Cirrus CS4222-KS 20-bit stereo audio codec with volume control Datasheet

CS4222
20-Bit Stereo Audio Codec with Volume Control
Features
Description
99 dB Dynamic Range
110 dB DAC Signal-to-Noise Ratio (EIAJ)
Analog Volume Control
- 0.5 dB Step Resolution
- 113.5 dB Attenuation
Soft Mute Capability
Differential Inputs/Outputs
On-chip Anti-aliasing and Output Smoothing
Filters
De-emphasis for 32, 44.1 and 48 kHz
Stand-Alone or Control Port Mode
Single +5 V power supply
The CS4222 is a highly integrated, high performance,
20-bit, audio codec providing stereo analog-to-digital
and stereo digital-to-analog converters using delta-sigma conversion techniques. The device operates from a
single +5 V power supply, and features low power consumption. A selectable de-emphasis filter for 32, 44.1,
and 48 kHz sample rates is also included.
The CS4222 also includes an analog volume control capable of 113.5 dB attenuation in 0.5 dB resolution. The
analog volume control architecture preserves dynamic
range during attenuation. Volume control changes are
implemented using a "soft" ramping or zero crossing
technique.
Applications include reverb processors, musical instruments, DAT, and multitrack recorders.
The CS4222 is packaged in a 28-pin plastic SSOP.
ORDERING INFORMATION
CS4222-KS
-10° to +70° C
28-pin SSOP
CS4222-BS
-40° to +85° C
28-pin SSOP
CS4222-DS
-40° to +85° C
28-pin SSOP
CDB4222
Evaluation Board
I
SCL/CCLK SDA/CDIN
AD0/CS
SMUTE
MCLK
VD
VA
Control Port
RST
SDIN
SDOUT
Left
DAC
Volume
Control
Right
DAC
Volume
Control
AOUTL+
AOUTLAOUTR+
AOUTR-
Left
ADC
AINLAINL+
Right
ADC
AINRAINR+
DGND
http://www.cirrus.com
Analog Low
Pass and
Output Stage
Digital Filters
with De-Emphasis
SCLK
Digital Filters
LRCK
Serial Audio Data Interface
DEM1
DEM0
AGND
Copyright  Cirrus Logic, Inc. 2002
(All Rights Reserved)
DEC ‘02
DS236F1
1
CS4222
TABLE OF CONTENTS
1. PIN DESCRIPTION ...............................................................................4
2. CHARACTERISTICS AND SPECIFICATIONS .................................... 6
SPECIFIED OPERATING CONDITIONS ................................................................................. 6
ABSOLUTE MAXIMUM RATINGS ........................................................................................... 6
ANALOG INPUT CHARACTERISTICS .................................................................................... 7
ANALOG OUTPUT CHARACTERISTICS ................................................................................ 8
SWITCHING SPECIFICATIONS - SERIAL AUDIO INTERFACE............................................. 9
SWITCHING SPECIFICATIONS - CONTROL PORT INTERFACE (SPI) .............................. 10
SWITCHING SPECIFICATIONS - CONTROL PORT INTERFACE (I2C) .............................. 11
DC ELECTRICAL CHARACTERISTICS................................................................................. 12
DIGITAL INPUT CHARACTERISTICS ................................................................................... 12
DIGITAL INTERFACE SPECIFICATIONS.............................................................................. 12
3. TYPICAL CONNECTION DIAGRAM ................................................. 13
4. APPLICATIONS .................................................................................. 14
4.1 Overview .......................................................................................................................... 14
4.2 Analog Inputs ................................................................................................................... 14
4.2.1 Line Level Inputs ................................................................................................. 14
4.2.2 Input Level Monitoring ......................................................................................... 16
4.2.3 High Pass Filter ................................................................................................... 16
4.3 Analog Outputs ................................................................................................................ 16
4.3.1 Line Level Outputs .............................................................................................. 16
4.3.2 Analog/Digital Volume Control (Control Port Mode only) .................................... 18
4.3.3 Soft Mute/Mute on Zero Input Data ..................................................................... 18
4.4 Master Clock Generation ................................................................................................. 19
4.4.1 MCLK Timing Constraint ..................................................................................... 19
4.5 Serial Audio Data Interface .............................................................................................. 19
4.5.1 Serial Audio Interface Signals ............................................................................. 19
4.5.2 Serial Audio Interface Formats ............................................................................ 19
Contacting Cirrus Logic Support
For all product questions and inquiries contact a Cirrus Logic Sales Representative.
To find one nearest you go to http://www.cirrus.com/corporate/contacts/sales.cfm
IMPORTANT NOTICE
"Preliminary" product information describes products that are in production, but for which full characterization data is not yet available. "Advance" product information describes products that are in development and subject to development changes. Cirrus Logic, Inc. and its subsidiaries ("Cirrus") believe that the information contained in this document is accurate and reliable. However, the information is subject to change without notice and is provided "AS IS" without warranty
of any kind (express or implied). Customers are advised to obtain the latest version of relevant information to verify, before placing orders, that information being
relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those
pertaining to warranty, patent infringement, and limitation of liability. No responsibility is assumed by Cirrus for the use of this information, including use of this
information as the basis for manufacture or sale of any items, or for infringement of patents or other rights of third parties. This document is the property of Cirrus
and by furnishing this information, Cirrus grants no license, express or implied under any patents, mask work rights, copyrights, trademarks, trade secrets or
other intellectual property rights. Cirrus owns the copyrights of the information contained herein and gives consent for copies to be made of the information only
for use within your organization with respect to Cirrus integrated circuits or other parts of Cirrus. This consent does not extend to other copying such as copying
for general distribution, advertising or promotional purposes, or for creating any work for resale.
An export permit needs to be obtained from the competent authorities of the Japanese Government if any of the products or technologies described in this material and controlled under the "Foreign Exchange and Foreign Trade Law" is to be exported or taken out of Japan. An export license and/or quota needs to be
obtained from the competent authorities of the Chinese Government if any of the products or technologies described in this material is subject to the PRC Foreign
Trade Law and is to be exported or taken out of the PRC.
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE
PROPERTY OR ENVIRONMENTAL DAMAGE ("CRITICAL APPLICATIONS"). CIRRUS PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF CIRRUS PRODUCTS
IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER'S RISK.
Purchase of I2C components of Cirrus Logic, Inc., or one of its sublicensed Associated Companies conveys a license under the Phillips I2C Patent Rights to use
those components in a standard I2C system.
Cirrus Logic, Cirrus, and the Cirrus Logic logo designs are trademarks of Cirrus Logic, Inc. All other brand and product names in this document may be trademarks or service marks of their respective owners.
