DG401, DG403 ® Data Sheet November 20, 2006 FN3284.11 Monolithic CMOS Analog Switches Features The DG401 and DG403 monolithic CMOS analog switches have TTL and CMOS compatible digital inputs. • ON Resistance (Max) . . . . . . . . . . . . . . . . . . . . . . . . . 45Ω These switches feature low analog ON resistance (<45Ω) and fast switch time (tON<150ns). Low charge injection simplifies sample and hold applications. • Fast Switching Action - tON (Max) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150ns - tOFF (Max) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100ns The improvements in the DG401, DG403 series are made possible by using a high voltage silicon-gate process. An epitaxial layer prevents the latch-up associated with older CMOS technologies. The 44V maximum voltage range permits controlling 30VP-P signals. Power supplies may be single-ended from +5V to +34V, or split from ±5V to ±17V. • Low Charge Injection The analog switches are bilateral, equally matched for AC or bidirectional signals. The ON resistance variation with analog signals is quite low over a ±15V analog input range. The three different devices provide the equivalent of two SPST (DG401) or two SPDT (DG403) relay switch contacts with CMOS or TTL level activation. The pinout is similar, permitting a standard layout to be used, choosing the switch function as needed. • Pb-Free Plus Anneal Available (RoHS Compliant) • Low Power Consumption (PD) . . . . . . . . . . . . . . . . . . .<35μW • DG401 Dual SPST; Same Pinout as HI-5041 • DG403 Dual SPDT; DG190, IH5043, IH5151, HI-5051 • TTL, CMOS Compatible • Single or Split Supply Operation Applications • Audio Switching • Battery Operated Systems • Data Acquisition • Hi-Rel Systems • Sample and Hold Circuits Pinouts DG401 (16 LD SOIC, TSSOP) TOP VIEW • Communication Systems • Automatic Test Equipment Ordering Information D1 1 16 S1 NC 2 15 IN1 NC 3 14 V- NC 4 13 GND DG401DY* DG401DY -40 to +85 16 Ld SOIC M16.15 NC 5 12 VL -40 to +85 16 Ld SOIC (Pb-free) M16.15 11 V+ DG401DYZ* (Note) DG401DYZ NC 6 NC 7 10 IN2 DG401 DVZ -40 to +85 D2 8 9 S2 DG401DVZ* (Note) 16 Ld TSSOP M16.173 (Pb-free) DG403DY* DG403DY -40 to +85 16 Ld SOIC M16.15 DG403DYZ* (Note) DG403DYZ -40 to +85 16 Ld SOIC (Pb-free) M16.15 DG403DVZ* (Note) DG403 DVZ -40 to +85 16 Ld TSSOP M16.173 (Pb-free) DG403 (16 LD SOIC, TSSOP) TOP VIEW PART NUMBER* PART TEMP. MARKING RANGE (°C) PACKAGE PKG. DWG. # D1 1 16 S1 *Add “-T” suffix for tape and reel. NC 2 15 IN1 D3 3 14 V- S3 4 13 GND S4 5 12 VL NOTE: Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. D4 6 11 V+ NC 7 10 IN2 D2 8 9 S2 NOTE: (NC) No Connection. 