds to 1.5 dB gain adjustment, with
01000 = 0 dB. The total range is +12 dB to -34.5 dB gain. See Table 3 for further details.
Default
8008h. This value corresponds to 0 dB gain and Mute ‘set’.
Gain Level
GN4 - GN0
10dB = 0,
20dB = 0
10dB = 1,
20dB = 0
10dB = 0,
20dB = 1
10dB = 1,
20dB = 1
00000
+12.0 dB
+22.0 dB
+32.0 dB
+42.0 dB
00001
+10.5 dB
+20.5 dB
+30.5 dB
+40.5 dB
…
…
...
...
...
00111
+1.5 dB
+11.5 dB
+21.5 dB
+31.5 dB
01000
0.0 dB
+10.0 dB
+20.0 dB
+30.0 dB
01001
-1.5 dB
+8.5 dB
+18.5 dB
+28.5 dB
…
…
...
...
...
11111
-34.5 dB
-24.5 dB
-14.5 dB
-4.5 dB
Table 3. Microphone Input Gain Values
24
DS549PP1
CS4202
4.7
D15
Mute
Analog Mixer Input Gain Registers (Index 10h - 18h)
D14
0
D13
0
D12
GL4
D11
GL3
D10
GL2
D9
GL1
D8
GL0
D7
0
D6
0
D5
0
D4
GR4
D3
GR3
D2
GR2
D1
GR1
D0
GR0
Mute
Stereo Input Mute. Setting this bit mutes the respective input signal, both right and left inputs.
GL[4:0]
Left Volume Control. The GL[4:0] bits are used to control the gain level of the left analog input
source to the Input Mixer. Each step corresponds to 1.5 dB gain adjustment, with
01000 = 0 dB. The total range is +12 dB to -34.5 dB gain. See Table 4 for further details.
GR[4:0]
Right Volume Control. The GR[4:0] bits are used to control the gain level of the right analog
input source to the Input Mixer. Each step corresponds to 1.5 dB gain adjustment, with
01000 = 0 dB. The total range is +12 dB to -34.5 dB gain. See Table 4 for further details.
Default
8808h. This value corresponds to 0 dB gain and Mute ‘set’.
The Analog Mixer Input Gain Registers are listed in Table 5.
Gx4 - Gx0 Gain Level
00000
+12.0 dB
00001
+10.5 dB
…
…
00111
+1.5 dB
01000
0.0 dB
01001
-1.5 dB
…
…
11111
-34.5 dB
Table 4. Analog Mixer Input Gain Values
Register Index
Function
10h
Line In Volume
12h
CD Volume
14h
Video Volume
16h
Aux Volume
18h
PCM Out Volume
Table 5. Analog Mixer Input Gain Register Index
DS549PP1
25
CS4202
4.8
D15
0
Input Mux Select Register (Index 1Ah)
D14
0
D13
0
D12
0
D11
0
D10
SL2
D9
SL1
D8
SL0
D7
0
D6
0
D5
0
D4
0
D3
0
D2
SR2
D1
SR1
D0
SR0
SL[2:0]
Left Channel Source. The SL[2:0] bits select the left channel source to pass to the ADCs for
recording. See Table 6 for possible values.
SR[2:0]
Right Channel Source. The SR[2:0] bits select the right channel source to pass to the ADCs
for recording. See Table 6 for possible values.
Default
0000h. This value selects the Mic input for both channels.
Sx2 - Sx0
Record Source
000
Mic
001
CD Input
010
Video Input
011
Aux Input
100
Line Input
101
Stereo Mix
110
Mono Mix
111
Phone Input
Table 6. Input Mux Selection
26
DS549PP1
CS4202
4.9
D15
Mute
Record Gain Register (Index 1Ch)
D14
0
D13
0
D12
0
D11
GL3
D10
GL2
D9
GL1
D8
GL0
D7
0
D6
0
D5
0
D4
0
D3
GR3
D2
GR2
D1
GR1
D0
GR0
Mute
Record Gain Mute. Setting this bit mutes the input to the L/R ADCs.
GL[3:0]
Left ADC Gain. The GL[3:0] bits control the input gain on the left channel of the analog
source, applied after the input mux and before the ADCs. Each step corresponds to 1.5 dB
gain adjustment, with 0000 = 0 dB. The total range is 0 dB to +22.5 dB gain. See Table 7 for
further details.
GR[3:0]
Right ADC Gain. The GR[3:0] bits control the input gain on the right channel of the analog
source, applied after the input mux and before the ADCs. Each step corresponds to 1.5 dB
gain adjustment, with 0000 = 0 dB. The total range is 0 dB to +22.5 dB gain. See Table 7 for
further details.
Default
8000h. This value corresponds to 0 dB gain and Mute ‘set’.
Gx3 - Gx0 Gain Level
1111
+22.5 dB
…
…
0001
+1.5 dB
0000
0 dB
Table 7. Record Gain Values
DS549PP1
27
CS4202
4.10
D15
0
General Purpose Register (Index 20h)
D14
0
D13
0
D12
0
D11
0
D10
0
D9
MIX
D8
MS
D7
LPBK
D6
0
D5
0
D4
0
D3
0
D2
0
D1
0
D0
0
MIX
Mono Output Path. This bit controls the source of the mono output driver. When ‘clear’, the
output of the stereo-to-mono mixer is sent to the mono output. When ‘set’, the output of the
microphone boost stage is sent to the mono output. The source of the stereo-to-mono mixer
is controlled by the TMM bit in the AC Mode Control Register (Index 5Eh). The source of the
microphone boost stage is controlled by the MS bit in the General Purpose Register
(Index 20h).
MS
Microphone Select. The MS bit determines which of the two Mic inputs are passed to the mixer. When ‘set’, the MIC2 input is selected. When ‘clear’, the MIC1 input is selected.
LPBK
Loopback Enable. When ‘set’, the LPBK bit enables the ADC/DAC Loopback Mode. This bit
routes the output of the ADCs to the input of the DACs without involving the AC-link.
Default
0000h
28
DS549PP1
CS4202
4.11
D15
EAPD
Powerdown Control/Status Register (Index 26h)
D14
PR6
D13
PR5
D12
PR4
D11
PR3
D10
PR2
D9
PR1
D8
PR0
D7
0
D6
0
D5
0
D4
0
D3
REF
D2
ANL
D1
DAC
D0
ADC
EAPD
External Amplifier Power Down. The EAPD pin follows this bit and is generally used to power
down external amplifiers. The EAPD bit is mutually exclusive with the SDSC bit in the Serial
Port Control Register (Index 6Ah). The SDSC bit must be ‘clear’ before the EAPD bit may be
‘set’. If the SDSC bit is ‘set’, EAPD is a read-only bit and always returns ‘0’.
PR6
Headphone Amplifier Powerdown. When ‘set’, the headphone amplifier is powered down.
PR5
Internal Clock Disable. When ‘set’, the internal master clock is disabled (BIT_CLK running).
The only way to recover from setting this bit is through a Cold Reset (driving the RESET# signal active).
PR4
AC-link Powerdown. When ‘set’, the AC-link is powered down (BIT_CLK off). The AC-link can
be restarted through a Warm Reset using the SYNC signal, or a Cold Reset using the RESET# signal (primary audio codec only).
PR3
Analog Mixer Powerdown (Vref off). When ‘set’, the analog mixer and voltage reference are
powered down. When clearing this bit, the ANL, ADC, and DAC bits should be checked before writing any mixer registers.
PR2
Analog Mixer Powerdown (Vref on). When ‘set’, the analog mixer is powered down (the voltage reference is still active). When clearing this bit, the ANL bit should be checked before writing any mixer registers.
PR1
Front DACs Powerdown. When ‘set’, the DACs are powered down. When clearing this bit, the
DAC bit should be checked before sending any data to the DACs.
PR0
L/R ADCs and Input Mux Powerdown. When ‘set’, the ADCs and the ADC input muxes are
powered down. When clearing this bit, no valid data will be sent down the AC-link until the
ADC bit goes high.
REF
Voltage Reference Ready Status. When ‘set’, the REF bit indicates the voltage reference is
at a nominal level.
ANL
Analog Ready Status. When ‘set’, the analog output mixer, input multiplexer, and volume controls are ready. When ‘clear’, no volume control registers should be written.
DAC
Front DAC Ready Status. When ‘set’, the DACs are ready to receive data across the AC-link.
When ‘clear’, the DACs will not accept any valid data.
ADC
L/R ADCs Ready Status. When ‘set’, the ADCs are ready to send data across the AC-link.
When ‘clear’, no data will be sent to the controller.
Default
000Fh. This value indicates all blocks are powered on. The lower four bits will change as the
CS4202 finishes an initialization and calibration sequence.
The PR[6:0] and the EAPD bits are powerdown control for different sections of the CS4202 as well as external amplifiers. The REF, ANL, DAC, and ADC bits are read-only status bits which, when ‘set’, indicate that a particular section of the CS4202 is ready. After the controller receives the Codec Ready bit in input Slot 0, these status bits must
be checked before writing to any mixer registers. See Section 8, Power Management, for more information on the
powerdown functions.
DS549PP1
29
CS4202
4.12
D15
ID1
Extended Audio ID Register (Index 28h)
D14
ID0
D13
0
D12
0
D11
D10
D9
REV1 REV0 AMAP
D8
0
D7
0
D6
0
D5
D4
DSA1 DSA0
D3
0
D2
SPDIF
D1
0
D0
VRA
ID[1:0]
Codec ID. These bits indicate the current codec configuration. When ID[1:0] = 00, the
CS4202 is the primary audio codec. When ID[1:0] = 01, 10, or 11, the CS4202 is a secondary
audio codec. The state of the ID[1:0] bits is determined at power-up from the ID[1:0]# pins
and the current clocking scheme, see Table 18 on page 49.
REV[1:0]
AC ’97 Revision. The REV[1:0] bits indicate which version of the AC ’97 specification the codec complies with. These bits always return ‘01’, indicating the CS4202 complies with
version 2.2 of the AC ’97 specification.
AMAP
Audio Slot Mapping. The AMAP bit indicates whether the AC ’97 2.2 compliant AC-link slot to
audio DAC mapping is supported. This bit always returns ‘1’, indicating that audio slot mapping is supported. The PCM playback and capture slots are mapped according to Table 8 on
page 30.
Slot Assignment
DSA1
DSA0
SPSA1 SPSA0
ASA1
ASA0
0
0
1
1
0
1
0
1
DAC
SDOUT
Slot Mapping
SDO2
S/PDIF
ADC
L
3
7
6
10
R
4
8
9
11
L
7
6
10
-
R
8
9
11
-
L
6
10
-
R
9
11
-
L
3
7
6
10
R
4
8
9
11
L
3
7
6
-
R
4
8
11
-
Table 8. Slot Mapping for the CS4202
DSA[1:0]
DAC Slot Assignment. The DSA[1:0] bits control the mapping of output slots to the DAC/SRC
block as well as the serial data port. To satisfy AC ‘97 2.2 AMAP requirements, the default for
these bits will depend on the Codec ID as shown in Table 9. See Table 8 for all available Slot
Map settings.
Codec ID
0
1
2
3
DSA[1:0]
default
00
01
01
10
SPSA[1:0]
default
01
10
10
11
ASA[1:0]
default
00
00
00
00
Table 9. Slot Assignment Defaults
SPDIF
Sony/Philips Digital Interface. The SPDIF bit is ‘set’, indicating that the optional S/PDIF transmitter is supported.
VRA
Variable Rate PCM Audio. The VRA bit indicates whether variable rate PCM audio is supported. This bit always returns ‘1’, indicating that variable rate PCM audio is available.
Default
x605h. The Extended Audio ID Register (Index 28h) is a read-only register, except for the
DSA[1:0] bits which are read/write.
