Eon EN29LV160AB-70BCP 16 megabit (2048k x 8- bit / 1024 k x 16-bit) flash memory Datasheet

EN29LV160A
EN29LV160A
16 Megabit (2048K x 8-bit / 1024K x 16-bit) Flash Memory
Boot Sector Flash Memory, CMOS 3.0 Volt-only
FEATURES
• 3.0V, single power supply operation
- Minimizes system level power requirements
- Sector erase time: 500ms typical
- Chip erase time: 17.5s typical
• JEDEC Standard program and erase
commands
• High performance
- Access times as fast as 70 ns
• Low power consumption (typical values at 5
MHz)
- 9 mA typical active read current
- 20 mA typical program/erase current
- Less than 1 µA standby current
• JEDEC standard DATA# polling and toggle
bits feature
• Single Sector and Chip Erase
• Sector Unprotect Mode
• Embedded Erase and Program Algorithms
• Flexible Sector Architecture:
- One 16-Kbyte, two 8-Kbyte, one 32-Kbyte,
and thirty-one 64-Kbyte sectors (byte mode)
- One 8-Kword, two 4-Kword, one 16-Kword
and thirty-one 32-Kword sectors (word mode)
• Sector protection :
- Hardware locking of sectors to prevent
program or erase operations within individual
sectors
- Additionally, temporary Sector Group
Unprotect allows code changes in previously
locked sectors.
• High performance program/erase speed
- Byte/Word program time: 8µs typical
• Erase Suspend / Resume modes:
Read and program another Sector during
Erase Suspend Mode
• Triple-metal double-poly triple-well CMOS
Flash Technology
• Low Vcc write inhibit < 2.5V
• minimum 1,000K program/erase endurance
cycle
• Package Options
- 48-pin TSOP (Type 1)
- 48 ball 6mm x 8mm FBGA
• Commercial and Industrial Temperature
Range
GENERAL DESCRIPTION
The EN29LV160A is a 16-Megabit, electrically erasable, read/write non-volatile flash memory,
organized as 2,097,152 bytes or 1,048,576 words. Any byte can be programmed typically in 8µs.
The EN29LV160A features 3.0V voltage read and write operation, with access times as fast as
70ns to eliminate the need for WAIT states in high-performance microprocessor systems.
The EN29LV160A has separate Output Enable (OE#), Chip Enable (CE#), and Write Enable
(WE#) controls, which eliminate bus contention issues. This device is designed to allow either
single Sector or full chip erase operation, where each Sector can be individually protected
against program/erase operations or temporarily unprotected to erase or program. The device
can sustain a minimum of 1,000K program/erase cycles on each Sector.
This Data Sheet may be revised by subsequent versions
1
or modifications due to changes in technical specifications.
©2004 Eon Silicon Solution, Inc., www.essi.com.tw
Rev. C, Issue Date: 2005/01/07
EN29LV160A
CONNECTION DIAGRAMS
A15
A14
A13
A12
A11
A10
A9
A8
A19
NC
WE#
RESET#
NC
NC
RY/BY#
A18
A17
A7
A6
A5
A4
A3
A2
A1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
Standard
TSOP
FBGA
Top View, Balls Facing Down
A6
A13
A5
A9
B6
A12
B5
A8
A4
B4
WE#
RESET#
A3
B3
RY/BY#
NC
A2
B2
A7
A17
A1
B1
A3
A4
C6
A14
C5
A10
D6
E6
A15
F6
A16
D5
E5
A11
BYTE#
F5
DQ7
DQ14
G6
DQ15/A-1
G5
DQ13
H6
Vss
H5
DQ6
C4
D4
E4
F4
G4
H4
NC
A19
DQ5
DQ12
Vcc
DQ4
C3
D3
E3
F3
G3
H3
DQ2
DQ10
DQ11
DQ3
D2
E2
F2
G2
H2
A5
DQ0
DQ8
DQ9
DQ1
D1
E1
F1
G1
H1
A18
C2
A6
C1
A2
NC
A0
A1
This Data Sheet may be revised by subsequent versions
or modifications due to changes in technical specifications.
2
CE#
OE#
Vss
©2004 Eon Silicon Solution, Inc., www.essi.com.tw
Rev. C, Issue Date: 2005/01/07
A16
BYTE#
Vss
DQ15/A-1
DQ7
DQ14
DQ6
DQ13
DQ5
DQ12
DQ4
Vcc
DQ11
DQ3
DQ10
DQ2
DQ9
DQ1
DQ8
DQ0
OE#
Vss
CE#
A0
EN29LV160A
FIGURE 1. LOGIC DIAGRAM
TABLE 1. PIN DESCRIPTION
Pin Name
Function
EN29LV160A
A0-A19
20 Addresses
DQ0-DQ14
15 Data Inputs/Outputs
DQ15 / A-1
DQ15 (data input/output, word mode),
A-1 (LSB address input, byte mode)
CE#
Chip Enable
OE#
Output Enable
RESET#
Hardware Reset Pin
RY/BY#
Ready/Busy Output
WE#
Write Enable
Vcc
Supply Voltage
(2.7-3.6V)
Vss
Ground
NC
Not Connected to anything
BYTE#
Byte/Word Mode
DQ0 – DQ15
(A-1)
A0 – A19
Reset#
CE#
OE#
WE#
RY/BY#
Byte#
This Data Sheet may be revised by subsequent versions
or modifications due to changes in technical specifications.
3
©2004 Eon Silicon Solution, Inc., www.essi.com.tw
Rev. C, Issue Date: 2005/01/07
EN29LV160A
Table 2. Top Boot Sector Address Tables (EN29LV160AT)
Sector Size
(Kbytes/
Kwords)
Address Range (in hexadecimal)
62/32
Byte mode (x8)
000000–00FFFF
Word Mode
(x16)
00000–07FFF
X
64/32
010000–01FFFF
08000–0FFFF
X
64/32
020000–02FFFF
10000–17FFF
Sector
A19
A18
A17
A16
A15
A14
A13
A12
SA0
0
0
0
0
0
X
X
X
SA1
0
0
0
0
1
X
X
SA2
0
0
0
1
0
X
X
SA3
0
0
0
1
1
X
X
X
64/32
030000–03FFFF
18000–1FFFF
SA4
0
0
1
0
0
X
X
X
64/32
040000–04FFFF
20000–27FFF
SA5
0
0
1
0
1
X
X
X
64/32
050000–05FFFF
28000–2FFFF
SA6
0
0
1
1
0
X
X
X
64/32
060000–06FFFF
30000–37FFF
SA7
0
0
1
1
1
X
X
X
64/32
070000–07FFFF
38000–3FFFF
SA8
0
1
0
0
0
X
X
X
64/32
080000–08FFFF
40000–47FFF
SA9
0
1
0
0
1
X
X
X
64/32
090000–09FFFF
48000–4FFFF
SA10
0
1
0
1
0
X
X
X
64/32
0A0000–0AFFFF
50000–57FFF
SA11
0
1
0
1
1
X
X
X
64/32
0B0000–0BFFFF
58000–5FFFF
SA12
0
1
1
0
0
X
X
X
64/32
0C0000–0CFFFF
60000–67FFF
SA13
0
1
1
0
1
X
X
X
64/32
0D0000–0DFFFF
68000–6FFFF
SA14
0
1
1
1
0
X
X
X
64/32
0E0000–0EFFFF
70000–77FFF
SA15
0
1
1
1
1
X
X
X
64/32
0F0000–0FFFFF
78000–7FFFF
SA16
1
0
0
0
0
X
X
X
64/32
100000–10FFFF
80000–87FFF
SA17
1
0
0
0
1
X
X
X
64/32
110000–11FFFF
88000–8FFFF
SA18
1
0
0
1
0
X
X
X
64/32
120000–12FFFF
90000–97FFF
SA19
1
0
0
1
1
X
X
X
64/32
130000–13FFFF
98000–9FFFF
SA20
1
0
1
0
0
X
X
X
64/32
140000–14FFFF
A0000–A7FFF
SA21
1
0
1
0
1
X
X
X
64/32
150000–15FFFF
A8000–AFFFF
SA22
1
0
1
1
0
X
X
X
64/32
160000–16FFFF
B0000–B7FFF
SA23
1
0
1
1
1
X
X
X
64/32
170000–17FFFF
B8000–BFFFF
SA24
1
1
0
0
0
X
X
X
64/32
180000–18FFFF
C0000–C7FFF
SA25
1
1
0
0
1
X
X
X
64/32
190000–19FFFF
C8000–CFFFF
SA26
1
1
0
1
0
X
X
X
64/32
1A0000–1AFFFF
D0000–D7FFF
SA27
1
1
0
1
1
X
X
X
64/32
1B0000–1BFFFF
D8000–DFFFF
SA28
1
1
1
0
0
X
X
X
64/32
1C0000–1CFFFF
E0000–E7FFF
SA29
1
1
1
0
1
X
X
X
64/32
1D0000–1DFFFF
E8000–EFFFF
SA30
1
1
1
1
0
X
X
X
64/32
1E0000–1EFFFF
F0000–F7FFF
SA31
1
1
1
1
1
0
X
X
32/16
1F0000–1F7FFF
F8000–FBFFF
SA32
1
1
1
1
1
1
0
0
8/4
1F8000–1F9FFF
FC000–FCFFF
SA33
1
1
1
1
1
1
0
1
8/4
1FA000–1FBFFF
FD000–FDFFF
SA34
1
1
1
1
1
1
1
X
16/8
1FC000–1FFFFF
FE000–FFFFF
This Data Sheet may be revised by subsequent versions
or modifications due to changes in technical specifications.