2
DS236F1
CS4222
4.6 Control Port Interface ...................................................................................................... 21
4.6.1 SPI Mode ............................................................................................................ 21
4.6.2 I2C Mode ............................................................................................................. 22
4.6.3 Control Port Bit Definitions .................................................................................. 22
4.7 De-Emphasis ................................................................................................................... 22
4.8 Power-up / Reset / Power Down / Calibration ................................................................. 23
4.9 Power Supply, Layout and Grounding ............................................................................. 23
4.10 ADC and DAC Filter Response Plots ............................................................................ 24
5. REGISTER DESCRIPTIONS .............................................................. 25
5. Memory Address Pointer (MAP) ......................................................................................... 25
5. Reserved Byte (0)............................................................................................................... 25
5. ADC Control Byte (1) .......................................................................................................... 25
5. DAC Control Byte (2) .......................................................................................................... 26
5. Output Attenuator Data Byte (3, 4) ..................................................................................... 26
5. DSP Port Mode Byte (5) ..................................................................................................... 27
5. Converter Status Report Byte (Read Only) (6) ................................................................... 27
6. PARAMETER DEFINITIONS .............................................................. 28
7. PACKAGE DIMENSIONS ................................................................... 29
LIST OF FIGURES
Figure 1. Serial Audio Interface Timing........................................................................................... 9
Figure 2. Control Port Timing - SPI Mode ..................................................................................... 10
Figure 3. Control Port Timing - I2C Mode ..................................................................................... 11
Figure 4. CS4222 Recommended Connection Diagram............................................................... 13
Figure 5. Optional Line Input Buffer .............................................................................................. 15
Figure 6. Full Scale Input/Output Voltage ..................................................................................... 15
Figure 7. 2- and 3-Pole Butterworth Filters ................................................................................... 17
Figure 8. Hybrid Analog/Digital Attenuation .................................................................................. 18
Figure 9. Audio DSP Data Input Formats...................................................................................... 20
Figure 10. Audio DSP Data Output Formats................................................................................. 20
Figure 11. Control Port Timing, SPI mode .................................................................................... 21
Figure 12. Control Port Timing, I2C mode ..................................................................................... 22
Figure 13. De-emphasis Curve. .................................................................................................... 22
Figure 14. ADC Filter Response ................................................................................................... 24
Figure 15. ADC Passband Ripplee ............................................................................................... 24
Figure 16. ADC Transition Band ................................................................................................... 24
Figure 17. DAC Filter Response ................................................................................................... 24
Figure 18. DAC Passband Ripple ................................................................................................. 24
Figure 19. DAC Transition Band ................................................................................................... 24
LIST OF TABLES
Table 1. Control Port vs. Stand-Alone Mode ....................................................................................... 14
Table 2. High Pass Filter Characteristics ............................................................................................ 16
Table 3. Common Clock Frequencies ................................................................................................. 19
Table 4. De-Emphasis filter control ..................................................................................................... 22
DS236F1
3
CS4222
1. PIN DESCRIPTION
4
NC
1
28
NC
SMUTE
2
27
RST
MCLK
3
26
AOUTL-
LRCK
4
25
AOUTL+
SCLK
5
24
AOUTR+
VD
6
23
AOUTR-
DGND
7
22
AGND
SDOUT
8
21
VA
SDIN
9
20
AINL+
SCL/CCLK
10
19
AINL-
SDA/CDIN
11
18
DEM1
AD0/CS
12
17
AINR+
DEM0
13
16
AINR-
NC
14
15
NC
DS236F1
CS4222
Pin Name
NC
#
Pin Description
1,14, No Connect - These pins are not connected internally and should be tied to DGND to minimize noise
15, 28 coupling.
SMUTE
2
Soft Mute (Input) - Activates a muting function for both the left and right channel D/A converter outputs.
Soft muting is achieved by ramping down the volume in 0.5 dB steps until achieving mute if SOFT bit
(DAC Control Byte #2) is set to 0 (default).
LRCK
4
Left/Right Clock (Input) - Determines which channel is currently being input/output of the serial audio
data pins SDIN/SDOUT. The frequency of the Left/Right clock must be equal to the input sample rate.
Although the outputs for each ADC channel are transmitted at different times, Left/Right pairs represent
simultaneously sampled analog inputs.
SCLK
5
Serial Data Clock (Input) - Clocks the individual bits of the serial data into the SDIN pin and out of the
SDOUT pin.
VD
6
Digital Power (Input) - Positive power supply for the digital section. Nominally 5.0 VDC.
DGND
7
Digital Ground (Input) - Digital ground for the digital section.
SDOUT
8
Serial Data Output (Output) - Two's complement MSB-first serial data is output on this pin.
SDIN
9
Serial Data Input (Input) - Two's complement MSB-first serial data is input on this pin.
SCL/CCLK
10
Serial Control Port Clock (Input) - Serial clock for the control port interface. This pin should be tied to
DGND in stand-alone mode.
SDA/CDIN
11
Serial Control Port Data (Input/Output) - SDA is a data I/O line in I2C mode and requires an external
pull-up resistor according to the I2C specification. CDIN in the input data line for the serial control port in
SPI mode. This pin should be tied to DGND in stand-alone mode.
AD0/CS
12
Address Bit/Control Chip Select (Input) - In I2C mode, AD0 is a chip address bit. In SPI mode, CS is
used to enable the control port interface on the CS4222. The CS4222 will enter SPI mode if a negative
transition is ever seen on this pin after power up. This pin should be tied to DGND in stand-alone mode.
DEM0
DEM1
13
18
De-emphasis Control (Input) - Selects the standard 15µs/50µs digital de-emphasis filter response for
32, 44.1 and 48 kHz sample rate.
AINR-,
AINR+
16,17 Differential Right Channel Analog Input (Input) - Analog input connections of the right channel differential inputs. Typically 2 Vrms differential (1 Vrms for each input pin) for a fullscale analog input signal.
AINL-,
AINL+
19,20 Differential Left Channel Analog Input (Input) - Analog input connections of the left channel differential
inputs. Typically 2 Vrms differential (1 Vrms for each input pin) for a fullscale analog input signal.
VA
21
Analog Power (Input) - Positive power supply for the analog section. Typically 5.0 VDC.
AGND
22
Analog Ground (Input) - Analog ground reference.
AOUTR-,
AOUTR+
23, 24 Differential Right Channel Analog Outputs (Output) - The full scale analog output level (differential) is
specified in the Analog Characteristics specification table.
AOUTL-,
AOUTL+
25, 26 Differential Left Channel Analog Outputs (Output) - The full scale analog output level (differential) is
specified in the Analog Characteristics specification table.
RST
DS236F1
27
Reset (Input) - When low, the device enters a low power mode and all internal registers are reset,
including the control port. When high, the control port becomes operational and normal operation will
occur.