30
DS549PP1
CS4202
4.13
D15
0
Extended Audio Status/Control Register (Index 2Ah)
D14
0
D13
0
D12
0
D11
0
D10
SPCV
D9
0
D8
0
D7
0
D6
0
D5
D4
SPSA1 SPSA0
D3
0
D2
SPDIF
D1
0
D0
VRA
SPCV
S/PDIF Configuration Valid. This read-only bit indicates the status of the S/PDIF transmitter
subsystem, enabling the driver to determine if the currently programmed S/PDIF configuration is supported. SPCV is always valid, independent of the S/PDIF enable bit status.
SPSA[1:0]
S/PDIF Slot Assignment. These bits control the mapping of output slots to the S/PDIF transmitter. To satisfy AC ‘97 2.2 AMAP requirements, the default for these bits will depend on the
Codec ID as shown in Table 9 on page 30. See Table 8 on page 30 for all available Slot Map
settings.
SPDIF
Enable Sony/Philips Digital Interface. This bit enables S/PDIF data transmission on the
SPDIF_OUT pin. The SPDIF bit routes the left and right channel data from the AC ’97 controller or from the ADC output to the S/PDIF transmitter block. The actual data routed to the
S/PDIF block are controlled through the configuration of the SPSA[1:0] bits and the ASPM bit
in the AC Mode Control Register (Index 5Eh).
VRA
Enable Variable Rate Audio. When ‘set’, the VRA bit allows access to the PCM Front DAC
Rate Register (Index 2Ch) and the PCM L/R ADC Rate Register (Index 32h). This bit must
be ‘set’ in order to use variable PCM playback or capture rates. The VRA bit also serves as
a powerdown for the DAC and ADC SRC blocks. Clearing VRA will reset the PCM Front DAC
Rate Register (Index 2Ch) and the PCM L/R ADC Rate Register (Index 32h) to their default
values. The SRC data path is flushed and the Slot Request bits for the currently active DAC
slots will be fixed at ‘0’.
Default
0410h
DS549PP1
31
CS4202
4.14
D15
SR15
Audio Sample Rate Control Registers (Index 2Ch - 32h)
D14
SR14
D13
SR13
D12
SR12
D11
SR11
D10
SR10
D9
SR9
D8
SR8
D7
SR7
D6
SR6
D5
SR5
D4
SR4
D3
SR3
D2
SR2
D1
SR1
D0
SR0
SR[15:0]
Sample Rate Select. The Audio Sample Rate Control Registers (Index 2Ch - 32h) control
playback and capture sample rates. The PCM Front DAC Rate Register (Index 2Ch) controls
the Front Left and Front Right DAC sample rates. The PCM L/R ADC Rate Register
(Index 32h) controls the Left and Right ADC sample rates. There are seven sample rates directly supported by this register, shown in Table 10. Any value written to this register not contained in Table 10 is not directly supported and will be decoded according to the ranges
indicated in the table. The range boundaries have been chosen so that only bits SR[15:12] of
each register will have to be considered. All register read transactions will reflect the actual
value stored (column 2 in Table 10) and not the one attempted to be written.
Default
BB80h. This value corresponds to 48 kHz sample rate.
Writes to the PCM Front DAC Rate Register (Index 2Ch) and the PCM L/R ADC Rate Register (Index 32h) are only
available in Variable Rate PCM Audio mode when the VRA bit in the Extended Audio Status/Control Register
(Index 2Ah) is ‘set’. If VRA = 0, writes to the register are ignored and the register will always read BB80h.
Sample Rate
(Hz)
SR[15:0], register
content (hex value)
SR[15:0], decode
range (hex value)
SR[15:12], decode
range (bin value)
8,000
1F40
0000 - 1FFF
0000 - 0001
11,025
2B11
2000 - 2FFF
0010 - 0010
16,000
3E80
3000 - 3FFF
0011 - 0011
22,050
5622
4000 - 5FFF
0100 - 0101
32,000
7D00
6000 - 7FFF
0110 - 0111
44,100
AC44
8000 - AFFF
1000 - 1010
48,000
BB80
B000 - FFFF
1011 - 1111
Table 10. Directly Supported SRC Sample Rates for the CS4202
32
DS549PP1
CS4202
4.15
D15
V
S/PDIF Control Register (Index 3Ah)
D14
D13
D12
D11
DRS SPSR1 SPSR0
L
D10
CC6
D9
CC5
D8
CC4
D7
CC3
D6
CC2
D5
CC1
D4
CC0
D3
PRE
D2
D1
D0
COPY /AUDIO PRO
V
Validity. The V bit is mapped to the V bit (bit 28) of every sub-frame. If this bit is ‘clear’, the
signal is suitable for conversion or processing.
DRS
Double Rate S/PDIF. The DRS bit is mapped to bit 27 of the channel status block. This bit
controls support for optional higher sample rate transmission. The CS4202 does not support
double rate S/PDIF transmission, therefore DRS is a read-only bit and always returns ‘0’.
SPSR[1:0]
S/PDIF Sample Rate. The SPSR[1:0] bits are mapped to bits 24 and 25 of the channel status
block. These bits control the S/PDIF transmitter clock rate. The CS4202 only supports transmission at the standard 48 kHz rate, therefore SPSR[1:0] are read-only bits and always
return ‘10’.
L
Generation Status. The L bit is mapped to bit 15 of the channel status block. For category
codes 001xxxx, 0111xxx and 100xxxx, a value of ‘0’ indicates original material and a value of
‘1’ indicates a copy of original material. For all other category codes the definition of the L bit
is reversed.
CC[6:0]
Category Code. The CC[6:0] bits are mapped to bits 8-14 of the channel status block.
PRE
Data Pre-emphasis. The PRE bit is mapped to bit 3 of the channel status block. If the PRE bit
is ‘set’, 50/15 µs filter pre-emphasis is indicated. If the bit is ‘clear’, no pre-emphasis is indicated.
COPY
Copyright. The COPY bit is mapped to bit 2 of the channel status block. If the COPY bit is ‘set’
copyright is not asserted and copying is permitted.
/AUDIO
Audio / Non-Audio. The /AUDIO bit is mapped to bit 1 of the channel status block. If the
/AUDIO bit is ‘clear’, the data transmitted over S/PDIF is assumed to be digital audio. If the
/AUDIO bit is ‘set’, non-audio data is assumed.
PRO
Professional/Consumer. The PRO bit is mapped to bit 0 of the channel status block. If the
PRO bit is ‘clear’, consumer use of the audio control block is indicated. If the bit is ‘set’, professional use is indicated.
Default
2000h
For a further discussion of the proper use of the channel status bits see application note AN22: Overview of Digital
Audio Interface Data Structures [3]
DS549PP1
33
CS4202
4.16
D15
ID1
Extended Modem ID Register (Index 3Ch)
D14
ID0
D13
0
D12
0
D11
0
D10
0
D9
0
D8
0
D7
0
D6
0
D5
0
D4
0
D3
0
D2
0
D1
0
D0
0
ID[1:0]
Codec ID. These bits indicate the current codec configuration. When ID[1:0] = 00, the
CS4202 is the primary audio codec. When ID[1:0] = 01, 10, or 11, the CS4202 is a secondary
audio codec. The state of the ID[1:0] bits is determined at power-up from the ID[1:0]# pins
and the current clocking scheme, see Table 18 on page 49.
Default
x000h. This value indicates no supported modem functions.
The Extended Modem ID Register (Index 3Ch) is a read/write register that identifies the CS4202 modem capabilities.
Writing any value to this location issues a reset to modem registers (Index 3Ch-54h), including GPIO registers
(Index 4Ch - 54h). Audio registers are not reset by a write to this location.
4.17
D15
0
Extended Modem Status/Control Register (Index 3Eh)
D14
0
D13
0
D12
0
D11
0
D10
0
D9
0
D8
PRA
D7
0
D6
0
D5
0
D4
0
D3
0
D2
0
D1
0
D0
GPIO
PRA
GPIO Powerdown. When ‘set’, the PRA bit powers down the GPIO subsystem. When the
GPIO section is powered down, all outputs must be tri-stated and input Slot 12 should be
marked invalid when the AC-link is active. To use any GPIO functionality PRA must be
cleared first.
GPIO
GPIO. When ‘set’, the GPIO bit indicates the GPIO subsystem is ready for use. When ‘set’,
input Slot 12 will also be marked valid.
Default
0100h
4.18
D15
0
GPIO Pin Configuration Register (Index 4Ch)
D14
0
D13
0
D12
0
D11
0
D10
0
D9
0
D8
0
D7
0
D6
0
D5
0
D4
GC4
D3
GC3
D2
GC2
D1
GC1
D0
GC0
GC[4:0]
GPIO Pin Configuration. When ‘set’, the GC[4:0] bits define the corresponding GPIO pin as
an input. When ‘clear’, the corresponding GPIO pin is defined as an output. When the SDEN
bit in the Serial Port Control Register (Index 6Ah) is ‘set’, the GC[1:0] bits are read-only bits
and always return ‘0’. When SDEN is ‘clear’, the GC[1:0] bits function normally. Likewise,
when the SDO2 bit in the Serial Port Control Register (Index 6Ah) is 'set', the GC4 bit is a
read-only bit and always returns '0'. When SDO2 is 'clear', the GC4 bit functions normally.
The GC[3:2] bits have no such dependency.
Default
001Fh. This value corresponds to all GPIO pins configured as inputs.
After a Cold Reset or a modem Register Reset (see Extended Modem ID Register (Index 3Ch)), all GPIO pins are
configured as inputs. The upper 11 bits of this register always return ‘0’.
34
DS549PP1
CS4202
4.19
D15
1
GPIO Pin Polarity/Type Configuration Register (Index 4Eh)
D14
1
D13
1
D12
1
D11
1
D10
1
D9
1
D8
1
D7
1
D6
1
D5
1
D4
GP4
D3
GP3
D2
GP2
D1
GP1
D0
GP0
GP[4:0]
GPIO Pin Configuration. This register defines the GPIO input polarity (0 = Active Low,
1 = Active High) when a GPIO pin is configured as an input. The GP[4:0] bits define the GPIO
output type (0 = CMOS, 1 = OPEN-DRAIN) when a GPIO pin is configured as an output. The
GC[4:0] bits in the GPIO Pin Configuration Register (Index 4Ch) define the GPIO pins as inputs or outputs. See Table 11 for the various GPIO configurations.
Default
FFFFh
After a Cold Reset or a modem Register Reset this register defaults to all 1’s. The upper 11 bits of this register always return ‘1’.
GCx GPx Function
Configuration
0
0
Output
CMOS Drive
0
1
Output
Open Drain
1
0
Input
Active Low
1
1
Input
Active High (default)
Table 11. GPIO Input/Output Configurations
4.20
D15
0
GPIO Pin Sticky Register (Index 50h)
D14
0
D13
0
D12
0
D11
0
D10
0
D9
0
D8
0
D7
0
D6
0
D5
0
D4
GS4
D3
GS3
D2
GS2
D1
GS1
D0
GS0
GS[4:0]
GPIO Pin Sticky. This register defines the GPIO input type (0 = not sticky, 1 = sticky) when a
GPIO pin is configured as an input. The GPIO pin status of an input configured as “sticky” is
‘cleared’ by writing a ‘0’ to the corresponding bit of the GPIO Pin Status Register (Index 54h),
and by reset.
Default
0000h
After a Cold Reset or a modem Register Reset this register defaults to all 0’s, specifying “non-sticky”. “Sticky” is defined as edge sensitive, “non-sticky” as level sensitive. The upper 11 bits of this register always return ‘0’.
