TRIPLE INDEPENDENT LOGIC INTERFACED HALF BRIDGES EBO2 M I C R O T E C H N O L O G Y HTTP://WWW.APEXMICROTECH.COM (800) 546-APEX (800) 546-2739 FEATURES • • • • • COMPATIBLE WITH PWM FREQUENCIES UP TO 50KHZ 10V TO 100 V MOTOR SUPPLY 10A CONTINUOUS OUTPUT CURRENT HCMOS COMPATIBLE SCHMITT TRIGGER LOGIC INPUTS SEPARATE SOURCE OUTPUTS FOR NEGATIVE RAIL CURRENT SENSE • SLEEP MODE • WIDE RANGE FOR GATE DRIVE AND LOGIC SUPPLIES APPLICATIONS HIGH POWER CIRCUITS FOR DIGITAL CONTROL OF: • THREE AXIS MOTION USING BRUSH TYPE MOTORS • THREE PHASE BRUSHLESS DC MOTOR DRIVE • THREE PHASE AC MOTOR DRIVE • THREE PHASE STEP MOTOR DRIVE DESCRIPTION 13 HV1 14 OUT1 15 S1 16 HVRTN1 17 HV2 18 OUT2 Lin2 6 19 S2 5 20 HVRTN2 Hin 1 12 SD 11 Half Bridge Driver FET Half Bridge Output Lin 1 10 Vcc1 9 Hin 2 8 Vss,Logic Ground 7 The EB02 consists of three independent FET half bridges with drivers. The drivers may be interfaced with CMOS or HCMOS level logic. Vcc 2 Half Bridge Driver FET Half Bridge Output Vdd,Logic Supply 4 21 HV3 Hin3 3 Half Bridge Driver Lin 3 2 Vcc 3 1 FET Half Bridge Output 22 OUT3 23 S3 24 HVRTN3 FIGURE 1. BLOCK DIAGRAM APEX MICROTECHNOLOGY CORPORATION • TELEPHONE (520) 690-8600 • FAX (520) 888-3329 • ORDERS (520) 690-8601 • EMAIL [email protected] 1 ABSOLUTE MAXIMUM RATINGS SPECIFICATIONS EB02 ABSOLUTE MAXIMUM RATINGS SPECIFICATIONS MOTOR VOLTAGE SUPPLY, HV OUTPUT CURRENT, peak OUTPUT CURRENT, continuous1 GATE SUPPLY VOLTAGE, Vcc LOGIC SUPPLY VOLTAGE, Vdd POWER DISSIPATION, internal1 LOGIC INPUT VOLTAGE THERMAL RESISTANCE TO CASE3 TEMPERATURE, pin solder, 10s TEMPERATURE, junction2 TEMPERATURE RANGE, storage OPERATING TEMPERATURE, case PARAMETER TEST CONDITIONS POSITIVE OUTPUT VOLTAGE IOUT=10A; Vcc=10.8V, Vdd=5V; HV=100V, Fpwm=50kHz, L=100 µH " " " " " Set by external circuitry Set by internal resistors NEGATIVE OUTPUT VOLTAGE POSITIVE EDGE DELAY RISETIME NEGATIVE EDGE DELAY FALLTIME PWM FREQUENCY INPUT IMPEDANCE MIN 100V 20A 10A 20V 20V 51 Watts -0.3V to Vdd + 0.3V 2.1°C/Watt 300°C 150°C –55 to +150°C –25 to +85°C TYP 99.2 -1.5 MAX UNITS 101.5 Volts .8 Volts n-second n-second n-second n-second kHz k-ohm 260 50 310 5 0 50 50 INPUT AND OUTPUT SIGNALS PIN SYMBOL FUNCTION PIN SYMBOL FUNCTION 1 2 3 4 5 6 7 8 9 10 11 12 Vcc3 Lin3 Hin3 Vdd Vcc2 Lin2 Vss Hin2 Vcc1 Lin1 SD Hin1 Gate supply 3 Low drive logic in 3 High drive logic in 3 Logic supply Gate supply 2 Low drive logic in 2 Signal ground High drive logic in 2 Gate supply 1 Low drive logic in 1 Shut down logic in High drive logic in 1 13 14 15 16 17 18 19 20 21 22 23 24 HV1 OUT1 S1 HVRTN1 HV2 OUT 2 S2 HVRTN2 HV3 OUT 3 S3 HVRTN 3 High Voltage supply 1 Section 1 output Section 1 source Section 1 return High voltage supply 2 Section 2 output Section 2 source Section 2 return High voltage supply 3 Section 3 output Section 3 source Section 3 return NOTES: 1. 2. 3. Over full operating temperature range. Long term operation at the maximum junction temperature will result in reduced product life. Lower internal temperature by reducing internal dissipation or using better heatsinking to achieve high MTTF. Each FET. INPUT A logic level input independently controls each FET in the half bridge. A logic level high turns on the FET and low turns it off. A common shut down input turns off all FETs when high. All inputs are Schmitt triggers with the upper threshold at 2/3 Vdd and the lower threshold at 1/3 Vdd. This comfortably interfaces with CMOS or HCMOS provided that the Vdd for the logic family and the EB02 are the same. TTL families may be used if a pull-up to Vcc is added to the TTL gates driving the EB02, and Vdd for the EB02 is the same supply as Vcc for the TTL family. An open signal connector pulls the shut down input high and all other inputs low, insuring that all outputs are off. However, input impedance is 50k on all inputs; therefore, if one input is open circuited a high radiated noise level could spuriously turn on a FET. OUTPUT Each output section consists of a switching mode FET half bridge. Separate HV supply, emitter, and HV return lines are provided for each section. The FETs are conservatively rated to carry 10A. At 10A the saturation voltage is 1.5 V maximum, over the full environmental range. Each FET has an intrinsic diode connected in anti-parallel. When switching an inductive load this diode will conduct, and the drop at 10A will be 1.5V maximum, over the full environmental range. APEX MICROTECHNOLOGY CORPORATION • 5980 NORTH SHANNON ROAD • TUCSON, ARIZONA 85741 • USA • APPLICATIONS HOTLINE: 1 (800) 546-2739 2 PACKAGE SPECIFICATIONS EB02 PACKAGE SPECIFICATIONS DIP9 PACKAGE WEIGHT: 69 g or 2.4 oz DIMENSIONS ARE IN INCHES ALTERNATE UNITS ARE [MM] APEX MICROTECHNOLOGY CORPORATION • TELEPHONE (520) 690-8600 • FAX (520) 888-3329 • ORDERS (520) 690-8601 • EMAIL [email protected] 3 OPERATING CONSIDERATIONS EB02 POWER SUPPLY REQUIREMENTS SUPPLY HV1 HV2 HV3 Vcc1 Vcc2 Vcc3 Vdd VOLTAGE 10V to 100V 10V to 100V 10V to 100V 10V to 20V 10V to 20V 10V to 20V 4.5 to 20V MAX CURRENT 10A, continuous, 20A peak 10A, continuous, 20A peak 