5
CS4222
2. CHARACTERISTICS AND SPECIFICATIONS. (All Min/Max characteristics and specifications
are guaranteed over the Specified Operating Conditions. Typical performance characteristics and specifications
are derived from measurements taken at nominal supply voltages and TA = 25°C.)
SPECIFIED OPERATING CONDITIONS (AGND = DGND = 0 V; all voltages with respect to 0 V.)
Parameters
Symbol
Min
Nom
Max
Units
Analog Supply Voltage
VA
4.75
5.0
5.25
V
Digital Supply Voltage
VD
4.75
5.0
5.25
V
TA
-10
-40
-
+70
+85
°C
°C
Ambient Operating Temperature (Power Applied)
-KS
-BS/-DS
ABSOLUTE MAXIMUM RATINGS(AGND = 0 V; all voltages with respect to AGND. Operation
beyond these limits may result in permanent damage to the device. Normal operation is not guaranteed at these
extremes.)
Parameters
Symbol
Min
Max
Units
-0.3
-0.3
6.0
6.0
V
V
DC Power Supply
Analog
Digital
VA
VD
Input Current
(Note 1)
Iin
-
±10
mA
Analog Input Voltage
-0.7
VA+0.7
V
Digital Input Voltage
-0.7
VD+0.7
V
Ambient Operating Temperature (power applied)
TA
-55
125
°C
Storage Temperature
Tstg
-65
150
°C
Note:
6
1. Any pin except supplies.
DS236F1
CS4222
ANALOG INPUT CHARACTERISTICS (Test conditions (unless otherwise specified): Input test
signal is a 997 Hz sine wave; measurement bandwidth is 10 Hz to 20 kHz; VD = VA, Fs=48kHz)
CS4222-KS
Parameter
CS4222-BS/-DS
Min
Typ
Max
Min
Typ
Max
Unit
95
92
99
96
-
95
92
99
96
-
dB
dB
-1 dB
-20 dB
-60 dB
-
-90
-76
-36
-86
-
-
-90
-76
-36
-86
-
dB
dB
dB
(1 kHz)
-
90
-
-
90
-
dB
(HPF Enabled)
(HPF Disabled)
-
0
20
-
-
0
20
-
mVRMS
mVRMS
Interchannel Gain Mismatch
-
0.1
-
-
0.1
-
dB
Gain Drift
-
±100
-
-
±100
-
ppm/°C
Dynamic Range
A-weighted
unweighted
Total Harmonic Distortion + Noise
Interchannel Isolation
(Note 2)
DC Accuracy
Offset Error
Analog Input
Full Scale Differential Input Voltage
1.82
2.0
2.18
1.82
2.0
2.18
VRMS
Input Resistance
-
10
-
-
10
-
kΩ
Input Capacitance
-
15
-
-
15
-
pF
Common Mode Input Voltage
-
2.3
-
-
2.3
-
V
ADC Digital Decimation Filter Characteristics (Note 3)
Parameter
Min
Typ
Max
Unit
0
-
0.4535
Fs
Passband Ripple
-0.01
-
+0.01
dB
StopBand
0.625
-
-
Fs
80
-
-
dB
Group Delay
-
15/Fs
-
s
Group Delay Variation
-
-
0
s
-3 dB
-0.1 dB
-
3.7
20
-
Hz
Hz
@ 20 Hz
-
10
-
Degree
-
-
0
dB
Passband
StopBand Attenuation
to -0.01 dB corner
(Note 4)
HPF Characteristics
Frequency Response
Phase Deviation
Passband Ripple
Notes: 2. Referenced to typical fullscale differential input voltage.
3. The filter characteristics have been normalized to the sample rate (Fs) and can be referenced to the
desired sample rate by multiplying the given characteristic by Fs.
4. The analog modulator samples the input at 6.144 MHz for an Fs equal to 48 kHz. There is no rejection
of input signals which are multiples of the sampling frequency (n x 6.144 MHz +/- 21.8 kHz; n = 0, 1, ...).
DS236F1
7
CS4222
ANALOG OUTPUT CHARACTERISTICS (Test conditions (unless otherwise specified): Input
test signal is a 997 Hz sine wave; measurement bandwidth is 10 Hz to 20 kHz; test load RL = 10 kΩ, CL = 10 pF;
VD = VA, Fs=48kHz)
CS4222-KS
Parameter
CS4222-BS/-DS
Min
Typ
Max
Min
Typ
Max
Unit
93
90
99
96
-
93
90
99
96
-
dB
dB
-
-88
-76
-36
-84
-
-
-88
-76
-36
-84
-
dB
dB
dB
Idle Channel Noise / Signal-to-noise ratio
(Note 5)
-
110
-
-
110
-
dB
Interchannel Isolation
-
90
-
-
90
-
dB
Dynamic Range
A-weighted
unweighted
Total Harmonic Distortion + Noise
0 dB
-20 dB
-60 dB
(1 kHz)
Attenuation Step Size
0.35
0.5
0.65
0.35
0.5
0.65
dB
Programmable Output Attenuation Span
110
113.5
-
110
113.5
-
dB
-
±10
-
-
±10
-
mV
DC Accuracy
Differential Offset Voltage
Interchannel Gain Mismatch
-
0.1
-
-
0.1
-
dB
Gain Drift
-
±100
-
-
±100
-
ppm/°C
1.9
2.0
2.1
1.9
2.0
2.1
VRMS
Analog Output
Full Scale Output Voltage
Common Mode Output Voltage
AC-Load resistance
Load Capacitance
-
2.3
-
-
2.3
-
V
10
-
-
10
-
-
kΩ
-
-
100
-
-
100
pF
DAC Combined Interpolation & On-Chip Analog Filter Response (Note 6)
Parameter
Passband
to 0.01 dB corner
Passband Ripple
Frequency Response 10 Hz to 20 kHz
Min
Typ
Max
Unit
0
-
0.4535
Fs
-0.01
-
+0.01
dB
-0.1
-
+0.1
dB
0.5465
-
-
Fs
70
-
-
dB
Group Delay
-
16/Fs
-
s
Deviation from Linear Phase
-
±0.5
-
Degree
StopBand
StopBand Attenuation
(Note 7)
Notes: 5. DAC muted, A-weighted
6. The filter characteristics have been normalized to the sample rate (Fs) and can be referenced to the
desired sample rate by multiplying the given characteristic by Fs.