DS549PP1
35
CS4202
4.21
GPIO Pin Wakeup Mask Register (Index 52h)
D15
0
D14
0
D13
0
D12
0
D11
0
D10
0
D9
0
D8
0
D7
0
D6
0
D5
0
D4
GW4
D3
GW3
D2
GW2
D1
GW1
D0
GW0
GW[4:0]
GPIO Pin Wakeup. This register provides a mask for determining if an input GPIO change will
generate a wakeup event (0 = no, 1 = yes). When the AC-link is powered up, a wakeup event
will be communicated through the assertion of GPIO_INT = 1 in input Slot 12. When the
AC-link is powered down (Powerdown Control/Status Register (Index 26h) bit PR4 = 1 for primary codecs), a wakeup event will be communicated through a ‘0’ to ‘1’ transition on
SDATA_IN.
Default
0000h
GPIO bits which have been programmed as inputs, “sticky”, and “wakeup”, upon transition either (high-to-low) or
(low-to-high) depending on pin polarity, will cause an AC-link wakeup if and only if the AC-link was powered down.
Once the controller has re-established communication with the CS4202 following a Warm Reset, it will continue to
signal the wakeup event through the GPIO_INT bit of input Slot 12 until the AC ’97 controller clears the interrupt-causing bit in the GPIO Pin Status Register (Index 54h); or the “wakeup”, config, or “sticky” status of that GPIO
pin changes.
After a Cold Reset or a modem Register Reset (see Extended Modem ID Register (Index 3Ch)) this register defaults
to all 0’s, specifying no wakeup event. The upper 11 bits of this register always return ‘0’.
4.22
D15
0
GPIO Pin Status Register (Index 54h)
D14
0
D13
0
D12
0
D11
0
D10
0
D9
0
D8
0
D7
0
D6
0
D5
0
D4
GI4
D3
GI3
D2
GI2
D1
GI1
D0
GI0
GI[4:0]
GPIO Pin Status. This register reflects the state of all GPIO pin inputs and outputs. These
values are also reflected in Slot 12 of every SDATA_IN frame. GPIO inputs configured as
“sticky” are ‘cleared’ by writing a ‘0’ to the corresponding bit of this register. The GPIO_INT
bit in input Slot 12 is ‘cleared’ by clearing all interrupt-causing bits in this register.
Default
0000h
GPIO pins which have been programmed as inputs and “sticky”, upon transition either (high-to-low) or (low-to-high)
depending on pin polarity, will cause the individual GI bit to be ‘set’, and remain ‘set’ until ‘cleared’. GPIO pins which
have been programmed as outputs are controlled either through output Slot 12 or through this register, depending
on the state of the GPOC bit in the Misc. Crystal Control Register (Index 60h). If the GPOC bit is ‘cleared’, the GI
bits in this register are read-only and reflect the status of the corresponding GPIO output pin ‘set’ through output
slot 12. If the GPOC bit is ‘set’, the GI bits in this register are read/write bits and control the corresponding GPIO
output pins.
The default value is always the state of the GPIO pin. The upper 11 bits of this register should be forced to zero in
this register and input Slot 12.
4.23
D15
0
ASPM
36
AC Mode Control Register (Index 5Eh)
D14
0
D13
0
D12
0
D11
ASPM
D10
0
D9
TMM
D8
DDM
D7
0
D6
0
D5
D4
ASA1 ASA0
D3
0
D2
0
D1
0
D0
0
Analog S/PDIF Mode. The ASPM bit controls the input source to the S/PDIF transmitter block.
When ‘clear’, the S/PDIF transmitter will receive data from the corresponding AC-link output
slots. The actual slots are determined by the state of the SPSA[1:0] bits in the Extended Audio
Status/Control Register (Index 2Ah). If ‘set’, the S/PDIF transmitter block will receive data
DS549PP1
CS4202
from the ADC output.
TMM
True Mono Mode. The TMM bit controls the source of the stereo-to-mono mixer that feeds
into the mono out select mux. If this bit is ‘clear’, the output of the stereo input mixer is sent
to the stereo-to-mono mixer. If this bit is ‘set’, the output of the DAC direct mode mux is sent
to the stereo-to-mono mixer. This allows a true mono mix that includes the PC Beep and
Phone inputs and also works during DAC direct mode.
DDM
DAC Direct Mode. The DDM bit controls the source of the line and headphone output drivers.
When this bit is ‘clear’, the CS4202 stereo output mixer drives the line and headphone outputs. When this bit is ‘set’, the CS4202 audio DACs (DAC1 and DAC2) directly drive the line
and headphone outputs.
ASA[1:0]
ADC Slot Assignment. The ASA[1:0] bits control the mapping of input slots to the ADC/SRC
block. The default value of ‘00’ selects input slots 3 and 4. See Table 8 on page 30 for all
available Slot Map settings.
Default
0000h
DS549PP1
37
CS4202
4.24
D15
0
Misc. Crystal Control Register (Index 60h)
D14
0
D13
0
D12
DPC
D11
0
D10
0
D9
D8
Reserved
D7
10dB
D6
CRST
D5
0
D4
0
D3
GPOC
D2
D1
Reserved
D0
LOSM
DPC
DAC Phase Control. This bit controls the phase of the PCM stream sent to the DACs (after
SRC). When ‘cleared’ the phase of the signal will remain unchanged. When this bit is ‘set’,
each PCM sample will be inverted before being sent to the DACs.
10dB
Microphone 10 dB Boost. When ‘set’, the 10dB bit enables an additional boost of 10 dB on
the selected microphone input. In combination with the 20dB boost bit in the Microphone Volume Register (Index 0Eh) this bit allows for variable boost from 0 dB to +30 dB in steps of
10 dB.
CRST
Force Cold Reset. The CRST bit is used as an override to the New Warm Reset behavior
defined during PR4 powerdown. If this bit is ‘set’, an active RESET# signal will force a Cold
Reset to the CS4202 during a PR4 powerdown.
GPOC
General Purpose Output Control. The GPOC bit specifies the mechanism by which the status
of a General Purpose Output pin can be controlled. If this bit is ‘cleared’, the GPO status is
controlled through the standard AC ’97 method of setting the appropriate bits in output
Slot 12. If this bit is ‘set’, the GPO status is controlled through the GPIO Pin Status Register
(Index 54h).
LOSM
Loss of SYNC Mute Enable. The LOSM bit controls the loss of SYNC mute function. If this bit
is ‘set’, the CS4202 will mute all analog outputs for the duration of loss of SYNC. If this bit is
‘cleared’, the mixer will continue to function normally during loss of SYNC. The CS4202 expects to sample SYNC ‘high’ for 16 consecutive BIT_CLK periods and then ‘low’ for 240 consecutive BIT_CLK periods, otherwise loss of SYNC becomes true.
Default
0003h
38
DS549PP1
CS4202
4.25
D15
SDEN
Serial Port Control Register (Index 6Ah)
D14
0
D13
0
D12
0
D11
0
D10
0
D9
0
D8
0
D7
0
D6
0
D5
0
D4
0
D3
D2
D1
D0
SDO2 SDSC SDF1 SDF0
SDEN
Serial Data Output Enable. The SDEN bit enables transmission of serial data on the SDOUT
pin. The SDEN bit routes the left and right channel data from the AC ’97 controller to the serial
data port. The actual data routed to the serial data port are controlled through the DSA[1:0]
configuration in the Extended Audio ID Register (Index 28h). SDEN also functions as a master control for the second serial data output port and the serial clock. Setting this bit also disables the GPIO[1:0] pins and clears the GC[1:0] bits in the GPIO Pin Configuration Register
(Index 4Ch). Clearing this bit re-enables the GPIO[1:0] pins and sets the GC[1:0] bits.
SDO2
Serial Data Output 2 Enable. The SDO2 bit enables transmission of serial data on the
GPIO4/SDO2 pin. The SDO2 bit routes the left and right channel data from the AC ’97 controller to the second serial data port. The actual slots routed to the second serial data port are
controlled through the DSA[1:0] configuration in the Extended Audio ID Register (Index 28h).
This bit can only be ‘set’ if the SDEN bit is ‘1’ and will be ‘cleared’ automatically if SDEN returns to ‘0’. Setting this bit also disables the GPIO4 pin and clears the GC4 bit in the GPIO
Pin Configuration Register (Index 4Ch). Clearing this bit re-enables the GPIO4 pin and sets
the GC4 bit.
SDSC
Serial Clock Enable. The SDSC bit enables transmission of a serial clock on the EAPD/SCLK
pin. Serial data can be routed to DACs that support internal SCLK mode without transmitting
a serial clock. For DACs that only support external SCLK mode, transmission of a serial clock
is required and this bit must be set to ‘1’. This bit can only be set if the SDEN bit is ‘1’ and will
be cleared automatically if SDEN returns to ‘0’. Furthermore, the SDSC bit can only be ‘set’
if the EAPD bit in the Powerdown Control/Status Register (Index 26h) is ‘0’. If the SDEN bit
is ‘0’ or the EAPD bit is ‘1’, SDSC is a read-only bit and always returns ‘0’.
SDF[1:0]
Serial Data Format. The SDF[1:0] bits control the format of the serial data transmitted on the
two output ports. All ports will use the same format. See Table 12 for available formats.
Default
0000h
SDF1 SDF0
Serial Data Format
0
0
I2S
0
1
Left Justified
1
0
Right Justified, 20-bit data
1
1
Right Justified, 16-bit data
Table 12. Serial Data Format Selection
DS549PP1
39
CS4202
4.26
D15
E15
BIOS-Driver Interface Control Registers (Index 70h - 72h)
D14
E14
D13
E13
D12
E12
D11
E11
D10
E10
D9
E9
D8
E8
D7
E7
D6
E6
D5
E5
D4
E4
D3
E3
D2
E2
D1
E1
E[15:0]
Event Configuration. The E[15:0] bits control the BIOS-Driver Interface mechanism.
Default
0000h
D0
E0
The BDI Config Register (Index 70h) enables BIOS-Driver communication for each possible event. If a bit is ‘0’, the
corresponding event will not be communicated. If a bit is ‘1’, the corresponding event will be communicated by asserting the BDI bit in input slot 12. If an event occurs, the BIOS will ‘set’ the corresponding bit in the BDI Status Register (Index 7Ah). This bit remains ‘set’ until it is cleared by the driver, acknowledging the event has been handled.
This behavior is equivalent to “non-sticky” (level sensitive) GPIO input pins.
The BDI Wakeup Register (Index 72h) provides a mask for determining if a BDI event will generate a wakeup or
GPIO_INT. If a bit is ‘0’, the corresponding event will not generate an interrupt. If a bit is ‘1’, the corresponding event
will generate an interrupt. Refer to the GPIO Pin Wakeup Mask Register (Index 52h) for details about wakeup interrupts.
4.27
D15
E15
BIOS-Driver Interface Status Register (Index 7Ah)
D14
E14
D13
E13
D12
E12
D11
E11
D10
E10
D9
E9
D8
E8
D7
E7
D6
E6
D5
E5
D4
E4
D3
E3
D2
E2
D1
E1
D0
E0
E[15:0]
Event Status. This register, in conjunction with the BIOS-Driver Interface Control Registers
(Index 70h - 72h), controls the BIOS-Driver Interface mechanism.
Default
0000h
The BDI Status Register (Index 7Ah) reflects the state of all possible events. If a bit is ‘0’, the corresponding event
has not occurred or has already been handled by the driver. If a bit is ‘1’, the corresponding event has occurred and
has not been handled by the driver yet. The BDI bit in input slot 12 is a logic OR of all bits in this register ANDed
with their corresponding bit in the BDI Config Register (Index 70h). After handling an event, the driver should clear
it by writing a ‘0’ to the corresponding bit of this register.
40
DS549PP1
CS4202
4.28
Vendor ID1 Register (Index 7Ch)
D15
F7
D14
F6
D13
F5
D12
F4
D11
F3
D10
F2
D9
F1
D8
F0
D7
S7
D6
S6
D5
S5
D4
S4
D3
S3
D2
S2
D1
S1
D0
S0
F[7:0]
First Character of Vendor ID. With a value of F[7:0] = 43h, these bits define the ASCII ‘C’ character.
