82C55A Semiconductor CMOS Programmable Peripheral Interface June 1998 Features Description • Pin Compatible with NMOS 8255A The Harris 82C55A is a high performance CMOS version of the industry standard 8255A and is manufactured using a self-aligned silicon gate CMOS process (Scaled SAJI IV). It is a general purpose programmable I/O device which may be used with many different microprocessors. There are 24 I/O pins which may be individually programmed in 2 groups of 12 and used in 3 major modes of operation. The high performance and industry standard configuration of the 82C55A make it compatible with the 80C86, 80C88 and other microprocessors. • 24 Programmable I/O Pins • Fully TTL Compatible • High Speed, No “Wait State” Operation with 5MHz and 8MHz 80C86 and 80C88 • Direct Bit Set/Reset Capability • Enhanced Control Word Read Capability • L7 Process Static CMOS circuit design insures low operating power. TTL compatibility over the full military temperature range and bus hold circuitry eliminate the need for pull-up resistors. The Harris advanced SAJI process results in performance equal to or greater than existing functionally equivalent products at a fraction of the power. • 2.5mA Drive Capability on All I/O Ports • Low Standby Power (ICCSB) . . . . . . . . . . . . . . . . .10µA Ordering Information PART NUMBERS 5MHz 8MHz CP82C55A-5 CP82C55A IP82C55A-5 IP82C55A CS82C55A-5 CS82C55A IS82C55A-5 IS82C55A CD82C55A-5 CD82C55A ID82C55A-5 ID82C55A PACKAGE 40 Ld PDIP 44 Ld PLCC MD82C55A-5/B MD82C55A/B 8406601QA 8406602QA 40 Ld CERDIP 8406602XA PKG. NO. 0oC to 70oC E40.6 -40oC to 85oC E40.6 0oC to 70oC N44.65 -40oC to 85oC N44.65 0oC to 70oC F40.6 -40oC to 85oC F40.6 -55oC to 125oC F40.6 SMD# 44 Pad MR82C55A-5/B MR82C55A/B CLCC 8406601XA TEMPERATURE RANGE F40.6 -55oC to 125oC J44.A SMD# J44.A Pinouts RD PA0 PA1 PA2 PA3 NC PA4 PA5 PA6 PA7 WR 37 D0 36 D1 35 D2 34 D3 33 D4 32 D5 31 D6 30 D7 29 NC 6 5 4 3 2 1 44 43 42 41 40 CS GND A1 A0 PC7 NC PC6 PC5 PC4 PC0 PC1 7 8 9 10 11 12 13 14 15 16 17 39 38 37 36 35 34 33 32 31 30 29 18 1920 21 22 23 24 25 26 27 28 CAUTION: These devices are sensitive to electrostatic discharge. Users should follow proper IC Handling Procedures. Copyright © Harris Corporation 1998 1 RESET D0 D1 D2 D3 NC D4 D5 D6 D7 VCC PB2 NC PB3 PB4 PB5 PB6 PB7 39 NC 38 RESET PC2 PC3 PB0 PB1 PA7 PA6 PA5 PA4 PA3 PA2 PA1 PA0 CS WR NC VCC PB7 PB6 PB5 PB4 PB3 PB2 13 14 15 16 17 18 19 20 31 30 29 28 27 26 25 24 23 22 21 82C55A (PLCC) TOP VIEW PA4 6 5 4 3 2 1 44 43 42 41 40 PA5 PA6 7 GND PA7 NC 8 WR A1 9 RESET A0 10 D0 PC7 11 D1 PC6 12 D2 PC5 13 D3 PC4 14 D4 PC0 15 D5 PC1 16 D6 PC2 17 D7 18 19 20 21 22 23 24 25 26 27 28 VCC PB7 PB6 PB5 PB4 PB3 PB1 5 6 7 8 9 10 11 12 40 39 38 37 36 35 34 33 32 PB0 1 2 3 4 PC3 PA3 PA2 PA1 PA0 RD CS GND A1 A0 PC7 PC6 PC5 PC4 PC0 PC1 PC2 PC3 PB0 PB1 PB2 82C55A (CLCC) TOP VIEW RD 82C55A (DIP) TOP VIEW File Number 2969.2 82C55A Pin Description SYMBOL PIN NUMBER VCC 26 VCC: The +5V power supply pin. A 0.1µF capacitor between pins 26 and 7 is recommended for decoupling. GND 7 GROUND D0-D7 27-34 I/O RESET 35 I RESET: A high on this input clears the control register and all ports (A, B, C) are set to the input mode with the “Bus Hold” circuitry turned on. CS 6 I CHIP SELECT: Chip select is an active low input used to enable the 82C55A onto the Data Bus for CPU communications. RD 5 I READ: Read is an active low input control signal used by the CPU to read status information or data via the data bus. WR 36 I WRITE: Write is an active low input control signal used by the CPU to load control words and data into the 82C55A. A0-A1 8, 9 I ADDRESS: These input signals, in conjunction with the RD and WR inputs, control the selection of one of the three ports or the control word register. A0 and A1 are normally connected to the least significant bits of the Address Bus A0, A1. PA0-PA7 1-4, 37-40 I/O PORT A: 8-bit input and output port. Both bus hold high and bus hold low circuitry are present on this port. PB0-PB7 18-25 I/O PORT B: 8-bit input and output port. Bus hold high circuitry is present on this port. PC0-PC7 10-17 I/O PORT C: 8-bit input and output port. Bus hold circuitry is present on this port. TYPE DESCRIPTION DATA BUS: The Data Bus lines are bidirectional three-state pins connected to the system data bus. Functional Diagram POWER SUPPLIES +5V GND GROUP A PORT A (8) GROUP A CONTROL GROUP A PORT C UPPER (4) BI-DIRECTIONAL DATA BUS D7-D0 DATA BUS BUFFER 8-BIT INTERNAL DATA BUS RD WR A1 READ WRITE CONTROL LOGIC GROUP B CONTROL GROUP B PORT C LOWER (4) GROUP B PORT B (8) A0 RESET CS 2 I/O PA7-PA0 I/O PC7-PC4 I/O PC3-PC0 I/O PB7-PB0 82C55A Functional Description POWER SUPPLIES Data Bus Buffer This three-state bi-directional 8-bit buffer is used to interface the 82C55A to the system data bus. Data is transmitted or received by the buffer upon execution of input or output instructions by the CPU. Control words and status information are also transferred through the data bus buffer. +5V GND BI-DIRECTIONAL DATA BUS DATA BUS D7-D0 BUFFER Read/Write and Control Logic The function of this block is to manage all of the internal and external transfers of both Data and Control or Status words. It accepts inputs from the CPU Address and Control busses and in turn, issues commands to both of the Control Groups. RD WR A1 A0 RESET READ WRITE CONTROL LOGIC GROUP A CONTROL GROUP A PORT A (8) GROUP A PORT C UPPER (4) 8-BIT INTERNAL DATA BUS GROUP B CONTROL GROUP B PORT C LOWER (4) GROUP B PORT B (8) I/O PA7PA0 I/O PC7PC4 I/O PC3PC0 I/O PB7PB0 (CS) Chip Select. A “low” on this input pin enables the communcation between the 82C55A and the CPU. CS (RD) Read. A “low” on this input pin enables 82C55A to send the data or status information to the CPU on the data bus. In essence, it allows the CPU to “read from” the 82C55A. FIGURE 1. 