D200ERW Series Low Cost, Miniature 2W SIP, Wide Input DC/DC Converters Electrical Specifications Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Key Features: • 2W Output Power • 2:1 Input Voltage Range • 1,500 VDC Isolation • Short Circuit Protected • Miniature SIP Case • Single & Dual Outputs • 1.0 MH MTBF • Industry Standard Pin-Out • Low Low Cost!! RoHS Compliant Input Parameter Input Voltage Range Conditions 5 VDC Input 12 VDC Input 24 VDC Input 48 VDC Input Min. 4.5 9.0 18.0 36.0 Typ. 5.0 12.0 24.0 48.0 Reverse Polarity Input Current Short Circuit Input Power Max. 9.0 18.0 36.0 72.0 1.0 1,500 Units Max. ±3.0 ±2.0 ±0.5 ±0.75 ±1.0 100 Units % % % % % mV P - P % %/°C VDC A mW Output Parameter Output Voltage Accuracy Output Voltage Balance Line Regulation Load Regulation , Single Output Load Regulation , Dual Output Ripple & Noise (20 MHz) Output Power Protection Temperature Coefficient Output Short Circuit Conditions Min. Vin = Min to Max Iout = 10% to 100% Iout = 10% to 100% See Note 1 Typ. ±1.0 ±1.0 ±0.2 ±0.5 ±0.5 35 120 ±0.03 Continuous (Autorecovery) General Parameter Isolation Voltage Isolation Resistance Isolation Capacitance Switching Frequency Conditions 60 Seconds 500 VDC 100 kHz, 1V Iout = 100% Min. 1,500 1,000 Typ. Max. 500 Units VDC MΩ pF kHz Max. +85 +125 Units °C °C 95 % 80 180 Environmental Parameter Operating Temperature Range Storage Temperature Range Cooling Humidity MicroPower Direct Conditions Min. Typ. -40 +25 -50 Free Air Convection RH, Non-condensing Ambient Physical 292 Page Street Suite D Stoughton, MA 02072 USA Case Size Case Material Weight T: (781) 344-8226 F: (781) 344-8481 E: [email protected] W: www.micropowerdirect.com Parameter MTBF 0.87 x 0.47 x 0.37 Inches (22.0 x 12.0 x 9.50 mm) Non-Conductive Black Plastic (UL94-V0) 0.19 Oz (5.5g) Reliability Specifications Conditions MIL HDBK 217F, 25°C, Gnd Benign Min. 1.0 Typ. Max. Units MHours Conditions Min. -0.7 -0.7 -0.7 -0.7 Typ. Max. 11.0 22.0 40.0 80.0 300 1,800 Units Absolute Maximum Ratings Parameter Input Voltage Surge (1 Sec) Lead Temperature Internal Power Dissipation 5 VDC Input 12 VDC Input 24 VDC Input 48 VDC Input 1.5 mm From Case For 10 Sec All Models VDC °C mW Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. Model Selection Guide Model Number D201ERW D202ERW D203ERW D204ERW D205ERW D206ERW D207ERW D208ERW D209ERW D211ERW D212ERW D213ERW D214ERW D215ERW D216ERW D217ERW D218ERW D219ERW D221ERW D222ERW D223ERW D224ERW D225ERW D226ERW D227ERW D228ERW D229ERW D231ERW D232ERW D233ERW D234ERW D235ERW D236ERW D237ERW D238ERW D239ERW Input Output Efficiency Voltage Current Current Voltage (VDC) Current (mA) Nominal Range Full-Load No-Load (VDC) (mA, Max) (mA, Min) (%, Typ) 5 4.5 - 9.0 508 40 3.3 500.0 50.0 65 5 4.5 - 9.0 588 40 5.0 400.0 40.0 68 5 4.5 - 9.0 555 40 9.0 222.0 22.0 72 5 4.5 - 9.0 547 40 12.0 166.0 16.0 73 5 4.5 - 9.0 555 40 15.0 133.0 13.0 72 5 4.5 - 9.0 547 40 24.0 83.0 8.0 73 5 4.5 - 9.0 597 40 ±5.0 ±200.0 ±20.0 67 5 4.5 - 9.0 555 40 ±12.0 ±83.0 ±8.0 72 5 4.5 - 9.0 547 40 ±15.0 ±66.0 ±7.0 73 12 9.0 - 18.0 191 20 3.3 500.0 50.0 72 12 9.0 - 18.0 216 20 5.0 400.0 40.0 77 12 9.0 - 18.0 211 20 9.0 222.0 22.0 79 12 9.0 - 18.0 206 20 12.0 166.0 16.0 81 12 9.0 - 18.0 208 20 15.0 133.0 13.0 80 12 