S[7:0]
Second Character of Vendor ID. With a value of S[7:0] = 52h, these bits define the ASCII ‘R’
character.
Default
4352h. This register contains read-only data.
4.29
Vendor ID2 Register (Index 7Eh)
D15
T7
D14
T6
D13
T5
D12
T4
D11
T3
D10
T2
D9
T1
D8
T0
D7
0
D6
DID2
D5
DID1
D4
DID0
D3
0
D2
D1
D0
REV2 REV1 REV0
T[7:0]
Third Character of Vendor ID. With a value of T[7:0] = 59h, these bits define the ASCII ‘Y’
character.
DID[2:0]
Device ID. With a value of DID[2:0] = 111, these bits specify the audio codec is a CS4202.
REV[2:0]
Revision. With a value of REV[2:0] = 001, these bits specify the audio codec revision is ‘A’.
Default
597xh. This register contains read-only data.
The two Vendor ID registers provide a means to determine the manufacturer of the AC ’97 audio codec. The first
three bytes of the Vendor ID registers contain the ASCII code for the first three letters of Crystal (CRY). The final
byte of the Vendor ID registers is divided into a Device ID field and a Revision field. Table 13 lists the currently defined Device ID’s.
DID2 - DID0
Part Name
000
CS4297
001
CS4297A
010
CS4294/CS4298
011
CS4299
100
CS4201
101
CS4205
110
CS4291
111
CS4202
Table 13. Device ID with Corresponding Part Number
DS549PP1
41
CS4202
the DPC bit in the Misc. Crystal Control Register
(Index 60h). This feature is necessary since the
phase response for external DACs is unknown and
the phase response of the internal DACs can vary
depending on the path determined by the DDM bit
in the AC Mode Control Register (Index 5Eh) and
the output (LINE_OUT or HP_OUT) being used.
This feature guarantees that all DACs in a system
have the same phase response, maintaining the accuracy of spatial cues.
5. SERIAL DATA PORTS
5.1
Overview
The CS4202 implements two serial data output
ports that can be used for multi-channel expansion.
Each serial port consists of 4 signals: MCLK,
SCLK, LRCLK, and SDATA. The existing 256 Fs
BIT_CLK will be used as MCLK. The clock pins
are shared between all the serial ports with only the
SDATA pins being separate; SDOUT for the first
output port, and SDO2 for the second output port.
Serial data is transmitted on these ports every
AC-link frame.
Please note the data sent to the serial ports is
straight from the AC-link. There is no SRC and no
volume control available on this data, so it is the responsibility of the controller or host software to
provide this functionality if desired.
The serial data port is controlled by the SDEN,
SDSC, and SDO2 bits in the Serial Port Control
Register (Index 6Ah). All the serial data port pins
are multiplexed with other functions and cannot be
used unless the other function is disabled or powered down; see Section 7, Exclusive Functions.
Some audio DACs can run in an internal SCLK
mode where SCLK is internally derived from
MCLK and LRCLK. In this case, SCLK generation
in the CS4202 is optional.
5.2
For multi-channel expansion, the two serial data
output ports are used to send AC-link data to one or
two external stereo DACs to support up to a total of
six channels. The first serial port takes the digital
audio data from the SDOUT slots. The second serial port takes the digital audio data from the SDO2
slots. See Table 8 on page 30 for the actual slots
used depending on configuration. Figure 10 shows
a six channel application using the CS4202.
A feature has been designed into the CS4202 that
allows the phase of the internal DACs to be reversed. This DAC phase reversal is controlled by
LINE_OUT_L
LINE_OUT_R
Multi-Channel Expansion
35
+
10uF
ELEC
Left Front
36
+
10uF
ELEC
Right Front
220K
220K
1000pF 1000pF
AGND
GPIO1/SDOUT
EAPD/SCLK
GPIO0/LRCLK
BIT_CLK
GPIO4/SDO2
44
47
43
6
34
CS4334
1
8
SDATA
AOUTL
2
DEM#/SCLK
3
LRCK
4
5
MCLK
AOUTR
+
270K
CS4334
8
1
SDATA
AOUTL
2
DEM#/SCLK
3
LRCK
4
5
MCLK
AOUTR
AGND
+
10uF
ELEC
47K
AGND
2700pF 2700pF
AGND
+
10uF
ELEC
560
Center
+
10uF
ELEC
560
LFE
270K
AGND
Right Surround
47K
AGND
270K
560
10uF
ELEC
270K
Left Surround
560
47K
47K
AGND
2700pF 2700pF
AGND
Figure 10. Serial Data Port: Six Channel Circuit
42
DS549PP1
CS4202
5.3
be 64 Fs (BIT_CLK/4). Serial data is transitioned by
the CS4202 on the falling edge of SCLK and latched
by the DACs on the next rising edge. Serial data is
shifted out MSB first in all supported formats, but
LRCLK polarity as well as data justification, alignment, and resolution vary. Table 14 shows the principal characteristics of each serial format.
Serial Data Formats
In order to support a wide variety of serial audio
DACs, the CS4202 can transmit serial data in four
different formats. The desired format is selected
through the SDF[1:0] bits in the Serial Port Control
Register (Index 6Ah). All serial ports use the same
serial data format when enabled. In all cases, LRCLK will be synchronous with Fs, and SCLK will
SDF[1:0]
00
01
10
11
LRCLK
Data
Data Alignment
Data
Timing
Polarity Justification (MSB vs. LRCLK) Resolution Diagram
negative
positive
positive
positive
left justified
left justified
right justified
right justified
1 SCLK delayed
not delayed
not delayed
not delayed
20-bit
20-bit
20-bit
16-bit
Recommended
DAC
Figure 11
Figure 12
Figure 13
Figure 14
CS4334
CS4335
CS4337
CS4338
Table 14. Serial Data Formats and Compatible DACs for the CS4202
L eft C ha n ne l
LR CK
R ig h t C h a n ne l
S CLK
SDATA
MSB -1 -2 -3 -4 -5
+5 +4 +3 +2 +1 LSB
MSB -1 -2 -3 -4
+5 +4 +3 +2 +1 LSB
Figure 11. Serial Data Format 0 (I2S)
L eft C ha n ne l
LR CK
R ig h t C h a n ne l
S CLK
SDATA
MSB-1 -2 -3 -4 -5
+5 +4 +3 +2 +1 LSB
MSB -1 -2 -3 -4
+5 +4 +3 +2 +1 LSB
Figure 12. Serial Data Format 1 (Left Justified)
LRCK
R ight C ha nne l
Le ft C h ann el
SCLK
SDA TA
1 0
19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
Figure 13. Serial Data Format 2 (Right Justified, 20-bit data)
LR C K
R ig h t C h a n n e l
L e ft C ha n n e l
SC LK
S D A TA
15 14 13 12 11 10 9
8
7
6
5
4
3
2
1
0
15 14 13 12 11 10 9
8
7
6
5
4
3
2
1
0
Figure 14. Serial Data Format 3 (Right Justified, 16-bit data)
DS549PP1
43
CS4202
6. SONY/PHILIPS DIGITAL
INTERFACE (S/PDIF)
with SDOUT pin, and GPIO4 pin is shared with
SDO2 pin)
The S/PDIF digital output is used to interface the
CS4202 to consumer audio equipment external to
the PC. This output provides an interface for storing digital audio data or playing digital audio data
to digital speakers. Figure 15 illustrates the circuits
necessary for implementing the IEC-958 optical or
consumer interface. For further information on
S/PDIF operation see application note AN22: Overview of Digital Audio Interface Data Structures [3].
For further information on S/PDIF recommended
transformers see application note AN134: AES and
S/PDIF Recommended Transformers [4].
7. EXCLUSIVE FUNCTIONS
Some of the digital pins on the CS4202 have multiplexed functionality. These functions are mutually exclusive and cannot be requested at the same
time. The following pairs of functions are mutually
exclusive:
•
GPIO and Serial Data Port (GPIO0 pin is
shared with LRCLK pin, GPIO1 pin is shared
•
EAPD and Serial Data Port Serial Clock
(EAPD pin is shared with SCLK pin)
Use of the GPIO0/LRCLK, GPIO1/SDOUT, and
GPIO4/SDO2 pins for serial data port has priority
over their GPIO functionality. There is no priority
assigned to the other exclusive function. A function
currently in use must be disabled or powered down
before the corresponding exclusive function can be
enabled. The following control bits for these functions will behave differently than normal bits: the
EAPD bit in the Powerdown Control/Status Register (Index 26h), the GC[4,1:0] bits in the GPIO Pin
Configuration Register (Index 4Ch), and the
SDO2, and SDSC bits in the Serial Port Control
Register (Index 6Ah). These bits can become
read-only bits if they control a feature that is currently unavailable because the corresponding exclusive feature is already in use, or the
corresponding master control for this feature is not
set.
5
J1
R1
+5V_PCI
SPDIF_OUT
R2
T1
0.1 µ F
SPDIF_OUT 4
3
8.2 kΩ 2
1
DVdd 3.3V
5V
R1 247.5 Ω 375 Ω
R2 107.6 Ω 93.75 Ω
DGND
DGND
DGND
6
TOTX-173
DGND
Figure 15. S/PDIF Output
44
DS549PP1
CS4202
8. POWER MANAGEMENT
8.1
AC ’97 Reset Modes
The CS4202 supports four reset methods, as defined in the AC ’97 Specification: Cold Reset,
Warm Reset, New Warm Reset, and Register Reset.
A Cold Reset results in all AC ’97 logic (registers
included) initialized to its default state. A Warm
Reset or New Warm Reset leaves the contents of
the AC ’97 register set unaltered. A Register Reset
initializes only the AC ’97 registers to their default
states.
8.1.1
Cold Reset
A Cold Reset is achieved by asserting RESET# for
a minimum of 1 µs after the power supply rails
have stabilized. This is done in accordance with the
minimum timing specifications in the AC ’97 Serial Port Timing section on page 9. Once de-asserted,
all of the CS4202 registers will be reset to their default power-on states and the BIT_CLK and
SDATA_IN signals will be reactivated.
8.1.2
Warm Reset
A Warm Reset allows the AC-link to be reactivated
without losing information in the CS4202 registers.
A Warm Reset is required to resume from a D3hot
state where the AC-link had been halted yet full
power had been maintained. A primary codec
Warm Reset is initiated when the SYNC signal is
driven high for at least 1 µs and then driven low in
the absence of the BIT_CLK clock signal. The
BIT_CLK clock will not restart until at least 2 nor-
DS549PP1
mal BIT_CLK clock periods (162.8 ns) after the
SYNC signal is de-asserted. A Warm Reset of the
secondary codec is recognized when the primary
codec on the AC-link resumes BIT_CLK generation. The CS4202 will wait for BIT_CLK to be stable to restore SDATA_IN activity, S/PDIF and/or
serial data port transmission on the following
frame.
8.1.3
New Warm Reset
The New Warm Reset also allows the AC-link to
be reactivated without losing information in the
registers. A New Warm Reset is required to resume
from a D3cold state where AC-link power has been
removed. New Warm Reset is recognized by the
low-high transition of RESET# after the AC-link
has been programmed into PR4 powerdown. The
New Warm Reset functionality can be disabled by
setting the CRST bit in the Misc. Crystal Control
Register (Index 60h).
8.1.4
Register Reset
The last reset mode provides a Register Reset to the
CS4202. This is available only when the CS4202
AC-link is active and the Codec Ready bit is ‘set’.
The audio (including extended audio) control registers (Index 00h - 3Ah) and the vendor specific
registers (Index 5Ah - 7Ah) are reset to their default states by a write of any value to the Reset Register (Index 00h). The modem (including GPIO)
registers (Index 3Ch - 56h) are reset to their default
states by a write of any value to the Extended Modem ID Register (Index 3Ch).