82C55A BLOCK DIAGRAM. DATA BUS BUFFER, READ/WRITE, GROUP A & B CONTROL LOGIC FUNCTIONS (WR) Write. A “low” on this input pin enables the CPU to write data or control words into the 82C55A. (RESET) Reset. A “high” on this input initializes the control register to 9Bh and all ports (A, B, C) are set to the input mode. “Bus hold” devices internal to the 82C55A will hold the I/O port inputs to a logic “1” state with a maximum hold current of 400µA. (A0 and A1) Port Select 0 and Port Select 1. These input signals, in conjunction with the RD and WR inputs, control the selection of one of the three ports or the control word register. They are normally connected to the least significant bits of the address bus (A0 and A1). Group A and Group B Controls 82C55A BASIC OPERATION A1 A0 RD WR CS 0 0 0 1 0 The functional configuration of each port is programmed by the systems software. In essence, the CPU “outputs” a control word to the 82C55A. The control word contains information such as “mode”, “bit set”, “bit reset”, etc., that initializes the functional configuration of the 82C55A. INPUT OPERATION (READ) Port A → Data Bus 0 1 0 1 0 Port B → Data Bus 1 0 0 1 0 Port C → Data Bus 1 1 0 1 0 Control Word → Data Bus Each of the Control blocks (Group A and Group B) accepts “commands” from the Read/Write Control logic, receives “control words” from the internal data bus and issues the proper commands to its associated ports. Control Group A - Port A and Port C upper (C7 - C4) Control Group B - Port B and Port C lower (C3 - C0) OUTPUT OPERATION (WRITE) 0 0 1 0 0 Data Bus → Port A 0 1 1 0 0 Data Bus → Port B 1 0 1 0 0 Data Bus → Port C 1 1 1 0 0 Data Bus → Control The control word register can be both written and read as shown in the “Basic Operation” table. Figure 4 shows the control word format for both Read and Write operations. When the control word is read, bit D7 will always be a logic “1”, as this implies control word mode information. DISABLE FUNCTION X X X X 1 Data Bus → Three-State X X 1 1 0 Data Bus → Three-State 3 82C55A register will contain 9Bh. During the execution of the system program, any of the other modes may be selected using a single output instruction. This allows a single 82C55A to service a variety of peripheral devices with a simple software maintenance routine. Any port programmed as an output port is initialized to all zeros when the control word is written. Ports A, B, and C The 82C55A contains three 8-bit ports (A, B, and C). All can be configured to a wide variety of functional characteristics by the system software but each has its own special features or “personality” to further enhance the power and flexibility of the 82C55A. ADDRESS BUS Port A One 8-bit data output latch/buffer and one 8-bit data input latch. Both “pull-up” and “pull-down” bus-hold devices are present on Port A. See Figure 2A. CONTROL BUS DATA BUS Port B One 8-bit data input/output latch/buffer and one 8-bit data input buffer. See Figure 2B. Port C One 8-bit data output latch/buffer and one 8-bit data input buffer (no latch for input). This port can be divided into two 4-bit ports under the mode control. Each 4-bit port contains a 4-bit latch and it can be used for the control signal output and status signal inputs in conjunction with ports A and B. See Figure 2B. C B 8 A I/O PB7-PB0 INPUT MODE MODE 1 MODE 2 OUTPUT MODE VCC I/O 8 I/O PA7-PA0 A I/O 8 CONTROL CONTROL OR I/O OR I/O C I/O PA7-PA0 A BIDIRECTIONAL I/O PB7-PB0 P 4 PC7-PC4 PC3-PC0 B 8 FIGURE 2A. PORT A BUS-HOLD CONFIGURATION I/O C PB7-PB0 INTERNAL DATA OUT (LATCHED) 4 B 8 EXTERNAL PORT A PIN RESET OR MODE CHANGE A0-A1 CS 82C55A MODE 0 MASTER RESET OR MODE CHANGE INTERNAL DATA IN D7-D0 RD, WR CONTROL PA7-PA0 FIGURE 3. BASIC MODE DEFINITIONS AND BUS INTERFACE CONTROL WORD INTERNAL DATA IN D7 D6 D5 D4 D3 D2 D1 D0 EXTERNAL PORT B, C PIN INTERNAL DATA OUT (LATCHED) GROUP B PORT C (LOWER) 1 = INPUT 0 = OUTPUT OUTPUT MODE PORT B 1 = INPUT 0 = OUTPUT FIGURE 2B. PORT B AND C BUS-HOLD CONFIGURATION MODE SELECTION 0 = MODE 0 1 = MODE 1 FIGURE 2. BUS-HOLD CONFIGURATION Operational Description GROUP A Mode Selection PORT C (UPPER) 1 = INPUT 0 = OUTPUT There are three basic modes of operation than can be selected by the system software: Mode 0 - Basic Input/Output Mode 1 - Strobed Input/Output Mode 2 - Bi-directional Bus PORT A 1 = INPUT 0 = OUTPUT MODE SELECTION 00 = MODE 0 01 = MODE 1 1X = MODE 2 When the reset input goes “high”, all ports will be set to the input mode with all 24 port lines held at a logic “one” level by internal bus hold devices. After the reset is removed, the 82C55A can remain in the input mode with no additional initialization required. This eliminates the need to pullup or pulldown resistors in all-CMOS designs. The control word MODE SET FLAG 1 = ACTIVE FIGURE 4. MODE DEFINITION FORMAT 4 82C55A The modes for Port A and Port B can be separately defined, while Port C is divided into two portions as required by the Port A and Port B definitions. All of the output registers, including the status flip-flops, will be reset whenever the mode is changed. Modes may be combined so that their functional definition can be “tailored” to almost any I/O structure. For instance: Group B can be programmed in Mode 0 to monitor simple switch closings or display computational results, Group A could be programmed in Mode 1 to monitor a