DS1651/DS3651 Quad High Speed MOS Sense Amplifiers General Description Features The DS1651/DS3651 is TTL compatible high speed circuits intended for sensing in a broad range of MOS memory system applications. Switching speeds have been enhanced over conventional sense amplifiers by application of Schottky technology, and TRI-STATE ® strobing is incorporated, offering a high impedance output state for bused organization. n n n n n n The DS1651/DS3651 has active pull-up outputs and offers open collector outputs providing implied “AND” operations. Connection Diagram High speed TTL compatible Input sensitivity — ± 7 mV TRI-STATE outputs for high speed buses Standard supply voltages — ± 5V Pin and function compatible with MC3430 Truth Table Dual-in-Line Package Input Strobe Output DS3651 VID ≥ 7 mW TA = 0˚C to +70˚C L H H Open −7 mV ≤ VID ≤ +7 mV TA = 0˚C to +70˚C L H X Open VID ≤ −7 mV TA = 0˚C to +70˚C L H L Open L = Low logic state H = High logic state Open = TRI-STATE X = Indeterminate state DS007528-1 Top View Order Number DS1651J, DS3651J or DS3651N See NS Package Number J16A or N16A TRI-STATE ® is a registered trademark of National Semiconductor Corporation. © 1999 National Semiconductor Corporation DS007528 www.national.com DS1651/DS3651 Quad High Speed MOS Sense Amplifiers June 1999 Typical Applications A Typical MOS Memory Sensing Application for a 4k work by 4-bit Memory Arrangement Employing 1103 Type Memory Devices DS007528-2 Note: Only 4 devices are required for a 4k word by 16-bit memory system. www.national.com 2 Absolute Maximum Ratings (Note 2) Operating Conditions If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage (VCC) DS1651 DS3651 Supply Voltage (VEE) DS1651 DS3651 Operating Temperature (TA) DS1651 DS3651 Output Load Current, (IOL) Differential Mode Input Voltage Range, (VIDR) Common-Mode Input Voltage Range, (VICR) Input Voltage Range (Any Input to GND), (VIR) Power Supply Voltages +7 VDC VCC VEE −7 VDC Differential-Mode Input Signal Voltage ± 6 VDC Range, VIDR Common-Mode Input Voltage Range, ± 5 VDC VICR Strobe Input Voltage, VI(S) 5.5 VDC Strobe Temperature Range −65˚C to +150˚C Maximum Power Dissipation (Note 1) at 25˚C Cavity Package 1509 mW Molded Package 1476 mW Lead Temp. (Soldering, 10 seconds) 300˚C Min Max Unit 4.5 4.75 5.5 5.25 V V −4.5 −4.75 −5.5 −5.25 V V −55 0 +125 +70 16 ˚C ˚C mA −5.0 +5.0 V −3.0 +3.0 V −5.0 +3.0 V Electrical Characteristics VCC = 5 VDC, VEE = −5 VDC, Min ≤ TA ≤ Max, unless otherwise noted (Notes 3, 4) Symbol VIS Parameter Input Sensitivity (Note 6) (Common-Mode Voltage Range) VICR = −3V ≤ VIN ≤ +3V Conditions Min Typ Min ≤ VCC ≤ Max Min ≥ VEE ≥ Max VIO Input Offset Voltage IIB Input Bias Current IIO Input Offset Current VIL(S) Strobe Input Voltage (Low State) VIH(S) Strobe Input Voltage (High State) IIL(S) Strobe Current (Low State) VCC = Max, VEE = Max, VIN = 0.4V IIL(S) Strobe Current (High State) VCC = Max, VEE = Max Max Unit ± 7.0 mV 2 VCC = Max, VEE = Max mV 20 0.5 µA 0.8 2 VIN = 2.4V −1.6 DS3651 DS1651 VIN = VCC VOH Output Voltage (High States) VCC = Min, VEE = Min IO = −400 µA VOL Output Voltage (Low State) VCC = Min, VEE = Min IO = 16 mA DS1651/DS3651 V V VIN = VCC VIN = 2.4V µA mA 40 µA 1 mA 100 µA 1 mA 2.4 V DS3651 0.45 DS1651 0.50 IOS Output Current Short Circuit VCC = Max, VEE = Max, (Note 5) DS1651/DS3651 IOFF Output Disable Leakage Current VCC = Max, VEE = Max DS3651 40 µA DS1651 100 µA ICC High Logic Level Supply Current VCC = Max, VEE = Max 45 60 mA IEE High Logic Level Supply Current VCC = Max, VEE = Max −17 −30 mA 3 −18 −70 V mA www.national.com Switching Characteristics VCC = 5 VDC, VEE = −5 VDC, TA = 25˚C unless otherwise noted. Typ Max Units tPHL(D) Symbol High-to-Low Logic Level Propagation Delay Time (Differential Inputs) Parameter 5 mV + VIS, (Figure 2) Conditions DS1651/ DS3651 Min 23 45 ns tPLH(D) Low-to-High Logic Level Propagation Delay Time (Differential Inputs) 5 mV + VIS, (Figure 2) DS1651/ DS3651 22 55 ns tPOH(S) TRI-STATE to High Logic Level Propagation Delay Time (Strobe) (Figure 1) DS1651/ DS3651 16 21 ns tPHO(S) High Logic Level to TRI-STATE Propagation Delay Time (Strobe) (Figure 1) DS1651/ DS3651 7 18 ns tPOL(S) TRI-STATE