45
CS4202
8.2
Powerdown Controls
The
Powerdown
Control/Status
Register
(Index 26h) controls the power management functions. The PR[6:0] bits in this register control the
internal powerdown states of the CS4202. Powerdown control is available for individual subsections
of the CS4202 by asserting any PRx bit or any combination of PRx bits. All powerdown states except
PR4 and PR5 can be resumed by clearing the corresponding PRx bit. Table 15 shows the mapping
of the power control bits to the functions they manage.
When PR0 is ‘set’, the L/R ADCs and the Input
Mux are shut down and the ADC bit in the Powerdown Control/Status Register (Index 26h) is
‘cleared’ indicating the ADCs are no longer in a
ready state. The same is true for PR1 and the
DACs, PR2 and the analog mixer, PR3 and the
voltage reference (Vrefout), and PR6 and the headphone amplifier. When one of these bits is
‘cleared’, the corresponding subsystem will begin a
power-on process, and the associated status bit will
be ‘set’ when the hardware is ready.
In a primary codec the PR4 bit powers down the
AC-link, but all other analog and digital sub-
systems continue to function. The required resume
sequence from a PR4 state is either a Warm Reset
or a New Warm Reset, depending on whether a
D3hot or D3cold state has been entered.
The PR5 bit disables all internal clocks and powers
down the DACs and the ADCs, but maintains operation of the BIT_CLK and the analog mixer. A
Cold Reset is the only way to restore operation to
the CS4202 after asserting PR5. To achieve a complete digital powerdown, PR4 and PR5 must be asserted within a single AC output frame. This will
also drive BIT_CLK ‘low’.
The CS4202 does not automatically mute any input
or output when the powerdown bits are ‘set’. The
software driver controlling the AC ’97 device must
manage muting the input and output analog signals
before putting the part into any power management
state. The definition of each PRx bit may affect a
single subsection or a combination of subsections
within the CS4202. Table 16 contains the matrix of
subsections affected by the respective PRx function. Table 17 shows the different operating power
consumptions levels for different powerdown functions.
PR Bit
Function
PR0
L/R ADCs and Input Mux Powerdown
PR1
Front DACs Powerdown
PR2
Analog Mixer Powerdown (Vref on)
PR3
Analog Mixer Powerdown (Vref off)
PR4
AC-link Powerdown (BIT_CLK off)*
PR5
Internal Clock Disable
PR6
Headphone Out Powerdown
* Applies only to primary codec
Table 15. Powerdown PR Bit Functions
46
DS549PP1
CS4202
PR Bit
ADCs
PR0
•
DACs
Mixer
•
•
•
•
•
PR1
•
•
PR2
PR3
Analog
Reference
AC
Link
Internal
Clock Off
Headphone
•
•
•
•
PR4
•
PR5
•
•
•
PR6
Table 16. Powerdown PR Function Matrix for the CS4202
Power State
IDVdd (mA)
[DVdd=3.3 V]
IDVdd (mA)
[DVdd=5 V]
IAVdd1 (mA)
IAVdd2 (mA)
Full Power + SRC’s
25.2
40.2
31.3
5.1
Full Power + S/PDIF 1
30.0
46.6
31.3
5.1
Full Power + HP 2
26.4
41.5
32.1
39.5
Full Power
26.4
41.5
31.3
5.1
ADCs off (PR0)
24.0
37.9
23.2
4.9
DACs off (PR1)
24.3
38.4
25.8
5.0
Audio off (PR2)
21.9
34.9
3.8
0 µA
Vref off (PR3)
21.9
34.9
1.5
0 µA
AC-Link off (PR4)
21.8
35.3
31.2
5.1
Internal Clocks off (PR5)
3.8
6.3
19.0
4.6
HP amp off (PR6)
26.3
41.5
29.8
0 µA
Digital off (PR4+PR5)
10 µA
21 µA
19.0
4.6
All off (PR3+PR4+PR5)
10 µA
21 µA
1.3
0 µA
RESET
0.8
1.4
3.6
0 µA
Table 17. Power Consumption by Powerdown Mode for the CS4202
1
Assuming standard resistive load for transformer coupled coaxial S/PDIF output (Rload = 292 Ohm, DVdd
= 3.3 V) (Rload = 415 Ohm, DVdd = 5 V). General: IDVdd S/PDIF = IDVdd + DVdd/Rload/2
2 HP_OUT_L, HP_OUT_R driving 4 Vpp into 32 Ohm resistive load.
DS549PP1
47
CS4202
9. CLOCKING
9.2
The CS4202 may be operated as a primary or secondary codec. As a primary codec, the system clock
for the AC-link may be generated from an external
24.576 MHz clock source, a 24.576 MHz crystal, or
the internal Phase Locked Loop (PLL). The PLL allows the CS4202 to accept external clock frequencies other than 24.576 MHz. As a secondary codec,
the system clock is derived from BIT_CLK, which is
generated by the primary codec. The CS4202 uses
the presence or absence of a valid clock on the
XTL_IN pin in conjunction with the state of the
ID[1:0]# pins to determine the clocking configuration. See Table 18 for all available CS4202 clocking
modes.
If a valid clock is not present on XTL_IN during the
rising edge of RESET#, the device disables the PLL
input and latches the state of the ID[1:0]# inputs. If
the ID[1:0]# inputs are both pulled high or left floating, the device is configured as a primary codec. An
external 24.576 MHz crystal is used as the system
clock as shown in Figure 17.
9.1
PLL Operation (External Clock)
The PLL mode is activated if a valid clock is present
on XTL_IN before the rising edge of RESET#. Once
PLL mode is entered, the XTL_OUT pin is redefined
as the PLL loop filter, as shown in Figure 16. The
ID[1:0]# inputs determine the configuration of the
internal divider ratios required to generate the
12.288 MHz BIT_CLK output; see Table 18 on
page 49 for additional details. In PLL mode, the
CS4202 is configured as a primary codec independent of the state of the ID[1:0]# pins. If 24.576 MHz
is chosen as the external clock input (ID[1:0]# inputs
both pulled high or left floating), the PLL is disabled
and the clock is used directly. The loop filter is not
required and XTL_OUT is left unconnected. For all
other clock input choices, the loop filter is required.
The ID[1:0] bits of the Extended Audio ID Register
(Index 28h) and the Extended Modem ID Register
(Index 3Ch) will always report ‘00’ in PLL mode.
48
9.3
24.576 MHz Crystal Operation
Secondary Codec Operation
If a valid clock is not present on XTL_IN and either
ID[1:0]# input is pulled low during the rising edge of
RESET#, the device is determined to be a secondary
codec. The BIT_CLK pin is configured as an input
and the CS4202 is driven from the 12.288 MHz
BIT_CLK of the primary codec. The ID[1:0] bits of
the Extended Audio ID Register (Index 28h) and the
Extended Modem ID Register (Index 3Ch) will report the state of the ID[1:0]# inputs.
Clock Source
XTL_IN
XTL_OUT
2.2 kΩ
220 pF
0.022 uF
DGND
Figure 16. PLL External Loop Filter
DS549PP1
CS4202
XTL_IN
XTL_OUT
24.576 MHz
22 pF
22 pF
DGND
Figure 17. External Crystal
External
Clock on ID1# ID0#
XTL_IN
Yes
Yes
Yes
Yes
No
No
No
No
1
1
0
0
1
1
0
0
1
0
1
0
1
0
1
0
AC-Link
Timing
Mode
Codec
ID
Clock
Source
Clock
Rate
(MHz)
PLL
Active
Primary
Primary
Primary
Primary
Primary
Secondary
Secondary
Secondary
0
0
0
0
0
1
2
3
External
External
External
External
XTAL
BIT_CLK
BIT_CLK
BIT_CLK
24.576
14.31818
27.000
48.000
24.576
12.288
12.288
12.288
No
Yes
Yes
Yes
No
No
No
No
Application Notes
clock generator driving XTL_IN
external clock source driving XTL_IN
loop filter connected to XTL_OUT
crystal connected to XTL_IN, XTL_OUT
BIT_CLK from primary codec driving
BIT_CLK on all secondary codecs
Table 18. Clocking Configurations for the CS4202
DS549PP1
49
CS4202
10. ANALOG HARDWARE
DESCRIPTION
The analog input section consists of four stereo
line-level
inputs
(LINE_L/R,
CD_L/C/R,
VIDEO_L/R, and AUX_L/R), two selectable
mono microphone inputs (MIC1 and MIC2), and
two mono inputs (PC_BEEP and PHONE). The analog output section consists of a mono output
(MONO_OUT), a stereo headphone output
(HP_OUT_L/R), and a stereo line-level output
(LINE_OUT_L/R). This section describes the analog hardware needed to interface with these pins.
The designs presented in this section are compliant
with Chapter 17 of Microsoft’s PC 99 System Design Guide [7] (referred to as PC 99) and Chapter
11 of Microsoft’s PC 2001 System Design Guide
[8] (referred to as PC 2001). For information on
EMI reduction techniques refer to the application
note AN165: CS4297A/CS4299 EMI Reduction
Techniques [5].
10.1
Analog Inputs
All analog inputs to the CS4202, including CD_C,
should be capacitively coupled to the input pins.
Unused analog inputs should be tied together and
connected through a capacitor to analog ground or
tied to the Vrefout pin directly. The maximum allowed voltage for analog inputs, except the microphone input, is 1 VRMS. The maximum allowed
voltage for the microphone input depends on the
selected boost setting.
10.1.1 Line Inputs
Figure 18 shows circuitry for a line-level stereo input. Replicate this circuit for the Video and Aux inputs. This design attenuates the input by 6 dB,
bringing the signal from the PC 99 specified
2 VRMS, to the CS4202 maximum allowed 1 VRMS.
10.1.2 CD Input
The CD line-level input has an extra pin, CD_C,
providing a pseudo-differential input for both
50
CD_L and CD_R. This pin takes the
common-mode noise out of the CD inputs when
connected to the CD analog source ground. Following the reference design in Figure 19 provides extra
attenuation of common mode noise coming from
the CD-ROM drive, thereby producing a higher
quality signal. One percent resistors are recommended since closely matched resistor values provide better common-mode attenuation of unwanted
signals. The circuit shown in Figure 19 can be used
for a 1 VRMS CD input signal.
1.0 µ F
6.8 kΩ
1.0 µ F
6.8 kΩ
LINE_IN_R
LINE_IN_L
6.8 kΩ
AGND
6.8 kΩ
AGND
Figure 18. Line Input (Replicate for Video and AUX)
CD_R
CD_L
CD_COM
1.0 µ F
100 Ω
1.0 µF
100 Ω
2.2 µ F
100 Ω
47 kΩ
CD_R
CD_L
CD_C
47 kΩ
47 kΩ
AGND
Figure 19. Differential 1 VRMS CD Input
10.1.3 Microphone Inputs
Figure 20 illustrates an input circuit suitable for dynamic and electret microphones. Electret, also
known as phantom-powered, microphones use the
right channel (ring) of the jack for power. The design also supports the recommended advanced frequency response for voice recognition as specified
in PC 99 and PC 2001. The microphone input of the
CS4202 has an integrated pre-amplifier. Using
combinations of the 10dB bit in the Misc. Crystal
Control Register (Index 60) and the 20dB bit in the
DS549PP1
CS4202
Mic Volume Register (Index 0Eh) the pre-amplifier
gain can be set to 0 dB, 10 dB, 20 dB, or 30 dB.
