D-XM-1W Series 1W,FIXED INPUT,1000V ISOLATED & UNREGULATED TWIN OUTPUT DC-DC CONVERTER PRODUCT PROGRAM Input Part Number FEATURES ◆Small footprint Output Voltage(VDC) Voltage Efficiency Current(MA) (%,Typ) Nominal Range (VDC) D030505XM-1W 3.3 2.97-3.63 5 100 10 70 D050303XM-1W 5 4.5-5.5 3.3 152 15 62 D050505XM-1W 5 4.5-5.5 5 100 10 71 Max Min. ◆SIP6 package ◆Temperature range: -40℃~+85℃ ◆1KVDC isolation ◆No Heat sink required ◆No external component required COMMON SPECIFICATIONS ◆Internal SMD Construction Item Test Conditions Min. Typ. Max. Units 95 % ◆ Industry standard pinout Storage humidity range ◆ RoHS Compliance Operating temperature -40 85 Storage temperature -55 125 ℃ Lead temperature 1.5mm from case for 10 seconds 300 15 Temp. rise at full load MODEL SELECTION D①05②05③05④X⑤ M⑥-1W⑦ ①Product Series ②Input Voltage ③The 1st Output Voltage ④The 2nd Output Voltage ⑤Fixed Input ⑥Mini SIP Package Style ⑦Rated Power 25 1 Short circuit protection* Free air convection Cooling Plastic(UL94-V0) Case material 1.4 MTBF g 3500 Weight K hours *Supply voltage must be discontinued at the end of short circuit duration. APPLICATIONS The D-XM-1W Series are specially designed for applications where a group of polar power supplies are isolated from the input power supply in a distributed power supply system on a circuit board. These products apply to: 1) Where the voltage of the input power supply is fixed (voltage variation ≤±10%); 2) Where isolation is necessary between input and output (isolation voltage ≤1000VDC); 3) Where the regulation of the output voltage and the output ripple noise are not demanding. Such as:purely digital circuits, ordinary low frequency analog circuits,and IGBT power device driving circuits. ISOLATION SPECIFICATIONS Item Test Conditions Min. Typ. Max. Isolation voltage (Vin/Vout) Tested for 1 minute and 1mA max 1000 VDC Isolation voltage (Vo1/Vo2) Tested for 1 minute and 1mA max 1000 VDC Isolation resistance (Vin/Vout) Test at 500VDC 1000 MΩ Isolation resistance (Vo1/Vo2) Test at 500VDC 1000 MΩ Units Isolation capacitance(Vin/Vout) 30 pF Isolation capacitance(Vo1/Vo2) 30 pF MICRODC reserves the copyright http://www.microdc.cn S Technical Enquiries-Email:[email protected] Tel:0086-20-86000646 Page 1 of 3 D-XM-1W Series TYPICAL CHARACTERISTICS OUTPUT SPECIFICATIONS Item Test Conditions Min. Output power Typ. Max. Units 1 W ±1.5 % 15 20 % 12.8 15 % 0.1 Line regulation For Vin change of 1% Load regulation 10% to 100% load (3.3V output) Load regulation 10% to 100% load(5V output) Output voltage accuracy See tolerance envelope graph Temperature drift 100% full load Ripple & Noise* 20MHz Bandwidth 75 Switching frequency Full load, nominal input 130 *Test ripple and noise by "Parallel cable"method. See detailed operation ±0.03 %/℃ 100 mVp-p KHz instructions at Testing of Power Converter section, application notes. RECOMMENDED CIRCUIT APPLICATION NOTE Requirement on output load To ensure this module can operate efficiently and reliably, During operation, the minimum output load could not be less than 10% of the full load . If the actual output power is very small , please connect a resistor with load , or use our company proper resistance at the output end in parallel to increase the products with a lower rated output power. Recommended circuit If you want to further decrease the input/output ripple , an "LC" filtering network may be connected to the input and output ends of the DC/DC converter, see (Figure 1). It should also be noted that the be staggered with inductance and the frequency of the "LC" filtering network should the DC/DC frequency to avoid mutual the output filter capacitor must be proper. If interference. However , the capacitance the capacitance is too big , a startup of problem might arise. For every channel of output , provided the safe and reliable operation is ensured , the recommended capacitance of its filter capacitor sees (Table 1). Output Voltage Regulation and Over-voltage Protection Circuit The simplest device for output voltage regulation, over-voltage and over-current protection is a linear voltage regulator with overheat protection that is connected to the input or output end in series (Figure 2). Overload Protection Under normal operating conditions, the output circuit of these products has no protection against overload . The simplest method is to connect a self-recovery fuse in series at the input end or add a circuit breaker to the circuit. No parallel connection or plug and play It's not recommended capacitor in to connect any external the application field with less than 0.5 watt output. http://www.microdc.cn Technical Enquiries-Email:[email protected] Tel:0086-20-86000646 Page 2 of 3 D-XM-1W Series OUTLINE DIMENSIONS ＆ FOOTPRINT DETAILS MECHANICAL DIMENSIONS RECOMMENDED FOOTPRINT TUBE OUTLINE DIMENSIONS Note: Unit:mm[ inch] Pin sect ion tolerances:±0.10mm[±0.004inch] General tolerances:±0.25mm[±0.010inch] Note: Unit :mm[inch] General tolerances:±0.50mm[±0.020inch] L=530mm[20.866inch] Tube Quantity: 30pcs L=220mm[8.661inch] Tube Quantity: 11pcs RoHS COMPLIANT INFORMATION This series is compatible with RoHS soldering systems with a peak wave solder temperature of 300°C for 10 seconds. The pin termination finish on the SIP package type is Tin Plate, Hot Dipped over Matte Tin with Nickel Preplate. The DIP types are Matte Tin over Nickel Preplate. Both types in this series are backward compatible with Sn/Pb soldering systems. Microdc Professional Power Module,Inc. Tel:0086-20-86000646 REACH COMPLIANT INFORMATION E-mail:[email protected] Website:http://www.microdc.cn http://www.microdc.cn This series has proven that this product does not contain harmful chemicals, it also has harmful chemical substances through the registration, inspection and approval. Technical Enquiries-Email:[email protected] Tel:0086-20-86000646 Page 3 of 3