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright © Intersil Americas Inc. 1999, 2002-2004, 2006. All Rights Reserved All other trademarks mentioned are the property of their respective owners. TRUTH TABLE DG401 DG403 LOGIC SWITCH SWITCH 1, 2 SWITCH 3, 4 0 OFF OFF ON 1 ON ON OFF NOTE: Logic “0” ≤0.8V. Logic “1” ≥2.4V. Functional Diagrams DG401 VL DG403 V+ 12 S1 VL 11 16 12 1 S1 D1 S3 IN1 15 IN2 S2 V+ 11 16 1 4 3 D1 D3 IN1 15 10 IN2 9 8 D2 S2 S4 13 14 GND 10 9 8 5 6 13 V- GND D2 D4 14 V- SWITCHES SHOWN FOR LOGIC “1” INPUT Schematic Diagram V+ SOURCE VVL VIN V+ GND DRAIN V- 2 FN3284.11 November 20, 2006 Absolute Maximum Ratings Thermal Information V+ to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44.0V GND to V-. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25V VL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (GND - 0.3V) to (V+) +0.3V Digital Inputs VS , VD (Note 1) . . . . . (V-) -2V to (V+) + 2V or 30mA, Whichever Occurs First Continuous Current (Any Terminal) . . . . . . . . . . . . . . . . . . . . . 30mA Peak Current, S or D (Pulsed 1ms, 10% Duty Cycle, Max) . . 100mA Thermal Resistance (Typical, Note 2) θJA (°C/W) SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 TSSOP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 Maximum Junction Temperature (Plastic Package). . . . . . . . +150°C Maximum Storage Temperature Range . . . . . . . . . . . . -65°C to +150°C Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . +300°C (SOIC and TSSOP- Lead Tips Only) Operating Conditions Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C Voltage Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20V (Max) Input Low Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.8V (Max) Input High Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4V (Min) Input Rise and Fall Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . ≤20ns CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 1. Signals on SX , DX , or INX exceeding V+ or V- will be clamped by internal diodes. Limit forward diode current to maximum current ratings. 2. θJA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details. Electrical Specifications Test Conditions: V+ = +15V, V- = -15V, VIN = 2.4V, 0.8V (Note 3), VL = 5V, Unless Otherwise Specified PARAMETER TEST CONDITIONS TEMP (°C) (NOTE 4) MIN (NOTE 5) TYP (NOTE 4) MAX +25 - 100 150 ns +25 - 60 100 ns UNITS DYNAMIC CHARACTERISTICS RL = 300Ω, CL = 35pF Turn-ON Time, tON Turn-OFF Time, tOFF Break-Before-Make Time Delay (DG403), tD RL = 300Ω, CL = 35pF +25 5 12 - ns Charge Injection, Q (Figure 3) CL = 10nF, VG = 0V, RG = 0Ω +25 - 60 - pC OFF Isolation (Figure 4) RL = 100Ω, CL = 5pF, f = 1MHz +25 - 72 - dB +25 - -90 - dB +25 - 12 - pF Drain OFF Capacitance, CD(OFF) +25 - 12 - pF Channel ON Capacitance, CD(ON) + CS(ON) +25 - 39 - pF Crosstalk (Channel-to-Channel) (Figure 6) Source OFF Capacitance, CS(OFF) f = 1MHz, VS = VD = 0V (Figure 7) DIGITAL INPUT CHARACTERISTICS Input Current with VIN Low, IIL VIN Under Test = 0.8V, All Others = 2.4V Full -1 0.005 1 μA Input Current with VIN High, IIH VIN Under Test = 2.4V, All Others = 0.8V Full -1 0.005 1 μA Full -15 - 15 V +25 - 20 45 Ω ANALOG SWITCH CHARACTERISTICS Analog Signal Range, VANALOG Drain-Source ON Resistance, rDS(ON) V+ = 13.5V, V- = -13.5V, IS = 10mA, VD = ±10V Full - - 55 Ω rDS(ON) Matching Between Channels, ΔrDS(ON) V+ = 16.5V, V- = -16.5V, IS = -10mA, VD = 5, 0, -5V +25 - 3 3 Ω Full - - 5 Ω V+ = 16.5V, V- = -16.5 VD = ±15.5V, VS = 15.5V +25 -0.5 -0.01 0.5 nA Full -5 - 5 nA +25 -0.5 -0.01 0.5 nA Full -5 - 5 nA +25 -1 -0.04 1 nA Full -10 - 10 nA Source OFF Leakage Current, IS(OFF) Drain OFF Leakage Current, ID(OFF) Channel ON Leakage Current, ID(ON) + IS(ON) 3 V± = ±16.5V, VD = VS = ±15.5V FN3284.11 November 20, 2006 Electrical Specifications Test Conditions: V+ = +15V, V- = -15V, VIN = 2.4V, 0.8V (Note 3), VL = 5V, Unless Otherwise Specified (Continued) PARAMETER TEST CONDITIONS TEMP (°C) (NOTE 4) MIN (NOTE 5) TYP (NOTE 4) MAX +25 - 0.01 1 μA Full - - 5 μA +25 -1 -0.01 - μA Full -5 - - μA +25 - 0.01 1 μA Full - - 5 μA +25 -1 -0.01 - μA Full -5 - - μA UNITS POWER SUPPLY CHARACTERISTICS Positive Supply Current, I+ V+ = 16.5V, V- = -16.5V, VIN = 0V or 5V Negative Supply Current, I- Logic Supply Current, IL Ground Current, IGND NOTES: 3. VIN = input voltage to perform proper function. 4. The algebraic convention whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet. 5. Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing. Test Circuits and Waveforms 3V LOGIC INPUT tr < 20ns tf < 20ns 50% VL 0V tOFF SWITCH INPUT SWITCH INPUT VS +15V RL = 300Ω CL = 35pF V+ VO D1 S1 IN1 VO SWITCH OUTPUT 5V 90% 90% RL LOGIC INPUT 0V GND tON CL V- 10% SWITCH INPUT -VS (NOTE 7) 0V NOTES: 6. Logic input waveform is inverted for switches that have the opposite logic sense. 7. VS = 10V for tON , VS = -10V for tOFF. -15V Repeat test for IN2 and S2. For load conditions, see Specifications. CL includes fixture and stray capacitance. RL V O = V S -----------------------------------R L + r DS ( ON ) FIGURE 1B. TEST CIRCUIT FIGURE 1A. MEASUREMENT POINTS FIGURE 1. SWITCHING TIMES 4 FN3284.11 November 20, 2006 Test Circuits and Waveforms (Continued) 5V 3V LOGIC INPUT +15V VL RL = 300Ω CL = 35pF V+ 0V SWITCH OUTPUT (VO1) D2 VS2 = 10V 90% VO1 D1 VS1 = 10V VS1 VO2 GND 90% V- 0V tD tD CL2 RL2 LOGIC INPUT VS2 0V CL1 IN1 0V SWITCH OUTPUT (VO2) RL1 -15V CL includes fixture and stray capacitance. FIGURE 2B. TEST CIRCUIT FIGURE 2A. MEASUREMENT POINTS FIGURE 2. BREAK-BEFORE-MAKE TIME 5V +15V VL SWITCH OUTPUT VO ΔVO ON INX V+ RG VO VG ON OFF D1 CL V- GND Q = ΔVO x CL 0V FIGURE 3A. MEASUREMENT POINTS -15V FIGURE 3B. TEST CIRCUIT FIGURE 