9.0 - 18.0 208 20 24.0 83.0 8.0 80 12 9.0 - 18.0 222 20 ±5.0 ±200.0 ±20.0 75 12 9.0 - 18.0 214 20 ±12.0 ±83.0 ±8.0 78 12 9.0 - 18.0 214 20 ±15.0 ±66.0 ±7.0 78 24 18.0 - 36.0 96 10 3.3 500.0 50.0 72 24 18.0 - 36.0 108 10 5.0 400.0 40.0 77 24 18.0 - 36.0 105 10 9.0 222.0 22.0 79 24 18.0 - 36.0 103 10 12.0 166.0 16.0 81 24 18.0 - 36.0 104 10 15.0 133.0 13.0 80 24 18.0 - 36.0 104 10 24.0 83.0 8.0 80 24 18.0 - 36.0 109 10 ±5.0 ±200.0 ±20.0 76 24 18.0 - 36.0 105 10 ±12.0 ±83.0 ±8.0 79 24 18.0 - 36.0 107 10 ±15.0 ±66.0 ±7.0 78 48 36.0 - 72.0 48 5 3.3 500.0 50.0 71 48 36.0 - 72.0 55 5 5.0 400.0 40.0 75 48 36.0 - 72.0 53 5 9.0 222.0 22.0 79 48 36.0 - 72.0 52 5 12.0 166.0 16.0 80 48 36.0 - 72.0 53 5 15.0 133.0 13.0 79 48 36.0 - 72.0 52 5 24.0 83.0 8.0 80 48 36.0 - 72.0 55 5 ±5.0 ±200.0 ±20.0 75 48 36.0 - 72.0 52 5 ±12.0 ±83.0 ±8.0 80 48 36.0 - 72.0 52 5 ±15.0 ±66.0 ±7.0 80 Notes: 1. When measuring output ripple, it is recommended that an external ceramic capacitor (approx. 1 µF to 10 µF) be placed from the +Vout pin to the -Vout pin for single output units and from each output to common for dual output units. Output Capacitor 2. These units should not be operated with a load under Input 10% of full load. Operation at no-load may cause Vin Capacitor Vout 0 - 70ºC -40 - 85ºC damage to the unit. (Electrolitic) (Tantalum) 3. These converters are specified for operation without external components. However, in some applications 5 VDC 100 µF 5 VDC 100 µF 47 µF the addition of input/output capacitors will enhance 12 VDC 100 µF 9 VDC 100 µF 47 µF stability and reduce output ripple. Recommended 24 VDC 10 µF 12 VDC 100 µF 47 µF capacitor values are given at right. Output ripple on single output units may be further 48 VDC 10 µF 15 VDC 100 µF 47 µF enhanced by using the CS terminal (single output units operated at 50% load or below should use this function). A Output Voltage low ESR capacitor is connected between the CS pin and the -Vout 3.3V 5V 9V 12V 15V 24V pin (the capcitor anode connected to the -Vout pin). Recommended capacitor values are given in the table at right. If not used, the CS CS 47 µF - 100 µF 22 µF - 47 µF pin should be left open. 4. Dual output units may be connected to provide a 10V, 24V or 30 VDC output. To do this, connect the load across the +Vout and -Vout outputs and float the output common. 5. The remote on/off control pin is referenced to the -Vin pin. Input current Min Max to the pin should be between 5 - 10 mA with a maximum of 20 mA. <0.6 VDC to Open Circuit 6. It is recommended that a fuse be used on the input of a power supply for On Off 2.7 VDC 15.0 VDC protection. See the Model Selection table above for the correct rating. Fuse Rating Slow-Blow (mA) 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,500 700 700 700 700 700 700 700 700 700 350 350 350 350 350 350 350 350 350 135 135 135 135 135 135 135 135 135 Mechanical Dimensions Derating Curve Mechanical Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.01 (±0.25) Pin Connections Pin Single Dual 1 -Vin -Vin 2 +Vin +Vin 3 Remote ON/OFF 5 NF NF NF = No Function Pin 6 7 8 Single +Vout -Vout CS Dual +Vout Common -Vout MicroPower Direct www.micropowerdirect.com 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: [email protected]