4
©2004 Eon Silicon Solution, Inc., www.essi.com.tw
Rev. C, Issue Date: 2005/01/07
EN29LV160A
Table 3. Bottom Boot Sector Address Tables (EN29LV160AB)
Sector Size
(Kbytes/
Kwords)
Address Range (in hexadecimal)
Byte mode (x8)
Word Mode
(x16)
16/8
000000–003FFF
00000–01FFF
0
8/4
004000–005FFF
02000–02FFF
1
1
8/4
006000–007FFF
03000–03FFF
1
X
X
32/16
008000–00FFFF
04000–07FFF
1
X
X
X
64/32
010000–01FFFF
08000–0FFFF
1
0
X
X
X
64/32
020000–02FFFF
10000–17FFF
0
1
1
X
X
X
64/32
030000–03FFFF
18000–1FFFF
0
1
0
0
X
X
X
64/32
040000–04FFFF
20000–27FFF
0
0
1
0
1
X
X
X
64/32
050000–05FFFF
28000–2FFFF
SA9
0
0
1
1
0
X
X
X
64/32
060000–06FFFF
30000–37FFF
SA10
0
0
1
1
1
X
X
X
64/32
070000–07FFFF
38000–3FFFF
X
64/32
080000–08FFFF
40000–47FFF
X
64/32
090000–09FFFF
48000–4FFFF
X
64/32
0A0000–0AFFFF
50000–57FFF
X
64/32
0B0000–0BFFFF
58000–5FFFF
X
64/32
0C0000–0CFFFF
60000–67FFF
X
64/32
0D0000–0DFFFF
68000–6FFFF
X
64/32
0E0000–0EFFFF
70000–77FFF
X
64/32
0F0000–0FFFFF
78000–7FFFF
X
64/32
100000–10FFFF
80000–87FFF
110000–11FFFF
88000–8FFFF
Sector
A19
A18
A17
A16
A15
A14
A13
A12
SA0
0
0
0
0
0
0
0
X
SA1
0
0
0
0
0
0
1
SA2
0
0
0
0
0
0
SA3
0
0
0
0
0
SA4
0
0
0
0
SA5
0
0
0
SA6
0
0
SA7
0
SA8
SA11
SA12
SA13
SA14
SA15
SA16
SA17
SA18
SA19
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
0
0
0
0
0
1
1
1
1
0
0
0
1
1
0
0
1
1
0
0
1
0
1
0
1
0
1
0
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
SA20
1
0
0
0
1
X
X
X
64/32
SA21
1
0
0
1
0
X
X
X
64/32
120000–12FFFF
90000–97FFF
SA22
1
0
0
1
1
X
X
X
64/32
130000–13FFFF
98000–9FFFF
SA23
1
0
1
0
0
X
X
X
64/32
140000–14FFFF
A0000–A7FFF
SA24
1
0
1
0
1
X
X
X
64/32
150000–15FFFF
A8000–AFFFF
SA25
1
0
1
1
0
X
X
X
64/32
160000–16FFFF
B0000–B7FFF
SA26
1
0
1
1
1
X
X
X
64/32
170000–17FFFF
B8000–BFFFF
X
64/32
180000–18FFFF
C0000–C7FFF
X
64/32
190000–19FFFF
C8000–CFFFF
X
64/32
1A0000–1AFFFF
D0000–D7FFF
X
64/32
1B0000–1BFFFF
D8000–DFFFF
X
64/32
1C0000–1CFFFF
E0000–E7FFF
X
64/32
1D0000–1DFFFF
E8000–EFFFF
X
64/32
1E0000–1EFFFF
F0000–F7FFF
X
64/32
1F0000–1FFFFF
F8000–FFFFF
SA27
SA28
SA29
SA30
SA31
SA32
SA33
SA34
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
X
X
X
X
X
X
X
X
This Data Sheet may be revised by subsequent versions
or modifications due to changes in technical specifications.
X
X
X
X
X
X
X
X
5
©2004 Eon Silicon Solution, Inc., www.essi.com.tw
Rev. C, Issue Date: 2005/01/07
EN29LV160A
PRODUCT SELECTOR GUIDE
Product Number
Speed Option
EN29LV160A
Full Voltage Range: Vcc=2.7 – 3.6 V
-70
-90
Max Access Time, ns (tacc)
70
90
Max CE# Access, ns (tce)
70
90
Max OE# Access, ns (toe)
30
35
BLOCK DIAGRAM
RY/BY#
Vcc
Vss
DQ0-DQ15 (A-1)
Block Protect Switches
Erase Voltage Generator
Input/Output Buffers
State
Control
WE#
Command
Register
Program Voltage
Generator
Chip Enable
Output Enable
Logic
CE#
OE#
Vcc Detector
Timer
Address Latch
STB
STB
Y-Decoder
Y-Gating
X-Decoder
Cell Matrix
A0-A19
This Data Sheet may be revised by subsequent versions
or modifications due to changes in technical specifications.
6
©2004 Eon Silicon Solution, Inc., www.essi.com.tw
Rev. C, Issue Date: 2005/01/07
Data Latch
EN29LV160A
TABLE 3. OPERATING MODES
16M FLASH USER MODE TABLE
Operation
Read
Write
CMOS Standby
TTL Standby
Output Disable
Hardware Reset
Temporary
Sector Unprotect
CE#
L
L
Vcc ± 0.3V
H
L
X
OE#
L
H
X
X
H
X
WE#
H
L
X
X
H
X
Reset#
H
H
Vcc ± 0.3V
H
H
L
A0A19
AIN
AIN
X
X
X
X
X
X
X
VID
AIN
DQ0-DQ7
DOUT
DIN
High-Z
High-Z
High-Z
High-Z
DQ8-DQ15
Byte#
Byte#
= VIH
= VIL
DOUT
High-Z
DIN
High-Z
High-Z High-Z
High-Z High-Z
High-Z High-Z
High-Z High-Z
DIN
DIN
X
Notes:
L=logic low= VIL, H=Logic High= VIH, VID =11 ± 0.5V, X=Don’t Care (either L or H, but not floating!),
DIN=Data In, DOUT=Data Out, AIN=Address In
TABLE 4. Autoselect Codes (Using High Voltage, VID)
16M FLASH MANUFACTURER/DEVICE ID TABLE
Description
CE#
OE#
WE#
L
H
A19
to
A12
A11
to
A10
A92
X
VID
A8
A7
A6
A5
to
A2
A1
A0
X
L
X
L
L
DQ8
to
DQ15
L
Manufacturer ID:
Eon
L
Device
ID
Word
L
(top boot
block)
Byte
L
L
H
Device
ID
Word
L
L
H
(bottom
boot
block)
Byte
L
X
X
L
X
VID
X
VID
X
X
to
7FH
X
1CH
H
X
L
H1
DQ7
DQ0
X
X
L
L
X
X
L
L
22h
C4H
X
C4H
22h
49H
X
49H
X
(Protected
)
X
(Unprotect
ed)
H
H
H
01h
Sector Protection
Verification
L
L
H
SA
X
VID
X
X
L
X
H
L
00h
Note:
1. A8=H is recommended for Manufacturing ID check. If a manufacturing ID is read with A8=L, the chip will output a
configuration code 7Fh
2. A9 = VID is for HV A9 Autoselect mode only. A9 must be ≤ Vcc (CMOS logic level) for Command Autoselect Mode.
This Data Sheet may be revised by subsequent versions
or modifications due to changes in technical specifications.
7
©2004 Eon Silicon Solution, Inc., www.essi.com.tw
Rev. C, Issue Date: 2005/01/07
EN29LV160A
USER MODE DEFINITIONS
Word / Byte Configuration
The signal set on the BYTE# Pin controls whether the device data I/O pins DQ15-DQ0 operate in
the byte or word configuration. When the Byte# Pin is set at logic ‘1’, then the device is in word
configuration, DQ15-DQ0 are active and are controlled by CE# and OE#.
On the other hand, if the Byte# Pin is set at logic ‘0’, then the device is in byte configuration, and
only data I/O pins DQ0-DQ7 are active and controlled by CE# and OE#. The data I/O pins DQ8DQ14 are tri-stated, and the DQ15 pin is used as an input for the LSB (A-1) address function.
Standby Mode
The EN29LV160A has a CMOS-compatible standby mode, which reduces the current to < 1µA
(typical). It is placed in CMOS-compatible standby when the CE# pin is at VCC ± 0.5. RESET# and
BYTE# pin must also be at CMOS input levels. The device also has a TTL-compatible standby mode,
which reduces the maximum VCC current to < 1mA. It is placed in TTL-compatible standby when the
CE# pin is at VIH. When in standby modes, the outputs are in a high-impedance state independent
of the OE# input.
Read Mode
The device is automatically set to reading array data after device power-up. No commands are
required to retrieve data. The device is also ready to read array data after completing an Embedded
Program or Embedded Erase algorithm.
After the device accepts an Erase Suspend command, the device enters the Erase Suspend mode.
The system can read array data using the standard read timings, except that if it reads at an address
within erase-suspended sectors, the device outputs status data. After completing a programming
operation in the Erase Suspend mode, the system may once again read array data with the same
exception. See “Erase Suspend/Erase Resume Commands” for more additional information.
The system must issue the reset command to re-enable the device for reading array data if DQ5
goes high, or while in the autoselect mode. See the “Reset Command” additional details.
Output Disable Mode
When the CE# or OE# pin is at a logic high level (VIH), the output from the EN29LV160A is
disabled. The output pins are placed in a high impedance state.
Auto Select Identification Mode
The autoselect mode provides manufacturer and device identification, and sector protection
verification, through identifier codes output on DQ15–DQ0. This mode is primarily intended for
programming equipment to automatically match a device to be programmed with its corresponding
programming algorithm. However, the autoselect codes can also be accessed in-system through the
command register.
