COMCHIP SURFACE MOUNT ZENER DIODE SMD DIODE SPECIALIST CZRA4740 thru CZRA4764 Voltage: 10-100 Volts Power: 1.0 Watts FEATURES - For surface mounted applications in order to optimize board space - Low profile package - Built-in strain relief - Glass passivated junction - Low inductance - Typical IR less than 5.0uA above 11V - High temper ature soldering : 260°C / 10 seconds at terminals - Plastic package has Underwriters Laboratory Flammability Classification 94V-O DO-214AC (SMA) 0.067(1.70) 0.051(1.29) 0.110(2.79) 0.086(2.18) 0.180(4.57) 0.160(4.06) U 0.012(0.31) 0.006(0.15) 0.091(2.31) 0.067(1.70) 0.059(1.50) 0.035(0.89) MECHANICAL DATA Case: JEDEC DO-214AC, Molded plastic over passivated junction Terminals: Solder plated, solderable per MIL-STD-750, method 2026 Polarity: Color band denotes positive end(cathode) Standard Packaging: 12mm tape(EIA-481) Weight: 0.002 ounce, 0.064 gram 0.209(5.31) 0.185(4.70) 0.008(0.20) 0.004(0.10) Dimensionsininchesand(millimeters) Maximum Ratings and Electrical Characterics Ratings at 25°C ambient temperature unless otherwise specified. Peak Pulse Power Dissipation on T A= 50°C (Note A) Derate above 50°C Peak forward Surge Current 8.3ms single half sine-wave superimposed on rated load(JEDEC Method) (Note B) Operating Junction and Storage Temperature Range SYMBOL PD VALUE 1.0 6.67 IFSM 10 UNITS Watts mW/°C Amps TJ,TSTG -55 to +150 °C NOTES: 2 A. Mounted on 5.0mm (.013mm thick) land areas. B. Measured on 8.3ms, single half sine-wave or equivalent square wave, duty cycle = 4 pulses per minute maximum. MDS0208021B Comchip Technology Corporation • Tel: 510-657-8671 • Fax: 510-657-8921 • www.comchiptech.com Page 1 COMCHIP SURFACE MOUNT ZENER DIODE SMD DIODE SPECIALIST ELECTRICAL CHARACTERISTICS (TA=25°C unless otherwise noted) (VF=1.2Volts Max, IF=200mA for all types.) Device (Note 1.) CZRA4740 CZRA4741 CZRA4742 CZRA4743 CZRA4744 CZRA4745 CZRA4746 CZRA4747 CZRA4748 CZRA4749 CZRA4750 CZRA4751 CZRA4752 CZRA4753 CZRA4754 CZRA4755 CZRA4756 CZRA4757 CZRA4758 CZRA4759 CZRA4760 CZRA4761 CZRA4762 CZRA4763 CZRA4764 Nominal Zener Voltage VZ @ IZT (Note 2, 3) Test current IZT (Volts) (mA) (Ohms) (Ohms) (mA) (uA) (Volts) 10 11 12 13 15 16 18 20 22 24 27 30 33 36 39 43 47 51 56 62 68 75 82 91 100 25 23 21 19 17 15.5 14 12.5 11.5 10.5 9.5 8.5 7.5 7 6.5 6 5.5 5 4.5 4 3.7 3.3 3 2.8 2.5 7 8 9 10 14 16 20 22 23 25 35 40 45 50 60 70 80 95 110 125 150 175 200 250 350 700 700 700 700 700 700 750 750 750 750 750 1000 1000 1000 1000 1500 1500 1500 2000 2000 2000 2000 3000 3000 3000 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 10 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 7.6 8.4 9.1 9.9 11.4 12.2 13.7 15.2 16.7 18.2 20.6 22.8 25.1 27.4 29.7 32.7 35.8 38.8 42.6 47.1 51.7 56 62.2 69.2 76 Maximum Zener Impedance (Note 4) ZZT @ IZT ZZK @ IZK IZK Leakage Current IR Surge Current @TA = 25°C (Note 5) VR Ir - mA 454 414 380 344 304 285 250 225 205 190 170 150 135 125 115 110 95 90 80 70 65 60 55 50 45 NOTE: 1. Tolerance and Type Number Designation. The type numbers listed have a standard tolerance on the nominal zener voltage of ± 5%. 