White Electronic Designs Display Systems Division ENH064V1-800 ENH064V1-800 Color TFT-LCD Module Features GENERAL DESCRIPTION WEDC provides optically enhanced solutions to the standard Sharp LQ64D343 color active matrix LCD module. The ENH064V1-800 enhancement is an index matching (IM) film lamination to the front surface of the display polarizer. The IM film is available in two surface treatments - IM/Clear and IM/110 (a 10% diffusion). The second enhancement is the incorporation of an enhanced light guide (ELG) providing for up to 30% increase in brightness. The TFT-LCD panel used for this module is a low-reflection and higher-color-saturation type. Therefore, this module is also suitable for multimedia use. Viewing angle is 6 o’clock direction. This module offers a wide viewing angle and high brightness (800cd/m2). Backlight-driving DC/AC inverter is not built in this module. WEDC assumes no responsibility for any damage resulting from the use of the device which does not comply with the instructions and the precautions specified in these specification sheets. WEDC does assume the responsibility for the warranty of the enhanced product. This module is composed of a color TFT-LCD panel, driver ICs, control circuit and power supply circuit and a backlight unit. Graphics and texts can be displayed on a 640 x RGB x 480 dot panel with 262,144 colors by supplying 18-bit data signal (6-bit/color), four timing signals, +5V DC supply voltage for TFT-LCD panel driving and supply voltage for backlight. MECHANICAL SPECIFICATIONS Parameter Specifications Unit Display Size 16 (6.4") Diagonal cm Active Area 130.6(H) x 97.0(V) mm Pixel Format 640(H) x 480(V) (1 pixel=R+G+B dots) pixel Pixel Pitch 0.204(H) x 0.202(V) mm Pixel Configuration RGB vertical stripe – Display Mode Normally white – Unit Outline Dimensions (1) 175.0(W) x 126.5(H) x 16.0(D) mm Mass 290 ± 20 g Surface Treatment IM/Clear (glossy) or IM/110 and hardcoat 3H – Note: 1. Excluding backlight cables. Original specifications created by Sharp. February, 2004 Rev. 0 1 White Electronic Designs - Display Systems Division • (503) 690-2460 • www.wedc.com White Electronic Designs Display Systems Division CN1 Used connector: Corresponding connector: INPUT TERMINALS TFT-LCD panel driving 1 31 2 30 CN1 pin arrangement from module surface (Transparent view) Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Symbol GND CK Hsync Vsync GND R0 R1 R2 R3 R4 R5 GND G0 G1 G2 G3 G4 G5 GND B0 B1 B2 B3 B4 B5 GND ENAB Vcc Vcc R/L U/D ENH064V1-800 DF9BA-31P-1V (Hirose Electric Co., Ltd.) DF9-31S-1V (Hirose Electric Co., Ltd.) DF9A-31S-1V (Hirose Electric Co., Ltd.) DF9B-31S-1V (Hirose Electric Co., Ltd.) DF9M-31S-1V (Hirose Electric Co., Ltd.) Function – Clock signal for sampling each data signal Horizontal synchronous signal Vertical synchronous signal – RED data signal (LSB) RED data signal RED data signal RED data signal RED data signal RED data signal (MSB) – GREEN data signal (LSB) GREEN data signal GREEN data signal GREEN data signal GREEN data signal GREEN data signal (MSB) – BLUE data signal (LSB) BLUE data signal BLUE data signal BLUE data signal BLUE data signal BLUE data signal (MSB) – Signal to settle the horizontal display position +5.0V power supply +5.0V power supply Horizontal display mode select signal Vertical display mode select signal Remark – – (1) (1) – – – – – – – – – – – – – – – – – – – – – – (2) – – (3) (4) The shielding case is not connected with GND. Notes: 1) 480 line, 400 line or 350 line mode is selected by the polarity combination of both synchronous signals. 