When using programming equipment, the autoselect mode requires VID (10.5 V to 11.5 V) on
address pin A9. Address pins A6, A1, and A0 must be as shown in Autoselect Codes table. In
addition, when verifying sector protection, the sector address must appear on the appropriate
highest order address bits. Refer to the corresponding Sector Address Tables. The Command
Definitions table shows the remaining address bits that are don’t-care. When all necessary bits have
been set as required, the programming equipment may then read the corresponding identifier code
on DQ15–DQ0.
This Data Sheet may be revised by subsequent versions
or modifications due to changes in technical specifications.
8
©2004 Eon Silicon Solution, Inc., www.essi.com.tw
Rev. C, Issue Date: 2005/01/07
EN29LV160A
To access the autoselect codes in-system; the host system can issue the autoselect command via
the command register, as shown in the Command Definitions table. This method does not require
VID. See “Command Definitions” for details on using the autoselect mode.
Write Mode
Programming is a four-bus-cycle operation. The program command sequence is initiated by writing
two unlock write cycles, followed by the program set-up command. The program address and data
are written next, which in turn initiate the Embedded Program algorithm. The system is not required
to provide further controls or timings. The device automatically provides internally generated
program pulses and verifies the programmed cell margin. The Command Definitions in Table 5 show
the address and data requirements for the byte program command sequence.
When the Embedded Program algorithm is complete, the device then returns to reading array data
and addresses are no longer latched. The system can determine the status of the program operation
by using DQ7 or DQ6. See “Write Operation Status” for information on these status bits.
Any commands written to the device during the Embedded Program Algorithm are ignored.
Programming is allowed in any sequence and across sector boundaries. A bit cannot be
programmed from a “0” back to a “1”. Attempting to do so may halt the operation and set DQ5 to
“1”, or cause the Data# Polling algorithm to indicate the operation was successful. However, a
succeeding read will show that the data is still “0”. Only erase operations can convert a “0” to a “1”.
Sector Protection/Unprotection
The hardware sector protection feature disables both program and erase operations in any sector.
The hardware sector unprotection feature re-enables both program and erase operations in
previously protected sectors.
There are two methods to enabling this hardware protection circuitry. The first one requires only
that the RESET# pin be at VID and then standard microprocessor timings can be used to enable or
disable this feature. See Flowchart 7a and 7b for the algorithm and Figure 12 for the timings.
When doing Sector Unprotect, all the other sectors should be protected first.
The second method is meant for programming equipment. This method requires VID be applied to
both OE# and A9 pin and non-standard microprocessor timings are used. This method is described
in a separate document called EN29LV160A Supplement, which can be obtained by contacting a
representative of Eon Silicon Solution, Inc.
Temporary Sector Unprotect
Start
This feature allows temporary unprotection of previously protected
sector groups to change data while in-system. The Sector
Unprotect mode is activated by setting the RESET# pin to VID.
During this mode, formerly protected sectors can be programmed
or erased by simply selecting the sector addresses. Once is
removed from the RESET# pin, all the previously protected sectors
are protected again.
See accompanying figure and timing
diagrams for more details.
Notes:
1. All protected sectors unprotected.
2. Previously protected sectors protected
again.
This Data Sheet may be revised by subsequent versions
or modifications due to changes in technical specifications.
9
Reset#=VID (note 1)
Perform Erase or Program
Operations
Reset#=VIH
Temporary Sector
Unprotect Completed (note 2)
©2004 Eon Silicon Solution, Inc., www.essi.com.tw
Rev. C, Issue Date: 2005/01/07
EN29LV160A
COMMON FLASH INTERFACE (CFI)
The common flash interface (CFI) specification outlines device and host systems software
interrogation handshake, which allows specific vendor-specified software algorithms to be used for
entire families of devices. Software support can then be device-independent, JEDEC IDindependent, and forward- and backward-compatible for the specified flash device families. Flash
vendors can standardize their existing interfaces for long-term compatibility.
This device enters the CFI Query mode when the system writes the CFI Query command, 98h, to
address 55h in word mode (or address AAh in byte mode), any time the device is ready to read
array data.
The system can read CFI information at the addresses given in Tables 5-8. In word mode, the
upper address bits (A7–MSB) must be all zeros. To terminate reading CFI data, the system must
write the reset command.
The system can also write the CFI query command when the device is in the autoselect mode. The
device enters the CFI query mode and the system can read CFI data at the addresses given in
Tables 5–8. The system must write the reset command to return the device to the autoselect mode.
Table 5. CFI Query Identification String
Adresses
(Word Mode)
10h
11h
12h
13h
14h
15h
16h
17h
18h
19h
1Ah
Adresses
(Byte Mode)
20h
22h
24h
26h
28h
2Ah
2Ch
2Eh
30h
32h
34h
Addresses
(Word Mode)
1Bh
Addresses
(Byte Mode)
36h
Data
0027h
1Ch
38h
0036h
1Dh
1Eh
1Fh
20h
3Ah
3Ch
3Eh
40h
0000h
0000h
0004h
0000h
21h
22h
23h
24h
25h
26h
42h
44h
46h
48h
4Ah
4Ch
000Ah
0000h
0005h
0000h
0004h
0000h
Data
0051h
0052h
0059h
0002h
0000h
0040h
0000h
0000h
0000h
0000h
0000h
Description
Query Unique ASCII string “QRY”
Primary OEM Command Set
Address for Primary Extended Table
Alternate OEM Command set (00h = none exists)
Address for Alternate OEM Extended Table (00h = none exists
Table 6. System Interface String
Description
Vcc Min (write/erase)
D7-D4: volt, D3 –D0: 100 millivolt
Vcc Max (write/erase)
D7-D4: volt, D3 –D0: 100 millivolt
Vpp Min. voltage (00h = no Vpp pin present)
Vpp Max. voltage (00h = no Vpp pin present)
Typical timeout per single byte/word write 2^N µs
Typical timeout for Min, size buffer write 2^N µs (00h = not
supported)
Typical timeout per individual block erase 2^N ms
Typical timeout for full chip erase 2^N ms (00h = not supported)
Max. timeout for byte/word write 2^N times typical
Max. timeout for buffer write 2^N times typical
Max. timeout per individual block erase 2^N times typical
Max timeout for full chip erase 2^N times typical (00h = not
supported)
This Data Sheet may be revised by subsequent versions
or modifications due to changes in technical specifications.
10
©2004 Eon Silicon Solution, Inc., www.essi.com.tw
Rev. C, Issue Date: 2005/01/07
EN29LV160A
Table 7. Device Geometry Definition
Addresses
(Word mode)
27h
28h
29h
2Ah
2Bh
2Ch
2Dh
2Eh
2Fh
30h
31h
32h
33h
34h
35h
36h
37h
38h
39h
3Ah
3Bh
3Ch
Addresses
(Byte Mode)
4Eh
50h
52h
54h
56h
58h
5Ah
5Ch
5Eh
60h
62h
64h
66h
68h
6Ah
6Ch
6Eh
70h
72h
74h
76h
78h
Data
0015h
0002h
0000h
0000h
0000h
0004h
0000h
0000h
0040h
0000h
0001h
0000h
0020h
0000h
0000h
0000h
0080h
0000h
001Eh
0000h
0000h
0001h
Description
Device Size = 2^N byte
Flash Device Interface description (refer to CFI publication 100)
Max. number of byte in multi-byte write = 2^N
(00h = not supported)
Number of Erase Block Regions within device
Erase Block Region 1 Information
(refer to the CFI specification of CFI publication 100)
Erase Block Region 2 Information
Erase Block Region 3 Information
Erase Block Region 4 Information
Table 8. Primary Vendor-specific Extended Query
Adresses
(Word Mode)
40h
41h
42h
43h
44h
Addresses
(Byte Mode)
80h
82h
84h
86h
88h
Data
0050h
0052h
0049h
0031h
0030h
45h
8Ah
0000h
46h
8Ch
0002h
47h
8Eh
0001h
48h
90h
0001h
49h
92h
0004h
4Ah
94h
0000h
4Bh
96h
0000h
4Ch
98h
0000h
Description
Query-unique ASCII string “PRI”
Major version number, ASCII
Minor version number, ASCII
Address Sensitive Unlock
0 = Required, 1 = Not Required
Erase Suspend
0 = Not Supported, 1 = To Read Only, 2 = To Read & Write
Sector Protect
0 = Not Supported, X = Number of sectors in per group
Sector Temporary Unprotect
00 = Not Supported, 01 = Supported
Sector Protect/Unprotect scheme
01 = 29F040 mode, 02 = 29F016 mode,
03 = 29F400 mode, 04 = 29LV800A mode
Simultaneous Operation
00 = Not Supported, 01 = Supported
Burst Mode Type
00 = Not Supported, 01 = Supported
Page Mode Type
00 = Not Supported, 01 = 4 Word Page, 02 = 8 Word Page
This Data Sheet may be revised by subsequent versions
or modifications due to changes in technical specifications.
11
©2004 Eon Silicon Solution, Inc., www.essi.com.tw
Rev. C, Issue Date: 2005/01/07
EN29LV160A
Hardware Data protection
The command sequence requirement of unlock cycles for programming or erasing provides data
protection against inadvertent writes as seen in the Command Definitions table. Additionally, the
following hardware data protection measures prevent accidental erasure or programming, which
might otherwise be caused by false system level signals during Vcc power up and power down
transitions, or from system noise.
Low VCC Write Inhibit
When Vcc is less than VLKO, the device does not accept any write cycles. This protects data during
Vcc power up and power down. The command register and all internal program/erase circuits are
disabled, and the device resets. Subsequent writes are ignored until Vcc is greater than VLKO. The
system must provide the proper signals to the control pins to prevent unintentional writes when Vcc
is greater than VLKO.