7. Measurement bandwidth is 10 Hz to 3 Fs
8
DS236F1
CS4222
SWITCHING SPECIFICATIONS - SERIAL AUDIO INTERFACE
Parameters
Symbol
RST Low Time
MCLK Frequency
Min
Max
Units
10
-
ms
1.014
25.6
MHz
MCLK Pulse Width High
MCLK = 512 Fs
MCLK = 384 Fs
MCLK = 256 Fs
10
21
31
-
ns
MCLK Pulse Width Low
MCLK = 512 Fs
MCLK = 384 Fs
MCLK = 256 Fs
10
21
31
-
ns
4
50
kHz
-
128xFs
Hz
Input Sample Rate
Fs
SCLK Frequency
SCLK Pulse Width Low
tsckh
40
-
ns
SCLK Pulse Width High
tsckl
40
-
ns
SCLK rising to LRCK edge delay
(DSCK = 0)
tlrckd
20
-
ns
SCLK rising to LRCK edge setup time
(DSCK = 0)
tlrcks
40
-
ns
SDIN valid to SCLK rising setup time
(DSCK = 0)
tds
25
-
ns
SCLK rising to SDIN hold time
(DSCK = 0)
tdh
25
-
ns
SCLK falling to SDOUT valid
(DSCK = 0)
tdpd
-
1
---------------------- + 20
(384) Fs
s
LRCK
t lrckd
t lrcks
t sckh
t sckl
SCLK*
t sckw
SDIN
t lrpd
SDOUT
t ds
t dh
t dpd
MSB
MSB-1
*SCLK shown for DSCK = 0, SCLK inverted for DSCK = 1.
Figure 1. Serial Audio Interface Timing
DS236F1
9
CS4222
SWITCHING SPECIFICATIONS - CONTROL PORT INTERFACE (SPI)
(Inputs:
Logic 0 = DGND, Logic 1 = VD)
Parameter
Symbol
Min
Max
Unit
CCLK Clock Frequency
fsck
-
6
MHz
RST Rising Edge to CS Falling
tsrs
500
-
ns
tspi
500
-
ns
CS High Time Between Transmissions
tcsh
1.0
-
µs
CS Falling to CCLK Edge
tcss
20
-
ns
CCLK Low Time
tscl
66
-
ns
CCLK High Time
tsch
66
-
ns
CDIN to CCLK Rising Setup Time
tdsu
40
-
ns
(Note 9)
tdh
15
-
ns
Rise Time of CCLK and CDIN
(Note 10)
tr2
-
100
ns
Fall Time of CCLK and CDIN
(Note 10)
tf2
-
100
ns
SPI Mode
CCLK Edge to CS Falling
(Note 8)
CCLK Rising to DATA Hold Time
Notes: 8. tspi only needed before first falling edge of CS after RST rising edge. tspi = 0 at all other times.
9. Data must be held for sufficient time to bridge the transition time of CCLK.
10. For fsclk < 1 MHz.
RST
t srs
CS
t sp i t css
t scl
t sch
t csh
C C LK
t r2
t f2
C D IN
t dsu t dh
Figure 2. Control Port Timing - SPI Mode
10
DS236F1
CS4222
SWITCHING SPECIFICATIONS - CONTROL PORT INTERFACE (I2C) (Continued)
Parameter
Symbol
Min
Max
Unit
SCL Clock Frequency
fscl
-
100
kHz
RST Rising Edge to Start
tirs
500
-
ns
Bus Free Time Between Transmissions
tbuf
4.7
-
µs
Start Condition Hold Time (prior to first clock pulse)
thdst
4.0
-
µs
Clock Low time
tlow
4.7
-
µs
Clock High Time
thigh
4.0
-
µs
Setup Time for Repeated Start Condition
tsust
4.7
-
µs
thdd
0
-
µs
tsud
250
-
ns
Rise Time of SCL and SDA
tr
-
1
µs
Fall Time SCL and SDA
tf
-
300
ns
tsusp
4.7
-
µs
I2C
Mode
SDA Hold Time from SCL Falling
(Note 11)
SDA Setup time to SCL Rising
Setup Time for Stop Condition
Notes: 11. Data must be held for sufficient time to bridge the transition time, tfc, of SCL.
RST
t
irs
S to p
R e p e a te d
S t a rt
S t a rt
t rd
t fd
S to p
SDA
t
b uf
t
t
h dst
t
high
t fc
h d st
t susp
SCL
t
lo w
t
hd d
t su d
t a ck
t su st
t rc
Figure 3. Control Port Timing - I2C Mode
DS236F1
11
CS4222
DC ELECTRICAL CHARACTERISTICS
(AGND = DGND = 0 V; all voltages with respect to 0 V.)
Parameters
Symbol
Min
Typ
Max
Units
-
200
-
µA
IA
ID
-
30
20
40
26
mA
mA
PSRR
-
50
-
dB
Power-down Mode (Note 12)
Power Supply Current
All Supplies = 5.0 V
Normal Operation (Note 13)
Power Supply Current
VA = 5.0 V
VD = 5.0 V
Power Supply Rejection Ratio
1 kHz, 10 mVRMS
Notes: 12. Power Down Mode is defined as RST = LO with all clocks and data lines held static.
13. Normal operation is defined as RST = HI with a 997 Hz, 0dBFS digital input and a 1 kHz, -1 dB analog
input sampled at Fs = 48 kHz, and open outputs, unless otherwise specified.
DIGITAL INPUT CHARACTERISTICS
Min
Typ
Max
Units
Input Leakage Current
Parameters
-
-
10
µA
Output Leakage Current
-
-
10
µA
MCLK Jitter Tolerance
-
500
-
psRMS
DIGITAL INTERFACE SPECIFICATIONS
Parameters
Symbol
(AGND = DGND = 0 V; all voltages with respect to 0 V.)
Symbol
Min
Max
Units
High-Level Output Voltage (IOH = -2.0 mA)
VOH
VD - 1.0
-
V
Low-Level Output Voltage (IOL = 2.0 mA)
VOL
-
0.4
V
High-Level Input Voltage
VIH
2.8
VD + 0.3
V
Low-Level Input Voltage
VIL
-0.3
1.0
V
12
DS236F1
CS4222
3. TYPICAL CONNECTION DIAGRAM
F e r r it e B e a d
+ 5 .0 V
S u p p ly
+
2Ω
1 µF
0 .1 µ F
0 .1 µ F +
21
6
VA
150Ω
20
VD
A IN L +
AOUTL+
AO UTL-
2 .2 n F
150Ω
19
150Ω
17
1 µF
25
26
A n a lo g F ilt e r
24
23
A n a lo g F ilt e r
A IN LAOUTR+
AOUTR-
A IN R +
2 .2 n F
150Ω
16
C S 4 22 2
A IN R DEM 1
DEM 0
M ic r o c o n t r o ll e r
10
11
12
27
2
1
14
15
N o t e : P in s 1 0 , 1 1 a n d 1 2
s h o u ld b e t ie d t o D G N D
in s t a n d - a lo n e m o d e .