keyboard or tape reader on an interrupt-driven basis. This function allows the programmer to enable or disable a CPU interrupt by a specific I/O device without affecting any other device in the interrupt structure. The mode definitions and possible mode combinations may seem confusing at first, but after a cursory review of the complete device operation a simple, logical I/O approach will surface. The design of the 82C55A has taken into account things such as efficient PC board layout, control signal definition vs. PC layout and complete functional flexibility to support almost any peripheral device with no external logic. Such design represents the maximum use of the available pins. Operating Modes INTE Flip-Flop Definition (BIT-SET)-INTE is SET - Interrupt Enable (BIT-RESET)-INTE is Reset - Interrupt Disable NOTE: All Mask flip-flops are automatically reset during mode selection and device Reset. Mode 0 (Basic Input/Output). This functional configuration provides simple input and output operations for each of the three ports. No handshaking is required, data is simply written to or read from a specific port. Mode 0 Basic Functional Definitions: • Two 8-bit ports and two 4-bit ports • Any Port can be input or output Single Bit Set/Reset Feature (Figure 5) • Outputs are latched Any of the eight bits of Port C can be Set or Reset using a single Output instruction. This feature reduces software requirements in control-based applications. • Input are not latched • 16 different Input/Output configurations possible When Port C is being used as status/control for Port A or B, these bits can be set or reset by using the Bit Set/Reset operation just as if they were output ports. MODE 0 PORT DEFINITION A CONTROL WORD D7 D6 D5 D4 D3 D2 D1 D0 X X X DON’T CARE BIT SET/RESET 1 = SET 0 = RESET BIT SELECT 0 1 2 3 4 0 1 0 1 0 0 0 1 1 0 0 0 0 0 1 5 1 0 1 6 0 1 1 7 1 B0 1 B1 1 B2 BIT SET/RESET FLAG 0 = ACTIVE FIGURE 5. BIT SET/RESET FORMAT Interrupt Control Functions When the 82C55A is programmed to operate in mode 1 or mode 2, control signals are provided that can be used as interrupt request inputs to the CPU. The interrupt request signals, generated from port C, can be inhibited or enabled by setting or resetting the associated INTE flip-flop, using the bit set/reset function of port C. 5 B GROUP A PORTC PORT A (Upper) GROUP B # PORTC PORT B (Lower) D4 D3 D1 D0 0 0 0 0 Output Output 0 Output Output 0 0 0 1 Output Output 1 Output Input 0 0 1 0 Output Output 2 Input Output 0 0 1 1 Output Output 3 Input Input 0 1 0 0 Output Input 4 Output Output 0 1 0 1 Output Input 5 Output Input 0 1 1 0 Output Input 6 Input Output 0 1 1 1 Output Input 7 Input Input 1 0 0 0 Input Output 8 Output Output 1 0 0 1 Input Output 9 Output Input 1 0 1 0 Input Output 10 Input Output 1 0 1 1 Input Output 11 Input Input 1 1 0 0 Input Input 12 Output Output 1 1 0 1 Input Input 13 Output Input 1 1 1 0 Input Input 14 Input Output 1 1 1 1 Input Input 15 Input Input 82C55A Mode 0 (Basic Input) tRR RD tIR tHR INPUT tAR tRA CS, A1, A0 D7-D0 tRD tDF Mode 0 (Basic Output) tWW WR tWD tDW D7-D0 tAW tWA CS, A1, A0 OUTPUT tWB Mode 0 Configurations CONTROL WORD #0 CONTROL WORD #2 D7 D6 D5 D4 D3 D2 D1 D0 1 0 0 0 0 0 0 D7 D6 D5 D4 D3 D2 D1 D0 0 1 8 A 82C55A 4 4 8 B 0 0 0 0 1 0 82C55A 4 PC7 - PC4 PA7 - PA0 PC7 - PC4 C D7 - D0 4 PC3 - PC0 8 PB7 - PB0 B PC3 - PC0 PB7 - PB0 CONTROL WORD #3 0 0 D7 D6 D5 D4 D3 D2 D1 D0 1 1 8 A 82C55A D7 - D0 0 8 D7 D6 D5 D4 D3 D2 D1 D0 0 0 A CONTROL WORD #1 1 0 PA7 - PA0 C D7 - D0 0 4 8 B 0 0 0 0 1 1 8 PA7 - PA0 A 82C55A 4 PC7 - PC4 C 4 0 D7 - D0 4 8 B 6 PC7 - PC4 C PC3 - PC0 PB7 - PB0 PA7 - PA0 PC3 - PC0 PB7 - PB0 82C55A Mode 0 Configurations (Continued) CONTROL WORD #4 CONTROL WORD #8 D7 D6 D5 D4 D3 D2 D1 D0 1 0 0 0 1 0 0 D7 D6 D5 D4 D3 D2 D1 D0 0 1 8 A 82C55A 4 4 8 B 0 0 1 0 0 82C55A 4 8 8 B 0 1 82C55A PB7 - PB0 0 0 0 1 82C55A 4 PC7 - PC4 PA7 - PA0 PC7 - PC4 C D7 - D0 4 PC3 - PC0 8 PB7 - PB0 B PC3 - PC0 PB7 - PB0 D7 D6 D5 D4 D3 D2 D1 D0 1 4 4 8 B 0 0 1 0 0 1 0 8 PA7 - PA0 A 82C55A 4 PC7 - PC4 PA7 - PA0 PC7 - PC4 C D7 - D0 4 PC3 - PC0 8 PB7 - PB0 B CONTROL WORD #7 PC3 - PC0 PB7 - PB0 CONTROL WORD #11 D7 D6 D5 D4 D3 D2 D1 D0 0 1 D7 D6 D5 D4 D3 D2 D1 D0 1 1 8 A 82C55A D7 - D0 1 8 C D7 - D0 1 0 A 0 8 0 PC3 - PC0 CONTROL WORD #10 A 0 0 PA7 - PA0 D7 D6 D5 D4 D3 D2 D1 D0 0 4 PB7 - PB0 CONTROL WORD #6 1 PC7 - PC4 C D7 - D0 PC3 - PC0 1 B 1 4 PA7 - PA0 D7 D6 D5 D4 D3 D2 D1 D0 4 0 0 PC7 - PC4 C D7 - D0 0 0 82C55A 1 8 0 0 CONTROL WORD #9 A 1 0 8 D7 D6 D5 D4 D3 D2 D1 D0 0 1 A CONTROL WORD #5 1 0 PA7 - PA0 C D7 - D0 0 4 8 B 0 1 0 0 1 1 8 PA7 - PA0 A 82C55A 4 PC7 - PC4 C 4 0 D7 - D0 4 8 B 7 PC7 - PC4 C PC3 - PC0 PB7 - PB0 PA7 - PA0 PC3 - PC0 PB7 - PB0 82C55A Mode 0 Configurations (Continued) CONTROL WORD #12 CONTROL WORD #14 D7 D6 D5 D4 D3 D2 D1 D0 1 0 0 1 1 0 0 D7 D6 D5 D4 D3 D2 D1 D0 0 1 8 A 82C55A 4 4 8 B 0 1 1 1 0 1 0 8 82C55A PA7 - PA0 4 PC7 - PC4 PC7 - PC4 C D7 - D0 4 PC3 - PC0 PC3 - PC0 8 PB7 - PB0 PB7 - PB0 B CONTROL WORD #15 D7 D6 D5 D4 D3 D2 D1 D0 0 1 A CONTROL WORD #13 1 0 PA7 - PA0 C D7 - D0 0 0 0 D7 D6 D5 D4 D3 D2 D1 D0 1 1 8 A 82C55A D7 - D0 4 8 B 0 1 1 0 1 1 8 PA7 - PA0 PA7 - PA0 A 82C55A 4 PC7 - PC4 C 4 0 PC7 - PC4 C D7 - D0 4 PC3 - PC0 PC3 - PC0 8 PB7 - PB0 PB7 - PB0 B Operating Modes MODE 1 (PORT A) Mode 1 - (Strobed Input/Output). This functional configuration provides a means for transferring I/O data to or from a specified port in conjunction with strobes or “hand shaking” signals. In mode 1, port A and port B use the lines on port C to generate or accept these “hand shaking” signals. CONTROL WORD D7 D6 D5 D4 D3 D2 D1 D0 1 