Write Pulse “Glitch” protection
Noise pulses of less than 5 ns (typical) on OE#, CE# or WE# do not initiate a write cycle.
Logical Inhibit
Write cycles are inhibited by holding any one of OE# = VIL, CE# = VIH, or WE# = VIH. To initiate a
write cycle, CE# and WE# must be a logical zero while OE# is a logical one. If CE#, WE#, and OE#
are all logical zero (not recommended usage), it will be considered a read.
Power-up Write Inhibit
During power-up, the device automatically resets to READ mode and locks out write cycles. Even
with CE# = VIL, WE#= VIL and OE# = VIH, the device will not accept commands on the rising edge of
WE#.
This Data Sheet may be revised by subsequent versions
or modifications due to changes in technical specifications.
12
©2004 Eon Silicon Solution, Inc., www.essi.com.tw
Rev. C, Issue Date: 2005/01/07
EN29LV160A
COMMAND DEFINITIONS
The operations of the EN29LV160A are selected by one or more commands written into the
command register to perform Read/Reset Memory, Read ID, Read Sector Protection, Program,
Sector Erase, Chip Erase, Erase Suspend and Erase Resume. Commands are made up of data
sequences written at specific addresses via the command register. The sequences for the
specified operation are defined in the Command Definitions table (Table 5). Incorrect addresses,
incorrect data values or improper sequences will reset the device to Read Mode.
Table 9. EN29LV160A Command Definitions
Cycles
Bus Cycles
Command
Sequence
Read
Reset
Autoselect
Manufacturer
ID
1
1
Word
1
RA
xxx
Device ID
Bottom Boot
Word
4
Byte
555
Word
Byte
Word
Unlock Bypass
Byte
Unlock Bypass Program
Unlock Bypass Reset
Word
Chip Erase
Byte
Word
Sector Erase
Byte
Erase Suspend
Erase Resume
Word
CFI Query
Byte
Program
AA
AA
3
2
2
6
6
1
1
1
555
55
2AA
555
2AA
AA
AAA
4
2AA
555
AAA
555
AAA
XXX
XXX
555
AAA
555
AAA
xxx
xxx
55
AA
55
55
AA
A0
90
AA
AA
555
AAA
555
90
555
55
2AA
555
2AA
555
PA
XXX
2AA
555
2AA
555
90
AAA
555
AA
90
AAA
555
2AA
555
4
Byte
Write Cycle
Add
Data
555
AAA
Word
Write Cycle
Add
Data
AA
555
AAA
4th
5
6th
Write Cycle
Add
Data
Write Cycle
Add
Data
Write Cycle
Add
Data
2AA
555
2AA
555
55
555
AAA
10
55
SA
30
3
th
RD
F0
AAA
4
rd
2
Write Cycle
Add
Data
4
Word
Byte
nd
555
Byte
Device ID
Top Boot
Sector Protect
Verify
st
90
AAA
55
55
555
AAA
555
AAA
A0
000
100
000
200
x01
x02
7F
1C
7F
1C
x01
2249
x02
(SA)
X02
(SA)
X04
49
XX00
XX01
00
01
PA
PD
22C4
C4
20
PD
00
55
55
555
AAA
555
AAA
80
80
555
AAA
555
AAA
AA
AA
B0
30
98
Address and Data values indicated in hex
RA = Read Address: address of the memory location to be read. This is a read cycle.
RD = Read Data: data read from location RA during Read operation. This is a read cycle.
PA = Program Address: address of the memory location to be programmed. X = Don’t-Care
PD = Program Data: data to be programmed at location PA
SA = Sector Address: address of the Sector to be erased or verified. Address bits A19-A12 uniquely select any Sector.
Reading Array Data
The device is automatically set to reading array data after power up. No commands are required to
retrieve data. The device is also ready to read array data after completing an Embedded Program
or Embedded Erase algorithm.
Following an Erase Suspend command, Erase Suspend mode is entered. The system can read
array data using the standard read timings, with the only difference in that if it reads at an address
This Data Sheet may be revised by subsequent versions
or modifications due to changes in technical specifications.
13
©2004 Eon Silicon Solution, Inc., www.essi.com.tw
Rev. C, Issue Date: 2005/01/07
EN29LV160A
within erase suspended sectors, the device outputs status data. After completing a programming
operation in the Erase Suspend mode, the system may once again read array data with the same
exception.
The Reset command must be issued to re-enable the device for reading array data if DQ5 goes high,
or while in the autoselect mode. See next section for details on Reset.
Reset Command
Writing the reset command to the device resets the device to reading array data. Address bits are
don’t-care for this command.
The reset command may be written between the sequence cycles in an erase command sequence
before erasing begins. This resets the device to reading array data. Once erasure begins, however,
the device ignores reset commands until the operation is complete. The reset command may be
written between the sequence cycles in a program command sequence before programming begins.
This resets the device to reading array data (also applies to programming in Erase Suspend mode).
Once programming begins, however, the device ignores reset commands until the operation is
complete.
The reset command may be written between the sequence cycles in an autoselect command
sequence. Once in the autoselect mode, the reset command must be written to return to reading
array data (also applies to autoselect during Erase Suspend).
If DQ5 goes high during a program or erase operation, writing the reset command returns the device
to reading array data (also applies during Erase Suspend).
Autoselect Command Sequence
The autoselect command sequence allows the host system to access the manufacturer and devices
codes, and determine whether or not a sector is protected. The Command Definitions table shows
the address and data requirements. This is an alternative to the method that requires VID on
address bit A9 and is intended for PROM programmers.
Two unlock cycles followed by the autoselect command initiate the autoselect command sequence.
Autoselect mode is then entered and the system may read at addresses shown in Table 4 any
number of times, without needing another command sequence.
The system must write the reset command to exit the autoselect mode and return to reading array
data.
Word / Byte Programming Command
The device can be programmed by byte or by word, depending on the state of the Byte# Pin.
Programming the EN29LV160A is performed by using a four-bus-cycle operation (two unlock write
cycles followed by the Program Setup command and Program Data Write cycle). When the program
command is executed, no additional CPU controls or timings are necessary. An internal timer
terminates the program operation automatically. Address is latched on the falling edge of CE# or
WE#, whichever is last; data is latched on the rising edge of CE# or WE#, whichever is first.
Programming status can be checked by sampling data on DQ7 (DATA# polling) or on DQ6 (toggle
bit). When the program operation is successfully completed, the device returns to read mode and
the user can read the data programmed to the device at that address. Note that data can not be
programmed from a “0” to a “1”. Only an erase operation can change a data from “0” to “1”. When
programming time limit is exceeded, DQ5 will produce a logical “1” and a Reset command can
return the device to Read mode.
This Data Sheet may be revised by subsequent versions
or modifications due to changes in technical specifications.
14
©2004 Eon Silicon Solution, Inc., www.essi.com.tw
Rev. C, Issue Date: 2005/01/07
EN29LV160A
Unlock Bypass
To speed up programming operation, the Unlock Bypass Command may be used. Once this feature
is activated, the shorter two cycle Unlock Bypass Program command can be used instead of the
normal four cycle Program Command to program the device. This mode is exited after issuing the
Unlock Bypass Reset Command. The device powers up with this feature disabled.
Chip Erase Command
Chip erase is a six-bus-cycle operation. The chip erase command sequence is initiated by writing
two unlock cycles, followed by a set-up command. Two additional unlock write cycles are then
followed by the chip erase command, which in turn invokes the Embedded Erase algorithm. The
device does not require the system to preprogram prior to erase. The Embedded Erase algorithm
automatically preprograms and verifies the entire memory for an all zero data pattern prior to
electrical erase. The system is not required to provide any controls or timings during these
operations. The Command Definitions table shows the address and data requirements for the chip
erase command sequence.
Any commands written to the chip during the Embedded Chip Erase algorithm are ignored.
The system can determine the status of the erase operation by using DQ7, DQ6, or DQ2. See “Write
Operation Status” for information on these status bits. When the Embedded Erase algorithm is
complete, the device returns to reading array data and addresses are no longer latched.
Flowchart 4 illustrates the algorithm for the erase operation. See the Erase/Program Operations
tables in “AC Characteristics” for parameters, and to the Chip/Sector Erase Operation Timings for
timing waveforms.
Sector Erase Command Sequence
Sector erase is a six bus cycle operation. The sector erase command sequence is initiated by
writing two un-lock cycles, followed by a set-up command. Two additional unlock write cycles are
then followed by the address of the sector to be erased, and the sector erase command. The
Command Definitions table shows the address and data requirements for the sector erase
command sequence.
Once the sector erase operation has begun, only the Erase Suspend command is valid. All other
commands are ignored.
When the Embedded Erase algorithm is complete, the device returns to reading array data and
addresses are no longer latched. The system can determine the status of the erase operation by
using DQ7, DQ6, or DQ2. Refer to “Write Operation Status” for information on these status bits.
Flowchart 4 illustrates the algorithm for the erase operation. Refer to the Erase/Program Operations
tables in the “AC Characteristics” section for parameters, and to the Sector Erase Operations Timing
diagram for timing waveforms.
Erase Suspend / Resume Command
The Erase Suspend command allows the system to interrupt a sector erase operation and then read
data from, or program data to, any sector not selected for erasure. This command is valid only
during the sector erase operation. The Erase Suspend command is ignored if written during the chip
erase operation or Embedded Program algorithm. Addresses are don’t-cares when writing the
Erase Suspend command.
This Data Sheet may be revised by subsequent versions
or modifications due to changes in technical specifications.