10.1.4 PC Beep Input
The PC_BEEP input is useful for mixing the output
of the “beeper” (timer chip), provided in most PCs,
with the other audio signals. When the CS4202 is
held in reset, PC_BEEP is passed directly to the line
output. This allows the system sounds or “beeps” to
be available before the AC ’97 interface has been activated. Figure 21 illustrates a typical input circuit for
the PC_BEEP input. If PC_BEEP is driven from a
CMOS gate, the 4.7 kΩ resistor should be tied to analog ground instead of +5VA. Although this input is
described for a low-quality “beeper”, it is of the same
high-quality as all other analog inputs and may be
used for other purposes.
+5VA
1.5 kΩ
+
2.2 kΩ
10 µ F
ELEC
AGND
0.1 µF
X7R
100 Ω
MIC1/MIC2
0.1 µ F
AGND
X7R
AGND
10.1.5 Phone Input
One application of the PHONE input is to interface
to the output of a modem analog front end (AFE) device so that modem dialing signals and protocol negotiations may be monitored through the audio
system. Figure 22 shows a design for a modem connection where the output is fed from the CS4202
MONO_OUT pin through a divider. The divider ratio shown does not attenuate the signal, providing an
output voltage of 1 VRMS. If a lower output voltage
is desired, the resistors can be replaced with appropriate values, as long as the total load on the output
is kept greater than 10 kΩ. The PHONE input is divided by 6 dB to accommodate a line-level source of
2 VRMS.
10.2
Analog Outputs
The analog output section provides a stereo, a headphone, and a mono output. The MONO_OUT,
LINE_OUT_L, and LINE_OUT_R pins require
680 pF to 1000 pF NPO dielectric capacitors between the corresponding pin and analog ground.
Each analog output is DC-biased up to the Vrefout
voltage signal reference, nominally 2.4 V. This requires the outputs be AC-coupled to external circuitry (AC loads must be greater than 10 kΩ for the line
output or 32 Ω for the headphone output). The headphone coupling capacitors should be 220 µF or greater to minimize low frequency roll-off.
10.2.1 Stereo Outputs
Figure 20. Microphone Input
The LINE_OUT and HP_OUT stereo outputs depend on the configuration of the HPCFG pin. As
shown in Figure 23, if the HPCFG pin is left floating,
+5VA (Low Noise) or
AGND if CMOS Source
4.7 kΩ
47 k Ω
6.8 kΩ
1.0 µ F
PHONE
PC_BEEP
PC-BEEP-BUS
2.7 nF
X7R
0.1 µ F
MONO_OUT
PHONE
1.0 µ F
0Ω
MONO_OUT
X7R
47 kΩ
6.8 kΩ
AGND
Figure 21. PC_BEEP Input
AGND
1000 pF
AGND
Figure 22. Modem Connection
DS549PP1
51
CS4202
the part behaves as specified in AC ’97. As shown in
Figure 24, if the HPCFG pin is grounded, the part behaves as if HP_OUT was the only output. In this
case, LINE_OUT will be muted, the Master Volume
Register (Index 02h) will control HP_OUT and
PC_BEEP will be routed to HP_OUT during RESET.
10.2.2 Mono Output
The mono output, MONO_OUT, can be either a sum
of the left and right output channels, attenuated by
6 dB to prevent clipping at full scale, or the selected
Mic signal. The mono out channel can drive the PC
internal mono speaker using an appropriate buffer
circuit.
10.3
LINE_OUT_R
+
10 µ F
ELEC
LINE_OUT_L
+
10 µ F
ELEC
220 k Ω
1000 pF 1000 pF
AGND
HP_OUT_R
+
220 µ F
ELEC
HP_OUT_L
+
220 µ F
ELEC
HP_OUT_C
+
1 µF
ELEC
10 k Ω
Line Out
Jack
220 k Ω
AGND
AGND
Headphone
Jack
10 k Ω
HPCFG
AGND
AGND
Figure 23. Line Out and Headphone Out Setup
The AFLT1 and AFLT2 pins must have a 1000 pF
NPO capacitor to analog ground. These capacitors
provide a single-pole low-pass filter at the inputs to
the ADCs. This makes low-pass filters at each analog
input pin unnecessary.
The REFFLT pin must have a short, wide trace to a
2.2 µF and a 0.1 µF capacitor connected to analog
ground (see Figure 26 in Section 11, Grounding and
Layout, for an example). The 2.2 µF capacitor must
not be replaced by any other value (it may be replaced with two 1 µF capacitors in parallel) and must
be ceramic with low leakage current. Electrolytic capacitors should not be used. No other connection
should be made, as any coupling onto this pin will
degrade the analog performance of the CS4202.
Likewise, digital signals should be kept away from
REFFLT for similar reasons.
10.4
LINE_OUT_R
LINE_OUT_L
HP_OUT_R
+
220 µ F
ELEC
HP_OUT_L
+
220 µ F
ELEC
HP_OUT_C
+
1 µF
ELEC
10 k Ω
Line Out/
Headphone
Jack
10 k Ω
HPCFG
AGND
AGND
AGND
Figure 24. Line Out/Headphone Out Setup
52
Miscellaneous Analog Signals
Power Supplies
The power supplies providing analog power should
be as clean as possible to minimize coupling into the
analog section which could degrade analog performance. The +5 V analog supply should be generated
from a voltage regulator (7805 type) connected to a
+12 V supply. This helps isolate the analog circuitry
from noise typically found on +5 V digital supplies.
A typical voltage regulator circuit for analog power
using an MC78M05CDT is shown in Figure 25. One
analog power pin, AVdd2, supplies power to the
headphone amplifier on the CS4202. The other analog power pin, AVdd1, supplies power to the rest of
the CS4202 analog circuitry. The digital power pins,
DVdd1 and DVdd2, should be connected to the same
DS549PP1
CS4202
Reference Design
+5VA
MC78M05CDT
1
0.1 µF
Y5V
IN
OUT
3
GND
10 µF
ELEC
2
+
10.5
+12VD
+
digital supply as the controller’s AC-link interface.
Since the digital interface on the CS4202 may operate at either +3.3 V or +5 V, proper connection of
these pins will depend on the digital power supply of
the controller.
0.1 µF
Y5V
10 µF
ELEC
See Section 14 for a CS4202 reference design.
DGND
AGND
Figure 25. +5V Analog Voltage Regulator
DS549PP1
53
CS4202
11. GROUNDING AND LAYOUT
Figure 26 on page 55 shows the conceptual layout
for the CS4202 in XTAL or OSC clocking modes.
The decoupling capacitors should be located physically as close to the pins as possible. Also, note the
connection of the REFFLT decoupling capacitors
to the ground return trace connected directly to the
ground return pin, AVss1.
It is strongly recommended that separate analog
and digital ground planes be used. Separate ground
planes keep digital noise and return currents from
modulating the CS4202 ground potential and degrading performance. The digital ground pins
should be connected to the digital ground plane and
kept separate from the analog ground connections
of the CS4202 and any other external analog circuitry. All analog components and traces should be
located over the analog ground plane and all digital
components and traces should be located over the
digital ground plane.
tion traces should be routed such that the digital
ground plane lies underneath these signals (on the
internal ground layer). This applies along the entire
length of these traces from the AC ’97 controller to
the CS4202.
Refer to the Application Note AN18: Layout and
Design Rules for Data Converters and Other
Mixed Signal Devices [2] for more information on
layout and design rules.
The common connection point between the two
ground planes (required to maintain a common
ground voltage potential) should be located under
the CS4202. The AC-link digital interface connec-
54
DS549PP1
CS4202
1000 pF
NPO
Vrefout
toVia
Via to +5VA
2.2 µF
0.1 µF
Y5V
Via to +5VA
AFLT2
AFLT1
AVss1
REFFLT
0.1 µF
Y5V
AVdd1
Via to Analog
Ground
AVdd2
Analog
Ground
Via to Analog
Ground
AVss2
Digital
Ground
Via to Digital Ground
Pin 1
DVdd1
0.1 µF
Y5V
DVss1
DVss2
0.1 µF
Y5V
DVdd2
Via to +5VD or +3.3VD
Via to +5VD or +3.3VD
Figure 26. Conceptual Layout for the CS4202 when in XTAL or OSC Clocking Modes
DS549PP1
55
CS4202
LINE_OUT_R
LINE_OUT_L
GPIO4/SDO2
GPIO3
GPIO2
HPCFG
AFLT2
AFLT1
Vrefout
REFFLT
AVss1
AVdd1
12. PIN DESCRIPTIONS
36
35
34
33
32
31
30
29
28
27
26
25
MONO_OUT
37
24
LINE_IN_R
AVdd2
38
23
LINE_IN_L
HP_OUT_L
39
22
MIC2
HP_OUT_C
40
21
MIC1
HP_OUT_R
41
20
CD_R
AVss2
42
19
CD_C
GPIO0/LRCLK
43
18
CD_L
GPIO1/SDOUT
44
17
VIDEO_R
ID0#
45
16
VIDEO_L
ID1#
46
15
AUX_R
EAPD/SCLK
47
14
AUX_L
SPDIF_OUT
48
13
PHONE
4
5
6
7
8
9
10
11
12
SDATA_OUT
BIT_CLK
DVss2
SDATA_IN
DVdd2
SYNC
RESET#
PC_BEEP
XTL_IN
3
DVss1
2
XTL_OUT
1
DVdd1
CS4202 48-pin
Package Layout
Figure 27. Pin Locations for the CS4202
56
DS549PP1
CS4202
Audio I/O Pins
PC_BEEP - Analog Mono Source, Input, Pin 12
The PC_BEEP input is intended to allow the PC system POST (Power On Self-Test) tones to pass
through to the audio subsystem. The PC_BEEP input has two connections: the first connection is to the
analog output mixer, the second connection is directly to the LINE_OUT stereo outputs (if HPCFG is
floating) or through the headphone amplifier to the HP_OUT pins (if HPCFG is tied low). While the
RESET# pin is actively being asserted to the CS4202, the PC_BEEP bypass path to the LINE_OUT or
HP_OUT outputs is enabled. While the CS4202 is in normal operation mode with RESET# de-asserted,
PC_BEEP is a monophonic source to the analog output mixer. The maximum allowable input is 1 VRMS
(sinusoidal). This input is internally biased at the Vrefout voltage reference and requires AC-coupling to
external circuitry. If this input is not used, it should be connected to the Vrefout pin or AC-coupled to
analog ground.
PHONE - Analog Mono Source, Input, Pin 13
This analog input is a monophonic source to the output mixer. It is intended to be used as a modem
subsystem input to the audio subsystem. The maximum allowable input is 1 VRMS (sinusoidal). This
input is internally biased at the Vrefout voltage reference and requires AC-coupling to external circuitry.
If this input is not used, it should be connected to the Vrefout pin or AC-coupled to analog ground.
MIC1 - Analog Mono Source, Input, Pin 21
This analog input is a monophonic source to the analog output mixer. It is intended to be used as a
desktop microphone connection to the audio subsystem. The CS4202 internal mixer's microphone input
is MUX selectable with either MIC1 or MIC2 as the input.The maximum allowable input is 1 VRMS
(sinusoidal). This input is internally biased at the Vrefout voltage reference and requires AC-coupling to
external circuitry. If this input is not used, it should be connected to the Vrefout pin or AC-coupled to
analog ground.
MIC2 - Analog Mono Source, Input, Pin 22
This analog input is a monophonic source to the analog output mixer. It is intended to be used as an
alternate microphone connection to the audio subsystem. The CS4202 internal mixer's microphone input
is MUX selectable with either MIC1 or MIC2 as the input. The maximum allowable input is 1 VRMS
(sinusoidal). This input is internally biased at the Vrefout voltage reference and requires AC-coupling to
external circuitry. If this input is not used, it should be connected to the Vrefout pin or AC-coupled to
analog ground.