0 1 1 1/0 INTE A PC6, PC7 1 = INPUT 0 = OUTPUT Mode 1 Basic Function Definitions: • Two Groups (Group A and Group B) • Each group contains one 8-bit port and one 4-bit control/data port • The 8-bit data port can be either input or output. Both inputs and outputs are latched. • The 4-bit port is used for control and status of the 8-bit port. 8 PA7-PA0 PC4 STBA PC5 IBFA INTRA PC3 RD PC6, PC7 2 I/O MODE 1 (PORT B) CONTROL WORD D7 D6 D5 D4 D3 D2 D1 D0 Input Control Signal Definition 1 1 1 PB7-PB0 INTE B (Figures 6 and 7) PC2 8 STBB PC1 IBFB PC0 INTRB STB (Strobe Input) A “low” on this input loads data into the input latch. RD IBF (Input Buffer Full F/F) FIGURE 6. MODE 1 INPUT A “high” on this output indicates that the data has been loaded into the input latch: in essence, and acknowledgment. IBF is set by STB input being low and is reset by the rising edge of the RD input. 8 82C55A tST STB tSIB IBF tSIT tRIB INTR tRIT RD tPH INPUT FROM PERIPHERAL tPS FIGURE 7. MODE 1 (STROBED INPUT) INTR (Interrupt Request) INTE A A “high” on this output can be used to interrupt the CPU when and input device is requesting service. INTR is set by the condition: STB is a “one”, IBF is a “one” and INTE is a “one”. It is reset by the falling edge of RD. This procedure allows an input device to request service from the CPU by simply strobing its data into the port. Controlled by Bit Set/Reset of PC6. INTE B Controlled by Bit Set/Reset of PC2. NOTE: 1. To strobe data into the peripheral device, the user must operate the strobe line in a hand shaking mode. The user needs to send OBF to the peripheral device, generates an ACK from the peripheral device and then latch data into the peripheral device on the rising edge of OBF. INTE A Controlled by bit set/reset of PC4. INTE B MODE 1 (PORT A) Controlled by bit set/reset of PC2. PA7-PA0 CONTROL WORD D7 D6 D5 D4 D3 D2 D1 D0 Output Control Signal Definition (Figure 8 and 9) 1 0 1 1 1/0 OBF - Output Buffer Full F/F). The OBF output will go “low” to indicate that the CPU has written data out to be specified port. This does not mean valid data is sent out of the part at this time since OBF can go true before data is available. Data is guaranteed valid at the rising edge of OBF, (See Note 1). The OBF F/F will be set by the rising edge of the WR input and reset by ACK input being low. PC4, PC5 1 = INPUT 0 = OUTPUT INTE A 8 PC7 OBFA PC6 ACKA INTRA PC3 WR ACK - Acknowledge Input). A “low” on this input informs the 82C55A that the data from Port A or Port B is ready to be accepted. In essence, a response from the peripheral device indicating that it is ready to accept data, (See Note 1). PC4, PC5 2 MODE 1 (PORT B) PB7-PB0 CONTROL WORD D7 D6 D5 D4 D3 D2 D1 D0 INTR - (Interrupt Request). A “high” on this output can be used to interrupt the CPU when an output device has accepted data transmitted by the CPU. INTR is set when ACK is a “one”, OBF is a “one” and INTE is a “one”. It is reset by the falling edge of WR. 1 1 PC1 OBFB PC2 ACKB PC0 INTRB 0 INTE B WR FIGURE 8. MODE 1 OUTPUT 9 8 82C55A tWOB WR tAOB OBF INTR tWIT ACK tAK tAIT OUTPUT tWB FIGURE 9. MODE 1 (STROBED OUTPUT) PA7-PA0 RD CONTROL WORD D7 D6 D5 D4 D3 D2 D1 D0 1 0 1 1 1/0 1 8 PC4 STBA PC5 IIBFA PC6, PC7 1 = INPUT 0 = OUTPUT PC6, PC7 PB7, PB0 WR WR CONTROL WORD D7 D6 D5 D4 D3 D2 D1 D0 INTRA PC3 0 PA7-PA0 2 1 0 1 0 1/0 I/O OBFB PC2 PC0 PC7 OBFA PC6 ACKA INTRA PC3 1 PC4, PC5 1 = INPUT 0 = OUTPUT 8 PC1 1 8 PC4, PC5 PB7, PB0 2 I/O 8 PC2 STBB ACKB PC1 IBFB INTRB PC0 INTRB RD PORT A - (STROBED INPUT) PORT B - (STROBED OUTPUT) PORT A - (STROBED OUTPUT) PORT B - (STROBED INPUT) Combinations of Mode 1: Port A and Port B can be individually defined as input or output in Mode 1 to support a wide variety of strobed I/O applications. FIGURE 10. COMBINATIONS OF MODE 1 Operating Modes Mode 2 (Strobed Bi-Directional Bus I/O) Output Operations The functional configuration provides a means for communicating with a peripheral device or structure on a single 8-bit bus for both transmitting and receiving data (bi-directional bus I/O). “Hand shaking” signals are provided to maintain proper bus flow discipline similar to Mode 1. Interrupt generation and enable/disable functions are also available. OBF - (Output Buffer Full). The OBF output will go “low” to indicate that the CPU has written data out to port A. Mode 2 Basic Functional Definitions: • Used in Group A only • One 8-bit, bi-directional bus Port (Port A) and a 5-bit control Port (Port C) • Both inputs and outputs are latched • The 5-bit control port (Port C) is used for control and status for the 8-bit, bi-directional bus port (Port A) INTE 1 - (The INTE flip-flop associated with OBF). Controlled by bit set/reset of PC4. ACK - (Acknowledge). A “low” on this input enables the three-state output buffer of port A to send out the data. Otherwise, the output buffer will be in the high impedance state. Input Operations STB - (Strobe Input). A “low” on this input loads data into the input latch. IBF - (Input Buffer Full F/F). A “high” on this output indicates that data has been loaded into the input latch. Bi-Directional Bus I/O Control Signal Definition INTE 2 - (The INTE flip-flop associated with IBF). Controlled by bit set/reset of PC4. (Figures 11, 12, 13, 14) INTR - (Interrupt Request). A high on this output can be used to interrupt the CPU for both input or output operations. 