AD EVAL-ADUC812QS

a
MicroConverter ®, Multichannel
12-Bit ADC with Embedded Flash MCU
ADuC812
FEATURES
Analog I/O
8-Channel, High Accuracy 12-Bit ADC
On-Chip, 100 ppm/C Voltage Reference
High Speed 200 kSPS
DMA Controller for High Speed ADC-to-RAM Capture
2 12-Bit Voltage Output DACs
On-Chip Temperature Sensor Function
Memory
8K Bytes On-Chip Flash/EE Program Memory
640 Bytes On-Chip Flash/EE Data Memory
256 Bytes On-Chip Data RAM
16M Bytes External Data Address Space
64K Bytes External Program Address Space
8051 Compatible Core
12 MHz Nominal Operation (16 MHz Max)
3 16-Bit Timer/Counters
High Current Drive Capability—Port 3
9 Interrupt Sources, 2 Priority Levels
Power
Specified for 3 V and 5 V Operation
Normal, Idle, and Power-Down Modes
On-Chip Peripherals
UART and SPI® Serial I/O
2-Wire (400 kHz I2C® Compatible) Serial I/O
Watchdog Timer
Power Supply Monitor
APPLICATIONS
Intelligent Sensors Calibration and Conditioning
Battery-Powered Systems (Portable PCs, Instruments,
Monitors)
Transient Capture Systems
DAS and Communications Systems
Control Loop Monitors (Optical Networks/Base Stations)
GENERAL DESCRIPTION
The ADuC812 is a fully integrated 12-bit data acquisition system
incorporating a high performance self-calibrating multichannel
ADC, dual DAC, and programmable 8-bit MCU (8051 instruction set compatible) on a single chip.
The programmable 8051 compatible core is supported by 8K
bytes Flash/EE program memory, 640 bytes Flash/EE data
memory, and 256 bytes data SRAM on-chip.
Additional MCU support functions include Watchdog Timer,
Power Supply Monitor, and ADC DMA functions. Thirty-two
programmable I/O lines, I2C compatible SPI and Standard
UART Serial Port I/O are provided for multiprocessor interfaces
and I/O expansion.
Normal, idle, and power-down operating modes for both the
MCU core and analog converters allow flexible power management schemes suited to low power applications. The part is
specified for 3 V and 5 V operation over the industrial temperature range and is available in a 52-lead, plastic quad
flatpack package, and in a 56-lead, chip scale package.
FUNCTIONAL BLOCK DIAGRAM
P0.0–P0.7
AIN0 (P1.0)–AIN7 (P1.7)
AIN
MUX
P1.0–P1.7
ADC
CONTROL
AND
CALIBRATION
LOGIC
12-BIT
SUCCESSIVE
APPROXIMATION
ADC
T/H
P3.0–P3.7
P2.0–P2.7
DAC0
BUF
DAC0
DAC1
BUF
DAC1
DAC
CONTROL
T0 (P3.4)
MICROCONTROLLER
2.5V
REF
VREF
TEMP
SENSOR
BUF
8051 BASED
MICROCONTROLLER CORE
POWER SUPPLY
MONITOR
8K 8 PROGRAM
FLASH EEPROM
WATCHDOG
TIMER
640 8 USER
FLASH EEPROM
UART
256 8 USER
RAM
ADuC812
CREF
3 16-BIT
TIMER/COUNTERS
2-WIRE
SERIAL I/O
SPI
MUX
T1 (P3.5)
T2 (P1.0)
T2EX (P1.1)
INT0 (P3.2)
INT1 (P3.3)
ALE
PSEN
OSC
EA
RESET
AVDD
AGND
DVDD
DGND
XTAL1 XTAL2 RxD TxD SCLOCK MOSI/ MISO
(P3.0) (P3.1)
SDATA (P3.3)
REV. E
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties that
may result from its use. No license is granted by implication or otherwise
under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective companies.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
www.analog.com
Fax: 781/326-8703
© 2003 Analog Devices, Inc. All rights reserved.