10A, continuous, 20A peak 10mA 10mA 10mA 10mA HV1, HV2, and HV3 may be used independently, or may be one supply. Also Vcc1, Vcc2, and Vcc3 may be used independently or tied together. The Vdd supply must be compatible with the input logic. If a high voltage logic such as CMOS is used it may be tied with the Vcc supplies. HCMOS requires a 5V±10% supply SPECIAL CONSIDERATIONS GENERAL The EB02 is designed to give the user maximum flexibility in a digital or DSP based motion control system. Thermal, overvoltage, overcurrent, and crossfire protection circuits are part of the user’s design. Users should read Application Note 1, "General Operating Considerations;” and Application Note 30, “PWM Basics” for much useful information in applying this part. These Application Notes are in the “Power Integrated Circuits Data Book” and on line at www.apexmicrotech.com. GROUNDING AND BYPASSING As in any high power PWM system, grounding and bypassing are some of the keys to success. The EB02 is capable of generating 2 kW pulses with 40 n-second rise and fall times. If improperly grounded or bypassed this can cause horrible conducted and radiated EMI. In order to reduce conducted EMI, the EB02 provides a separate power ground, named HVRTN, for each high voltage supply. These grounds are electrically isolated from the logic ground and each other. This isolation eliminates high current ground loops. However, more than 5V offset between the grounds will destroy the EB02. Apex recommends back to back high current diodes between logic and power grounds; this will maintain isolation but keep offset at a safe level. All grounds should tie together at one common point in the system. In order to reduce radiated EMI, Apex recommends a 100 µF or larger capacitor between HV and HVRTN. This capacitor should be a switching power grade capacitor with ESR rated at 20kHz. This capacitor should be placed physically as close to the EB02 as possible. However, such a capacitor will typically have a few hundred milli-ohms or so ESR. Therefore, each section must also be bypassed with a low ESR 1µF or larger ceramic capacitor. In order to minimize radiated noise, it is necessary to minimize the area of the loop containing high frequency current. (The size of the antenna.) Therefore, the 1µF ceramic capacitors should bypass each HV to its return at the pins of the EB02. SHOOT THROUGH PROTECTION Power FETs have a relatively short turn on delay, and a long turn off delay. Therefore, if the turn on input to an FET in a half bridge circuit is applied simultaneously with the turn off input to the other FET in that half bridge, there will be a time when both FETs are simultaneously on. This "shoot through condition" will short the power rails through the FETs, causing excessive power dissipation and very high EMI. To avoid the shoot through condition the turn on of one FET must be delayed long enough for the other FET in the same half bridge to have completely turned off. A delay of at least 0.5 µ-seconds is required for the EB02. This delay is required for both the Hin and Lin inputs. PROTECTION CIRCUITS The EB02 does not include protection circuits. However, there is a shut down input which will turn off all FETs when at logic “1”. This input may be used with user designed temperature sensing and current sensing circuits to shut down the FETs in the event of a detected unsafe condition. This is recommended since the FETs may be turned off this way even if the normal input logic or DSP programming is faulty. START UP CONSIDERATIONS The lower rail FET in the half bridge must be turned on for at least 2 µ-seconds to charge the bootstrap capacitor before the top rail FET can be turned on. This must be done no more than 330 µ-seconds prior to turning on the top rail FET. However, a grounded load will give the same purpose as turning on the lower rail FET. However a grounded load will give the same purpose as turning on the lower rail FET. Therefore a grounded load may be operated without this consideration. An internal floating supply is used to enhance the operation of the bootstrap bias circuit. This allows the top rail FETs to be held on indefinitely once turned on. HEATSINK The EB02 should be provided with sufficient heatsink to dissipate 51 watts when operating at 100V, 10A, 50kHz and 3 sections simultaneously providing maximum current. The dissipation is composed of conduction losses (I out xV sat ) up to 16 watt per half bridge and switching losses of about 1 watt per half bridge. The conduction losses are proportional to Iout; switching losses are proportional to HV supply voltage, load capacitance, and switching frequency. This data sheet has been carefully checked and is believed to be reliable, however, no responsibility is assumed for possible inaccuracies or omissions. All specificiations are subject to change without notice. APEX MICROTECHNOLOGY CORPORATION • 5980 NORTH SHANNON ROAD • TUCSON, ARIZONA 85741 • USA • APPLICATIONS HOTLINE: 1 (800) 546-2739 EBO2U REV. B JANUARY 2001 © 2001 Apex Microtechnology Corporation 4