15
©2004 Eon Silicon Solution, Inc., www.essi.com.tw
Rev. C, Issue Date: 2005/01/07
EN29LV160A
When the Erase Suspend command is written during a sector erase operation, the device requires a
maximum of 20 µs to suspend the erase operation.
After the erase operation has been suspended, the system can read array data from or program
data to any sector not selected for erasure. (The device “erase suspends” all sectors selected for
erasure.) Normal read and write timings and command definitions apply. Reading at any address
within erase-suspended sectors produces status data on DQ7–DQ0. The system can use DQ7, or
DQ6 and DQ2 together, to determine if a sector is actively erasing or is erase-suspended. See
“Write Operation Status” for information on these status bits.
After an erase-suspended program operation is complete, the system can once again read array
data within non-suspended sectors. The system can determine the status of the program operation
using the DQ7 or DQ6 status bits, just as in the standard program operation. See “Write Operation
Status” for more information. The Autoselect command is not supported during Erase Suspend
Mode.
The system must write the Erase Resume command (address bits are don’t-care) to exit the erase
suspend mode and continue the sector erase operation. Further writes of the Resume command are
ignored. Another Erase Suspend command can be written after the device has resumed erasing.
WRITE OPERATION STATUS
DQ7
DATA# Polling
The EN29LV160A provides DATA# polling on DQ7 to indicate the status of the embedded
operations. The DATA# polling feature is active during Byte Programming, Sector Erase, Chip
Erase, and Erase Suspend. (See Table 10)
When the embedded Programming is in progress, an attempt to read the device will produce the
complement of the data written to DQ7. Upon the completion of the Byte Programming, an attempt
to read the device will produce the true data written to DQ7. For the Byte Programming, DATA#
polling is valid after the rising edge of the fourth WE# or CE# pulse in the four-cycle sequence.
When the embedded Erase is in progress, an attempt to read the device will produce a “0” at the
DQ7 output. Upon the completion of the embedded Erase, the device will produce the “1” at the DQ7
output during the read cycles. For Chip Erase, the DATA# polling is valid after the rising edge of the
sixth WE# or CE# pulse in the six-cycle sequence. DATA# polling is valid after the last rising edge of
the WE# or CE# pulse for chip erase or sector erase.
DATA# Polling must be performed at any address within a sector that is being programmed or
erased and not a protected sector. Otherwise, DATA# polling may give an inaccurate result if the
address used is in a protected sector.
Just prior to the completion of the embedded operations, DQ7 may change asynchronously when
the output enable (OE#) is low. This means that the device is driving status information on DQ7 at
one instant of time and valid data at the next instant of time. Depending on when the system
samples the DQ7 output, it may read the status of valid data. Even if the device has completed the
embedded operations and DQ7 has a valid data, the data output on DQ0-DQ6 may be still invalid.
The valid data on DQ0-DQ7 will be read on the subsequent read attempts.
The flowchart for DATA# Polling (DQ7) is shown on Flowchart 5. The DATA# Polling (DQ7) timing
diagram is shown in Figure 8.
RY/BY#: Ready/Busy
This Data Sheet may be revised by subsequent versions
or modifications due to changes in technical specifications.
16
©2004 Eon Silicon Solution, Inc., www.essi.com.tw
Rev. C, Issue Date: 2005/01/07
EN29LV160A
The RY/BY# is a dedicated, open-drain output pin that indicates whether an Embedded Algorithm is
in progress or completed. The RY/BY# status is valid after the rising edge of the final WE# pulse in
the command sequence. Since RY/BY# is an open-drain output, several RY/BY# pins can be tied
together in parallel with a pull-up resistor to Vcc.
In the output-low period, signifying Busy, the device is actively erasing or programming. This
includes programming in the Erase Suspend mode. If the output is high, signifying the Ready, the
device is ready to read array data (including during the Erase Suspend mode), or is in the standby
mode.
DQ6
Toggle Bit I
The EN29LV160A provides a “Toggle Bit” on DQ6 to indicate the status of the embedded
programming and erase operations. (See Table 6)
During an embedded Program or Erase operation, successive attempts to read data from the device
at any address (by active OE# or CE#) will result in DQ6 toggling between “zero” and “one”. Once
the embedded Program or Erase operation is completed, DQ6 will stop toggling and valid data will
be read on the next successive attempts. During embedded Programming, the Toggle Bit is valid
after the rising edge of the fourth WE# pulse in the four-cycle sequence. During Erase operation, the
Toggle Bit is valid after the rising edge of the sixth WE# pulse for sector erase or chip erase.
In embedded Programming, if the sector being written to is protected, DQ6 will toggles for about 2
µs, then stop toggling without the data in the sector having changed. In Sector Erase or Chip Erase,
if all selected sectors are protected, DQ6 will toggle for about 100 µs. The chip will then return to the
read mode without changing data in all protected sectors.
The flowchart for the Toggle Bit (DQ6) is shown in Flowchart 6. The Toggle Bit timing diagram is
shown in Figure 9.
DQ5 Exceeded Timing Limits
DQ5 indicates whether the program or erase time has exceeded a specified internal pulse count
limit. Under these conditions DQ5 produces a “1.” This is a failure condition that indicates the
program or erase cycle was not successfully completed. Since it is possible that DQ5 can become a
1 when the device has successfully completed its operation and has returned to read mode, the user
must check again to see if the DQ6 is toggling after detecting a “1” on DQ5.
The DQ5 failure condition may appear if the system tries to program a “1” to a location that is
previously programmed to “0.” Only an erase operation can change a “0” back to a “1.” Under
this condition, the device halts the operation, and when the operation has exceeded the timing limits,
DQ5 produces a “1.” Under both these conditions, the system must issue the reset command to
return the device to reading array data.
DQ3 Sector Erase Timer
After writing a sector erase command sequence, the output on DQ3 can be used to determine
whether or not an erase operation has begun. (The sector erase timer does not apply to the chip
erase command.) When sector erase starts, DQ3 switches from “0” to “1.” This device does not
support multiple sector erase command sequences so it is not very meaningful since it immediately
shows as a “1” after the first 30h command. Future devices may support this feature.
DQ2 Erase Toggle Bit II
This Data Sheet may be revised by subsequent versions
or modifications due to changes in technical specifications.
17
©2004 Eon Silicon Solution, Inc., www.essi.com.tw
Rev. C, Issue Date: 2005/01/07
EN29LV160A
The “Toggle Bit” on DQ2, when used with DQ6, indicates whether a particular sector is actively
erasing (that is, the Embedded Erase algorithm is in progress), or whether that sector is erasesuspended. Toggle Bit II is valid after the rising edge of the final WE# pulse in the command
sequence. DQ2 toggles when the system reads at addresses within those sectors that have been
selected for erasure. (The system may use either OE# or CE# to control the read cycles.) But DQ2
cannot distinguish whether the sector is actively erasing or is erase-suspended. DQ6, by
comparison, indicates whether the device is actively erasing, or is in Erase Suspend, but cannot
distinguish which sectors are selected for erasure. Thus, both status bits are required for sector and
mode information. Refer to Table 5 to compare outputs for DQ2 and DQ6.
Flowchart 6 shows the toggle bit algorithm, and the section “DQ2: Toggle Bit” explains the algorithm.
See also the “DQ6: Toggle Bit I” subsection. Refer to the Toggle Bit Timings figure for the toggle bit
timing diagram. The DQ2 vs. DQ6 figure shows the differences between DQ2 and DQ6 in graphical
form.
Reading Toggle Bits DQ6/DQ2
Refer to Flowchart 6 for the following discussion. Whenever the system initially begins reading
toggle bit status, it must read DQ7–DQ0 at least twice in a row to determine whether a toggle bit is
toggling. Typically, a system would note and store the value of the toggle bit after the first read. After
the second read, the system would compare the new value of the toggle bit with the first. If the
toggle bit is not toggling, the device has completed the program or erase operation. The system can
read array data on DQ7–DQ0 on the following read cycle.
However, if after the initial two read cycles, the system determines that the toggle bit is still toggling,
the system also should note whether the value of DQ5 is high (see the section on DQ5). If it is, the
system should then determine again whether the toggle bit is toggling, since the toggle bit may have
stopped toggling just as DQ5 went high. If the toggle bit is no longer toggling, the device has
successfully completed the program or erase operation. If it is still toggling, the device did not
complete the operation successfully, and the system must write the reset command to return to
reading array data.
The remaining scenario is that the system initially determines that the toggle bit is toggling and DQ5
has not gone high. The system may continue to monitor the toggle bit and DQ5 through successive
read cycles, determining the status as described in the previous paragraph. Alternatively, it may
choose to perform other system tasks. In this case, the system must start at the beginning of the
algorithm when it returns to determine the status of the operation (top of Flowchart 6).
Write Operation Status
Standar
d Mode
Erase
Suspend
Mode
Operation
DQ7
DQ6
DQ5
DQ3
DQ2
RY/BY
#
Embedded Program
Algorithm
DQ7#
Toggle
0
N/A
No
toggle
0
Embedded Erase Algorithm
0
Toggle
0
1
Toggle
0
1
No
Toggle
0
N/A
Toggle
1
Data
Data
Data
Data
Data
1
DQ7#
Toggle
0
N/A
N/A
0
Reading within Erase
Suspended Sector
Reading within Non-Erase
Suspended Sector
Erase-Suspend Program
This Data Sheet may be revised by subsequent versions
or modifications due to changes in technical specifications.