10 82C55A CONTROL WORD D7 D6 D5 D4 D3 D2 D1 D0 1 1 INTRA PC3 1/0 1/0 1/0 PA7-PA0 PC2-PC0 1 = INPUT 0 = OUTPUT PORT B 1 = INPUT 0 = OUTPUT 8 PC7 OBFA INTE 1 PC6 ACKA INTE 2 PC4 STBA PC5 IBFA WR GROUP B MODE 0 = MODE 0 1 = MODE 1 PC2-PC0 RD FIGURE 11. MODE CONTROL WORD 3 I/O FIGURE 12. MODE 2 DATA FROM CPU TO 82C55A WR tAOB OBF tWOB INTR tAK ACK tST STB tSIB IBF tAD tPS tKD PERIPHERAL BUS tRIB tPH RD DATA FROM PERIPHERAL TO 82C55A DATA FROM 82C55A TO PERIPHERAL DATA FROM 82C55A TO CPU NOTE: Any sequence where WR occurs before ACK and STB occurs before RD is permissible. (INTR = IBF • MASK • STB • RD ÷ OBF • MASK • ACK • WR) FIGURE 13. MODE 2 (BI-DIRECTIONAL) 11 82C55A MODE 2 AND MODE 0 (INPUT) MODE 2 AND MODE 0 (OUTPUT) PC3 PA7-PA0 1 1 0 1 1/0 PC2-PC0 1 = INPUT 0 = OUTPUT PA7-PA0 8 OBFA PC7 CONTROL WORD D7 D6 D5 D4 D3 D2 D1 D0 PC6 ACKA PC4 STBA PC5 IBFA PC2-PC0 PC3 INTRA 3 CONTROL WORD D7 D6 D5 D4 D3 D2 D1 D0 1 1 0 ACKA PC4 STBA IBFA PC5 3 I/O 8 WR MODE 2 AND MODE 1 (INPUT) PC3 PA7-PA0 CONTROL WORD D7 D6 D5 D4 D3 D2 D1 D0 0 PA7-PA0 8 OBFA PC6 ACKA PC4 STBA PC5 IBFA PC1 PC3 INTRA PC7 PB7-PB0 WR PC6 PB7, PB0 8 MODE 2 AND MODE 1 (OUTPUT) RD OBFA RD PB7-PB0 1 8 PC7 PC2-PC0 I/O WR 1 1/0 PC2-PC0 1 = INPUT 0 = OUTPUT RD 1 0 INTRA CONTROL WORD D7 D6 D5 D4 D3 D2 D1 D0 1 1 1 1 OBFB PC2 ACKB PC0 INTRB RD WR FIGURE 14. MODE 2 COMBINATIONS 12 8 PC7 OBFA PC6 ACKA PC4 STBA PC5 IBFA PB7-PB0 8 INTRA 8 PC2 STBB PC1 IBFB PC0 INTRB 82C55A MODE DEFINITION SUMMARY MODE 1 MODE 0 MODE 2 IN OUT IN OUT PA0 PA1 PA2 PA3 PA4 PA5 PA6 PA7 In In In In In In In In Out Out Out Out Out Out Out Out In In In In In In In In Out Out Out Out Out Out Out Out PB0 PB1 PB2 PB3 PB4 PB5 PB6 PB7 In In In In In In In In Out Out Out Out Out Out Out Out In In In In In In In In Out Out Out Out Out Out Out Out PC0 PC1 PC2 PC3 PC4 PC5 PC6 PC7 In In In In In In In In Out Out Out Out Out Out Out Out INTRB IBFB STBB INTRA STBA IBFA I/O I/O INTRB OBFB ACKB INTRA I/O I/O ACKA OBFA Special Mode Combination Considerations GROUP A ONLY Mode 0 or Mode 1 Only I/O I/O I/O INTRA STBA IBFA ACKA OBFA INPUT CONFIGURATION There are several combinations of modes possible. For any combination, some or all of Port C lines are used for control or status. The remaining bits are either inputs or outputs as defined by a “Set Mode” command. D7 D6 D5 I/O I/O IBFA D4 D3 D2 INTEA INTRA INTEB GROUP A During a read of Port C, the state of all the Port C lines, except the ACK and STB lines, will be placed on the data bus. In place of the ACK and STB line states, flag status will appear on the data bus in the PC2, PC4, and PC6 bit positions as illustrated by Figure 17. D1 D0 IBFB INTRB GROUP B OUTPUT CONFIGURATION D7 D6 OBFA INTEA Through a “Write Port C” command, only the Port C pins programmed as outputs in a Mode 0 group can be written. No other pins can be affected by a “Write Port C” command, nor can the interrupt enable flags be accessed. To write to any Port C output programmed as an output in Mode 1 group or to change an interrupt enable flag, the “Set/Reset Port C Bit” command must be used. D5 D4 I/O I/O D3 D2 D1 D0 INTRA INTEB OBFB INTRB GROUP A GROUP B FIGURE 15. MODE 1 STATUS WORD FORMAT D7 D6 OBFA INTE1 D5 IBFA D4 INTE2 INTRA GROUP A With a “Set/Reset Port Cea Bit” command, any Port C line programmed as an output (including IBF and OBF) can be written, or an interrupt enable flag can be either set or reset. Port C lines programmed as inputs, including ACK and STB lines, associated with Port C fare not affected by a “Set/Reset Port C Bit” command. Writing to the corresponding Port C bit positions of the ACK and STB lines with the “Set Reset Port C Bit” command will affect the Group A and Group B interrupt enable flags, as illustrated in Figure 17. D3 D2 D1 D0 X X X GROUP B (Defined by Mode 0 or Mode 1 Selection) FIGURE 16. MODE 2 STATUS WORD FORMAT Current Drive Capability Any output on Port A, B or C can sink or source 2.5mA. This feature allows the 82C55A to directly drive Darlington type drivers and high-voltage displays that require such sink or source current. 13 82C55A Reading Port C Status (Figures 15 and 16) Applications of the 82C55A In Mode 0, Port C transfers data to or from the peripheral device. When the 82C55A is programmed to function in Modes 1 or 2, Port C generates or accepts “hand shaking” signals with the peripheral device. Reading the contents of Port C allows the programmer to test or verify the “status” of each peripheral device and change the program flow accordingly. The 82C55A is a very powerful tool for interfacing peripheral equipment to the microcomputer system. It represents the optimum use of available pins and flexible enough to interface almost any I/O device without the need for additional external logic. Each peripheral device in a microcomputer system usually has a “service routine” associated with it. The routine manages the software interface between the device and the CPU. The functional definition of the 82C55A is programmed by the I/O service routine and becomes an extension of the system software. By examining the I/O devices interface characteristics for both data transfer and timing, and matching this information to the examples and tables in the detailed operational description, a control word can easily be developed to initialize the 82C55A to exactly “fit” the application. Figures 18 through 24 present a few examples of typical applications of the 82C55A. There is not special instruction to read the status information from Port C. A normal read operation of Port C is executed to perform this function. INTERRUPT ENABLE FLAG POSITION ALTERNATE PORT C PIN SIGNAL (MODE) INTE B PC2 ACKB (Output Mode 1) or STBB (Input Mode 1) INTE A2 PC4 STBA (Input Mode 1 or Mode 2) INTE A1 PC6 ACKA (Output Mode 1 or Mode 2) FIGURE 17. INTERRUPT ENABLE FLAGS IN