LINE_IN_L, LINE_IN_R - Analog Line Source, Inputs, Pins 23 and 24
These inputs form a stereo input pair to the CS4202. The maximum allowable input is 1 V RMS
(sinusoidal). These inputs are internally biased at the Vrefout voltage reference and require AC-coupling
to external circuitry. If these inputs are not used, they should both be connected to the Vrefout pin or
AC-coupled to analog ground.
CD_L, CD_R - Analog CD Source, Inputs, Pins 18 and 20
These inputs form a stereo input pair to the CS4202. It is intended to be used for the Red Book CD
audio connection to the audio subsystem. The maximum allowable input is 1 VRMS (sinusoidal). These
inputs are internally biased at the Vrefout voltage reference and require AC-coupling to external circuitry.
If these inputs are not used, they should both be connected to the Vrefout pin or AC-coupled to analog
ground.
CD_C - Analog CD Common Source, Input, Pin 19
This analog input is used to remove common mode noise from Red Book CD audio signals. The
impedance on the input signal path should be one half the impedance on the CD_L and CD_R input
paths. This pin requires AC-coupling to external circuitry. If this input is not used, it should be connected
to the Vrefout pin or AC-coupled to analog ground.
DS549PP1
57
CS4202
VIDEO_L, VIDEO_R - Analog Video Audio Source, Inputs, Pins 16 and 17
These inputs form a stereo input pair to the CS4202. It is intended to be used for the audio signal
output of a video device. The maximum allowable input is 1 V RMS (sinusoidal). These inputs are
internally biased at the Vrefout voltage reference and require AC-coupling to external circuitry. If these
inputs are not used, they should both be connected to the Vrefout pin or AC-coupled to analog ground.
AUX_L, AUX_R - Analog Auxiliary Source, Inputs, Pins 14 and 15
These inputs form a stereo input pair to the CS4202. The maximum allowable input is 1 V RMS
(sinusoidal). These inputs are internally biased at the Vrefout voltage reference and require AC-coupling
to external circuitry. If these inputs are not used, they should both be connected to the Vrefout pin or
AC-coupled to analog ground.
LINE_OUT_L, LINE_OUT_R - Analog Line-Level, Outputs, Pins 35 and 36
These signals are analog outputs from the stereo output mixer. The full-scale output voltage for each
output is nominally 1 VRMS (sinusoidal). These outputs are internally biased at the Vrefout voltage
reference and require either AC-coupling to external circuitry or DC-coupling to a buffer op-amp biased
at the Vrefout voltage. These pins need a 680-1000 pF NPO capacitor attached to analog ground.
HP_OUT_L, HP_OUT_R - Analog Headphone, Outputs, Pins 39 and 41
These signals are analog outputs from the stereo output mixer. The full-scale output voltage for each
output is nominally 4 Vpp. These outputs are internally biased at the Vrefout voltage reference and
require AC-coupling to external circuitry. The HP_OUT pins can directly drive resistive loads as low as
32 Ω (such as standard consumer headphones). Capacitive loading must not exceed 200 pF per pin.
The outputs are short circuit protected for infinite duration.
HP_OUT_C - Analog Headphone Output Common Source, Input, Pin 40
This analog input is used to remove common mode noise from the headphone outputs. This is achieved
by biasing the headphone amplifier with the common mode noise on the headphone amplifier ground
plane. This pin should be AC-coupled through a 1 µF electrolytic capacitor to analog ground (AVss2)
near the headphone jack.
MONO_OUT - Analog Mono Line-Level, Output, Pin 37
This signal is an analog output from the stereo-to-mono mixer. The full-scale output voltage for this
output is nominally 1 VRMS (sinusoidal). This output is internally biased at the Vrefout voltage reference
and requires either AC-coupling to external circuitry or DC-coupling to a buffer op-amp biased at the
Vrefout voltage. This pin needs a 680-1000 pF NPO capacitor attached to analog ground.
Analog Reference, Filter, and Configuration Pins
REFFLT - Internal Reference Voltage, Input, Pin 27
This signal is the voltage reference used internal to the CS4202. A 0.1 µF and a 2.2 µF ceramic
capacitor with short, wide traces must be connected to this pin. No other connections should be made
to this pin. Do not use an electrolytic 2.2 µF capacitor, use a type Z5U or Y5V ceramic capacitor.
Vrefout - Voltage Reference, Output, Pin 28
All analog inputs and outputs are centered around Vrefout, nominally 2.4 Volts. This pin may be used to
bias external amplifiers. It can also drive up to 5 mA of DC which can be used for microphone bias.
58
DS549PP1
CS4202
AFLT1 - Left ADC Channel Antialiasing Filter, Input, Pin 29
This pin needs a 1000 pF NPO capacitor connected to analog ground.
AFLT2 - Right ADC Channel Antialiasing Filter, Input, Pin 30
This pin needs a 1000 pF NPO capacitor connected to analog ground.
HPCFG - Headphone Configuration, Input, Pin 31
This pin is the configuration control for the signal routing to the headphone amplifier. If this pin is left
floating, the LINE_OUT and HP_OUT pins function as defined in the AC ’97 specification. If the HPCFG
pin is grounded, the HP_OUT pins behave as a buffered line output. In addition, the LINE_OUT pins are
muted, the control register for the headphone output will be the Master Output Volume Register (Index
02h), and PC_BEEP is routed to the HP_OUT pins during RESET. The HPCFG pin is internally pulled
up to the analog supply voltage.
AC-Link Pins
RESET# - AC ’97 Chip Reset, Input, Pin 11
This active low signal is the asynchronous Cold Reset input to the CS4202. The CS4202 must be reset
before it can enter normal operating mode.
SYNC - AC-Link Serial Port Sync Pulse, Input, Pin 10
SYNC is the serial port timing signal for the AC-link. Its period is the reciprocal of the maximum sample
rate, 48 kHz. The signal is generated by the controller and is synchronous to BIT_CLK. SYNC is an
asynchronous input when the CS4202 is configured as a primary codec and is in a PR4 powerdown
state. A series terminating resistor of 47 Ω should be connected on this signal close to the controller.
BIT_CLK - AC-Link Serial Port Master Clock, Input/Output, Pin 6
This input/output signal controls the master clock timing for the AC-link. In primary mode, this signal is a
12.288 MHz output clock derived from either a 24.576 MHz crystal or from the internal PLL based on
the XTL_IN input clock. When the CS4202 is in secondary mode, this signal is an input which controls
the AC-link serial interface and generates all internal clocking including the AC-link serial interface
timing and the analog sampling clocks. A series terminating resistor of 47 Ω should be connected on
this signal close to the CS4202 in primary mode or close to the BIT_CLK source in secondary mode.
SDATA_OUT - AC-Link Serial Data Input Stream to AC ’97, Input, Pin 5
This input signal receives the control information and digital audio output streams. The data is clocked
into the CS4202 on the falling edge of BIT_CLK. A series terminating resistor of 47 Ω should be
connected on this signal close to the controller.
SDATA_IN - AC-Link Serial Data Output Stream from AC ’97, Output, Pin 8
This output signal transmits the status information and digital audio input streams from the ADCs. The
data is clocked out of the CS4202 on the rising edge of BIT_CLK. A series terminating resistor of 47 Ω
should be connected on this signal close to the CS4202.
DS549PP1
59
CS4202
Clock and Configuration Pins
XTL_IN - Crystal Input / Clock Input, Pin 2
This pin requires either a 24.576 MHz crystal, with the other pin attached to XTL_OUT, or an external
CMOS clock. XTL_IN must have a crystal or clock source attached for proper operation except when
operating in secondary codec mode. The crystal frequency must be 24.576 MHz and designed for
fundamental mode, parallel resonance operation. If an external CMOS clock is used to drive this pin, it
must run at one of these acceptable frequencies: 14.31818, 24.576, 27, or 48 MHz. When configured as
a secondary codec, all timing is derived from the BIT_CLK input signal and this pin should be left
floating. See Section 9, Clocking, for additional details.
XTL_OUT - Crystal Output / PLL Loop Filter, Pin 3
This pin is used for a crystal placed between this pin and XLT_IN. If an external 24.576 MHz clock is
used on XTL_IN, this pin must be left floating with no traces or components connected to it. If one of
the other acceptable clocks is used on XTL_IN, this pin must be connected to a loop filter circuit. See
Section 9, Clocking, for additional details.
ID1#, ID0# - Codec ID, Inputs, Pins 45 and 46
These pins select the Codec ID for the CS4202, as well as determine the rate of the incoming clock in
PLL mode. They are only sampled after the rising edge of RESET#. These pins are internally pulled up
to the digital supply voltage and should be left floating for logic ‘0’ or tied to digital ground for logic ‘1’.
Misc. Digital Interface Pins
SPDIF_OUT - Sony/Philips Digital Interface, Output, Pin 48
This pin generates the S/PDIF digital output from the CS4202 when the SPDIF bit in the Extended
Audio Status/Control Register (Index 2Ah) is ‘set’. This output may be used to directly drive a resistive
divider and coupling transformer to an RCA-type connector for use with consumer audio equipment.
When this function is not being used this output is driven to a logic ‘0’.
EAPD/SCLK - External Amplifier Powerdown / Serial Clock, Output, Pin 47
This pin is used to control the powerdown state of an audio amplifier external to the CS4202. The
output is controlled by the EAPD bit in the Powerdown Ctrl/Stat Register (Index 26h). It is driven as a
normal CMOS output and defaults low (‘0’) upon power-up. This pin also provides the serial clock for
both serial data ports when the SDSC bit in the Serial Port Control Register (Index 6Ah) is ‘set’.
GPIO0/LRCLK - General Purpose I/O / Left-Right Clock, Input/Output, Pin 43
This pin is a general purpose I/O pin that can be used to interface with various external circuitry. When
configured as an input, it functions as a Schmitt triggered input with 350 mV hysteresis at 5 V and
220 mV hysteresis at 3.3 V. When configured as an output, it can function as a normal CMOS output
(4 mA drive) or as an open drain output. This pin also provides the L/R clock for both serial data ports
when the SDEN bit in the Serial Port Control Register (Index 6Ah) is ‘set’. This pin powers up in the
high impedance state for backward compatibility.
GPIO1/SDOUT - General Purpose I/O / Serial Data Output, Input/Output, Pin 44
This pin is a general purpose I/O pin that can be used to interface with various external circuitry. When
configured as an input, it functions as a Schmitt triggered input with 350 mV hysteresis at 5 V and
220 mV hysteresis at 3.3 V. When configured as an output, it can function as a normal CMOS output
(4 mA drive) or as an open drain output. This pin also provides the serial data for the first serial data
port when the SDEN bit in the Serial Port Control Register (Index 6Ah) is ‘set’. This pin powers up in
the high impedance state for backward compatibility.
60
DS549PP1
CS4202
GPIO2 - General Purpose I/O, Input/Output, Pin 32
This pin is a general purpose I/O pin that can be used to interface with various external circuitry. When
configured as an input, it functions as a Schmitt triggered input with 350 mV hysteresis at 5 V and
220 mV hysteresis at 3.3 V. When configured as an output, it can function as a normal CMOS output
(4 mA drive) or as an open drain output. This pin powers up in the high impedance state for backward
compatibility.
GPIO3 - General Purpose I/O, Input/Output, Pin 33
This pin is a general purpose I/O pin that can be used to interface with various external circuitry. When
configured as an input, it functions as a Schmitt triggered input with 350 mV hysteresis at 5 V and
220 mV hysteresis at 3.3 V. When configured as an output, it can function as a normal CMOS output
(4 mA drive) or as an open drain output. This pin powers up in the high impedance state for backward
compatibility.
GPIO4/SDO2 - General Purpose I/O / Serial Data Output 2, Input/Output, Pin 34
This pin is a general purpose I/O pin that can be used to interface with various external circuitry. When
configured as an input, it functions as a Schmitt triggered input with 350 mV hysteresis at 5 V and
220 mV hysteresis at 3.3 V. When configured as an output, it can function as a normal CMOS output
(4 mA drive) or as an open drain output. This pin also provides the serial data for the second serial data
port when the SDO2 bit in the Serial Port Control Register (Index 6Ah) is ‘set’. This pin powers up in the
high impedance state for backward compatibility.