18
©2004 Eon Silicon Solution, Inc., www.essi.com.tw
Rev. C, Issue Date: 2005/01/07
EN29LV160A
Table 10. Status Register Bits
DQ
Name
Logic Level
‘1’
‘0’
7
6
DATA#
POLLING
TOGGLE
BIT
DQ7
Definition
Erase Complete or
erase Sector in Erase suspend
Erase On-Going
Program Complete or
data of non-erase Sector
during Erase Suspend
DQ7#
‘-1-0-1-0-1-0-1-’
DQ6
Program On-Going
Erase or Program On-going
Read during Erase Suspend
Erase Complete
‘-1-1-1-1-1-1-1-‘
5
ERROR BIT
3
ERASE
TIME BIT
2
TOGGLE
BIT
‘1’
‘0’
‘1’
‘0’
Program or Erase Error
Program or Erase On-going
Erase operation start
Erase timeout period on-going
Chip Erase, Erase or Erase
suspend on currently
addressed
Sector. (When DQ5=1, Erase
Error due to currently
addressed Sector. Program
during Erase Suspend ongoing at current address
‘-1-0-1-0-1-0-1-’
Erase Suspend read on
non Erase Suspend Sector
DQ2
Notes:
DQ7 DATA# Polling: indicates the P/E status check during Program or Erase, and on completion before checking bits DQ5
for Program or Erase Success.
DQ6 Toggle Bit: remains at constant level when P/E operations are complete or erase suspend is acknowledged.
Successive reads output complementary data on DQ6 while programming or Erase operation are on-going.
DQ5 Error Bit: set to “1” if failure in programming or erase
DQ3 Sector Erase Command Timeout Bit: Operation has started. Only possible command is Erase suspend (ES).
DQ2 Toggle Bit: indicates the Erase status and allows identification of the erased Sector.
This Data Sheet may be revised by subsequent versions
or modifications due to changes in technical specifications.
19
©2004 Eon Silicon Solution, Inc., www.essi.com.tw
Rev. C, Issue Date: 2005/01/07
EN29LV160A
EMBEDDED ALGORITHMS
Flowchart 1. Embedded Program
START
Write Program
Command Sequence
(shown below)
Data# Poll Device
Verify Data?
Increment
Address
Last
No
Address?
Yes
Programming Done
Flowchart 2. Embedded Program Command Sequence
See the Command Definitions section for more information.
555H / AAH
2AAH / 55H
555H / A0H
PROGRAM ADDRESS / PROGRAM DATA
This Data Sheet may be revised by subsequent versions
or modifications due to changes in technical specifications.
20
©2004 Eon Silicon Solution, Inc., www.essi.com.tw
Rev. C, Issue Date: 2005/01/07
EN29LV160A
Flowchart 3. Embedded Erase
START
Write Erase
Command Sequence
Data# Poll from
System or Toggle Bit
successfully
completed
Data =FFh?
No
Yes
Erase Done
Flowchart 4. Embedded Erase Command Sequence
See the Command Definitions section for more information.
Chip Erase
Sector Erase
555H/AAH
555H/AAH
2AAH/55H
2AAH/55H
555H/80H
555H/80H
555H/AAH
555H/AAH
2AAH/55H
2AAH/55H
555H/10H
Sector Address/30H
This Data Sheet may be revised by subsequent versions
or modifications due to changes in technical specifications.
21
©2004 Eon Silicon Solution, Inc., www.essi.com.tw
Rev. C, Issue Date: 2005/01/07
EN29LV160A
Flowchart 5. DATA# Polling
Algorithm
Start
Read Data
DQ7 = Data?
Yes
No
No
DQ5 = 1?
Yes
Read Data (1)
Notes:
(1) This second read is necessary in case the
first read was done at the exact instant when
the status data was in transition.
Yes
DQ7 = Data?
No
Fail
Pass
Start
Flowchart 6. Toggle Bit Algorithm
Read Data twice
No
DQ6 = Toggle?
Yes
No
DQ5 = 1?
Yes
Read Data twice (2)
Notes:
(2) This second set of reads is necessary in case
the first set of reads was done at the exact
instant when the status data was in transition.
No
DQ6 = Toggle?
Yes
Fail
This Data Sheet may be revised by subsequent versions
or modifications due to changes in technical specifications.
22
Pass
©2004 Eon Silicon Solution, Inc., www.essi.com.tw
Rev. C, Issue Date: 2005/01/07
EN29LV160A
Flowchart 7a. In-System Sector Protect Flowchart
START
PLSCNT = 1
RESET# = VID
Wait 1 µs
No
First Write
Cycle =
60h?
Temporary Sector
Unprotect Mode
Yes
Set up sector
address
Sector Protect: Write 60h
to sector addr with
A6 = 0, A1 = 1, A0 = 0
Wait 150 µs
Verify Sector Protect:
Write 40h to sector
address with
A6 = 0, A1 = 1, A0 = 0
Increment
PLSCNT
Reset
PLSCNT = 1
Wait 0.4 µs
Read from sector
address with
A6 = 0, A1 = 1, A0
No
No
PLSCNT = 25?
Data = 01h?
Yes
Yes
Device failed
Protect another
sector?
Yes
No
Remove VID
from RESET#
Write reset
command
Sector Protect
Algorithm
Sector Protect
complete
This Data Sheet may be revised by subsequent versions
or modifications due to changes in technical specifications.
23
©2004 Eon Silicon Solution, Inc., www.essi.com.tw
Rev. C, Issue Date: 2005/01/07
EN29LV160A
Flowchart 7b. In-System Sector Unprotect Flowchart
START
PLSCNT = 1
Protect all sectors:
The indicated portion
of the sector protect
algorithm must be
performed for all
unprotected sectors
prior to issuing the
first sector unprotect
address (see
Diagram 7a.)
RESET# = VID
Wait 1 µS
No
Temporary Sector
Unprotect Mode
First Write
Cycle = 60h?
Yes
No
All sectors
protected?
Yes
Set up first sector
address
Sector Unprotect: Write 60H to
sector address with A6 = 1,
A1 = 1, A0 = 0
Wait 15 ms
Increment
PLSCNT
Verify Sector Unprotect:
Write 40h to sector address
with A6 = 1, A1 = 1, A0 =0
Wait 0.4 µS
No
PLSCCNT =
1000?
Sector
Unprotect
Algorithm
Read from sector address with
A6 = 1, A1 = 1, A0 = 0
No
Yes
Yes
Device failed
Set up next sector
address
Data = 00h?
Last sector
verified?
No
Yes
Remove VID from
RESET#
This Data Sheet may be revised by subsequent versions
or modifications due to changes in technical specifications.
24
Write reset
command
Sector Unprotect
complete
©2004 Eon Silicon Solution, Inc., www.essi.com.tw
Rev. C, Issue Date: 2005/01/07
EN29LV160A
Table 11. DC Characteristics
(Ta = 0°C to 70°C or - 40°C to 85°C; VCC = 2.7-3.6V)
Symbol
Parameter
Test Conditions
ILI
Input Leakage Current
ILO
Output Leakage Current
Supply Current (read) CMOS Byte
ICC1
(read) CMOS Word
Supply Current (Standby - TTL)
ICC2
(Standby - CMOS)
ICC3
Supply Current (Program or Erase)
VIL
Input Low Voltage
VIH
Input High Voltage
VOL
Output Low Voltage
Min
Max
Unit
0V≤ VIN ≤ Vcc
±5
µA
0V≤ VOUT ≤ Vcc
±5
µA
9
16
mA
9
16
mA
0.4
1.0
mA
1
5.0
µA
20
30
mA
0.8
Vcc ±
0.3
0.45
V
CE# = VIL ; OE# = VIH ;
f = 5MHZ
CE# = VIH,
BYTE# = RESET# =
Vcc ± 0.3V
(Note 1)
CE# = BYTE# =
RESET# = Vcc ± 0.3V
(Note 1)
Byte program, Sector or
Chip Erase in progress
-0.5
0.7 x
Vcc
IOL = 4.0 mA
Output High Voltage TTL
IOH = -2.0 mA
Output High Voltage CMOS
IOH = -100 µA,
VOH
VID
A9 Voltage (Electronic Signature)
IID
A9 Current (Electronic Signature)
VLKO
Supply voltage (Erase and
Program lock-out)
0.85 x
Vcc
Vcc 0.4V
10.5
A9 = VID
2.3
Typ
V
11.5
V
100
µA
2.5
V
1. BYTE# pin can also be GND ± 0.3V. BYTE# and RESET# pin input buffers are always enabled so that
they draw power if not at full CMOS supply voltages.
25
©2004 Eon Silicon Solution, Inc., www.essi.com.tw
Rev. C, Issue Date: 2005/01/07
V
V
Notes
This Data Sheet may be revised by subsequent versions
or modifications due to changes in technical specifications.
V
EN29LV160A
Test Conditions
3.3 V
2.7 kΩ
Device Under Test
CL
6.2 kΩ
Note: Diodes are IN3064 or equivalent
Test Specifications
Test Conditions
-70
Output Load
-90
Unit
1 TTL Gate
Output Load Capacitance, CL
30
100
pF
Input Rise and Fall times
5
5
ns
Input Pulse Levels
Input timing measurement
reference levels
Output timing measurement
reference levels
0.0-3.0
0.0-3.0
V
1.5
1.5
V
1.5
1.5
V
This Data Sheet may be revised by subsequent versions
or modifications due to changes in technical specifications.
26
©2004 Eon Silicon Solution, Inc., www.essi.com.tw
Rev. C, Issue Date: 2005/01/07
EN29LV160A
AC CHARACTERISTICS
Hardware Reset (Reset#)
Parameter
Std
tREADY
tREADY
tRP
tRH
Description
Reset# Pin Low to Read or Write
Embedded Algorithms
Reset# Pin Low to Read or Write
Non Embedded Algorithms
Reset# Pulse Width
Reset# High Time Before Read
Test
Setup
Speed options
-70
-90
Unit
Max
20
µs
Max
500
nS
Min
Min
500
50
nS
nS
Reset# Timings
RY/BY#
0V
CE#
OE#
tRH
RESET#
tRP
tREADY
Reset Timings NOT During Automatic Algorithms
RY/BY#
tREADY
CE#
OE#
RESET#
tRP
tRH
Reset Timings During Automatic Algorithms
This Data Sheet may be revised by subsequent versions
or modifications due to changes in technical specifications.