2) The horizontal display start timing is settled in accordance with a rising timing of ENAB signal. In case ENAB is fixed “Low”, the horizontal start timing is determined as described in Horizontal Display Position, p. 6. Do not keep ENAB “High” during operation. Mode 480 lines 400 lines 350 lines Hsync negative negative positive Vsync negative positive negative Original specifications created by Sharp. February, 2004 Rev. 0 2 White Electronic Designs - Display Systems Division • (503) 690-2460 • www.wedc.com White Electronic Designs Display Systems Division ENH064V1-800 3) CDEW WEDC display reverse R/L=OPEN, U/D=OPEN R/L=LOW, U/D=OPEN 4) WEDC WEDC R/L=OPEN, U/D=OPEN display reverse R/L=OPEN, U/D=LOW Used connector: Corresponding connector: BHR-03VS-1(JST) SM02(8.0)B-BHS(JST) BACKLIGHT DRIVING CNA, CNB Pin No. 1 2 3 Symbol VHIGH NC VLOW Function Power supply for lamp (High voltage side) This is electrically opened Power supply for lamp (Low voltage side) ABSOLUTE MAXIMUM RATINGS Parameter Input Voltage +5V Supply Voltage Storage Temperature Operating Temperature (Ambient) Symbol VI VCC Tstg Topa Condition Ta=25°C Ta=25°C – – Ratings -0.3~ VCC + 0.3 0~+6 -25 ~ + 70 0 ~ + 55 Unit V V °C °C Remark (1) – (2) Notes: 1. CK, R0~R5, G0~G5, B0~B5, Hsync, Vsync, ENAB, R/L, U/D 2. Humidity : 95%RH Max. at Ta < 40°C. Maximum wet-bulb temperature at 39°C or less at Ta>40°C. No condensation. Original specifications created by Sharp. February, 2004 Rev. 0 3 White Electronic Designs - Display Systems Division • (503) 690-2460 • www.wedc.com White Electronic Designs Display Systems Division ENH064V1-800 ELECTRICAL CHARACTERISTICS TFT-LCD Panel Driving Parameter Supply Voltage +5V Current Dissipation Permissive Input Ripple Voltage Input Voltage (Low) Input Voltage (High) Input Current (Low) Input Current (High) Symbol VCC ICC VRF VIL VIH IOL1 IOL2 IOH1 IOH2 Min. +4.5 – – – 0.7VCC – – – – Typ. +5.0 250 – – – – – – – Max. +5.5 360 100 0.3VCC – 1.0 60.0 1.0 60.0 Unit V mA mVp-p V V μA μA μA μA Notes: 1) Vcc-turn-on conditions t1 ≤ 10ms 0 < t2 ≤ 10ms 0< t3 ≤ 1s Remark (1) (2) VCC=+5V (3) VI =0V (4) VI =0V (5) VI =VCC (6) VI =VCC (7) Vcc 4.5V 2.7V Vcc-dip conditions 1) 2.7V ≤ VCC < 4.5V td ≤ 10ms 4.5V data t1 t3 t2 2) VCC < 2.7V Vcc-dip conditions should also follow the Vcc-turn-on conditions 4.5V 2.7V Vcc td Notes: 2) Typical current situation : 3) 4) 5) 6) 7) 16-gray-bar pattern 480 line mode VCC = +50V CK, R0~R5, G0~G5, B0~B5, Hsync, Vsync, ENAB, R/L, U/D CK, R0~R5, G0~G5, B0~B5, Hsync, Vsync, ENAB R/L CK, R0~R5, G0~G5, B0~B5, Hsync, Vsync ENAB, U/D RGB RGB RGB G3O G34 G38 ... RGB RGB G350 G310 Original specifications created by Sharp. February, 2004 Rev. 0 4 White Electronic Designs - Display Systems Division • (503) 690-2460 • www.wedc.com White Electronic Designs Display Systems Division ENH064V1-800 TA=25°C BACKLIGHT DRIVING The backlight system is an edge-lighting type with four CCFTs (Cold Cathode Fluorescent Tube). The Characteristics of a single lamp are shown in the following table. Parameter Lamp Current Lamp Power Consumption Lamp Frequency Kick-off Voltage Symbol IL PL FL VS Lamp Life Time LL Min. 2.0 – 20 – – – Typ. 6.0 2.16 35 – – 25000 Max. 6.5 – 60 800 1000 – Unit mArms W KHz Vrms Vrms hour Remark (1) (2) (3) Ta=25°C Ta=0°C (4) (5) Notes: 1) Lamp current is measured with current meter for high frequency as shown below. 1 Module Inverter A 3 ~ 3 pin is VLOW 2) At the condition of YL=(300) cd/m2 3) Lamp frequency may produce interference with horizontal synchronous frequency, and this may cause horizontal beat on the display. Therefore, lamp frequency shall be detached as much as possible from the horizontal synchronous frequency and from the harmonics of horizontal synchronous to avoid interference. 4) The open output voltage of the inverter shall be maintained for more than 1 sec; otherwise the lamp may not be turned on. 5) Since lamp is consumable, the life time written above is referential value and is not guaranteed in this specification sheet by WEDC. Lamp life time is defined that it applied either (1) or (2) under this condition (Continuous turning on at Ta=25°C, IL=6mArms) 1) Brightness becomes 50% of the original value under standard condition. 