DC/DC Converters SPECIFICATIONS CTDD3120DF-S1K-3M Series Wide Input Isolated & Regulated 3W Output, Single Output Not shown at actual size. RoHS Compliant ctparts.com Part Number Vin Nom. (VDC) Input Range (VDC) Vin Max.* (VDC) Vout (VDC) CTDD3120DF-0505-S1K-3M CTDD3120DF-0509-S1K-3M CTDD3120DF-0512-S1K-3M CTDD3120DF-0515-S1K-3M 5 5 5 5 4.5-9 4.5-9 4.5-9 4.5-9 11 11 11 11 5 9 12 15 CTDD3120DF-1205-S1K-3M CTDD3120DF-1209-S1K-3M CTDD3120DF-1212-S1K-3M CTDD3120DF-1215-S1K-3M 12 12 12 12 9-18 9-18 9-18 9-18 22 22 22 22 CTDD3120DF-1505-S1K-3M CTDD3120DF-1509-S1K-3M CTDD3120DF-1512-S1K-3M CTDD3120DF-1515-S1K-3M 15 15 15 15 12-24 12-24 12-24 12-24 CTDD3120DF-2405-S1K-3M CTDD3120DF-2409-S1K-3M CTDD3120DF-2412-S1K-3M CTDD3120DF-2415-S1K-3M 24 24 24 24 CTDD3120DF-4805-S1K-3M CTDD3120DF-4809-S1K-3M CTDD3120DF-4812-S1K-3M CTDD3120DF-4815-S1K-3M 48 48 48 48 Iout Max. (mA) Iout Min. (mA) Effi. Typ. (%) 500 330 250 200 50 33 25 20 70 72 73 75 5 9 12 15 500 330 250 200 50 33 25 20 70 75 76 78 30 30 30 30 5 9 12 15 500 330 250 200 50 33 25 20 71 74 76 76 18-36 18-36 18-36 18-36 40 40 40 40 5 9 12 15 500 330 250 200 50 33 25 20 70 75 81 81 36-72 36-72 36-72 36-72 80 80 80 80 5 9 12 15 500 330 250 200 50 33 25 20 78 82 82 83 *If Input voltage above specified may cause permanent damage to the device ISOLATION SPECIFICATIONS FEATURES Efficiency: To 83% Temperature Range: -40°C to +85°C Isolation: 1KVDC Miscellaneous: Wide (2:1) Input Range. Single Output. Metal Shielding Package. No heat sink required. Industry Standard Pin out. Custom service available. Samples available. CHARACTERISTICS Test Condition MIN Isolation Voltage Flash tested for 1 minute 1000 VDC Test at 500VDC 1000 MΩ Isolation Resistance Test Condition 3W Output Power Units MIN TYP MAX Units 3 W ±1 ±3 % Output voltage accuracy Refer to Recommended Circuit Load regulation From 10% to 100% load ±0.5 ±0.75 % Line regulation Input Voltage from low to high ±0.2 ±0.5 % Temperature drift (Vout) Refer to Temp. Derating Graph Ripple 20Hz to 300KHz Bandwidth Noise DC-20MHz Bandwidth Switching frequency 100% load, nominal input voltage 80 Switching frequency 10% load, nominal input voltage 250 0.03 %/°C 30 60 mVp-p 80 150 mVp-p 200 KHz 600 KHz Note: 1. All specifications measured at TA=25°C, humidity<75%, nominal input voltage and rated output unless otherwise specified. TYPICAL CHARACTERISTICS Temperature Derating Graph 120 100 80 60 Safe Operating Area 40 20 0 120 40 71 85 Ambient Temperature (°C) 12.18.06 Technologies MAX 0.3 0 -40 CENTRAL TYP OUTPUT SPECIFICATIONS Item Output Power (%) Output Short Circuit Protection: Continuous Temperature Rise at Full Load: 30°C (Typ.) Cooling: Free air convection No Load, Power Consumption: 100mW (typical) Operating Temperature Range: -40°C to +85°C Storage Temperature Range: -55°C to +125°C Lead Temperature: 300°C (1.5mm from case for 10 seconds) Storage Humidity Range: < 95% Case Material: Metal MTBF: >3,500,000 hours Miscellaneous: RoHS Compliant. Item Manufacturer of Passive and Discrete Semiconductor Components 800-684-5322 Inside US 949-453-1811 Outside US Copyright © 2006 by CT Magnetics, DBA Central Technologies. All rights reserved. CT Magnetics reserves the right to make improvements or change specifications without notice DC/DC Converters ctparts.com CTDD3120DF-S1K-3M Series Wide Input Isolated & Regulated 3W Output, Single Output OUTLINE DIMENSIONS & RECOMMENDED FOOTPRINT DETAILS CTDD3120DF-S1K-3M Package 2 Bottom View Side View 31.80 10.0 3 0.50 9 10 11 15.24 20.30 23 22 16 15 14 2.54 5.08 4.00 22.86 Note: All pins on a 2.54mm pitch; all pin diameters are 0.50mm; all dimensions in mm. (Tolerance:±0.25) PIN CONNECTIONS Pin Function 2, 3 9, 10, 11, 15 14 16 22 23 GND NC +Vo 0V Vin Vin Bottom View 2 3 9 10 11 23 22 16 15 14 RECOMMENDED CIRCUIT All the CTDD3120DF-S1K-3M Series have been tested according to the following recommended testing circuit before leaving factory. This series should be tested under load. Never be tested under no load (See figure 1 & 2). If you want to further decrease the input/output ripple, you can increase capacitance properly or choose capacitors with low ESR. However, the capacitance should not be too high (See table 1). If you want to use the products in high EMI, please choose our metal packaged products. External Capacitor Table (table 1) C in 5V & 12V 100µF 24V & 48V 10µF C out (0+70°C) Figure 2 C out (-40+85°C) lp Figure 1 100µF (electrolytic capacitor) 47µF (tantalum capacitor) Vin +Cin Cout DC DC + Vout Input Current (A) Vin Input Voltage Range 0V GND Input Voltage (V) CENTRAL Technologies 12.18.06 Manufacturer of Passive and Discrete Semiconductor Components 800-684-5322 Inside US 949-453-1811 Outside US Copyright © 2006 by CT Magnetics, DBA Central Technologies. All rights reserved. CT Magnetics reserves the right to make improvements or change specifications without notice