27
©2004 Eon Silicon Solution, Inc., www.essi.com.tw
Rev. C, Issue Date: 2005/01/07
EN29LV160A
AC CHARACTERISTICS
Word / Byte Configuration (Byte#)
Std
Parameter
tBCS
tCBH
tRBH
Speed
Description
Byte# to CE# switching setup time
CE# to Byte# switching hold time
RY/BY# to Byte# switching hold time
Min
Min
Min
-70
0
0
0
-90
0
0
0
CE#
OE#
Byte#
tCBH
tBCS
Byte# timings for Read Operations
CE#
WE#
Byte#
tRBH
tBCS
RY/BY#
Byte #timings for Write Operations
Note: Switching BYTE# pin not allowed during embedded operations
This Data Sheet may be revised by subsequent versions
or modifications due to changes in technical specifications.
28
©2004 Eon Silicon Solution, Inc., www.essi.com.tw
Rev. C, Issue Date: 2005/01/07
Unit
ns
ns
ns
EN29LV160A
Table 12. AC CHARACTERISTICS
Read-only Operations Characteristics
Parameter
Symbols
JEDEC
Standard
Description
tAVAV
tRC
Read Cycle Time
tAVQV
tACC
Address to Output Delay
tELQV
tCE
Chip Enable To Output Delay
tGLQV
tOE
tEHQZ
Speed Options
Test
Setup
Min
-70
70
-90
90
Unit
ns
CE# = VIL
OE#= VIL
Max
70
90
ns
OE#= VIL
Max
70
90
ns
Output Enable to Output Delay
Max
30
35
ns
tDF
Chip Enable to Output High Z
Max
20
20
ns
tGHQZ
tDF
Output Enable to Output High Z
Max
20
20
ns
tAXQX
tOH
Output Hold Time from
Addresses, CE# or OE#,
whichever occurs first
Min
0
0
ns
Notes:
For - 70
Vcc = 3.0V ± 5%
Output Load : 1 TTL gate and 30pF
Input Rise and Fall Times: 5ns
Input Rise Levels: 0.0 V to 3.0 V
Timing Measurement Reference Level, Input and Output: 1.5 V
For all others:
Vcc = 2.7V – 3.6V
Output Load: 1 TTL gate and 100 pF
Input Rise and Fall Times: 5 ns
Input Pulse Levels: 0.45 V to .8 x Vcc
Timing Measurement Reference Level, Input and Output: 0.8 V and .7 x Vcc
tRC
Addresses Stable
Addresses
tACC
CE#
tDF
tOE
OE#
tOEH
WE#
tCE
tOH
Output Valid
Outputs
HIGH Z
Reset#
RY/BY#
0V
Figure 5. AC Waveforms for READ Operations
This Data Sheet may be revised by subsequent versions
or modifications due to changes in technical specifications.
29
©2004 Eon Silicon Solution, Inc., www.essi.com.tw
Rev. C, Issue Date: 2005/01/07
EN29LV160A
Table 13. AC CHARACTERISTICS
Write (Erase/Program) Operations
Parameter
Symbols
Speed Options
JEDEC
Standard
Description
-70
-90
Unit
tAVAV
tWC
Write Cycle Time
Min
70
90
ns
tAVWL
tAS
Address Setup Time
Min
0
0
ns
tWLAX
tAH
Address Hold Time
Min
45
45
ns
tDVWH
tDS
Data Setup Time
Min
30
45
ns
tWHDX
tDH
Data Hold Time
Min
0
0
ns
tOES
Output Enable Setup Time
Min
0
0
ns
MIn
0
0
ns
Min
10
10
ns
Min
0
0
ns
tGHWL
tGHWL
Read
Toggle and
DATA# Polling
Read Recovery Time before
Write (OE# High to WE# Low)
tELWL
tCS
CE# SetupTime
Min
0
0
ns
tWHEH
tCH
CE# Hold Time
Min
0
0
ns
tWLWH
tWP
Write Pulse Width
Min
45
45
ns
tWHDL
tWPH
Write Pulse Width High
Min
20
20
ns
tWHWH1
tWHWH1
Programming Operation
(Word AND Byte Mode)
Typ
8
8
µs
Max
300
300
µs
Typ
0.5
0.5
s
Max
10
10
s
tOEH
Output Enable
Hold Time
tWHWH2
tWHWH2
Sector Erase Operation
tWHWH3
tWHWH3
Chip Erase Operation
Typ
17.5
17.5
s
tVCS
Vcc Setup Time
Min
50
50
µs
tVIDR
Rise Time to VID
Min
500
500
ns
This Data Sheet may be revised by subsequent versions
or modifications due to changes in technical specifications.
30
©2004 Eon Silicon Solution, Inc., www.essi.com.tw
Rev. C, Issue Date: 2005/01/07
EN29LV160A
Table 14. AC CHARACTERISTICS
Write (Erase/Program) Operations
Alternate CE# Controlled Writes
Parameter
Symbols
JEDEC
Standard
Speed Options
Description
-70
-90
Unit
tAVAV
tWC
Write Cycle Time
Min
70
90
ns
tAVEL
tAS
Address Setup Time
Min
0
0
ns
tELAX
tAH
Address Hold Time
Min
45
45
ns
tDVEH
tDS
Data Setup Time
Min
30
45
ns
tEHDX
tDH
Data Hold Time
Min
0
0
ns
tOES
Output Enable Setup Time
Min
0
0
ns
0
0
0
ns
10
10
10
ns
Min
0
0
ns
tOEH
Output Enable
tGHEL
tGHEL
Read
Toggle and
Hold Time
Data Polling
Read Recovery Time before
Write (OE# High to CE# Low)
tWLEL
tWS
WE# SetupTime
Min
0
0
ns
tEHWH
tWH
WE# Hold Time
Min
0
0
ns
tELEH
tCP
Write Pulse Width
Min
35
45
ns
tEHEL
tCPH
Write Pulse Width High
Min
20
20
ns
tWHWH1
tWHWH1
Programming Operation
(Byte AND word mode)
Typ
8
8
µs
Max
300
300
µs
tWHWH2
tWHWH2
Typ
0.5
0.5
s
Sector Erase Operation
Max
10
10
s
tWHWH3
tWHWH3
Typ
17.5
17.5
s
Chip Erase Operation
tVCS
Vcc Setup Time
Min
50
50
µs
tVIDR
Rise Time to VID
Min
500
500
ns
This Data Sheet may be revised by subsequent versions
or modifications due to changes in technical specifications.
Max
31
s
©2004 Eon Silicon Solution, Inc., www.essi.com.tw
Rev. C, Issue Date: 2005/01/07
EN29LV160A
TABLE 15. ERASE AND PROGRAMMING PERFORMANCE
Typ
Limits
Max
Unit
Sector Erase Time
0.5
10
sec
Chip Erase Time
17.5
Byte Programming Time
8
300
µs
Word Programming Time
8
300
µs
Byte
16.8
50.4
Word
8.4
25.2
Parameter
Chip Programming
Time
Erase/Program Endurance
Comments
Excludes 00H programming prior
to erasure
sec
Excludes system level overhead
sec
1000K
Minimum 1000K cycles
cycles
Table 16. LATCH UP CHARACTERISTICS
Parameter Description
Min
Max
Input voltage with respect to Vss on all pins except I/O pins
(including A9, Reset and OE#)
-1.0 V
12.0 V
Input voltage with respect to Vss on all I/O Pins
-1.0 V
Vcc + 1.0 V
Vcc Current
-100 mA
100 mA
Note : These are latch up characteristics and the device should never be put under
these conditions. Refer to Absolute Maximum ratings for the actual operating limits.
Table 17. 48-PIN TSOP PIN CAPACITANCE @ 25°C, 1.0MHz
Parameter Symbol
Parameter Description
Test Setup
Typ
Max
Unit
CIN
Input Capacitance
VIN = 0
6
7.5
pF
COUT
Output Capacitance
VOUT = 0
8.5
12
pF
CIN2
Control Pin Capacitance
VIN = 0
7.5
9
pF
Table 18. DATA RETENTION
Parameter Description
Test Conditions
Min
Unit
150°C
10
Years
125°C
20
Years
Minimum Pattern Data Retention Time
This Data Sheet may be revised by subsequent versions
or modifications due to changes in technical specifications.
32
©2004 Eon Silicon Solution, Inc., www.essi.com.tw
Rev. C, Issue Date: 2005/01/07
EN29LV160A
AC CHARACTERISTICS
Figure 6. AC Waveforms for Chip/Sector Erase Operations Timings
Erase Command Sequence (last 2 cycles)
tWC
Addresses
tAS
0x2AA
Read Status Data (last two cycles)
tAH
SA
VA
VA
0x555 for chip
erase
CE#
tGHWL
tCH
OE#
tWP
WE#
tCS
tWPH
tWHWH2 or tWHWH3
0x55
Data
tDS
0x30
tDH
Status
tBUSY
DOUT
tRB
RY/BY#
VCC
tVCS
Notes:
1. SA=Sector Address (for sector erase), VA=Valid Address for reading status, Dout=true data at read address.
2. Vcc shown only to illustrate tvcs measurement references. It cannot occur as shown during a valid command
sequence.
This Data Sheet may be revised by subsequent versions
or modifications due to changes in technical specifications.