28
S C L /C C L K
S D A /C D IN
A D 0 /C S
RST
SM UTE
M CLK
SCLK
NC
LR C K
NC
S D IN
NC
SDOUT
18
13
D ig it a l A u d io
S o u rce
3
R s1
5
Rs
4
Rs
9
Rs
8
Rs
A u d io
DSP
NC
AGND
22
DGND
7
Rs1 = 50 Ω
Rs
= 50 0 Ω
Figure 4. CS4222 Recommended Connection Diagram
DS236F1
13
CS4222
4. APPLICATIONS
4.1 Overview
The CS4222 has 2 channels of 20-bit analog-to-digital conversion and 2 channels of 20-bit digital-to-analog
conversion. All ADCs and DACs are delta-sigma converters. The DAC outputs on the CS4222 have adjustable
output attenuation implemented in 0.5 dB step resolution. The device also includes digital de-emphasis for 32,
44.1, and 48 kHz.
Digital audio data for the DACs and from the ADCs is communicated over separate serial ports. This allows
concurrent writing to and reading from the device. The CS4222 is a stand-alone device controlled via pins.
Control for the functions available on the CS4222 are communicated over a serial microcontroller interface.
Figure 4 shows the recommended connection diagram for the CS4222.
The device can be operated with or without the control port interface. Additional functions are available when
the control port interface is used as outlined in Table 1.
Table 1. Control Port vs. Stand-Alone Mode
Control Port
Stand-Alone Mode
Volume control
-
Adjustable Mute ramp rate
Fixed Mute ramp rate
Enable zero crossing detect
Disabled
Enable/Disable mute on zero input
Enabled
De-emphasis
De-emphasis
Mute DAC outputs
Mute DAC outputs
ADC Input Peak Level Detect
-
16, 18, 20 bit Interface
20 bit I2S Interface
Individual ADC/DAC power down
Codec power down
Cal on command
Cal on power-up
High pass enable/disable
High pass enabled
4.2 Analog Inputs
4.2.1 Line Level Inputs
AINR-, AINR+, AINL-, and AINL+ are the differential line level input pins (see Figure 4). Figure 5 shows an
AC coupled optional input buffer which combines level shifting with single-ended to differential conversion.
Analog inputs must be DC coupled into the CS4222 with a 2.3 V common mode input voltage. Any DC offset
at the input to the CS4222 will be removed by the internal high-pass filters (see Figure 6 for the differential
input signal description). The ADC outputs in the CS4222 may be muted (set to zero) by writing the ADMR
and ADML bits, and can be independently powered down using the PDAD bit. ADMR, ADML, and PDAD
are all located in the ADC control byte (#1).
14
DS236F1
CS4222
Figure 5. Optional Line Input Buffer
CS4222
(2.3 + 1.4)V
2.3V
AIN+/AOUT+
(2.3 - 1.4)V
(2.3 + 1.4)V
AIN +/AOUT-
2.3V
(2.3 - 1.4)V
Full Scale Input level = (AIN+) - (AIN-)= 5.66 Vpp
Full Scale O utput level = (AOUT+) - (AOUT-)= 5.66 Vpp
Figure 6. Full Scale Input/Output Voltage
DS236F1
15
CS4222
4.2.2 Input Level Monitoring
The CS4222 includes independent Peak Input Level Monitoring for each channel. The analog-to-digital converter (ADC) continually monitors the peak digital signal for both channels, prior to the digital limiter, and
records these values in the LVL2-0 (left channel) and LVR2-0 (right channel) bits in the Converter Status
Report Byte (#6). These bits indicate whether the input level is clipping, -1 to -6 dB from full scale in 1 dB
resolution, or below -6 dB from full scale. The LVL/LVR bits are "sticky" bits and are reset to zero when the
DSP Port Mode Byte (#5) is read.
4.2.3 High Pass Filter
The operational amplifiers in the input circuitry driving the CS4222 may generate a small DC offset into the
A/D converter. The CS4222 includes a high pass filter after the decimator to remove any DC offset which
could result in recording a DC level, possibly yielding "clicks" when switching between devices in a multichannel system. The characteristics of this first-order high pass filter are outlined below for Fs equal to
48 kHz. The filter response scales linearly with sample rate. The high pass filter in the CS4222 may be defeated independently for the left and right channels by writing HPDR and HPDL in the ADC control byte (#1).
Table 2. High Pass Filter Characteristics
Frequency Response
-3 dB @ 3.7 Hz
-0.1 dB @ 20 Hz
Phase Deviation
10 degrees @ 20 Hz
Passband Ripple
None
4.3 Analog Outputs
4.3.1 Line Level Outputs
The CS4222 contains an on-chip buffer amplifier producing differential outputs capable of driving 10 kΩ
loads. Each output (AOUTL+, AOUTL-, AOUTR+, AOUTR-) will produce a nominal 2.83 Vpp (1 Vrms) output with a 2.3 volt common mode for a full scale digital input. This is equivalent to a 5.66 Vpp (2 Vrms) differential signal as shown in Figure 6. The recommended off-chip analog filter is either a 2nd order
Butterworth or a 3rd order Butterworth, if greater out-of-band noise filtering is desired. The CS4222 DAC
interpolation filter has been pre-compensated for an external 2nd order Butterworth filter with a 3 dB corner
at Fs, or a 3rd order Butterworth filter with a 3 dB corner at 0.75 Fs to provide a flat frequency response and
linear phase over the passband (see Figure 7 for Fs = 48 kHz). If the recommended filter is not used, small
frequency response magnitude and phase errors will occur. In addition to providing out-of-band noise attenuation, the output filters shown in Figure 7 provide differential to single-ended conversion.
16
DS236F1
CS4222
Figure 7. 2- and 3-Pole Butterworth Filters
DS236F1
17
CS4222
4.3.2 Analog/Digital Volume Control (Control Port Mode only)
The DAC outputs are each routed through an attenuator which is adjustable in 0.5 dB steps. Output attenuation is available through the Output Attenuator Data Bytes (#3 & #4). Level changes are implemented with
an analog volume control until the residual output noise is equal to the noise floor in the mute state at which
point volume changes are performed digitally. This technique is superior to purely digital volume control
techniques as the noise is attenuated by the same amount as the signal, thus preserving dynamic range
(see Figure 8).
The CS4222 implements a "soft" volume control whereby level changes are achieved by ramping from the
current level to the new level in 0.5 dB steps. The default rate of volume change is 8 LRCK cycles for each
0.5 dB step (equivalent to 647 µs at Fs = 48 kHz). The rate of volume change is adjustable to 4, 16, or 32
LRCK cycles with the RMP1/0 bits in the DAC control byte (#2).
