D200I Series High Isolation Miniature, 2W SIP DC/DC Converters Electrical Specifications Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Key Features: • 2W Output Power Input Parameter • Miniature SIP Case • Single & Dual Outputs Input Voltage Range • 3,000 VDC Isolation • >1.12 MHour MTBF • 28 Standard Models • Industry Standard Pin-Out RoHS Compliant Input Filter Reflected Ripple Current Conditions Min. 5 VDC Input 4.5 12 VDC Input 10.8 24 VDC Input 21.6 48 VDC Input 43.2 Internal Capacitor 12 μH Source Inductance Typ. Max. Units 5.0 12.0 24.0 48.0 5.5 13.2 26.4 52.8 VDC 20 mA P - P Output Parameter Output Voltage Accuracy Output Voltage Balance Line Regulation Load Regulation Ripple & Noise (20 MHz) Output Power Protection Temperature Coefficient Output Short Circuit Conditions Min. Typ. Max. ±3.0 Dual Output , Balanced Loads ±1.0 For Vin Change of 1% ±1.2 See Model Selection Guide 75 120 Units % % % ±0.02 mV P - P % %/ºC Max. Units Momentary (0.5 Sec.) General Parameter Conditions Isolation Voltage Isolation Resistance Isolation Capacitance Switching Frequency Min. 60 Seconds 500 VDC 100 kHz, 1V Typ. 3,000 1,000 VDC MΩ pF kHz 60 80 Environmental Parameter Operating Temperature Range Operating Temperature Range Storage Temperature Range Cooling Humidity MicroPower Direct 292 Page Street Suite D Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: [email protected] W: www.micropowerdirect.com Conditions Ambient Case Min. Typ. Max. Units -40 +25 +85 +100 +125 ºC ºC ºC 95 % -40 Free Air Convection RH, Non-condensing Physical Case Size (5V, 12V & 24V Input Models) Case Size (48V Input Models) Case Material Weight 0.76 x 0.24 x 0.39 Inches (19.5 x 6.0 x 10.0 mm) 0.76 x 0.28 x 0.39 Inches (19.5 x 7.2 x 10.0 mm) Non-Conductive Black Plastic (UL94-V0) 0.08 Oz (2.3g) Reliability Specifications Parameter MTBF Conditions MIL HDBK 217F, 25ºC, Gnd Benign Min. Typ. Max. 1.12 Units MHours Absolute Maximum Ratings Parameter Input Voltage Surge (1 Sec) Lead Temperature Internal Power Dissipation Conditions 5 VDC Input 12 VDC Input 24 VDC Input 48 VDC Input 1.5 mm From Case For 10 Sec All Models Min. -0.7 -0.7 -0.7 -0.7 Typ. Max. 7.0 15.0 28.0 54.0 260 650 Units VDC ºC mW Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. Model Selection Guide Model Number D201I D202I D203I D204I D205I D206I D207I D211I D212I D213I D214I D215I D216I D217I D221I D222I D223I D224I D225I D226I D227I D231I D232I D233I D234I D235I D236I D237I Input Output Load Voltage (VDC) Current (mA) Regulation Voltage Current Current Nominal Range Full-Load No-Load (VDC) (mA, Max) (mA, Min) (%, Max) 5 4.5 - 5.5 367 30 3.3 400.0 10.0 20 5 4.5 - 5.5 512 30 5.0 400.0 8.0 10 5 4.5 - 5.5 500 30 12.0 165.0 3.5 10 5 4.5 - 5.5 500 30 15.0 133.0 2.7 10 5 4.5 - 5.5 555 30 ±5.0 ±200.0 ±4.0 10 5 4.5 - 5.5 512 30 ±12.0 ±83.3 ±1.7 10 5 4.5 - 5.5 500 30 ±15.0 ±66.6 ±1.4 10 12 10.8 - 13.2 169 20 3.3 400.0 10.0 20 12 10.8 - 13.2 216 20 5.0 400.0 8.0 10 12 10.8 - 13.2 203 20 12.0 165.0 3.5 10 12 10.8 - 13.2 203 20 15.0 133.0 2.7 10 12 10.8 - 13.2 222 20 ±5.0 ±200.0 ±4.0 10 12 10.8 - 13.2 203 20 ±12.0 ±83.3 ±1.7 10 12 10.8 - 13.2 203 20 ±15.0 ±66.6 ±1.4 10 24 21.6 - 26.4 76 10 3.3 400.0 10.0 20 24 21.6 - 26.4 105 10 5.0 400.0 8.0 10 24 21.6 - 26.4 102 10 12.0 165.0 3.5 10 24 21.6 - 26.4 101 10 15.0 133.0 2.7 10 24 21.6 - 26.4 111 10 ±5.0 ±200.0 ±4.0 10 24 21.6 - 26.4 101 10 ±12.0 ±83.3 ±1.7 10 24 21.6 - 26.4 101 10 ±15.0 ±66.6 ±1.4 10 48 43.2 - 52.8 45 6 3.3 400.0 10.0 20 48 43.2 - 52.8 54 6 5.0 400.0 8.0 10 48 43.2 - 52.8 53 6 12.0 165.0 3.5 10 48 43.2 - 52.8 53 6 15.0 133.0 2.7 10 48 43.2 - 52.8 57 6 ±5.0 ±200.0 ±4.0 10 48 43.2 - 52.8 52 6 ±12.0 ±83.3 ±1.7 10 48 43.2 - 52.8 52 6 ±15.0 ±66.6 ±1.4 10 72 78 82 82 72 78 80 65 77 82 82 75 82 82 72 79 80 82 75 82 82 60 77 78 78 73 80 80 Pin Connections Capacitive Load Other input/output combinations are available (i.e. 24.0 VDC). Contact the factory for details at: [email protected] Single Output (μF Max) Dual Output (μF Max) 470 ±220 Notes: 1. Output load regulation is specified for a load change of 20% to 100%. 2. These units do not require external components to operate, but the use of an input capacitor (10 μF) may enhance performance in some applications. It is recommended that an input capacitor of 4.7 uF to 47 uF (dependent upon the application) be used on 48V input model. An output capacitor (4.7 μF to 220 μF or ±4.7 μF to ±100 μF) may be used to reduce ripple. To improve EMI performance, a simple filter network consisting of a 10 uF to 100 uF capacitor and 12 uH inductor should be effective. 3. These units will operate at no load without damage, but may not meet all specifications. 4. Dual output units may be connected to provide a 10V, 24V or 30 VDC output. To do this, connect the load across the positive (+Vout) and negative (-Vout) outputs and float the output common. 5. It is recommended that a fuse be used on the input of a power supply for protection. See the table above for the correct rating. Fuse Rating Slow-Blow (mA) 1,000 1,000 1,000 1,000 1,000 1,000 1,000 500 500 500 500 500 500 500 200 200 200 200 200 200 200 100 100 100 100 100 100 100 Efficiency (%, Typ) Pin Single Dual 1 2 5 6 7 +Vin -Vin -Vout No Pin +Vout +Vin -Vin -Vout Common +Vout Mechanical Dimensions Derating Curve MicroPower Direct www.micropowerdirect.com 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • Notes: • All dimensio dimensions are typical in inches (mm) • Tolerance xx.xx = ±0.01 (±0.25) marked by a “dot” or indentation • Pin 1 is mar on the side of the unit FAX: (781) 344-8481 • E-Mail: [email protected]