33
©2004 Eon Silicon Solution, Inc., www.essi.com.tw
Rev. C, Issue Date: 2005/01/07
EN29LV160A
Figure 7. Program Operation Timings
Program Command Sequence (last 2 cycles)
tWC
Addresses
tAS
0x555
Program Command Sequence (last 2 cycles)
tAH
PA
PA
PA
CE#
tGHWL
tWP
OE#
WE#
tCH
tWPH
tCS
tWHWH1
Data
PD
OxA0
Status
DOUT
tDS
tRB
tBUSY
tDH
RY/BY#
tVCS
VCC
Notes:
1. PA=Program Address, PD=Program Data, DOUT is the true data at the program address.
2. VCC shown in order to illustrate tVCS measurement references. It cannot occur as shown during a valid
command sequence.
This Data Sheet may be revised by subsequent versions
or modifications due to changes in technical specifications.
34
©2004 Eon Silicon Solution, Inc., www.essi.com.tw
Rev. C, Issue Date: 2005/01/07
EN29LV160A
Figure 8. AC Waveforms for /DATA Polling During Embedded Algorithm
Operations
tRC
Addresses
VA
VA
VA
tACC
tCH
tCE
CE#
tOE
OE#
tOEH
tDF
WE#
tOH
DQ[7]
Complement
DQ[6:0]
Complement
Status
Data
Status Data
True
Valid Data
True
Valid Data
tBUSY
RY/BY#
Notes:
1. VA=Valid Address for reading Data# Polling status data
2. This diagram shows the first status cycle after the command sequence, the last status read cycle and the array data read cycle.
Figure 9. AC Waveforms for Toggle Bit During Embedded Algorithm
Operations
tRC
Addresses
VA
VA
VA
VA
tACC
tCH
tCE
CE#
tOE
OE#
tOEH
WE#
tDF
tOH
Valid Status
DQ6, DQ2
tBUSY
(first read)
Valid Status
(second
d)
Valid Status
Valid Data
(stops toggling)
RY/BY#
This Data Sheet may be revised by subsequent versions
or modifications due to changes in technical specifications.
35
©2004 Eon Silicon Solution, Inc., www.essi.com.tw
Rev. C, Issue Date: 2005/01/07
EN29LV160A
Figure 10. Alternate CE# Controlled Write Operation Timings
0x555 for Program
0x2AA for Erase
PA for Program
SA for Sector Erase
0x555 for Chip Erase
Addresses
VA
tWC
tAS
tAH
WE#
tWH
tGHEL
OE#
tCP
tWS
tCPH
tCWHWH1 / tCWHWH2 / tCWHWH3
CE#
tDS
tBUSY
tDH
Data
Status
DOUT
PD for Program
0x30 for Sector Erase
0x10 for Chip Erase
0xA0 for
Program
RY/BY#
tRH
Reset#
Notes:
PA = address of the memory location to be programmed.
PD = data to be programmed at byte address.
VA = Valid Address for reading program or erase status
Dout = array data read at VA
Shown above are the last two cycles of the program or erase command sequence and the last status read cycle
Reset# shown to illustrate tRH measurement references. It cannot occur as shown during a valid command
sequence.
Figure 11. DQ2 vs. DQ6
Enter
Embedded
Erase
WE#
Enter Erase
Suspend
Program
Erase
Suspend
Erase
Erase
Resume
Enter
Suspend
Program
Enter
Suspend
Read
Erase
Suspend
Read
Erase
DQ6
DQ2
This Data Sheet may be revised by subsequent versions
or modifications due to changes in technical specifications.
36
©2004 Eon Silicon Solution, Inc., www.essi.com.tw
Rev. C, Issue Date: 2005/01/07
Erase
Complete
EN29LV160A
Temporary Sector Unprotect
Parameter
Std
tVIDR
VID Rise and Fall Time
RESET# Setup Time for Temporary
Sector Unprotect
tRSP
Speed Option
-70
-90
Unit
Min
500
Ns
Min
4
µs
Description
Figure 12. Temporary Sector Unprotect Timing Diagram
VID
RESET#
0 or 3 V
0 or 3 V
tVIDR
tVIDR
CE#
WE#
tRSP
RY/BY#
Figure 13. Sector Protect/Unprotect Timing Diagram
VID
RESET#
Vcc
0V
0V
tVIDR
tVIDR
SA,
A6,A1,A0
Data
60h
Valid
Valid
Valid
60h
40h
Status
Sector Protect/Unprotect
Verify
CE#
>0.4µS
WE#
>1µS
Sector Protect: 150 uS
Sector Unprotect: 15 mS
OE#
Notes:
Use standard microprocessor timings for this device for read and write cycles.
For Sector Protect, use A6=0, A1=1, A0=0. For Sector Unprotect, use A6=1, A1=1, A0=0.
This Data Sheet may be revised by subsequent versions
or modifications due to changes in technical specifications.
37
©2004 Eon Silicon Solution, Inc., www.essi.com.tw
Rev. C, Issue Date: 2005/01/07
EN29LV160A
FIGURE 14. TSOP 12mm x 20mm
This Data Sheet may be revised by subsequent versions
or modifications due to changes in technical specifications.
38
©2004 Eon Silicon Solution, Inc., www.essi.com.tw
Rev. C, Issue Date: 2005/01/07
EN29LV160A
This Data Sheet may be revised by subsequent versions
or modifications due to changes in technical specifications.
39
©2004 Eon Silicon Solution, Inc., www.essi.com.tw
Rev. C, Issue Date: 2005/01/07
EN29LV160A
FIGURE 15. 48TFBGA package outline
This Data Sheet may be revised by subsequent versions
or modifications due to changes in technical specifications.
40
©2004 Eon Silicon Solution, Inc., www.essi.com.tw
Rev. C, Issue Date: 2005/01/07
EN29LV160A
ABSOLUTE MAXIMUM RATINGS
Parameter
Value
Unit
Storage Temperature
-65 to +125
°C
Plastic Packages
-65 to +125
°C
-55 to +125
°C
200
MA
A9, OE#, Reset# 2
-0.5 to +11.5
V
All other pins 3
-0.5 to Vcc+0.5
V
Vcc
-0.5 to +4.0
V
Ambient Temperature
With Power Applied
Output Short Circuit Current1
Voltage with
Respect to Ground
Notes:
1.
No more than one output shorted at a time. Duration of the short circuit should not be greater than one second.
2.
Minimum DC input voltage on A9, OE#, RESET# pins is –0.5V. During voltage transitions, A9, OE#, RESET# pins may
undershoot Vss to –1.0V for periods of up to 50ns and to –2.0V for periods of up to 20ns. See figure below. Maximum DC
input voltage on A9, OE#, and RESET# is 11.5V which may overshoot to 12.5V for periods up to 20ns.
3.
Minimum DC voltage on input or I/O pins is –0.5 V. During voltage transitions, inputs may undershoot Vss to –1.0V for
periods of up to 50ns and to –2.0 V for periods of up to 20ns. See figure below. Maximum DC voltage on output and I/O
pins is Vcc + 0.5 V. During voltage transitions, outputs may overshoot to Vcc + 1.5 V for periods up to 20ns. See figure
below.
4.
Stresses above the values so mentioned above may cause permanent damage to the device. These values are for a stress
rating only and do not imply that the device should be operated at conditions up to or above these values. Exposure of the
device to the maximum rating values for extended periods of time may adversely affect the device reliability.
RECOMMENDED OPERATING RANGES1
Parameter
Ambient Operating Temperature
Commercial Devices
Industrial Devices
Value
Unit
0 to 70
-40 to 85
°C
Regulated Voltage
Range: 3.0-3.6V
Operating Supply Voltage
Vcc
V
Full Voltage Range: 2.7 to
3.6V
1.
Recommended Operating Ranges define those limits between which the functionality of the device is guaranteed.
Vcc
+1.5V
Maximum Negative Overshoot
Waveform
This Data Sheet may be revised by subsequent versions
or modifications due to changes in technical specifications.
Maximum Positive Overshoot
Waveform
41
©2004 Eon Silicon Solution, Inc., www.essi.com.tw
Rev. C, Issue Date: 2005/01/07
EN29LV160A
ORDERING INFORMATION
EN29LV160A
T
-
70
T
C
P
PACKAGING CONTENT
(Blank) = Conventional
P = Pb Free
TEMPERATURE RANGE
C = Commercial (0°C to +70°C)
I = Industrial (-40°C to +85°C)
PACKAGE
T = 48-pin TSOP
B = 48-Ball Fine Pitch Ball Grid Array (FBGA)
0.80mm pitch, 6mm x 8mm package
SPEED
70 = 70ns
90 = 90ns
BOOT CODE SECTOR ARCHITECTURE
T = Top boot Sector
B = Bottom boot Sector
BASE PART NUMBER
EN = Eon Silicon Solution Inc.
29LV = FLASH, 3V Read Program Erase
160 = 16 Megabit (2M x 8 / 1M x 16)
A = version identifier
This Data Sheet may be revised by subsequent versions
or modifications due to changes in technical specifications.
42
©2004 Eon Silicon Solution, Inc., www.essi.com.tw
Rev. C, Issue Date: 2005/01/07
EN29LV160A
Revisions List
Revision No
Description
Date
A
B
Preliminary draft
Initial Release
1. Update Eon logo.
2. Correct a typo on page 39, dimension E and N corrected.
2004/10/01
2004/11/26
C
This Data Sheet may be revised by subsequent versions
or modifications due to changes in technical specifications.
43
2005/01/07
©2004 Eon Silicon Solution, Inc., www.essi.com.tw
Rev. C, Issue Date: 2005/01/07
Similar pages