"Soft" volume control may be disabled through the SOFT bit in the DAC bit Control Byte (#2). When "soft"
volume control is defeated, level changes step from the current level to the new level in a single step. The
volume change takes effect on a zero crossing to minimize audible artifacts. If there is no zero crossing,
then the requested level change will occur after a time-out period between 512 and 1024 sample periods
(10.7 ms to 21.3 ms at 48 kHz sample rate). There is a separate zero crossing detector for each channel.
ACCR and ACCL bits in the Converter Status Report Byte (#6) give feedback when a volume control change
has taken effect for the right and left channel. This bit goes high when a new setting is loaded and returns
low when it has taken effect.
Analog Digital
0
Amplitude (dB)
Signal
Noise
0
Attenuation (dB)
-113.5
Figure 8. Hybrid Analog/Digital Attenuation
4.3.3 Soft Mute/Mute on Zero Input Data
Muting is achieved by hardware or software control. Soft mute can be achieved by lowering the SMUTE pin
at which point the output level will ramp down in 0.5 dB steps to a muted state. Upon returning the SMUTE
pin high, the output will ramp up to the volume control setting in the Output Attenuator Data Bytes (#3 & #4).
“Soft” mute may be disabled through the SOFT bit in the DAC Control Byte (#2). When “soft” mute is defeated, muting occurs on zero crossings or after a time-out period, similar to the volume control changes.
Under software control, each output can be independently muted via mute control bits, MUTR and MUTL,
in the DAC Control Byte (#2). Soft mute or zero crossing mute will be implemented depending on the state
of the SOFT bit in the DAC Control Byte (#2).
Muting on consecutive zero input data is also provided where all DAC outputs will mute if they receive between 512 and 1024 consecutive zeros (or -1 code). Detection and muting is done independently for left and
right channels. A single non-zero value will immediately unmute the DAC output. This feature is disabled on
power-up, and it may be enabled with the MUTC bit in the DAC Control Byte (#2).
18
DS236F1
CS4222
4.4 Master Clock Generation
The Master Clock, MCLK, is used to operate the digital filters and the delta-sigma modulator. MCLK must be
either 256x, 384x, or 512x the desired Input Sample Rate, Fs. Fs is the frequency at which digital audio samples
for each channel are input to the DAC or output from the ADC and is equal to the LRCK frequency. The MCLK
to LRCK frequency ratio is detected automatically during the initialization sequence by counting the number of
MCLK transitions during a single LRCK period. Internal dividers are then set to generate the proper clocks for
the digital filters, delta-sigma modulators and switched-capacitor filter. Table 3 illustrates the standard audio
sample rates and the required MCLK frequencies. If MCLK stops for 10 µs, the CS4222 will enter a power down
state until the clock returns. The control port registers will maintain their current settings. It is required to have
SCLK and LRCK derived from the master clock.
Table 3. Common Clock Frequencies
Fs
(kHz)
MCLK (MHz)
256x
384x
512x
32
8.1920
12.2880
16.3840
44.1
11.2896
16.9344
22.5792
48
12.2880
18.4320
24.5760
4.4.1 MCLK Timing Constraint
The rising edge of LRCK must be less than 5 ns or greater than 15 ns after the rising edge of MCLK. This
timing constraint can be met by synchronizing the LRCK with either the rising or falling edge of MCLK.
4.5 Serial Audio Data Interface
4.5.1 Serial Audio Interface Signals
The serial interface clock, SCLK, is used for transmitting and receiving audio data. The active edge of SCLK
is chosen by setting the DSCK bit in the DSP Port Mode Byte (#6). The default on power up is that data is
valid on the rising edge for both input and output. SCLK is an input from an external source and at least
20 SCLK's per half period of LRCK are required for proper operation.
The Left/Right clock (LRCK) is used to indicate left and right data and the start of a new sample period. The
frequency of LRCK must be equal to the system sample rate, Fs.
SDIN is the data input pin which drives a pair of DACs. SDOUT is the output data pin from the ADCs.
4.5.2 Serial Audio Interface Formats
The serial audio port supports 5 input and 2 output formats, shown in Figures 9 and 10. These interface
formats are chosen via the DIF0/DIF1 pins. With the CS4222, these formats are chosen through the DSP
Port Mode Byte (#5) with the DDO and DDI2/1/0 bits. The data output format is 20 bits and may be left justified or I2S compatible depending on the state of the DDO bit. The input data format is set with the DDI bits
to be left or right justified or I2S compatible. In addition, the polarity of the SCLK edge used to clock in/out
data from the CS4222 may be set via the DSCK bit in the DSP Port Mode Byte (#5). The default input and
output format for the CS4222 is I2S compatible.
DS236F1
19
CS4222
FO R MAT 0:
(Stand-Alone and
Conntrol Port Mode)
Left
LRCK
SCLK
MSB
SDIN
FO R MAT 1:
( Conntrol Port M ode
only)
LRCK
Form at 2: M = 20
Form at 3: M = 18
Format 4: M = 16
LSB
MS B
Left
LSB
Rig ht
SCLK
SDIN
FO R M AT 2, 3, 4:
Rig ht
MSB
LSB
LRCK
MSB
LSB
Left
MSB
Right
SCLK
SDIN
LSB
MS B
( Conntrol Port Mode only)
LSB
MS B
M SC LK s
LS B
M SCLK s
Note: SCLK shown for DS CK = 0. SCLK inverted for DSCK = 1.
Figure 9. Audio DSP Data Input Formats.
FO R MAT 0:
(Stand-Alone and
Conntrol Port Mode)
LRCK
Left
SCLK
MSB
SDOUT
FO R MAT 1:
( Conntrol Port Mode
only)
Right
LRCK
LSB
MS B
Left
LSB
Right
SCLK
SDOUT
MSB
LSB
MSB
LSB
MSB
Note: SCLK shown for DSCK = 0. SCLK inverted for DSCK = 1.
Figure 10. Audio DSP Data Output Formats.
20
DS236F1
CS4222
4.6 Control Port Interface
The control port is used to load all the internal settings. The operation of the control port may be completely
asynchronous with the audio sample rate. However, to avoid potential interference problems, the control port
pins should remain static if no operation is required.
The control port has 2 modes: SPI and I2C, with the CS4222 operating as a slave device. If I2C operation is
desired, AD0/CS should be tied to VD or DGND. If the CS4222 ever detects a negative transition on AD0/CS
after power-up, SPI mode will be selected.
4.6.1 SPI Mode
In SPI mode, CS is the CS4222 chip select signal, CCLK is the control port bit clock, CDIN is the input data
line from the microcontroller and the chip address is 0010000. All signals are inputs and data is clocked in
on the rising edge of CCLK.
Figure 11 shows the operation of the control port in SPI mode. To write to a register, bring CS low. The first
7 bits on CDIN form the chip address, and must be 0010000. The eighth bit is a read/write indicator (R/W),
which must be low to write. Register reading from the CS4222 is not supported in the SPI mode. The next
8 bits form the Memory Address Pointer (MAP), which is set to the address of the register that is to be updated. The next 8 bits are the data which will be placed into a register designated by the MAP.