3. CHARGE INJECTION C SIGNAL GENERATOR V+ +15V +5V VL C C SIGNAL GENERATOR VS INX RL GND C -15V FIGURE 4. OFF ISOLATION TEST CIRCUIT 5 +5V VL C VS INX 0V, 2.4V VD ANALYZER V- +15V 0V, 2.4V VD ANALYZER V+ RL GND V- C -15V FIGURE 5. INSERTION LOSS TEST CIRCUIT FN3284.11 November 20, 2006 Test Circuits and Waveforms V+ C (Continued) +5V +15V VL C +15V C SIGNAL GENERATOR VS1 +5V V+ VL C 50Ω VD1 VS IN1 0V, 2.4V IN2 0V, 2.4V AS REQUIRED IMPEDANCE ANALYZER VS2 VD2 ANALYZER INX 0V, 2.4V VD NC C RL V- GND -15V C V- GND -15V FIGURE 7. CAPACITANCES TEST CIRCUIT FIGURE 6. CROSSTALK TEST CIRCUIT Application Information Dual Slope Integrators Peak Detector The DG403 is well suited to configure a selectable slope integrator. One control signal selects the timing capacitor C1 or C2 . Another one selects eIN or discharges the capacitor in preparation for the next integration cycle. A3 acting as a comparator provides the logic drive for operating SW1 . The output of A2 is fed back to A3 and compared to the analog input eIN . If eIN > eOUT the output of A3 is high keeping SW1 closed. This allows C1 to charge up to the analog input voltage. When eIN goes below eOUT, A3 goes negative, turning SW1 off. The system will therefore store the most positive analog input experienced. +5V +15V VL eIN V+ S1 D1 S3 D2 eOUT RESET SW2 IN1 TTL INTEGRATE/ RESET S2 D3 S4 D4 C1 + SW1 DG403 V- A2 eOUT C1 C2 GND R1 + - eIN IN2 SCOPE SELECT A1 + A3 DG401 -15V FIGURE 8. DUAL SLOPE INTEGRATOR 6 FIGURE 9. POSITIVE PEAK DETECTOR FN3284.11 November 20, 2006 Typical Performance Curves 10 4 V+ = 15V V- = -15V TA = 20°C 8 VL = 5V TA = 25°C 3 VT (V) VT (V) 6 DG403 SW3, 4 4 2 1 2 0 0 0 2 4 6 8 10 12 VL (V) 14 16 18 20 0 2 4 6 8 10 12 14 SUPPLY VOLTAGE (±V) 16 18 20 FIGURE 11. INPUT SWITCHING THRESHOLD vs POWER SUPPLY VOLTAGE FIGURE 10. INPUT SWITCHING THRESHOLD vs LOGIC SUPPLY VOLTAGE 60 40 V+ = 15V V- = -15V VL = 5V 35 TA = 25°C 50 125°C rDS(ON) (Ω) rDS(ON) (Ω) 30 25 85°C 20 25°C 15 -40°C 40 V+ = 12V, V- = -12V V+ = 15V, V- = -15V V+ = 20V, V- = -20V V+ = 6V, V- = -6V V+ = 10V, V- = -10V V+ = 22V, V- = -22V 30 0°C 20 -55°C 10 -15 10 -10 -5 0 VD (V) 5 10 15 -25 -15 5 15 25 VD (V) FIGURE 13. rDS(ON) vs VD AND POWER SUPPLY VOLTAGE FIGURE 12. rDS(ON) vs VD AND TEMPERATURE 70 200 V- = 0V TA = 25°C V+ = 15V V- = -15V VL = 5V 180 60 160 V+ = 7.5V CL = 10nF 140 50 120 V+ = 10V Q (pC) rDS(ON) (Ω) -5 40 V+ = 12V 80 V+ = 15V 30 60 V+ = 20V 40 V+ = 22V 20 CL = 1nF 100 CL = 100pF 20 0 10 0 5 10 15 20 25 VD (V) FIGURE 14. rDS(ON) vs VD AND SINGLE SUPPLY VOLTAGE 7 -15 -10 -5 0 5 10 15 VS (V) FIGURE 15. CHARGE INJECTION vs SOURCE VOLTAGE FN3284.11 November 20, 2006 Typical Performance Curves (Continued) 0.0 100.0 -0.5 10.0 1.0 IS(OFF) (nA) LOSS (dB) RL = 600Ω -1.0 RL = 75Ω -1.5 RL = 50Ω V+ = 15V, V- = -15V