MODES 1 AND 2 INTERRUPT REQUEST PC3 PA0 PA1 PA2 PA3 PA4 PA5 MODE 1 PA6 (OUTPUT) PA7 PC7 PC6 PC5 PC4 HIGH SPEED PRINTER HAMMER RELAYS DATA READY ACK PAPER FEED FORWARD/REV. 82C55A PB0 PB1 PB2 PB3 PB4 MODE 1 PB5 (OUTPUT) PB6 PB7 PC1 PC2 PAPER FEED FORWARD/REV. RIBBON CARRIAGE SEN. DATA READY ACK PC0 INTERRUPT REQUEST CONTROL LOGIC AND DRIVERS FIGURE 18. PRINTER INTERFACE 14 82C55A INTERRUPT REQUEST PC3 MODE 1 (INPUT) PA0 PA1 PA2 PA3 PA4 PA5 PA6 PA7 R0 R1 R2 FULLY R3 DECODED R4 KEYBOARD R5 SHIFT CONTROL PC4 PC5 STROBE ACK INTERRUPT REQUEST PC3 MODE 1 (INPUT) 82C55A PB0 PB1 PB2 PB3 PB4 MODE 1 PB5 (OUTPUT) PB6 PB7 B0 B1 B2 BURROUGHS SELF-SCAN B3 DISPLAY B4 B5 BACKSPACE CLEAR 82C55A MODE 0 (INPUT) DATA READY ACK BLANKING CANCEL WORD PC1 PC2 PC6 PC7 PA0 PA1 PA2 PA3 PA4 PA5 PA6 PA7 R0 R1 R2 FULLY R3 DECODED R4 KEYBOARD R5 SHIFT CONTROL PC4 PC5 PC6 PC7 STROBE ACK BUST LT TEST LT TERMINAL ADDRESS PB0 PB1 PB2 PB3 PB4 PB5 PB6 PB7 INTERRUPT REQUEST FIGURE 20. KEYBOARD AND TERMINAL ADDRESS INTERFACE FIGURE 19. KEYBOARD AND DISPLAY INTERFACE INTERRUPT REQUEST PA0 PA1 PA2 PA3 PA4 MODE 0 PA5 (OUTPUT) PA6 PA7 PC4 PC5 PC6 PC7 82C55A PC0 PC1 BIT SET/RESET PC2 PC3 PB0 PB1 PB2 MODE 0 (INPUT) PB3 PC4 PC5 PC6 PC7 LSB PC3 12-BIT A/D CONVERTER (DAC) PA0 PA1 PA2 PA3 PA4 PA5 MODE 1 PA6 (OUTPUT) PA7 ANALOG OUTPUT PC7 PC6 PC5 PC4 DATA READY ACK BLANKED BLACK/WHITE PC2 PC1 PC0 ROW STB COLUMN STB CURSOR H/V STB 82C55A STB DATA SAMPLE EN STB LSB 8-BIT D/A CONVERTER (ADC) R0 R1 R2 CRT CONTROLLER R3 • CHARACTER GEN. • REFRESH BUFFER R4 • CURSOR CONTROL R5 SHIFT CONTROL PB0 MODE 0 PB1 (OUTPUT) PB2 PB3 PB4 PB5 PB6 PB7 ANALOG INPUT MAB FIGURE 21. DIGITAL TO ANALOG, ANALOG TO DIGITAL CURSOR/ROW/COLUMN ADDRESS H&V FIGURE 22. BASIC CRT CONTROLLER INTERFACE 15 82C55A INTERRUPT REQUEST INTERRUPT REQUEST PC3 MODE 2 PC3 PA0 PA1 PA2 PA3 PA4 PA5 PA6 PA7 D0 D1 D2 D3 D4 D5 D6 D7 PC4 PC5 PC7 PC6 DATA STB ACK (IN) DATA READY ACK (OUT) PC2 PC1 PC0 TRACK “0” SENSOR SYNC READY INDEX FLOPPY DISK CONTROLLER AND DRIVE MODE 1 (INPUT) 82C55A PA0 PA1 PA2 PA3 PA4 PA5 PA6 PA7 R0 R1 R2 R3 R4 R5 R6 R7 PC4 PC5 PC6 STB ACK STOP/GO PC0 PC1 PC2 START/STOP LIMIT SENSOR (H/V) OUT OF FLUID MACHINE TOOL 82C55A PB0 PB1 PB2 MODE 0 PB3 (OUTPUT) PB4 PB5 PB6 PB7 MODE 0 (INPUT) ENGAGE HEAD FORWARD/REV. READ ENABLE WRITE ENABLE DISC SELECT ENABLE CRC TEST BUSY LT PB0 PB1 PB2 MODE 0 PB3 (OUTPUT) PB4 PB5 PB6 PB7 FIGURE 23. BASIC FLOPPY DISC INTERFACE B LEVEL PAPER TAPE READER CHANGE TOOL LEFT/RIGHT UP/DOWN HOR. STEP STROBE VERT. STEP STROBE SLEW/STEP FLUID ENABLE EMERGENCY STOP FIGURE 24. MACHINE TOOL CONTROLLER INTERFACE 16 82C55A TA = 25oC Absolute Maximum Ratings Thermal Information Thermal Resistance (Typical, Note 1) θJA θJC CERDIP Package . . . . . . . . . . . . . . . . 50oC/W 10oC/W CLCC Package . . . . . . . . . . . . . . . . . . 65oC/W 14oC/W PDIP Package . . . . . . . . . . . . . . . . . . . 50oC/W N/A PLCC Package . . . . . . . . . . . . . . . . . . 46oC/W N/A Maximum Storage Temperature Range . . . . . . . . . .-65oC to 150oC Maximum Junction Temperature CDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175oC PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150oC Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300oC (PLCC Lead Tips Only) Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +8.0V Input, Output or I/O Voltage . . . . . . . . . . . . GND-0.5V to VCC+0.5V ESD Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class 1 Operating Conditions Voltage Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +4.5V to 5.5V Operating Temperature Range C82C55A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0oC to 70oC I82C55A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40oC to 85oC M82C55A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55oC to 125oC Die Characteristics Gate Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000 Gates CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTE: 1. θJA is measured with the component mounted on an evaluation PC board in free air. Electrical Specifications VCC = 5.0V ±10%; TA = 0oC to +70oC (C82C55A); TA = -40oC to +85oC (I82C55A); TA = -55oC to +125oC (M82C55A) LIMITS SYMBOL PARAMETER MIN MAX UNITS TEST CONDITIONS VIH Logical One Input Voltage 2.0 2.2 - V I82C55A, C82C55A, M82C55A VIL Logical Zero Input Voltage - 0.8 V VOH Logical One Output Voltage 3.0 VCC -0.4 - V IOH = -2.5mA, IOH = -100µA VOL Logical Zero Output Voltage - 0.4 V IOL +2.5mA II Input Leakage Current -1.0 +1.0 µA VIN = VCC or GND, DIP Pins: 5, 6, 8, 9, 35, 36 IO I/O Pin Leakage Current -10 +10 µA VO = VCC or GND DIP Pins: 27 - 34 IBHH Bus Hold High Current -50 -400 µA VO = 3.0V. Ports A, B, C IBHL Bus Hold Low Current 50 400 µA VO = 1.0V. Port A ONLY IDAR Darlington Drive Current -2.5 Note 2, 4 mA Ports A, B, C. Test Condition 3 ICCSB Standby Power Supply Current - 10 µA VCC = 5.5V, VIN = VCC or GND. Output Open ICCOP Operating Power Supply Current - 1 mA/MHz TA = +25oC, VCC = 5.0V, Typical (See Note 3) NOTES: 2. No internal current limiting exists on Port Outputs. A resistor must be added externally to limit the current. 3. ICCOP = 1mA/MHz of Peripheral Read/Write cycle time. (Example: 1.0µs I/O Read/Write cycle time = 1mA). 