to Low Logic Level Propagation Delay Time (Strobe) (Figure 1) DS1651/ DS3651 19 27 ns tPLO(S) Low Logic Level to TRI-STATE Propagation Delay Time (Strobe) (Figure 1) DS1651/ DS3651 14 29 ns Note 1: Derate cavity package 10.1 mW/˚C above 25˚C; derate molded package 11.8 mW/˚C above 25˚C. Note 2: “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. Except for “Operating Temperature Range” they are not meant to imply that the device should be operated at these limits. The table of “Electrical Characteristics” provides conditions for actual device operation. Note 3: Unless otherwise specified min/max limits apply across the 0˚C to +70˚C range for the DS3651 and across the −55˚C to +125˚C range for the DS1651. All typical values are for TA = 25˚C, VCC = 5V and VEE = −5V. Note 4: All currents into device pins shown as positive, out of device pins as negative, all voltages referenced to ground unless otherwise noted. All values shown as max or min on absolute value basis. Note 5: Only one output at a time should be shorted. Note 6: A parameter which is of primary concern when designing with sense amplifiers is, what is the minimum differential input voltage required at the sense amplifier input terminals to guarantee a given output logic state. This parameter is commonly referred to as threshold voltage. It is well known that design considerations of threshold voltage are plagued by input offset currents, bias currents, network source resistances, and voltage gain. As a design convenience, the DS1651 and DS3651 are specified to a parameter called input sensitivity (VIS). This parameter takes into consideration input offset currents and bias currents, and guarantees a minimum input differential voltage to cause a given output logic state with respect to a maximum source impedance of 200Ω at each input. Switching Time Waveform DS007528-3 Note: Output of channel B shown under test, other channels are tested similarly. Delay V1 V2 S1 S2 CL tPLO(S)) 100 mV GND Closed Closed 15 pF 50 pF tPOL(S) 100 mV GND Closed Open tPHO(S) GND 100 mV Closed Closed 15 pF tPOH(S) GND 100 mV Open Closed 50 pF CL includes jig and probe capacitance. EIN waveform characteristics: tTLH and tTHL ≤ 10 ns measured 10% to 90% PRR = 1 MHz Duty cycle = 50% www.national.com 4 AC Test Circuits tPLO(S) tPHO(S) DS007528-5 DS007528-4 tPOH(S) tPOL(S) DS007528-7 DS007528-6 FIGURE 1. Strobe Propagation Delay tPLO(S), tPOL(S), tPHL(S) and tPOH(S) DS007528-8 Note: Output of channel B shown under test, other channels are tested similarly. S1 at “B” for DS1651/DS3651, CL = 50 pF total for DS1651/DS3651. DS007528-9 EIN waveform characteristics: tTLH and tTHL ≤ 10 ns measured 10% to 90% PRR = 1 MHz, duty cycle = 500 ns FIGURE 2. Differential Input Propagation Delay tPLH(D) and tPHL(D) 5 www.national.com Schematic Diagrams DS1651/DS3651 DS007528-10 www.national.com 6 Typical Applications Level Detector with Hysteresis Transfer Characteristics and Equations for Level Detector with Hysteresis DS007528-11 DS007528-12 7 www.national.com Typical Applications (Continued) 4-Bit Parallel A/D Converter DS007528-14 20 = (A + B) (C + D) (E + F) (H + J) (K + L) (M + N) (P + R) (S) 21 = (B + D) (F + J) (L + N) (R) 22 = (D + J) (N) 23 = J Conversion time ) 50 ns www.national.com 8 Physical Dimensions inches (millimeters) unless otherwise noted Ceramic Dual-in-Line Package (J) Order Number DS1651J, DS1653J, DS3651J or DS3653J NS Package Number J16A Molded Dual-in-Line Package (N) Order Number DS3651N or DS3653N NS Package Number N16A 9 www.national.com DS1651/DS3651 Quad High Speed MOS Sense Amplifiers Notes LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Americas Tel: 1-800-272-9959 Fax: 1-800-737-7018 Email: [email protected] www.national.com National Semiconductor Europe Fax: +49 (0) 1 80-530 85 86 Email: [email protected] Deutsch Tel: +49 (0) 1 80-530 85 85 English Tel: +49 (0) 1 80-532 78 32 Français Tel: +49 (0) 1 80-532 93 58 Italiano Tel: +49 (0) 1 80-534 16 80 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: [email protected] National Semiconductor Japan Ltd. Tel: 81-3-5639-7560 Fax: 81-3-5639-7507 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.