2) Kickoff voltage at Ta=0°C exceeds maximum value, 1000 Vrms. If operating under lower temp environment, the lamp exhaustion is accelerated and the brightness becomes lower. (Continuous operating for around 1 month under lower temp condition may reduce the brightness to half of the original brightness.) In case of such usage under lower temp environment, periodic lamp exchange by WEDC is recommended. Note: 1) The performance of the backlight, for example life time or brightness, is influenced by the characteristics of the DC /AC inverter for the lamp. When designing or ordering the inverter, make certain that poor lighting caused by the mismatch of the backlight and the inverter (mis-lighting, flicker, etc.) do not occur. Once this is confirmed, the module should be operated in the same condition as it is installed in the instrument. Original specifications created by Sharp. February, 2004 Rev. 0 5 White Electronic Designs - Display Systems Division • (503) 690-2460 • www.wedc.com White Electronic Designs Display Systems Division ENH064V1-800 TIMING CHARACTERISTICS OF INPUT SIGNALS Timing diagrams of input signal are shown in Fig. 2-1~3. TIMING CHARACTERISTICS Parameter Symbol Clock Data Horizontal sync. Signal Mode Min. Typ. Max. Unit Frequency 1/Tc all – 25.18 28.33 MHz High Time Tch ↑ 5 – – ns Low Time Tcl ↑ 10 – – ns Setup Time Tds ↑ 5 – – ns Hold Time Tdh ↑ 10 – – ns ↑ 30.00 31.78 – μs ↑ 770 800 900 clock Cycle TH Pulse Width THp ↑ 2 96 200 clock 480 515 525 560 line 400 446 449 480 line 350 447 449 510 line TVp all 2 – 34 line Horizontal Display Period THd ↑ 640 640 640 clock Hsync-Clock Phase Difference THc ↑ 10 – TC-10 ns Hsync-Vsync Phase Difference TVh ↑ 0 – TH-THp clock Cycle Vertical sync. Signal Pulse Width TV Note: 1) In case of lower frequency, the deterioration of display quality, flicker, etc., may occur. HORIZONTAL DISPLAY POSITION The horizontal display position is determined by ENAB signal and the input data corresponding to the rising edge of ENAB signal is displayed at the left end of the active area. Parameter Enable Signal Symbol Min. Typ. Max. Setup time Tes 5 – Tc-10 ns Pulse width Tep 2 640 640 clock THe 44 – TH-664 clock Hsync-Enable Signal Phase Difference Unit Note: 1) When ENAB is fixed “Low”, the display starts from the data of C104 (clock) as shown in Fig. 2-1~3. Be careful the module does not work when ENAB is fixed “High”. Original specifications created by Sharp. February, 2004 Rev. 0 6 White Electronic Designs - Display Systems Division • (503) 690-2460 • www.wedc.com White Electronic Designs Display Systems Division VERTICAL DISPLAY POSITION on the screen like the following figure when the period of vertical synchronous signal, TV, is typical value. The vertical display position is automatically centered in the active area at each mode of VGA, 480-, 400-, and 350-line mode. Each mode is selected depending on the polarity of the synchronous signals described in Note 1 on page 2. In 400-, and 350-line mode, the data in the vertical data invalid period is also displayed. So inputting all data “()” is recommended during vertical data invalid period. ENAB signal has no relation to the vertical display position. In each mode, the data of TVn is displayed on the top line of the active area. The display position will be centered Mode ENH064V1-800 V-data Start (TVs) V-data Period (TVd) V-display Start (TVn) V-display Period 480 400 350 34 34 61 480 400 350 data invalid period 34 443-TV 445-TV 4 0 lines data period 480 480 480 line line line 6 5 lines data invalid period data period 4 0 0 lines data invalid period Unit 3 5 0 lines 6 5 lines data invalid period 4 0 lines 350 lines mode (TV=449) 400 lines mode (TV=449) INPUT DATA SIGNALS AND