4. Tested as VOH at -2.5mA. Capacitance SYMBOL TA = 25oC PARAMETER TYPICAL UNITS CIN Input Capacitance 10 pF CI/O I/O Capacitance 20 pF 17 TEST CONDITIONS FREQ = 1MHz, All Measurements are referenced to device GND 82C55A AC Electrical Specifications VCC = +5V± 10%, GND = 0V; TA = -55oC to +125oC (M82C55A) (M82C55A-5); TA = -40oC to +85oC (I82C55A) (I82C55A-5); TA = 0oC to +70oC (C82C55A) (C82C55A-5) 82C55A-5 SYMBOL PARAMETER 82C55A MIN MAX MIN MAX UNITS TEST CONDITIONS READ TIMING (1) tAR Address Stable Before RD 0 - 0 - ns (2) tRA Address Stable After RD 0 - 0 - ns (3) tRR RD Pulse Width 250 - 150 - ns (4) tRD Data Valid From RD - 200 - 120 ns 1 (5) tDF Data Float After RD 10 75 10 75 ns 2 (6) tRV Time Between RDs and/or WRs 300 - 300 - ns WRITE TIMING (7) tAW Address Stable Before WR 0 - 0 - ns (8) tWA Address Stable After WR 20 - 20 - ns (9) tWW WR Pulse Width 100 - 100 - ns (10) tDW Data Valid to WR High 100 - 100 - ns (11) tWD Data Valid After WR High 30 - 30 - ns OTHER TIMING (12) tWB WR = 1 to Output - 350 - 350 ns 1 (13) tIR Peripheral Data Before RD 0 - 0 - ns (14) tHR Peripheral Data After RD 0 - 0 - ns (15) tAK ACK Pulse Width 200 - 200 - ns (16) tST STB Pulse Width 100 - 100 - ns (17) tPS Peripheral Data Before STB High 20 - 20 - ns (18) tPH Peripheral Data After STB High 50 - 50 - ns (19) tAD ACK = 0 to Output - 175 - 175 ns 1 (20) tKD ACK = 1 to Output Float 20 250 20 250 ns 2 (21) tWOB WR = 1 to OBF = 0 - 150 - 150 ns 1 (22) tAOB ACK = 0 to OBF = 1 - 150 - 150 ns 1 (23) tSIB STB = 0 to IBF = 1 - 150 - 150 ns 1 (24) tRIB RD = 1 to IBF = 0 - 150 - 150 ns 1 (25) tRIT RD = 0 to INTR = 0 - 200 - 200 ns 1 (26) tSIT STB = 1 to INTR = 1 - 150 - 150 ns 1 (27) tAIT ACK = 1 to INTR = 1 - 150 - 150 ns 1 (28) tWIT WR = 0 to INTR = 0 - 200 - 200 ns 1 (29) tRES Reset Pulse Width 500 - 500 - ns 1, (Note) NOTE: Period of initial Reset pulse after power-on must be at least 50µsec. Subsequent Reset pulses may be 500ns minimum. 18 82C55A Timing Waveforms tRR (3) RD tIR (13) tHR (14) INPUT tAR (1) tRA (2) CS, A1, A0 D7-D0 tRD (4) tDF (5) FIGURE 25. MODE 0 (BASIC INPUT) tWW (9) WR tDW (10) tWD (11) D7-D0 tAW (7) tWA (8) CS, A1, A0 OUTPUT tWS (12) FIGURE 26. MODE 0 (BASIC OUTPUT) tST (16) STB IBF tSIB (23) tSIT (26) tRIB (24) tRIT (25) INTR RD tPH (18) INPUT FROM PERIPHERAL tPS (17) FIGURE 27. MODE 1 (STROBED INPUT) 19 82C55A Timing Waveforms (Continued) tWOB (21) WR tAOB (22) OBF tWIT (28) INTR ACK tAK (15) tAIT (27) OUTPUT tWB (12) FIGURE 28. MODE 1 (STROBED OUTPUT) DATA FROM CPU TO 82C55A WR (NOTE) tAOB (22) OBF tWOB (21) INTR tAK (15) ACK tST (16) STB (NOTE) IBF tSIB (23) tAD (19) tPS (17) tKD (20) PERIPHERAL BUS tRIB (24) tPH (18) RD DATA FROM PERIPHERAL TO 82C55A DATA FROM 82C55A TO PERIPHERAL DATA FROM 82C55A TO CPU FIGURE 29. MODE 2 (BI-DIRECTIONAL) NOTE: Any sequence where WR occurs before ACK and STB occurs before RD is permissible. (INTR = IBF • MASK • STB • RD • OBF • MASK • ACK • WR) 20 82C55A Timing Waveforms (Continued) A0-A1, CS A0-A1, CS tWA (8) tAW (7) tRA (2) tAR (1) tRR (3) DATA BUS RD tDW (10) tWD (11) (4) tRD tDF (5) DATA BUS WR VALID HIGH IMPEDANCE tWW (9) FIGURE 30. WRITE TIMING FIGURE 31. READ TIMING AC Test Circuit AC Testing Input, Output Waveforms V1 INPUT OUTPUT VIH + 0.4V VOH 1.5V R1 OUTPUT FROM DEVICE UNDER TEST TEST POINT R2 1.5V VOL VIL - 0.4V AC Testing: All AC Parameters tested as per test circuits. Input RISE and FALL times are driven at 1ns/V. C1 (SEE NOTE) TEST CONDITION DEFINITION TABLE NOTE: Includes STRAY and JIG Capacitance TEST CONDITION V1 R1 R2 C1 1 1.7V 523Ω Open 150pF 2 VCC 2kΩ 1.7kΩ 50pF 3 1.5V 750Ω Open 50pF Burn-In Circuits 37 F14 F4 5 36 F2 F3 6 35 F5 GND F0 7 8 34 33 GND 6 5 4 3 2 1 44 43 42 41 40 7 39 8 38 F5 F0 9 37 F15 F1 F10 10 36 11 35 F11 F12 F6 12 34 F13 F7 13 33 F14 F8 14 32 F15 F15 F11 F2 4 F14 F13 F9 F13 38 F12 3 F6 F12 F8 F7 F11 39 F8 40 2 F9 1 F7 F4 F6 F11 MR82C55A CLCC F3 MD82C55A CERDIP F1 9 32 F10 10 31 F13 F6 11 30 F14 F7 12 29 F15 F8 13 28 F11 F9 15 31 F11 F9 14 27 F12 F10 16 30 F12 F10 15 26 F6 17 29 F6 16 25 F13 F7 17 24 F14 F8 18 23 F15 F9 19 22 F11 F10 20 21 F12 NOTES: 1. VCC = 5.5V ± 0.5V 2. VIH = 4.5V ± 10% 3. VIL = -0.2V to 0.4V 4. GND = 0V 18 19 20 21 22 23 24 25 26 27 28 C1 NOTES: 1. C1 = 0.01µF minimum 2. All resistors are 47kΩ ± 5% 3. f0 = 100kHz ± 10% 4. f1 = f0 ÷ 2; f2 = f1 ÷ 2; . . . ; f15 = f14 ÷ 2 21 VCC F13 F14 F15 F11 F12 F10 F7 C1 F9 VCC F8 F12 82C55A Die Characteristics DIE DIMENSIONS: 95 x 100 x 19 ±1mils GLASSIVATION: Type: SiO2 Thickness: 8kÅ ±1kÅ METALLIZATION: Type: Silicon - Aluminum Thickness: 11kÅ ±1kÅ WORST CASE CURRENT DENSITY: 0.78 x 105 A/cm2 Metallization Mask Layout 82C55A RD PA0 PA1 PA2 PA3 PA4 PA5 PA6 PA7 WR RESET CS GND D0 A1 D1 A0 D2 PC7 D3 PC6 D4 PC5 D5 PC4 D6 PC0 D7 PC1 VCC PC2 PD3 PB0 PB1 PB2 22 PB3 PB4 PB5 PB6 PB7 82C55A Dual-In-Line Plastic Packages (PDIP) E40.6 (JEDEC MS-011-AC ISSUE B) N 40 LEAD DUAL-IN-LINE PLASTIC PACKAGE E1 INDEX AREA 1 2 3 INCHES N/2 SYMBOL -B- -C- A2 SEATING PLANE e B1 D1 B 0.010 (0.25) M A1 eC C A B S MAX NOTES - 0.250 - 6.35 4 0.015 - 0.39 - 4 A2 0.125 0.195 3.18 4.95 - B 0.014 0.022 0.356 0.558 - C L B1 0.030 0.070 0.77 1.77 8 eA C 0.008 0.015 0.204 0.381 - D 1.980 2.095 D1 0.005 - A L D1 MIN A E BASE PLANE MAX A1 -AD MILLIMETERS MIN C eB NOTES: 1. Controlling Dimensions: INCH. In case of conflict between English and Metric dimensions, the inch dimensions control. 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of Publication No. 95. 4. Dimensions A, A1 and L are measured with the package seated in JEDEC seating plane gauge GS-3. 5. D, D1, and E1 dimensions do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.010 inch (0.25mm). 6. E and eA are measured with the leads constrained to be perpendicular to datum -C- . 7. eB and eC are measured at the lead tips with the leads unconstrained. eC must be zero or greater. 8. B1 maximum dimensions do not include dambar protrusions. Dambar protrusions shall not exceed 0.010 inch (0.25mm). 9. N is the maximum number of terminal positions. 