The CS4222 has a MAP auto increment capability, enabled by the INCR bit in the MAP register. If INCR is
a zero, then the MAP will stay constant for successive writes. If INCR is set to a 1, then MAP will auto increment after each byte is written, allowing block writes of successive registers. Register reading from the
CS4222 is not supported in the SPI mode.
CS
CCLK
CHIP
ADDRESS
CDIN
0010000
MAP
R/W
DATA
MSB
byte 1
00000000
LSB 00000000
00000000
00000000
byte n
MAP = Memory Address Pointer
Figure 11. Control Port Timing, SPI mode
DS236F1
21
CS4222
4.6.2 I2C Mode
In I2C mode, SDA is a bidirectional data line. Data is clocked into and out of the part by the clock, SCL, with
the clock-to-data relationship as shown in Figure 12. There is no CS pin. Pin AD0 forms the partial chip address and should be tied to VD or DGND as desired. The upper 6 bits of the 7 bit address field must be
001000. In order to communicate with the CS4222, the LSB of the chip address field (first byte sent to the
CS4222) should match the setting of the AD0 pin. The eighth bit of the address byte is the R/W bit (high for
a read, low for a write). If the operation is a write, the next byte is the Memory Address Pointer which selects
the register to be read or written. If the operation is a read, the contents of the register pointed to by the
Memory Address Pointer will be output. Setting the auto increment bit in MAP allows successive reads or
writes of consecutive registers. Each byte is separated by an acknowledge bit.
SDA
001000
ADDR
AD0
R/W
ACK
DATA 1-8
ACK
DATA 1-8
ACK
SCL
Start
Stop
Figure 12. Control Port Timing, I2C mode
4.6.3 Control Port Bit Definitions
All registers can be written and read in I2C mode, except the Converter Status Report Byte (#6) and the
CLKE and CALP bits in the ADC control byte (#1) which are read only. SPI mode only allows for register
writing (see the following bit definition tables for bit assignment information).
4.7 De-Emphasis
The CS4222 is capable of digital de-emphasis for 32, 44.1, or 48 kHz sample rates. Implementation of digital
de-emphasis requires reconfiguration of the digital filter to maintain the filter response at multiple sample rates
(see Figure 13).
De-emphasis control is achieved with the DEM1/0 pins or through the DEM2-0 bits in the DSP Port Mode Byte
(#2). The default state on power-up is de-emphasis controlled via the DEM1/0 pins (DEM2-0 bits=0). DEM1/0
pin control is defined in Table 4.
Gain
dB
Table 4. De-Emphasis filter control
T1 = 50 µs
DEM 1
DEM 0
De-emphasis
0
0
32 kHz
0
1
44.1 kHz
1
0
48 kHz
1
1
OFF
0 dB
T2 = 15 µs
-10 dB
F1
F2
Frequency
Figure 13. De-emphasis Curve.
22
DS236F1
CS4222
4.8 Power-up / Reset / Power Down / Calibration
Upon power up, the user should hold RST = 0 for approximately 10 ms. In this state, the control port is reset to
its default settings and the part remains in the power down mode. At the end of RST, the device performs an
offset calibration which lasts approximately 50 ms after which the device enters normal operation. A calibration
may also be initiated via the CAL bit in the ADC Control Byte (#1). The CALP bit in the ADC Control Byte is a
read only bit indicating the status of the calibration.
Reset/Power Down is achieved by lowering the RST pin causing the part to enter power down. Once RST goes
high, the control port is functional and the desired settings should be loaded.
The CS4222 will also enter power down mode if the master clock source stops for approximately 10 µs or if the
LRCK is not synchronous to the master clock. The control port will retain its current settings.
Additionally, the PDAD (ADC Control Byte #1) and PDDA (DAC Control Byte #2) bits can be used to power down
the ADC’s and DAC’s independently. If both are set to 1, the CS4222 will power down the entire chip. The control
port will retain its current settings.
The CS4222 will mute the analog outputs and enter the power down mode if the supply drops below
approximately 4 volts.
4.9 Power Supply, Layout and Grounding
As with any high resolution converter, the CS4222 requires careful attention to power supply and grounding
arrangements to optimize performance. The Typical Connection Diagram shows the recommended power
arrangement with VA, and VD connected to clean supplies. Decoupling capacitors should be located as close
to the device package as possible. If desired, all supply pins may be connected to the same supply, but the
recommended decoupling capacitors should still be placed on each supply pin. The AGND and DGND pins
should be tied together with solid ground plane fill underneath the converter extending out to the GND side of
the decoupling caps for VA, and VD. This recommended layout can be seen in the CDB4222 evaluation board
and data sheet.
DS236F1
23
CS4222
4.10 ADC and DAC Filter Response Plots
Figures 14 through 19 show the overall frequency response, passband ripple and transition band for the CS4222
ADCs and DACs.
24
Figure 14. ADC Filter Response
Figure 15. ADC Passband Ripplee
Figure 16. ADC Transition Band
Figure 17. DAC Filter Response
Figure 18. DAC Passband Ripple
Figure 19. DAC Transition Band
DS236F1
CS4222
5. REGISTER DESCRIPTIONS
Memory Address Pointer (MAP)
B7
INCR
B6
0
B5
0
MAP2-MAP0
Register Pointer
INCR
Auto Increment Control Bit
0 - No auto increment
1 - Auto increment on
B4
0
B3
0
B2
MAP2
B1
MAP1
B0
MAP0
B1
CALP
B0
CLKE
This register defaults to 00h.
Reserved Byte (0)
This byte is reserved for internal use and must be set to 00h for normal operation.
This register defaults to 00h.
ADC Control Byte (1)
B7
PDAD
B6
HPDR
B5
HPDL
B4
ADMR
PDAD
Power Down
0 - Normal
1 - Power Down
HPDR-HPDL
High pass filter defeat, right and left
0 - High pass filters active
1 - High pass filters defeated
ADMR-ADML
ADC Muting, right and left
0 - Normal
1 - Output muted
CAL
Calibration control bit
0 - Normal operation
1 - Rising edge initiates calibration
B3
ADML
B2
CAL
The following bits are read only:
CALP
Calibration status
0 - Calibration done
1 - Calibration in progress
CLKE
Clocking Error
0 - No error
1 - error
This register defaults to 00h.
DS236F1
25
CS4222
DAC Control Byte (2)
B7
PDDA
B6
MUTC
B5
MUTR
B4
MUTL
B3
SOFT
B2
0
B1
RMP1
PDDA
Powers down DAC
0 - Normal.