VL = 5V, VS = 1VRMS SEE INSERTION LOSS TEST SETUP (FIGURE 5) -2.0 V+ = 15V V- = -15V VL = 5V VD = ±14V TYPICAL 0.1 0.01 0.001 0.0001 10K 100K 1M FREQUENCY (Hz) -55 -35 10M 10.0 ID(ON) + IS(ON) (nA) ID(OFF) (nA) 100.0 1.0 TYPICAL 0.1 0.01 0.001 65 85 105 125 105 125 V+ = 15V V- = -15V VL = 5V VD = ±14V 1.0 TYPICAL 0.1 0.01 0.0001 -55 -35 -15 5 25 45 65 85 105 -55 -35 125 -15 5 25 45 65 85 TEMPERATURE (°C) TEMPERATURE (°C) FIGURE 18. ID(OFF) vs TEMPERATURE 60 45 0.001 0.0001 90 25 FIGURE 17. IS(OFF) vs TEMPERATURE V+ = 15V V- = -15V VL = 5V VD = ±14V 10.0 5 TEMPERATURE (°C) FIGURE 16. INSERTION LOSS vs FREQUENCY 100.0 -15 FIGURE 19. ID(ON) + IS(ON) vs TEMPERATURE 10.0 WHEN VANALOG EXCEEDS POWER SUPPLY, SWITCH SUBSTRATE DIODES BEGIN TO CONDUCT 1.0 I+ V+ = 15V V- = -15V VL = 5V IL 0 I+, I -, IL , (μA) IS , ID (pA) 30 ID(OFF) , IS(OFF) -30 ID(ON) + IS(ON) -60 I0.1 0.01 V+ = 15V, V- = -15V -90 VL = 5V, TA = 25°C ID(OFF) , VS = 0V IS(OFF) , VD = 0V -120 -150 -20 -15 -10 -5 0 VS , VD (V) 5 10 15 20 FIGURE 20. LEAKAGE CURRENTS vs ANALOG VOLTAGE 8 0.001 IL I0.0001 -55 -35 -15 5 25 45 65 85 105 125 TEMPERATURE (°C) FIGURE 21. SUPPLY CURRENT vs TEMPERATURE FN3284.11 November 20, 2006 Typical Performance Curves (Continued) 20 40 V+ = 15V V- = -15V VL = 5V 10 30 VS (V) 5 0 NOT MEASURABLE DUE TO CAPACITIVE FEEDTHROUGH -5 VL = 5V 35 tON , tOFF (ns) 15 -10 VS = 10V 25 20 VS = -10V 15 10 -20 5 SEE BBM TEST SETUP (FIGURE 2) SEE BBM TEST SETUP (FIGURE 2) 0 -15 0 10 20 30 40 50 0 5 BREAK-BEFORE-MAKE TIME (ns) 600 240 V+ = 15V V- = -15V VL = 5V 480 tON , tOFF (ns) tON , tOFF (ns) 300 240 tON , VS = 10V tON , VS = -10V tON , VS = 10V 150 120 tOFF , VS = -10V 90 tON , VS = -10V 60 tOFF, VS = 10V tOFF, VS = 10V 30 60 tOFF, VS = -10V 0 0 1 2 3 0 4 5 -55 -35 6 -15 VIN (V) 200 140 VL = 5V tON , tOFF (ns) 100 VS = -5V tOFF 80 V- = 0V 270 VS = 5V tOFF 120 45 65 85 105 125 FIGURE 25. SWITCHING TIME vs TEMPERATURE (NOTE 8) VS = -5V tON 160 25 300 VS = 5V tON 180 5 TEMPERATURE (°C) FIGURE 24. SWITCHING TIME vs INPUT LOGIC VOLTAGE (NOTE 8) tON , tOFF (ns) 25 180 360 120 20 V+ = 15V V- = -15V VL = 5V 210 420 180 15 FIGURE 23. BREAK-BEFORE-MAKE vs POWER SUPPLY VOLTAGE FIGURE 22. BREAK-BEFORE-MAKE vs ANALOG VOLTAGE 540 10 SUPPLY VOLTAGE (±V) 240 V- = -5V 210 V+V-= =-15V -15 VS = 5V tON 180 tON V- = -15V 150 tON 120 60 90 40 60 20 30 V- = 0V V- = -5V V- = 0V tOFF 0 0 0 5 10 15 SUPPLY VOLTAGE (±V) 20 25 FIGURE 26. SWITCHING TIME vs POWER SUPPLY VOLTAGE (NOTE 8) 9 0 5 10 15 20 25 POSITIVE SUPPLY (V) FIGURE 27. SWITCHING TIME vs POSITIVE SUPPLY VOLTAGE (NOTE 8) FN3284.11 November 20, 2006 Typical Performance Curves (Continued) 300 VS = -5V 270 240 tON , tOFF (ns) 210 180 V- = -5V 150 V- = -15V tON 120 V- = -15V tON 90 tOFF V- = -5V 60 tOFF 30 0 0 5 10 15 20 25 POSITIVE SUPPLY (V) FIGURE 28. SWITCHING TIME vs POSITIVE SUPPLY VOLTAGE (NOTE 8) NOTE: 8. Refer to Figure 1 for test conditions. 