10. Corner leads (1, N, N/2 and N/2 + 1) for E8.3, E16.3, E18.3, E28.3, E42.6 will have a B1 dimension of 0.030 - 0.045 inch (0.76 - 1.14mm). 50.3 53.2 5 - 5 0.13 E 0.600 0.625 15.24 15.87 6 E1 0.485 0.580 12.32 14.73 5 e 0.100 BSC 2.54 BSC - eA 0.600 BSC 15.24 BSC 6 eB - 0.700 - 17.78 7 L 0.115 0.200 2.93 5.08 4 N 40 40 9 Rev. 0 12/93 23 82C55A Plastic Leaded Chip Carrier Packages (PLCC) 0.042 (1.07) 0.048 (1.22) PIN (1) IDENTIFIER N44.65 (JEDEC MS-018AC ISSUE A) 0.042 (1.07) 0.056 (1.42) 0.004 (0.10) C 0.025 (0.64) R 0.045 (1.14) 0.050 (1.27) TP C L D2/E2 C L E1 E D2/E2 VIEW “A” A1 A D1 D 0.020 (0.51) MAX 3 PLCS 0.020 (0.51) MIN 0.045 (1.14) MIN INCHES MILLIMETERS SYMBOL MIN MAX MIN MAX NOTES A 0.165 0.180 4.20 4.57 - A1 0.090 0.120 2.29 3.04 - D 0.685 0.695 17.40 17.65 - D1 0.650 0.656 16.51 16.66 3 D2 0.291 0.319 7.40 8.10 4, 5 E 0.685 0.695 17.40 17.65 - E1 0.650 0.656 16.51 16.66 3 E2 0.291 0.319 7.40 8.10 4, 5 N 44 44 6 Rev. 2 11/97 SEATING -C- PLANE 0.026 (0.66) 0.032 (0.81) 44 LEAD PLASTIC LEADED CHIP CARRIER PACKAGE 0.013 (0.33) 0.021 (0.53) 0.025 (0.64) MIN VIEW “A” TYP. NOTES: 1. Controlling dimension: INCH. Converted millimeter dimensions are not necessarily exact. 2. Dimensions and tolerancing per ANSI Y14.5M-1982. 3. Dimensions D1 and E1 do not include mold protrusions. Allowable mold protrusion is 0.010 inch (0.25mm) per side. Dimensions D1 and E1 include mold mismatch and are measured at the extreme material condition at the body parting line. 4. To be measured at seating plane -C- contact point. 5. Centerline to be determined where center leads exit plastic body. 6. “N” is the number of terminal positions. 24 82C55A Ceramic Dual-In-Line Frit Seal Packages (CERDIP) F40.6 MIL-STD-1835 GDIP1-T40 (D-5, CONFIGURATION A) LEAD FINISH c1 40 LEAD CERAMIC DUAL-IN-LINE FRIT SEAL PACKAGE -D- -A- BASE METAL SYMBOL E M -Bbbb S C A-B S -C- S1 - 0.225 - 5.72 - 0.026 0.36 0.66 2 b1 0.014 0.023 0.36 0.58 3 b2 0.045 0.065 1.14 1.65 - b3 0.023 0.045 0.58 1.14 4 c 0.008 0.018 0.20 0.46 2 c1 0.008 0.015 0.20 0.38 3 D - 2.096 - 53.24 5 E 0.510 0.620 15.75 5 eA b2 b ccc M C A - B S e D S eA/2 NOTES 0.014 α A A MAX b A L MIN A Q SEATING PLANE MAX M (b) D BASE PLANE MILLIMETERS MIN b1 SECTION A-A D S INCHES (c) c e aaa M C A - B S D S NOTES: 1. Index area: A notch or a pin one identification mark shall be located adjacent to pin one and shall be located within the shaded area shown. The manufacturer’s identification shall not be used as a pin one identification mark. 2. The maximum limits of lead dimensions b and c or M shall be measured at the centroid of the finished lead surfaces, when solder dip or tin plate lead finish is applied. 3. Dimensions b1 and c1 apply to lead base metal only. Dimension M applies to lead plating and finish thickness. 4. Corner leads (1, N, N/2, and N/2+1) may be configured with a partial lead paddle. For this configuration dimension b3 replaces dimension b2. 5. This dimension allows for off-center lid, meniscus, and glass overrun. 6. Dimension Q shall be measured from the seating plane to the base plane. 7. Measure dimension S1 at all four corners. 8. N is the maximum number of terminal positions. 9. Dimensioning and tolerancing per ANSI Y14.5M - 1982. 10. Controlling dimension: INCH. 12.95 0.100 BSC 2.54 BSC - eA 0.600 BSC 15.24 BSC - eA/2 0.300 BSC 7.62 BSC - L 0.125 0.200 3.18 5.08 - Q 0.015 0.070 0.38 1.78 6 S1 0.005 - 0.13 - 7 α 90o 105o 90o 105o - aaa - 0.015 - 0.38 - bbb - 0.030 - 0.76 - ccc - 0.010 - 0.25 - M - 0.0015 - 0.038 2, 3 N 40 40 8 Rev. 0 4/94 25 82C55A Ceramic Leadless Chip Carrier Packages (CLCC) J44.A MIL-STD-1835 CQCC1-N44 (C-5) 44 PAD CERAMIC LEADLESS CHIP CARRIER PACKAGE 0.010 S E H S D INCHES D3 j x 45o E3 B h x 45o 0.010 S E F S A A1 PLANE 2 MAX MIN MAX NOTES A 0.064 0.120 1.63 3.05 6, 7 A1 0.054 0.088 1.37 2.24 - B 0.033 0.039 0.84 0.99 4 B1 0.022 0.028 0.56 0.71 2, 4 B1 e L -H- L3 - 0.022 0.15 0.56 D 0.640 0.662 16.26 16.81 - D1 0.500 BSC 12.70 BSC - D2 0.250 BSC 6.35 BSC - D3 - 0.662 E 0.640 0.662 16.26 16.81 2 16.81 - E1 0.500 BSC 12.70 BSC - E2 0.250 BSC 6.35 BSC - E3 - 0.662 0.050 BSC 0.015 - - 16.81 1.27 BSC 0.38 2 - - 2 h 0.040 REF 1.02 REF 5 j 0.020 REF 0.51 REF 5 L 0.045 0.055 1.14 1.40 - L1 0.045 0.055 1.14 1.40 - L2 0.075 0.095 1.90 2.41 - L3 0.003 0.015 0.08 0.38 - ND 11 11 3 NE 11 11 3 N 44 44 -F- 3 Rev. 0 5/18/94 NOTES: B3 E1 E2 1.83 REF 0.006 e1 0.007 M E F S H S 0.072 REF B3 e PLANE 1 -E- MIN B2 E MILLIMETERS SYMBOL 1. Metallized castellations shall be connected to plane 1 terminals and extend toward plane 2 across at least two layers of ceramic or completely across all of the ceramic layers to make electrical connection with the optional plane 2 terminals. L2 B2 2. Unless otherwise specified, a minimum clearance of 0.015 inch (0.38mm) shall be maintained between all metallized features (e.g., lid, castellations, terminals, thermal pads, etc.) L1 3. Symbol “N” is the maximum number of terminals. Symbols “ND” and “NE” are the number of terminals along the sides of length “D” and “E”, respectively. D2 e1 D1 4. The required plane 1 terminals and optional plane 2 terminals (if used) shall be electrically connected. 5. The corner shape (square, notch, radius, etc.) may vary at the manufacturer’s option, from that shown on the drawing. 6. Chip carriers shall be constructed of a minimum of two ceramic layers. 7. Dimension “A” controls the overall package thickness. The maximum “A” dimension is package height before being solder dipped. 8. Dimensioning and tolerancing per ANSI Y14.5M-1982. 9. Controlling dimension: INCH. 26