D200I Series High Isolation Miniature, 2W SIP DC/DC Converters Electrical Specifications Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Input Key Features: Parameter ● 2W Output Power ● 3,000 VDC Isolation Input Voltage Range ● Miniature SIP Case ● Single & Dual Outputs Input Filter ● >2 MHour MTBF Reverse Polarity Input Current Output ● 28 Standard Models ● Industry Standard Pin-Out Parameter Output Voltage Accuracy Output Voltage Balance Line Regulation Load Regulation (Note 1) Ripple & Noise (20 MHz) (Note 2) Output Power Protection Temperature Coefficient Output Short Circuit Conditions Typ. Max. Units 5 VDC Input 4.5 5.0 12 VDC Input 10.8 12.0 24 VDC Input 21.6 24.0 48 VDC Input 42.0 48.0 Internal Capacitor Min. 5.5 13.2 26.4 52.0 VDC 0.3 A Typ. Max. Units ±1.0 ±3.0 ±1.0 % % % 75 ±0.02 mV P - P % %/ºC Max. Units Conditions Min. Dual Output , Balanced Loads For Vin Change of 1% ±1.2 See Model Selection Guide 120 Momentary (0.5 Sec.) General Parameter Conditions Isolation Voltage Isolation Resistance Isolation Capacitance Switching Frequency Min. 60 Seconds 500 VDC 100 kHz, 1V Typ. 3,000 1,000 VDC MΩ pF kHz 60 125 Environmental Parameter Operating Temperature Range Operating Temperature Range Storage Temperature Range Cooling Humidity Conditions Ambient Case Min. Typ. Max. Units -40 +25 +85 +100 +125 ºC ºC ºC 95 % -40 Free Air Convection RH, Non-condensing Physical MicroPower Direct 232 Tosca Drive Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: [email protected] W: www.micropowerdirect.com Case Size (5V, 12V & 24V Input Models) Case Size (48V Input Models) Case Material Weight 0.76 x 0.24 x 0.37 Inches (19.5 x 6.0 x 9.5 mm) 0.76 x 0.28 x 0.37 Inches (19.5 x 7.2 x 9.5 mm) Non-Conductive Black Plastic (UL94-V0) 0.09 Oz (2.7g) Reliability Specifications Parameter MTBF Conditions MIL HDBK 217F, 25ºC, Gnd Benign Min. Typ. Max. 2.0 Units MHours Absolute Maximum Ratings Parameter Input Voltage Surge (1 Sec) Lead Temperature Internal Power Dissipation Conditions 5 VDC Input 12 VDC Input 24 VDC Input 48 VDC Input 1.5 mm From Case For 10 Sec All Models Min. -0.7 -0.7 -0.7 -0.7 Typ. Max. 9.0 18.0 30.0 55.0 260 650 Units VDC ºC mW Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. Model Selection Guide Model Number D201I D202I D203I D204I D205I D206I D207I D211I D212I D213I D214I D215I D216I D217I D221I D222I D223I D224I D225I D226I D227I D231I D232I D233I D234I D235I D236I D237I Input Output Load Fuse Rating Efficiency Voltage (VDC) Current (mA) Slow-Blow Voltage Current Current Regulation (%, Typ) (%, Max) (mA) Nominal Range Full-Load No-Load (VDC) (mA, Max) (mA, Min) 5 4.5 - 5.5 533 35 3.3 400.0 10.0 12 75 1,000 5 4.5 - 5.5 513 35 5.0 400.0 8.0 12 78 1,000 5 4.5 - 5.5 495 35 12.0 165.0 3.0 8 80 1,000 5 4.5 - 5.5 499 35 15.0 133.0 2.5 8 80 1,000 5 4.5 - 5.5 533 35 ±5.0 ±200.0 ±4.0 12 75 1,000 5 4.5 - 5.5 504 35 ±12.0 ±83.0 ±1.5 8 79 1,000 5 4.5 - 5.5 501 35 ±15.0 ±66.0 ±1.0 8 79 1,000 12 10.8 - 13.2 204 25 3.3 400.0 10.0 8 67 500 12 10.8 - 13.2 212 25 5.0 400.0 8.0 8 78 500 12 10.8 - 13.2 196 25 12.0 165.0 3.0 8 85 500 12 10.8 - 13.2 200 25 15.0 133.0 2.5 8 83 500 12 10.8 - 13.2 216 25 ±5.0 ±200.0 ±4.0 8 77 500 12 10.8 - 13.2 201 25 ±12.0 ±83.0 ±1.5 8 82 500 12 10.8 - 13.2 200 25 ±15.0 ±66.0 ±1.0 8 82 500 24 21.6 - 26.4 92 10 3.3 400.0 10.0 8 74 200 24 21.6 - 26.4 108 10 5.0 400.0 8.0 8 77 200 24 21.6 - 26.4 101 10 12.0 165.0 3.0 8 81 200 24 21.6 - 26.4 101 10 15.0 133.0 2.5 8 82 200 24 21.6 - 26.4 108 10 ±5.0 ±200.0 ±4.0 8 77 200 24 21.6 - 26.4 102 10 ±12.0 ±83.0 ±1.5 8 81 200 24 21.6 - 26.4 99 10 ±15.0 ±66.0 ±1.0 8 84 200 48 42.0 - 52.0 59 10 3.3 400.0 10.0 8 70 100 48 42.0 - 52.0 54 10 5.0 400.0 8.0 8 77 100 48 42.0 - 52.0 51 10 12.0 165.0 3.0 8 81 100 48 42.0 - 52.0 50 10 15.0 133.0 2.5 8 82 100 48 42.0 - 52.0 54 10 ±5.0 ±200.0 ±4.0 8 76 100 48 42.0 - 52.0 51 10 ±12.0 ±83.0 ±1.5 8 81 100 48 42.0 - 52.0 50 10 ±15.0 ±66.0 ±1.0 8 82 100 Notes: 1. Output load regulation is specified for a load change of 20% to 100%. 2. When measuring output ripple, it is recommended that an external ceramic capacitor (approx 10 µF) be placed from the +Vout pin to the -Vout pin for single output units and from each output to common for dual output units. 3. All 3.3, 5 and ±5 VDC output models may be operated to +85ºC ambient with an unobstructed airflow of 3.6 ft/S (1.1 m/S). 4. The 5V, 12V and 24V input units do not require external components to operate, but the use of an input capacitor (10 µF) may enhance performance in some applications. An output capacitor (1.0 µF to 10 µF) may be used to reduce ripple. The 48V input models require an input capacitor of 4.7 uF to 47 uF (dependent upon the application). 5. Dual output units may be connected to provide a 10V, 24V or 30 VDC output. To do this, connect the load across the positive (+Vout) and negative (-Vout) outputs and float the output common. 6. It is recommended that a fuse be used on the input of a power supply for protection. See the table above for the correct rating. Derating Curve Pin Connections Pin Single Dual 1 2 5 6 7 +Vin -Vin -Vout No Pin +Vout +Vin -Vin -Vout Common +Vout Mechanical Dimensions Capacitive Load Single Output (μF Max) 470 Dual Output (μF Max) ±390 Notes: All dimensions are typical in inches (mm) Tolerance x.xx = ±0.01 (±0.25) Pin 1 is marked by a “dot” or indentation on the side of the unit MicroPower Direct www.micropowerdirect.com 232 Tosca Drive Stoughton, MA 02072 ■ TEL: (781) 344-8226 ■ FAX: (781) 344-8481 ■ E-Mail: [email protected]