10 FN3284.11 November 20, 2006 Thin Shrink Small Outline Plastic Packages (TSSOP) M16.173 N 16 LEAD THIN SHRINK SMALL OUTLINE PLASTIC PACKAGE INDEX AREA E 0.25(0.010) M 2 INCHES E1 GAUGE PLANE -B1 B M L 0.05(0.002) -A- SYMBOL MIN MAX MIN MAX NOTES A - 0.043 - 1.10 - A1 3 A D -C- e α c 0.10(0.004) C A M 0.05 0.15 - A2 0.033 0.037 0.85 0.95 - b 0.0075 0.012 0.19 0.30 9 c 0.0035 0.008 0.09 0.20 - B S 0.002 D 0.193 0.201 4.90 5.10 3 0.169 0.177 4.30 4.50 4 0.026 BSC E 0.246 L 0.020 N α NOTES: 1. These package dimensions are within allowable dimensions of JEDEC MO-153-AB, Issue E. 0.006 E1 e A2 A1 b 0.10(0.004) M 0.25 0.010 SEATING PLANE MILLIMETERS 0.65 BSC 0.256 6.25 0.028 0.50 16 0° - 6.50 - 0.70 6 16 8° 0° 7 8° Rev. 1 2/02 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Dimension “D” does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension “E1” does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.15mm (0.006 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. “L” is the length of terminal for soldering to a substrate. 7. “N” is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. Dimension “b” does not include dambar protrusion. Allowable dambar protrusion shall be 0.08mm (0.003 inch) total in excess of “b” dimension at maximum material condition. Minimum space between protrusion and adjacent lead is 0.07mm (0.0027 inch). 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. (Angles in degrees) 11 FN3284.11 November 20, 2006 Small Outline Plastic Packages (SOIC) M16.15 (JEDEC MS-012-AC ISSUE C) N INDEX AREA H 0.25(0.010) M 16 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE B M INCHES E -B1 2 3 L SEATING PLANE -A- A D h x 45° -C- e A1 B C 0.10(0.004) 0.25(0.010) M C A M SYMBOL MIN MAX MIN MAX NOTES A 0.0532 0.0688 1.35 1.75 - A1 0.0040 0.0098 0.10 0.25 - B 0.013 0.020 0.33 0.51 9 C 0.0075 0.0098 0.19 0.25 - D 0.3859 0.3937 9.80 10.00 3 E 0.1497 0.1574 3.80 4.00 4 e α B S 0.050 BSC 1.27 BSC - H 0.2284 0.2440 5.80 6.20 - h 0.0099 0.0196 0.25 0.50 5 L 0.016 0.050 0.40 1.27 6 N α NOTES: MILLIMETERS 16 0° 16 8° 0° 7 8° 1. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of Publication Number 95. Rev. 1 6/05 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Dimension “D” does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension “E” does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. “L” is the length of terminal for soldering to a substrate. 7. “N” is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. The lead width “B”, as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch). 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 12 FN3284.11 November 20, 2006