Power Supply Pins
DVdd1, DVdd2 - Digital Supply Voltage, Pins 1 and 9
Digital supply voltage for the AC-link section of the CS4202. These pins can be tied to +5 V digital or to
+3.3 V digital. The CS4202 and controller’s AC-link should share a common digital supply.
DVss1, DVss2 - Digital Ground, Pins 4 and 7
Digital ground connection for the AC-link section of the CS4202. These pins should be isolated from
analog ground currents.
AVdd1, AVdd2 - Analog Supply Voltage, Pins 25 and 38
Analog supply voltage for the analog and mixed signal section of the CS4202 (AVdd1) as well as the
headphone amplifier (AVdd2). These pins must be tied to the analog +5 V power supply. It is strongly
recommended that +5 V be generated from a voltage regulator to ensure proper supply currents and
noise immunity from the rest of the system.
AVss1, AVss2 - Analog Ground, Pins 26 and 42
Ground connection for the analog, mixed signal, and substrate sections of the CS4202 (AVss1) as well
as the headphone amplifier (AVss2). These pins should be isolated from digital ground currents.
DS549PP1
61
CS4202
13. PARAMETER AND TERM DEFINITIONS
AC ’97 Specification
Refers to the Audio Codec ’97 Component Specification Ver 2.2 published by the Intel® Corporation [6].
AC ’97 Controller or Controller
Refers to the control chip which interfaces to the audio codec AC-link. This has been also called DC ’97
for Digital Controller ’97 [6].
AC ’97 Registers or Codec Registers
Refers to the 64-field register map defined in the AC ’97 Specification.
ADC
Refers to a single Analog-to-Digital converter in the CS4202. “ADCs” refers to the stereo pair of
Analog-to-Digital converters. The CS4202 ADCs have 18-bit resolution.
Codec
Refers to the chip containing the ADCs, DACs, and analog mixer. In this data sheet, the codec is the
CS4202.
DAC
Refers to a single Digital-to-Analog converter in the CS4202. “DACs” refers to the stereo pair of
Digital-to-Analog converters. The CS4202 DACs have 20-bit resolution.
dB FS A
dB FS is defined as dB relative to full-scale. The “A” indicates an A weighting filter was used.
Differential Nonlinearity
The worst case deviation from the ideal code width. Units in LSB.
Dynamic Range (DR)
DR is the ratio of the RMS full-scale signal level divided by the RMS sum of the noise floor, in the
presence of a signal, available at any instant in time (no change in gain settings between
measurements). Measured over a 20 Hz to 20 kHz bandwidth with units in dB FS A.
FFT
Fast Fourier Transform.
Frequency Response (FR)
FR is the deviation in signal level verses frequency. The 0 dB reference point is 1 kHz. The amplitude
corner, Ac, lists the maximum deviation in amplitude above and below the 1 kHz reference point. The
listed minimum and maximum frequencies are guaranteed to be within the Ac from minimum frequency
to maximum frequency inclusive.
Fs
Sampling Frequency.
Interchannel Gain Mismatch
For the ADCs, the difference in input voltage to get an equal code on both channels. For the DACs, the
difference in output voltages for each channel when both channels are fed the same code. Units are in
dB.
62
DS549PP1
CS4202
Interchannel Isolation
The amount of 1 kHz signal present on the output of the grounded AC-coupled line input channel with 1
kHz, 0 dB, signal present on the other line input channel. Units are in dB.
Line-level
Refers to a consumer equipment compatible, voltage driven interface. The term implies a low driver
impedance and a minimum 10 kΩ load impedance.
PATHS
A-D: Analog in, through the ADCs, onto the serial link.
D-A: Serial interface inputs through the DACs to the analog output.
A-A: Analog in to Analog out (analog mixer).
PC 99
Refers to the PC 99 System Design Guide published by the Microsoft® Corporation [7].
PC 2001
Refers to the PC 2001 System Design Guide published by the Microsoft® Corporation [8].
PLL
Phase Lock Loop. Circuitry for generating a desired clock from an external clock source.
Resolution
The number of bits in the output words to the DACs, and in the input words to the ADCs.
Signal to Noise Ratio (SNR)
SNR, similar to DR, is the ratio of an arbitrary sinusoidal input signal to the RMS sum of the noise floor,
in the presence of a signal. It is measured over a 20 Hz to 20 kHz bandwidth with units in dB.
S/PDIF
Sony/Phillips Digital Interface. This interface was established as a means of digitally interconnecting
consumer audio equipment. The documentation for S/PDIF has been superseded by the IEC-958
consumer digital interface document.
SRC
Sample Rate Converter. Converts data derived at one sample rate to a differing sample rate. The
CS4202 operates at a fixed sample frequency of 48 kHz. The internal sample rate converters are used
to convert digital audio streams playing back at other frequencies to 48 kHz.
Total Harmonic Distortion plus Noise (THD+N)
THD+N is the ratio of the RMS sum of all non-fundamental frequency components, divided by the RMS
full-scale signal level. It is tested using a -3 dB FS input signal and is measured over a 20 Hz to 20 kHz
bandwidth with units in dB FS.
DS549PP1
63
J8
MIC IN
J7
PHONE IN
J4
LINE IN
J2
CD IN
1
2
1
2
3
4
AGND
R19
C21
C18
1uF
Y5V
1uF
Y5V
1uF
Y5V
1uF
Y5V
+5VA
R20
3.3V.
is tied to
GPIO3 (pin 33)
configuration
For 2 channel
DGND
C26
C27
DGND
C28
X7R
0.1uF
C10
23
24
18
19
20
14
15
12
4
7
AGND
1
2
5
3
4
AGND
DGND
R17
C30
R21
6.8K
6.8K
R16
Y5V
1uF
2.2K
AGND
6.8K
6.8K
R14
C23
1uF
Y5V
Y5V
C33
ELEC
10uF
AGND
+
1.5K
AGND
2.2uF
X7R
0.1uF
1uF capacitors.
be replaced by two
2.2uF capacitor can
Y5V
C25
C24
NO POP
NPO
1000pF
C31
22pF
NPO
DGND
AFLT1
AFLT2
REFFLT
MIC1
Vrefout
PHONE
VIDEO_L
VIDEO_R
MIC2
LINE_IN_L
LINE_IN_R
CD_L
CD_C
+3.3VD
24.576 MHz
(50 PPM)
Y1
X7R
0.1uF
C5
DGND
C32
22pF
NPO
BIT_CLK
SPDIF_OUT
GPIO4/SDO2
GPIO1/SDOUT
GPIO0/LRCLK
ID0#
ID1#
EAPD/SCLK
MONO_OUT
HPCFG
HP_OUT_C
HP_OUT_L
HP_OUT_R
GPIO2
LINE_OUT_L
LINE_OUT_R
RESET#
SDATA_IN
SYNC
SDATA_OUT
ELEC
10uF
+ C6
+5VA
AGND
SDATAIN0
SDATAOUT
48
34
44
43
46
45
47
37
31
40
39
41
32
35
36
GND_TIE
under the codec
point only
Tie at one
DGND
0.050 inch
HP SENSE
RESET#
47
SYNC
R9
10
5
8
BITCLK
Controller
or ICH
Controller
PCI Audio
AC LINK
11
R8
6
47
X7R
X7R
AGND
0.1uF
0.1uF
U2
C13
C12
Figure 28. CS4202 Reference Design
NPO
1000pF
30
29
27
21
28
16
13
AUX_L
CD_R
3
CS4202
PC_BEEP
AUX_R
DVss2
DVss1
X7R
0.1uF
C11
OUT
MC78M05ACDT
17
6.8K
1uF
X7R
0.1uF
C4
IN
U1
1
R12
6.8K
C15
C9
C7
AGND
ELEC
1
22
AGND
100K
R7
R11
100K
100K
R5
R3
AGND
10uF
X7R
+ C3
2700pF
C2
+12V
GND
2
2
5
3
4
AGND
DGND
R2
4.7K
X7R
33
GPIO3
0.1uF
9
DVdd2
C1
1
DVdd1
1
47K
AVss1
R1
42
AVss2
2
25
AVdd1
J1
XTL_IN
2
26
XTL_OUT
3
38
AVdd2
64
C22
C20
C19
+
+
BEEP IN
1uF
Y5V
ELEC
220uF
ELEC
220uF
R15
R13
1uF
10K
+5VD
1000pF
NPO
C17
10K
1000pF
NPO
Y5V
1uF
Y5V
C16
C14
C8
AGND
220K
220K
X7R
0.1uF
C29
AGND
DGND
R6
R4
R18
6.8K
DGND
DGND
R10
10K
+3.3VD
AGND
J3
JACK
6
5
1
2
3
4
1
3
2
6
7
J5
J6
S/PDIF OUT
JACK
HEADPHONE
1
2
5
3
4
LINE OUT
CS4202
14. REFERENCE DESIGN
DS549PP1
CS4202
15. REFERENCES
1) Cirrus Logic, Audio Quality Measurement Specification, Version 1.0, 1997
http://www.cirrus.com/products/papers/meas/meas.html
2) Cirrus Logic, AN18: Layout and Design Rules for Data Converters and Other Mixed Signal Devices,
Version 6.0, February 1998
3) Cirrus Logic, AN22: Overview of Digital Audio Interface Data Structures, Version 2.0, February 1998
4) Cirrus Logic, AN134: AES and S/PDIF Recommended Transformers, Version 2, April 1999
5) Cirrus Logic, AN165: CS4297A/CS4299 EMI Reduction Techniques, Version 1.0, September 1999
6) Intel®, Audio Codec ’97 Component Specification, Revision 2.2, September 2000
http://developer.intel.com/ial/scalableplatforms/audio/index.htm
7) Microsoft®, PC 99 System Design Guide, Version 1.0, July 1999
http://www.microsoft.com/hwdev/desguid/
8) Microsoft®, PC 2001 System Design Guide, Version 1.0, November 2000
http://www.pcdesguide.org/pc2001/default.htm
9) Intel® 82801AA (ICH) and 82801AB (ICH0) I/O Controller Hub, June 1999
http://developer.intel.com/design/chipsets/datashts/290655.htm
10) Intel® 82801BA (ICH2) I/O Controller Hub, October 2000
http://developer.intel.com/design/chipsets/datashts/290687.htm
11) Intel® 82801CAM (ICH3-M) I/O Controller Hub, July 2001
http://developer.intel.com/design/chipsets/datashts/290716.htm
DS549PP1
65
CS4202
16. PACKAGE DIMENSIONS
48L LQFP PACKAGE DRAWING
E
E1
D D1
1
e
B
∝
A
A1
L
DIM
A
A1
B
D
D1
E
E1
e*
L
MIN
--0.002
0.007
0.343
0.272
0.343
0.272
0.016
0.018
0.000°
∝
* Nominal pin pitch is 0.50 mm
INCHES
NOM
0.055
0.004
0.009
0.354
0.28
0.354
0.28
0.020
0.24
4°
MAX
0.063
0.006
0.011
0.366
0.280
0.366
0.280
0.024
0.030
7.000°
MIN
--0.05
0.17
8.70
6.90
8.70
6.90
0.40
0.45
0.00°
MILLIMETERS
NOM
1.40
0.10
0.22
9.0 BSC
7.0 BSC
9.0 BSC
7.0 BSC
0.50 BSC
0.60
4°
MAX
1.60
0.15
0.27
9.30
7.10
9.30
7.10
0.60
0.75
7.00°
Controlling dimension is mm.
JEDEC Designation: MS022
66
DS549PP1
• Notes •
Similar pages