Built-in power supply photoelectric sensor E3JK Pre-wired type/E3JK ● Slim body full of functions and economically available Wide range voltage power supply Sensor type Shape Connection method Sensing distance Through-beam Output form 5m * Retroreflective model (with M.S.R. function) 2.5m (3m) Pre-wired models * Retroreflective model (without M.S.R. function) 4m (5m) Diffuse-reflective 300mm Output Light ON Relay output Dark ON Light ON/ Dark ON DC transistor output (selectable) Light ON Relay output Dark ON Light ON/Dark ON DC transistor NPN (selectable) output PNP Light ON Relay output Dark ON Light ON/Dark ON DC transistor output (selectable) (NPN) Light ON Relay output Dark ON Light ON/Dark ON DC transistor output (selectable) (NPN) Model E3JK-5M1 E3JK-5M2 NPN: E3JK-5S3 E3JK-R2M1 E3JK-R2M2 E3JK-R2S3 E3JK-R2R3 E3JK-R4M1 E3JK-R4M2 E3JK-R4S3 E3JK-DS30M1 E3JK-DS30M2 E3JK-DS30S3 * The value within the parentheses indicates the sensing distance applied when the E39-R2 reflector is used. Note: The UL-listed model ends with "-US". (Example: E3JK-5M1-US). Note that the DC transistor type of the E3JK is UL-unlisted. Accessories (Order Separately) Slits Slit width Sensing distance Width 1 mmx20 mm E3JK-5## A-218 0.7 m Minimum sensing object (typical) Model Quantity Remarks 1 mm dia. E39-S39 1 pc. each for emitter and receiver (total 2 pcs.) (Seal type long slit) Can be used with the throughbeam model E3JK-5##. Photoelectric Sensors Reflectors Reflectors Small reflector Tape Reflector Sensing distance (typical) E3JK-R2## 2.5 m (rated value) E3JK-R4## 4 m (rated value) E3JK-R2## 3m E3JK-R4## 5m E3JK-R2## 1 m (5 mm) * E3JK-R2## 750 mm (200 mm) * E3JK-R2## 1.2 m (200 mm) * E3JK-R2## 1.5 m (200 mm) * Model Quantity Remarks Attached to the E3JK-R2##. Attached to the E3JK-R4##. E39-R1 1 E39-R2 1 --- E39-R3 E39-RS1 E39-RS2 E39-RS3 1 --- 1 E3JK Name The M.S.R. function is available. * Values in parentheses indicate the minimum required distance between the sensor and reflector. Note: When the reflector used is other than the supplied one, set the sensing distance to about 0.7 times of the typical example as a guideline. Mounting Brackets Shape Model Quantity E39-L40 1 Remarks Supplied with E3JK Note: If a through-beam model is used, order two Mounting Brackets for the emitter and receiver respectively. E3JK A-219 Rating/Performance E3JK Sensor type Item Model Through-beam E3JK-5M# E3JK-5S3 Retroflective model (with M.S.R. function) E3JK-R2M# E3JK-R2#3 Sensing distance 5m 2.5 m (When using the E39-R1) Standard sensing object Opaque 14.8 dia. min. Opaque: 75 mm dia. min. Differential distance Retroflective model (without M.S.R. function) E3JK-R4M# E3JK-R4S3 E3JK-DS30M# E3JK-DS30S3 4m (When using the E39-R1) 20% max. of sensing distance --Both emitter and receiver: 3°C to 20°C 1° to 5° Light source (wave length) Infrared LED (950 nm) Red LED (660 nm) Power supply voltage 12 to 240 VDC ±10% ripple (p-p) : 10% max. 24 to 240 VAC ±10% 50/60 Hz DC 3 W max. 2 W max. AC 3 W max. 2 W max. Control output Life expectancy (relay output) Relay output: 250VAC 3 A (cosj=1) max., 5 VDC 10 mA min. --Infrared LED (950 nm) DC SSR Negative or positive Relay common output: 48 VDC 250VAC 100 mA max. 3 A (cosj=1) Leak current max., 5 VDC 0.1 mA max. 10 mA min. With load short-circuit protection DC SSR Negative common Relay 48 VDC output: 100 mA max. 250VAC Leak current 3 A (cosj=1) 0.1 mA max. max., 5 VDC With load 10 mA min. short-circuit protection Mechanical 50 million times or more (switching frequency 18,000 times/hour) Electrical 100 thousand times or more (switching frequency 18,000 times/hour) Response time 30 ms max. 10 ms max. 30 ms max. Sensitivity adjustment 300 mm (White paper 100x100 mm) --- Directional angle Current consumption Diffuse-reflective 5 ms max. 30 ms max. DC SSR