1 - Power down
MUTC
Controls mute on consecutive zeros function
0 - 512 consecutive zeros will mute DAC
1 - DAC output will not mute on zeros.
MUTR-MUTL
Mute control bits
0 - Normal output level
1 - Selected DAC output muted
SOFT
Soft Mute Control
0 - Volume control changes, muting and mute-on-zeros occur with "ramp"
1 - Volume control changes, muting and mute-on-zeros occur on zero crossings
RMP1-0
Soft Volume 0.5 dB step rate
0 - 1 step per 8 LRCK's
1 - 1 step per 4 LRCK's
2 - 1 step per 16 LRCK's
3 - 1 step per 32 LRCK's
B0
RMP0
This register defaults to 00h.
Output Attenuator Data Byte (3, 4)
B7
ATT7
ATT7-ATT0
B6
ATT6
B5
ATT5
B4
ATT4
B3
ATT3
B2
ATT2
B1
ATT1
B0
ATT0
Sets attenuator level
0 - No attenuation
227 - 113.5 dB attenuation
>227 - DAC muted
ATT0 represents 0.5 dB of attenuation
This register defaults to 00h.
26
DS236F1
CS4222
DSP Port Mode Byte (5)
B7
DEM2
DEM2-0
B6
DEM1
B5
DEM0
B4
DSCK
B3
DDO
B2
DDF2
B1
DDF1
B0
DDF0
B1
LVL2
B0
LVL0
Selects de-emphasis control source
0 - De-emphasis controlled by pins
1 - 44.1 kHz de-emphasis setting
2 - 48 kHz de-emphasis setting
3 - 32 kHz de-emphasis setting
4 - De-emphasis disabled
5, 6, 7 - Not used
DSCK
Sets the polarity of clocking data for both input and output
0 - Data valid on rising edge of SCLK
1 - Data valid on falling edge of SCLK
DDO
Data output format
0 - I2S compatible
1 - Left justified
DDI2-DDI0
Data input format
0 - I2S compatible
1 - Left justified
2 - Right justified, 20-bit
3 - Right justified, 18-bit
4 - Right justified, 16-bit
5, 6, 7 - Not used
This register defaults to 00h.
Converter Status Report Byte (Read Only) (6)
B7
ACCR
B6
ACCL
B5
LVR2
B4
LVR1
ACCR-ACCL
Acceptance bit
0 - ATT7-0 has been accepted
1 - New setting waiting for zero crossing
LVL2-0,LVR2-0
Left and Right ADC output level
0 - Normal output levels
1 - -6 dB level
2 - -5 dB level
3 - -4 dB level
4 - -3 dB level
5 - -2 dB level
6 - -1 dB level
7 - Clipping
B3
LVR0
B2
LVL2
LVL2-0 and LVR2-0 bits are 'sticky'. They constantly monitor the ADC output for the peak levels and hold the maximum output. They are reset to 0 when the DSP Port Mode Byte (5) is read.
This register is read only.
DS236F1
27
CS4222
6. PARAMETER DEFINITIONS
Dynamic Range
The ratio of the full scale rms value of the signal to the rms sum of all other spectral components over the
specified bandwidth. Dynamic range is a signal-to-noise measurement over the specified bandwidth
made with a -60 dBFS signal. 60 dB is then added to the resulting measurement to refer the measurement
to full scale. This technique ensures that the distortion components are below the noise level and do not
affect the measurement. This measurement technique has been accepted by the Audio Engineering Society, AES17-1991, and the Electronic Industries Association of Japan, EIAJ CP-307.
Total Harmonic Distortion + Noise (THD+N)
The ratio of the rms value of the signal to the rms sum of all other spectral components over the specified
bandwidth (typically 20 Hz to 20 kHz), including distortion components. Expressed in decibels. ADCs are
measured at -1 dBFS as suggested in AES17-1991 Annex A and DACs are measured at 0 dBFS.
Idle Channel Noise / Signal-to-Noise-Ratio
The ratio of the rms analog output level with 1 kHz full scale digital input to the rms analog output level
with all zeros into the digital input. Measured A-weighted over a 10 Hz to 20 kHz bandwidth. Units in decibels. This specification has been standardized by the Audio Engineering Society, AES17-1991, and referred to as Idle Channel Noise. This specification has also been standardized by the Electronic Industries
Association of Japan, EIAJ CP-307, and referred to as Signal-to-Noise-Ratio.
Total Harmonic Distortion (THD)
THD is the ratio of the test signal amplitude to the rms sum of all the in-band harmonics of the test signal.
Units in decibels.
Interchannel Isolation
A measure of crosstalk between channels. Measured for each channel at the converter's output with no
signal to the input under test and a full-scale signal applied to the other channel. Units in decibels.
Frequency Response
A measure of the amplitude response variation from 20 Hz to 20 kHz relative to the amplitude response
at 1 kHz. Units in decibels.
Interchannel Gain Mismatch
For the ADCs, the difference in input voltage that generates the full scale code for each channel. For the
DACs, the difference in output voltages for each channel with a full scale digital input. Units are in decibels.
Gain Error
The deviation from the nominal full scale output for a full scale input.
Gain Drift
The change in gain value with temperature. Units in ppm/°C.
Offset Error
For the ADCs, the deviation in LSB's of the output from mid-scale with the selected inputs tied to a common potential. For the DAC's, the differential output voltage with mid-scale input code. Units are in volts.
28
DS236F1
CS4222
7. PACKAGE DIMENSIONS
28L SSOP PACKAGE DRAWING
N
D
E11
A2
E
e
b
2
A1
A
∝
L
END VIEW
SEATING
PLANE
SIDE VIEW
1 2 3
TOP VIEW
INCHES
DIM
A
A1
A2
b
D
E
E1
e
L
∝
MIN
-0.002
0.064
0.009
0.390
0.291
0.197
0.024
0.025
0°
MAX
0.084
0.010
0.074
0.015
0.413
0.323
0.220
0.027
0.040
8°
MILLIMETERS
MIN
MAX
-2.13
0.05
0.25
1.62
1.88
0.22
0.38
9.90
10.50
7.40
8.20
5.00
5.60
0.61
0.69
0.63
1.03
0°
8°
NOTE
15,16
14
14
Notes: 14. “D” and “E1” are reference datums and do not include mold flash or protrusions, but do include mold
mismatch and are measured at the parting line. Mold flash or protrusions shall not exceed 0.20 mm per
side.
15. Dimension “b” does not include dambar protrusion/intrusion. Allowable dambar protrusion shall be
0.13 mm total in excess of “b” dimension at maximum material condition. Dambar intrusion shall not
reduce dimension “b” by more than 0.07 mm at least material condition.
16. These dimensions apply to the flat section of the lead between 0.10 and 0.25 mm from lead tips.
DS236F1
29
Similar pages