DISPLAY POSITION ON THE SCREEN Display postion of input data (480 lines mode) UP D1, DH1 D2, DH1 D1, DH2 D2, DH2 D3, DH1 D640, DH1 D1, DH3 R G B R/L = OPEN U/D = OPEN D640, DH480 D1, DH480 Original specifications created by Sharp. February, 2004 Rev. 0 7 White Electronic Designs - Display Systems Division • (503) 690-2460 • www.wedc.com White Electronic Designs Display Systems Division ENH064V1-800 TH THp Horizontal sync. signal (Hsync) 0.3Vcc 0.3Vcc 0.7Vcc 0.3Vcc THc 0.7Vcc Clock signal (CK) 0.3Vcc C1* 0.3Vcc Data signal (R0~R5, G0~G5 B0~B5) Tc Tch Tc *Only when enable terminal is fixed "low" 0.3Vcc 0.3Vcc C104* C2* Number of clock Horizontal invalid data period D1 D2 Tds 0.3Vcc Tdh Number of H-data 0.7Vcc D3 THe Horizontal invalid data period D640 D639 0.3Vcc THd 0.7Vcc Data enable signal (ENAB) Tes 0.3Vcc Tep TV Vertical sync. signal (Vsync) TVp 0.7Vcc 0.3Vcc 0.3Vcc TVh Horizontal sync. signal (Hsync) Data signal (R0~R5, G0~G5 B0~B5) 0.7Vcc 1 34 2 TVs Number of line Vertical invalid data period DH1 TVd DH2 DH3 DH479 DH480 Vertical invalid data period Number of V-data line Fig 2-1 Input signal waveforms (480 line mode) Original specifications created by Sharp. February, 2004 Rev. 0 8 White Electronic Designs - Display Systems Division • (503) 690-2460 • www.wedc.com White Electronic Designs Display Systems Division ENH064V1-800 TH THp Horizontal sync. signal (Hsync) 0.3Vcc 0.3Vcc 0.7Vcc 0.3Vcc Tc Tch Tc THc *Only when enable terminal (ENAB) is fixed "Low" 0.7Vcc Clock signal (CK) 0.3Vcc 0.3Vcc 0.3Vcc 0.3Vcc C1* C2* C104* Tds Tdh Number of clock Data signal (R0~R5, G0~G5, B0~B5) Horizontal invalid data period D1 D2 Number of H-data 0.7Vcc D3 D639 D640 Horizontal invalid data period 0.3Vcc THe THd 0.7Vcc Data enable signal (ENAB) Tes 0.3Vcc Tep TV Vertical sync. signal (Vsync) 0.7Vcc 0.7Vcc TVp 0.3Vcc TVh Horizontal sync. signal (Hsync) 0.7Vcc 1 2 34 TVs Data signal (R0~R5, G0~G5, B0~B5) Number of line TVd DH1 Vertical invalid data period DH2 DH3 DH399 DH400 Vertical invalid data period Number of V-data line Fig. 2-2 Input signal waveforms (400 line mode) Original specifications created by Sharp. February, 2004 Rev. 0 9 White Electronic Designs - Display Systems Division • (503) 690-2460 • www.wedc.com White Electronic Designs Display Systems Division ENH064V1-800 TH Horizontal sync. signal 0.7Vcc (Hsync) 0.7Vcc 0.7Vcc 0.3Vcc THp Tc Tch Tc THc *Only when enable terminal (ENAB) fixed "low" Clock signal (CK) 0.7Vcc 0.3Vcc 0.3Vcc 0.3Vcc 0.3Vcc C1* C2* C104* Tds Number of clock Data signal (R0~R5, G0~G5, B0~B5) Horizontal invalid data period D1 D2 Tdh Number of H-data 0.7Vcc D3 D639 D640 Horizontal invalid data period 0.3Vcc THe THd Data enable signal (ENAB) 0.7Vcc Tes 0.3Vcc Tep TV Vertical sync. signal (Vsync) TVp 0.7Vcc 0.3Vcc 0.3Vcc TVh Horizontal sync. signal (Hsync) 0.3Vcc 2 1 Data signal (R0~R5, G0~G5, B0~B5) TVs Vertical invalid data period 61 Number of line DH1 TVd DH2 Fig 2-3 Input signal waveforms (350 line mode) DH3 DH349 DH350 Vertical invalid data period Number of V-data line Original specifications created by Sharp. February, 2004 Rev. 0 10 White Electronic Designs - Display Systems Division • (503) 690-2460 • www.wedc.com White Electronic Designs Display Systems Division ENH064V1-800 INPUT SIGNALS, BASIC DISPLAY COLOR AND GRAY SCALE OF EACH COLOR Gray Scale or Red Basic Color Colors & Gray scale Black Blue Green Cyan Red Magenta Yellow White Black ↑ Darker ↑ ↓ Brighter ↓ Gray Scale of Green Red Black ↑ Darker ↑ ↓ Brighter ↓ Gray Scale of Blue Green Black ↑ Darker ↑ ↓ Brighter ↓ Blue Data Signal Gray R0 R1 R2 R3 R4 R5 G0 G1 G2 G3 G4 G5 B0 B1 B2 B3 B4 B5 Scale – 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 – 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 – 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 – 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 – 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 – 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1 – 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 – 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 GS0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 GS1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 GS2 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ GS61 0 0 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 GS62 0 0 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 GS63 0 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 GS0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 GS1 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 GS2 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ GS61 0 0 0 0 0 0 1 0 1 1 1 1 0 0 0 0 0 0 GS6 0 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 GS63 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 GS0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 GS1 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 GS2 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 ↓ ↓ ↓ ↓ ↓ ↓ ↓ ↓ GS61 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 1 1 1 GS62 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 GS63 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 Notes: 1) 0: Low level voltage 1: High level voltage 2) Each basic color can be displayed in 64 gray scales from 6 bit data signals. According to the combination of total 18 bit data signals, the 262,144-color display can be achieved on the screen. Original specifications created by Sharp. February, 2004 Rev. 0 11 White Electronic Designs - Display Systems Division • (503) 690-2460 • www.wedc.com White Electronic Designs Display Systems Division ENH064V1-800 OPTICAL CHARACTERISTICS Ta=25°C, VCC=+5V Parameter Horizontal Viewing Angle Range Vertical Contrast Ratio Symbol θ 21 θ 22 θ 11 θ 12 Condition (CR≥5) Best Viewing Angle CR Rise Decay Response Time Chromaticity of White Luminance of White White Uniformity Viewing Angle Range as a Brightness Definition Horizontal Vertical tr td X Y YL δw θ 21 θ 22 θ 11 θ 12 θ = 0° 50% of the maximum brightness Min. 60 60 35 55 100 Typ. 70 70 40 70 – Max. – – – – – Unit Deg. Deg. Deg. Deg. – – – – – 700 – – – – – 20 40 0.313 0.325 800 – 45 45 45 45 – – – – – 1.45 – – – – ms ms – – cd/m2 – Deg. Deg. Deg. Deg. Remark (4) (2,4) (3,4) (4) (5) (1) Note: 1) The measurement shall be executed 30 minutes after lighting at rating. (typical condition: IL=6mArms) The optical characteristics shall be measured in a dark room or equivalent state with the method shown in Fig. 3 below. Photodetector (BM-5A: TOPCON) Field=2° 400mm TFT-LCD Module LCD Panel Center of the screen Fig. 3 Optical Characteristics Measurement Method Original specifications created by Sharp. February, 2004 Rev. 0 12 White Electronic Designs - Display Systems Division • (503) 690-2460 • www.wedc.com White Electronic Designs Display Systems Division ENH064V1-800 Normal line Notes: 1) Definitions of viewing angle range: θ22 θ12 θ11 θ21 6 o'clock direction black Contrast Ratio (CR) = Luminance (brightness) with all pixels white Luminance (brightness) with all pixels black 3) Definition of response time: The response time is defined as the following figure and shall be measured by switching the input signal for “black” and “white”. Photodetector output (Relative Value) white 2) Definition of contrast ratio: The contract ratio is defined as the following. white 100% 90% 10% 0% τd τr time 160 320 480 pixel 4) This shall be measured at center of the screen. 