2. Specials Available Include: A. Nominal zener voltages between the voltages shown and tighter voltage tolerances. B. Matched sets. 3. Zener Voltage (VZ) Measurement. Guarantees the zener voltage when measured at 90 seconds while maintaining the lead temperature (TL) at 30°C ± 1°C, from the diode body. 4. Zener Impedance (ZZ) Derivation. The zener impedance is derived from the 60 cycle ac voltage, which results when an ac current having an rms value equal to 10% of the dc zener current (IZT or IZK) is superimposed on IZT or IZK. 5. Surge Current (Ir) Non-Repetitive. The rating listed in the electrical characteristics table is maximum peak, non-repetitive, reverse surge current of 1/2 square wave or equivalent sine wave pulse of 1/120 second duration superimposed on the test current, IZT, per JEDEC registration; however, actual device capability is as described in Figure 5. MDS0208021B Comchip Technology Corporation • Tel: 510-657-8671 • Fax: 510-657-8921 • www.comchiptech.com Page 2 COMCHIP SURFACE MOUNT ZENER DIODE SMD DIODE SPECIALIST RATING AND CHARACTERISTICS CURVES PD, MAXIMUM POWER DISSIPATION (WATTS) CZRA4740 THRU CZRA4764 1.25 1.0 L = LEAD LENTGH TO HEAT SINK 0.75 0.50 0.25 0 0 20 40 60 80 100 120 140 160 180 200 TL, LEAD TEMPERATURE 100 +12 +10 +8.0 +6.0 +4.0 +2.0 0 -2.0 -4.0 2 VZ @ IZT RANGE 3 4 5 6 7 8 9 10 11 12 VZ, TEMPERATURE COEFFICIENT(mV/W) VZ, TEMPERATURE COEFFICIENT (mV/°C) Fig. 1-POWER TEMPERATURE DERATING CURVE 70 50 30 20 10 RANGE VZ @ IZT 7.0 5.0 3.0 2.0 1.0 10 20 VZ, ZENER VOLTAGE (VOLTS) 30 50 70 100 VZ, ZENER VOLTAGE (VOLTS) Fig. 2-TEMPERATURE COEFFICIENTS (-55°C TO +150°C TEMPERATURE RANGE; 90% OF THE UNITS ARE IN THE RANGES INDICATED.) 150 125 100 75 50 25 0 0 .1 .2 .3 .4 .5 .6 .7 .8 .9 1.0 L, LEAD LENGTH TO HEAT SINK (INCKES) Fig.3-TYPICAL THERMAL RESISTANCE VERSUS LEAD LENGTH MDS0208021B VZ, TEMPERATURE COEFFICIENT (mV/w) JL, JUNCTION TO LEAD THERMAL RESISTANCE (°C/W) 175 +6.0 NOTE:BELOW 3 VOLTS AND ABOVE 8 CHANGES IN ZENER CURRENT DO AFFECT TEMPERATURE +4.0 20mA +2.0 0 0.01mA 1.0mA -2.0 -4.0 3 4 5 VZ @ IZT TA = 25°C 6 7 8 VZ, ZENER VOLTAGE (VOLTS) Fig. 4-EFFECT OF ZENER CURRENT Comchip Technology Corporation • Tel: 510-657-8671 • Fax: 510-657-8921 • www.comchiptech.com Page3 COMCHIP SURFACE MOUNT ZENER DIODE SMD DIODE SPECIALIST RATING AND CHARACTERISTICS CURVES CZRA4740 THRU CZRA4764 Ppk, peak surge power (watts) 100 11V-91V NON-REPETITIVE 70 50 5% DUTY CYCLE 30 20 10 0.8V-10V NON-REPETITIVE RECTANGULAR WAVEFORM TJ = 25°C PRIOR TO INITIAL PULSE 10% DUTY CYCLE 7.0 5.0 3.0 20% DUTY CYCLE 2.0 1.0 0.01 0.02 0.05 0.1 0.2 0.5 1.0 2.0 5.0 10 20 50 100 200 500 PW, PULSE WIDTH This graph represents 90 percentile data point. For worst-case design characteristics, multiply surge power by 2/3 Fig. 5-MAXIMUM SURGE POWER Zz, dynamic impedance (ohms) Zz, dynamic impedance (ohms) 1000 TJ = 25°C IZ(ms) = 0.1IZ(dc) f = 60Hz 500 200 100 47V 50 27V 20 10 5.0 0.8V 2.0 1.0 0.1 0.2 0.5 1.0 2.0 5.0 10 20 50 100 1000 700 500 I = 1.0mA Z 200 100 5.0mA 70 50 20mA 20 10 7 5 2 1 1.0 2.0 3.0 TJ = 25°C IZ(ms) = 0.1IZ(dc) f = 60Hz 5.0 7.0 10 20 30 50 70 100 IZ, ZENER CURRENT (mA) IZ, ZENER CURRENT (mA) Fig. 6-EFFECT OF ZENER CURRENT ON ZENER IMPEDANCE Fig. 7-EFFECT OF ZENER VOLTAGE ON ZENER IMPEDANCE MDS0208021B Comchip Technology Corporation • Tel: 510-657-8671 • Fax: 510-657-8921 • www.comchiptech.com Page 4