D200ERU Series Low Cost, 4:1 Input Miniature, 2W SIP DC/DC Converters Electrical Specifications Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Key Features: Input • 2W Output Power • 4:1 Input Voltage Range • 1,500 VDC Isolation • Short Circuit Protected • Miniature SIP Case • Single & Dual Outputs • 1.0 MH MTBF • Industry Standard Pin-Out • Low Low Cost!! Parameter Input Voltage Range Conditions Min. Typ. Max. 24 VDC Input 9.0 24.0 36.0 48 VDC Input 18.0 48.0 72.0 Reverse Polarity Input Current Short Circuit Input Power VDC 1.0 A 1,500 mW Output Typ. Max. Units Output Voltage Accuracy Parameter ±1.0 ±3.0 % Output Voltage Balance ±1.0 ±2.0 % Vin = Min to Max ±0.2 ±0.75 % Load Regulation Iout = 10% to 100% ±0.5 ±1.5 % Ripple (20 MHz) See Note 1 15 30 mV P - P 50 150 mV P - P ±0.03 %/°C Max. Units Line Regulation Conditions Min. Noise (20 MHz) Output Power Protection 120 % Temperature Coefficient Output Short Circuit RoHS Compliant Units Continuous (Autorecovery) General Parameter Conditions Isolation Voltage Isolation Resistance Min. 60 Seconds 1,500 500 VDC 1,000 Typ. VDC MΩ Isolation Capacitance 100 kHz, 1V 65 Switching Frequency , Single Output Iout = 100% 100 650 kHz pF Switching Frequency , Dual Output Iout = 100% 200 400 kHz Max. Units Environmental Parameter Conditions Operating Temperature Range Ambient Storage Temperature Range MicroPower Direct 292 Page Street Suite D Stoughton, MA 02072 USA Physical Typ. -40 +25 -55 Cooling Humidity Min. +85 °C +125 °C 95 % Free Air Convection RH, Non-condensing Case Size 1.02 x 0.37 x 0.49 Inches (26.0 x 9.50 x 12.50 mm) Case Material Non-Conductive Black Plastic (UL94-V0) Weight T: (781) 344-8226 F: (781) 344-8481 E: [email protected] W: www.micropowerdirect.com 0.24 Oz (7.0g) Reliability Specifications Parameter MTBF Conditions Min. MIL HDBK 217F, 25°C, Gnd Benign 1.0 Conditions Min. Typ. Max. Units MHours Absolute Maximum Ratings Parameter Input Voltage Surge (1 Sec) Lead Temperature Internal Power Dissipation Typ. Max. 24 VDC Input -0.7 40.0 48 VDC Input -0.7 80.0 1.5 mm From Case For 10 Sec All Models Units VDC 300 °C 1,800 mW Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. Model Selection Guide Model Number D201ERU D202ERU D203ERU D204ERU D205ERU D206ERU D207ERU D208ERU D209ERU D211ERU D212ERU D213ERU D214ERU D215ERU D216ERU D217ERU D218ERU D219ERU Input Output Efficiency Voltage Current Current Voltage (VDC) Current (mA) Nominal Range Full-Load No-Load (VDC) (mA, Max) (mA, Min) (%, Typ) 24 9.0 - 36.0 114 35 3.3 500.0 50.0 73 24 9.0 - 36.0 111 35 5.0 400.0 40.0 75 24 9.0 - 36.0 107 35 9.0 222.0 22.0 78 24 9.0 - 36.0 102 35 12.0 167.0 16.0 82 24 9.0 - 36.0 103 35 15.0 133.0 13.0 81 24 9.0 - 36.0 110 35 ±5.0 ±200.0 ±20.0 76 24 9.0 - 36.0 107 35 ±9.0 ±111.0 ±11.0 78 24 9.0 - 36.0 102 35 ±12.0 ±83.0 ±8.0 82 24 9.0 - 36.0 103 35 ±15.0 ±67.0 ±7.0 81 48 18.0 - 72.0 58 15 3.3 500.0 50.0 72 48 18.0 - 72.0 55 15 5.0 400.0 40.0 76 48 18.0 - 72.0 53 15 9.0 222.0 22.0 78 48 18.0 - 72.0 51 15 12.0 167.0 16.0 81 48 18.0 - 72.0 52 15 15.0 133.0 13.0 80 48 18.0 - 72.0 55 15 ±5.0 ±200.0 ±20.0 75 48 18.0 - 72.0 54 15 ±9.0 ±111.0 ±11.0 77 48 18.0 - 72.0 51 15 ±12.0 ±83.0 ±8.0 81 48 18.0 - 72.0 52 15 ±15.0 ±67.0 ±7.0 80 Notes: 1. When measuring output ripple, it is recommended that an external ceramic capacitor (approx. 1 µF to 10 µF) be placed from the +Vout pin to the -Vout pin for single output units and from each output to common for dual output units. 2. These units should not be operated with a load under 10% of full load. Operation at no-load may cause damage to the unit. 3. These converters are specified for operation without external compoInput Output nents. However, in some applicaVin Capacitor Vout Capacitor tions the addition of input/output capacitors will enhance stability and reduce output ripple. Recommended 12 VDC 100 µF 5 VDC 47 µF capacitor values are given at right. 100 µF 9 VDC 47 µF Output ripple on single output units 15 VDC may be further enhanced by using 24 VDC 10 µF 12 VDC 47 µF the CS terminal (single output units 48 VDC 10 µF 15 VDC 47 µF operated at 50% load or below should use this function). A low ESR capacitor is connected between the CS pin and the -Vout pin (the capcitor anode connected to the -Vout pin). Recommended capacitor values are given in the table at right. If not used, the CS pin should be left open. 4. Dual output units may be connected to provide a 10V, 24V or 30 VDC output. To do this, connect the load across the +Vout and -Vout outputs and float the output common. 5. The remote on/off control pin is referenced to Min Max the -Vin pin. Input current to the pin should <0.6 VDC to Open Circuit be between 5 - 10 mA with a maximum of 20 On mA. Off 2.7 VDC 15.0 VDC 6. It is recommended that a fuse be used on the input of a power supply for protection. See the Model Selection table above for the correct rating. Fuse Rating Slow-Blow (mA) 500 500 500 500 500 500 500 500 500 200 200 200 200 200 200 200 200 200 Derating Curve Mechanical Dimensions Max. Capacitive Load Output Voltage 3.3 5 9 12 820 µF 660 µF 470 µF 330 µF ±5 ±9 ±12 ±15 ±330 µF ±220 µF ±150 µF ±120 µF 15 220 µF Pin Connections Pin Single Dual 1 -Vin -Vin 2 +Vin +Vin 3 Remote ON/OFF 6 +Vout +Vout NC = No Connection Pin 7 8 9 Single NC NC -Vout Dual Common NC -Vout MicroPower Direct Mechanical Notes: Mechanic • All dime dimensions are typical in inches (mm) • Toleranc Tolerance x.xx = ±0.01 (±0.25) www.micropowerdirect.com 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: [email protected]