Negative common Relay 48 VDC output: 100 mA max. 250VAC Leak current 3 A (cosj=1) 0.1 mA max. max., 5 VDC With load 10 mA min. short-circuit protection DC SSR Negative common 48 VDC 100 mA max. Leak current 0.1 mA max. With load short-circuit protection 5 ms max. 5 ms max. --- Ambient illuminance Incandescent lamp: 3,000 lux max. Ambient temperature Operating: -25°C to 55°C, Storage: -30°C to 70°C (with no icing or condensation) Ambient humidity Operating: 45% to 85%RH, Storage: 35% to 95%RH (with no condensation) Insulation resistance 20 M W min. at 500 VDC 30 ms max. Single-turn adjustment Dielectric strength 1,500 VAC at 50/60 Hz for 1 minute Vibration resistance A-220 Destruction 10 to 55 Hz, 1.5 mm double amplitude for 2 hours each in X, Y, and Z directions Malfunction 10 to 55 Hz, 1.5 mm double amplitude for 2 hours each in X, Y, and Z directions Photoelectric Sensors Item Shock resistance Model Through-beam E3JK-5M# E3JK-5S3 Retroflective model (with M.S.R. function) E3JK-R2M# Destruction: 500 m/s2 for 3 times each in X, Y, and Z directions Malfunction Destruction: 100m/s2 (approx. 10G) 3 times each in X, Y, and Z directions Destruction: 500 m/s2 for 3 times each in X, Y, and Z directions Destruction: 100m/s2 Destruction: (approx. 500 m/s2 for 10G) 3 times 3 times each each in X, Y, in X, Y and and Z direc Z directions tions IEC60529 IP64 Connection method Pre-wired models (standard length: 2 m) Weight (Packed state) Approx. 420 g Case ABS Lens Acrylics Mounting bracket Steel Accessories E3JK E3JK-R4M# Destruction Protective structure Material E3JK-R2#3 Retroflective model (without M.S.R. function) Destruction: 100m/s2 (approx. 10G) 3 times each in X, Y, and Z direc tions Diffuse-reflective E3JK-R4S3 E3JK-DS30M# E3JK-DS30S3 Destruction: 500 m/s2 for 3 times each in X, Y, and Z directions Destruction: 100m/s2 (approx. 10G) 3 times each in X, Y, and Z direc tions Destruction: 500 m/s2 for 3 times each in X, Y, and Z directions Approx. 250 g Mounting bracket (with screws), nuts, instruction manual, reflector (retroreflective model only) A-221 E3JK Sensor type Characteristic data (typical) 100 50 30 Reflector: E39-R1 50 30 10 100 Sensing object: White paper 50 30 10 5 5 3 3 Operating voltage 1 Operating 1 voltage 10 5 3 100 Diffuse-reflective E3JK-DS30## Excess gain ratio 1,000 500 300 Retroreflective Models E3JK-R2## + E39-R1 (supplied reflector) Excess gain ratio Excess gain ratio Excess Gain Ratio vs. Setting Distance Through-beam model E3JK-5## Operating 1 voltage 0 1 2 3 4 5 6 7 0 8 1 2 Setting distance (m) 3 4 Setting distance (m) 0 100 200 300 400 500 Setting distance (mm) Excess gain ratio E3JK-R4## + E39-R1 (supplied reflector) 100 Reflector: E39-R1 50 30 10 5 3 Operating 1 voltage 0 1 2 3 4 5 Setting distance (m) A-222 Photoelectric Sensors Output Circuit Diagram E3JK Relay output Timing chart E3JK-5M1 E3JK-5M2 Output circuit 24 to 240 VAC 12 to 240 VDC Brown Power Incident E3JK-R2M1 E3JK-R2M2 E3JK-R4M1 E3JK-R4M2 E3JK-DS30M1 E3JK-DS30M2 Light indicator (red) Interrupted ON OFF L-ON(Ta) (E3JK-##M1) ON OFF D-ON(Ta) (E3JK-##M2) ON OFF E3JK Model Main circuit source Blue (Polarity Optional) White Tc Black Tb Contact output Ta Gray Built-in relay: G6C DC transistor output Model Timing chart Output circuit Brown 24 to 240 VAC 12 to 240 VDC Power source Incident E3JK-5S3 E3JK-R2S3 E3JK-R4S3 E3JK-DS30S3 Interrupted Light ON indicator OFF (red) ON L-ON mode OFF ON D-ON mode OFF Blue White Drive circuit Black (L-ON) Load Main circuit Drive circuit Gray (D-ON) Load 24 to 240 VAC 12 to 240 VDC Brown Power source (Polarity Optional) Blue E3JK-R2R3 Incident Interrupted Light ON indicator OFF (red) ON L-ON mode OFF ON D-ON mode OFF D/ON Drive Load Gray I1 circuit L/ON Main circuit Drive circuit Load 48 VDC max. Black I2 I1 + I2 < 100 mA White Note: The output