5) Definition of white uniformity: White uniformity is defined as the following with five measurements. A D 120 (A~E). C Luminance of five points (brightness) δw= Maximum Minimum Luminance of five points (brightness) B 240 E 360 pixel Original specifications created by Sharp. February, 2004 Rev. 0 13 White Electronic Designs - Display Systems Division • (503) 690-2460 • www.wedc.com White Electronic Designs Display Systems Division DISPLAY QUALITY 10) Laminated film is attached to the module surface to prevent it from being scratched. Before use, peel the film off slowly, with strict attention to electrostatic charges. Ionized air shall be blown over during the action. Blow off ‘dust’ on the polarizer by using an ionized nitrogen gun. The display quality of the color TFT-LCD module shall be in compliance with the Incoming Inspection Standard. HANDLING PRECAUTIONS 1) Be sure to turn off the power supply when inserting or disconnecting the cable. 2) Design the cabinet so that the module can be installed without any extra stress such as warp or twist. 3) Since the front polarizer is easily damaged, pay attention to avoid rubbing with something hard or sharp. 4) Wipe water off immediately. Long contact with water may cause discoloration or spots. 5) When the panel surface is soiled, use an absorbent cotton or other soft cloth to wipe it off. 6) Since the panel is made of glass, refined wires and components, it may break, crack or cause internal wire breaking if dropped or bumped on hard surface. Handle with care. ENH064V1-800 11) Connect GND to 4 place of mounting holes to stabilize against EMI and external noise. 12) The high voltage portions on the backlight are very dangerous. Careless handling may lead to electrical shock. PACKING FORM 1) Piling number of cartons: MAX 10 2) Package quantity in one carton: 20pcs 3) Carton size: 355 (W) X 282 (D) X 265 (H) mm 4) Total mass of 1 carton filled with full modules: 7.0kg OTHERS 1) Disassembling the module can cause permanent damage and should be avoided. Image retention may occur when a fixed pattern is displayed for a long time. 7) Since CMOS LSI is used in this module, make certain one is grounded when handling. 2) 8) Observe all other precautionary requirements in handling components. EXCHANGE OF LAMPS 9) This module has its circuitry PCBs on the rear side and should be carefully handled in order to avoid being stressed. This must be action must be performed by WEDC. RELIABILITY TEST ITEMS No. Test item Conditions 1 High Temperature Storage Test Ta=70°C 240h 2 Ta=25°C Ta=40°C, 95%RH (No Condensation) Ta=55°C Ta=0°C Frequency 240h 4 5 Low Temperature Storage Test High Temperature & High Humidity Operation Test High Temperature Operation Test Low Temperature Operation Test 6 Vibration Test (Non-Operating) 7 Shock Test (Non-Operating) 3 Sweep time Test period Max. gravity Pulse width Direction 240h 240h 240h :10~57Hz/Vibration width (one side):0.075mm :58~500Hz/Gravity: 9.8m/s2 :11 minutes :3 hours (1 hour for each direction of X,Y,Z) :490m/s2 :11ms, half sine wave :±X, ±Y, ±Z (once for each direction.) Original specifications created by Sharp. February, 2004 Rev. 0 14 White Electronic Designs - Display Systems Division • (503) 690-2460 • www.wedc.com White Electronic Designs Display Systems Division ENH064V1-800 0.638 2.157 [54.79 mm] 5.362 [136.20 mm] Bezel Opening 4.980 4.892 4.459 4.399 Active Area Bezel Opening 3.819 [97.00 mm] 3.937 [100.00 mm] 0.581 0.521 0.089 0.000 4X ø0.083 Mounting Holes 6.358 6.417 6.801 6.890 1.055 1.217 0.000 0.089 5.142 Active Area [130.60 mm] 1) TOLERANCE X-DIRECTION A:4×12±0×8 2) TOLERANCE X-DIRECTION B:1×52±0×8 3) TOLERANCE Y-DIRECTION C:1×52±0×8 4) TOLERANCE Y-DIRECTION 5) OBLIQUITY OF DISPLAY AREA Notes: 1) Unspecified tolerance to be ±0.5. 2) Floating of PWB and chassis are excluded from module thickness. 3) Diameter of mounting boss shall be the range of 3.5mm to 4mm. (center of oval hole) D:1×52±0×8 IE-FI<0×8 Original specifications created by Sharp. February, 2004 Rev. 0 15 White Electronic Designs - Display Systems Division • (503) 690-2460 • www.wedc.com