stage leakage currents are 0.1 mA max., respectively. Note: Connect to brown and blue on the emitter side. E3JK A-223 Operation Adjustment Item Model Through-beam Retroreflective Models Diffuse-reflective Without sensing object Setting Background object With sensing object Operation (A) (A) (C)Reset (A) (C) (B) Operation Swing the receiver and emitter vertically and/or horizontally and set the adjuster in the center of the range where the indicator of the receiver turns ON. E3JK Like the through-beam model, adMIN MAX MIN MAX MIN MAX just the reflector and emitter/reSensitivity Sensitivity Sensitivity ceiver. Since the directional angle of the emitter/receiver is 1 to 5°, ad- (1) If you have a sensing object as shown in the figure, turn the sensitivity adjuster clockwise (increase the sensitivity) until the indicator is turned just the emitter/receiver especially ON, and define this adjuster position as (A). carefully. (2) Remove the sensing object, turn the sensitivity adjuster clockwise until the indicator is turned ON by a background object, and define this position as (B). (3) Turn the sensitivity adjuster counterclockwise (decrease the sensitivity) from (B) until the indicator is turned OFF, and define this position as (C). (4) The position in the middle of (A) and (C) is the optimum position. If the indicator is not turned ON by the background object at the maximum sensitivity, set the adjuster in the middle of (A) and maximum sensitivity. ∑ The sensitivity adjuster may be damaged if an excessive force is applied. Precautions Correct Use E3JK Design Power Reset Time The Sensor is ready to detect an object within 200 ms after it is turned ON. If Sensor and load are connected to separate power supplies, ensure to turn ON the Sensor first. Wiring Considerations Connection/Wiring If the DC transistor output type is used, the sum of load currents of L-ON output (NO) and D-ON output (NC) should be within 100 mA. If the sum of load currents exceeds 100 mA, the load short-circuit protection may be activated. (The load short-circuit protection is reset by turning OFF the power of the photoelectric sensor.) Miscellaneous Ambient Conditions (Installation Area) The E3JK will malfunction if installed in the following places. • Places where the E3JK is exposed to a dusty environment. • Places where corrosive gases are produced. Emitter Receiver • Places where the E3JK is directly exposed to water, oil, or chemicals. Emitter Receiver A-224 Photoelectric Sensors Dimensions (Unit: mm) Sensors CAD file E3JK_01 E3JK-R2## E3JK-R4## E3JK-DS30## With Mounting Bracket Attached CAD file E3JK_02 E3JK E3JK-5## v 6-dia., 5-conductor, vinyl-insulated round cable (conductor cross-sectional area: 0.3 mm²; insulation diameter: 1.5 mm). Standard length: 2 m. * 3 With Mounting Bracket Attached 6-dia., 5-conductor, vinyl-insulated round cable (conductor cross-sectional area: 0.3 mm²; insulation diameter: 1.5 mm). Standard length: 2 m. * 3 Sensitivity adjustment volume * 2 40 22 21 12 6.4 Emitter: E3JK-5L Receiver: E3JK-5D## 40 12 6 dia. 4 9 21 12 12 6.4 6.4 7 18 ( A ) * 1 13.4 Light indicator Lens 50 40 21.5 10˚ 2-M6 42 58 Steel 5 Optical axis 40 40 60 R56.6 10˚ Mounting Holes 2-M6 Mounting Holes 7 50 40 25 60 R56.6 36.5 28 Receiver 50 Optical axis 6.4 18 5 Emitter 28 9 42 50 40 6 dia. 4 18 42 18 Indicator *2 13.4 (A)*1 Lens 14.8 dia. 22 Steel 58 * 1. Mounting brackets can be used on the A side (Two, M4 x 20 attached) . * 2. No sensitivity adjustment volume on the retororeflective model. 42 * 1.Mounting brackets can be used on the A side (Two, M4 x 20 attached) . * 2.Emitter: Power indicator Receiver: Light indicator * 3.Emitter includes 2-conductor. Accessories (Order Separately) Seal type long slit (for E3JK) E39-S39 14 1±0.1 20 26.5 Material: Polyester 0.1 mm thick E3JK A-225