ADuC812
TABLE OF CONTENTS
FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
APPLICATONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . . . . 6
PIN CONFIGURATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
PIN FUNCTION DESCRIPTIONS . . . . . . . . . . . . . . . . . . . . . 7
TERMINOLOGY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
ADC SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Integral Nonlinearity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Differential Nonlinearity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Offset Error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Full-Scale Error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Signal to (Noise + Distortion) Ratio . . . . . . . . . . . . . . . . . . . . 8
Total Harmonic Distortion . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
DAC SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Relative Accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Voltage Output Settling Time . . . . . . . . . . . . . . . . . . . . . . . . . 8
Digital-to-Analog Glitch Impulse . . . . . . . . . . . . . . . . . . . . . . . 8
ARCHITECTURE, MAIN FEATURES . . . . . . . . . . . . . . . . . . 9
MEMORY ORGANIZATION . . . . . . . . . . . . . . . . . . . . . . . . . . 9
OVERVIEW OF MCU-RELATED SFRs . . . . . . . . . . . . . . . . . 10
Accumulator SFR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
B SFR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Stack Pointer SFR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Data Pointer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Program Status Word SFR . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Power Control SFR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
SPECIAL FUNCTION REGISTERS . . . . . . . . . . . . . . . . . . . 11
ADC CIRCUIT INFORMATION . . . . . . . . . . . . . . . . . . . . . . 12
General Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
ADC Transfer Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Typical Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
ADCCON1—(ADC Control SFR #1) . . . . . . . . . . . . . . . . . 13
ADCCON2—(ADC Control SFR #2) . . . . . . . . . . . . . . . . . 14
ADCCON3—(ADC Control SFR #3) . . . . . . . . . . . . . . . . . 14
Driving the ADC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Voltage Reference Connections . . . . . . . . . . . . . . . . . . . . . . . 16
Configuring the ADC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
ADC DMA Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
DMA Mode Configuration Example . . . . . . . . . . . . . . . . . . . 17
Micro Operation during ADC DMA Mode . . . . . . . . . . . . . . 17
Offset and Gain Calibration Coefficients . . . . . . . . . . . . . . . . 17
Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
NONVOLATILE FLASH MEMORY . . . . . . . . . . . . . . . . . . . 18
Flash Memory Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Flash/EE Memory and the ADuC812 . . . . . . . . . . . . . . . . . . 18
ADuC812 Flash/EE Memory Reliability . . . . . . . . . . . . . . . . 18
Using the Flash/EE Program Memory . . . . . . . . . . . . . . . . . . 19
Using the Flash/EE Data Memory . . . . . . . . . . . . . . . . . . . . . 19
ECON—Flash/EE Memory Control SFR . . . . . . . . . . . . . . . 20
Flash/EE Memory Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Using the Flash/EE Memory Interface . . . . . . . . . . . . . . . . . . 20
Erase-All . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Program a Byte . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
USER INTERFACE TO OTHER ON-CHIP
ADuC812 PERIPHERALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Using the DAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
WATCHDOG TIMER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
POWER SUPPLY MONITOR . . . . . . . . . . . . . . . . . . . . . . . . .
SERIAL PERIPHERAL INTERFACE . . . . . . . . . . . . . . . . . . .
MISO (Master In, Slave Out Data I/O Pin) . . . . . . . . . . . . . .
MOSI (Master Out, Slave In Pin) . . . . . . . . . . . . . . . . . . . . .
SCLOCK (Serial Clock I/O Pin) . . . . . . . . . . . . . . . . . . . . . .
SS (Slave Select Input Pin) . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the SPI Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPI Interface—Master Mode . . . . . . . . . . . . . . . . . . . . . . . . .
SPI Interface—Slave Mode . . . . . . . . . . . . . . . . . . . . . . . . . .
I2C COMPATIBLE INTERFACE . . . . . . . . . . . . . . . . . . . . . .
8051 COMPATIBLE ON-CHIP PERIPHERALS . . . . . . . . . .
Parallel I/O Ports 0–3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Timers/Counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Timer/Counters 0 and 1 Data Registers . . . . . . . . . . . . . . . . .
TH0 and TL0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TH1 and TL1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TIMER/COUNTERS 0 AND 1 OPERATING MODES . . . . .
Mode 0 (13-Bit Timer/Counter) . . . . . . . . . . . . . . . . . . . . . .
Mode 1 (16-Bit Timer/Counter) . . . . . . . . . . . . . . . . . . . . . .
Mode 2 (8-Bit Timer/Counter with Auto Reload) . . . . . . . . .
Mode 3 (Two 8-Bit Timer/Counters) . . . . . . . . . . . . . . . . . .
Timer/Counter 2 Data Registers . . . . . . . . . . . . . . . . . . . . . .
TH2 and TL2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RCAP2H and RCAP2L . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Timer/Counter Operation Modes . . . . . . . . . . . . . . . . . . . . .
16-Bit Autoreload Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16-Bit Capture Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UART SERIAL INTERFACE . . . . . . . . . . . . . . . . . . . . . . . . .
Mode 0 (8-Bit Shift Register Mode) . . . . . . . . . . . . . . . . . . .
Mode 1 (8-Bit UART, Variable Baud Rate) . . . . . . . . . . . . . .
Mode 2 (9-Bit UART with Fixed Baud Rate) . . . . . . . . . . . .
Mode 3 (9-Bit UART with Variable Baud Rate) . . . . . . . . . .
UART Serial Port Baud Rate Generation . . . . . . . . . . . . . . .
Timer 1 Generated Baud Rates . . . . . . . . . . . . . . . . . . . . . . .
Timer 2 Generated Baud Rates . . . . . . . . . . . . . . . . . . . . . . .
INTERRUPT SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interrupt Priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interrupt Vectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ADuC812 HARDWARE DESIGN CONSIDERATIONS . . . .
Clock Oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
External Memory Interface . . . . . . . . . . . . . . . . . . . . . . . . . .
Power-On Reset Operation . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Grounding and Board Layout Recommendations . . . . . . . . .
OTHER HARDWARE CONSIDERATIONS . . . . . . . . . . . . .
In-Circuit Serial Download Access . . . . . . . . . . . . . . . . . . . .
Embedded Serial Port Debugger . . . . . . . . . . . . . . . . . . . . . .
Single-Pin Emulation Mode . . . . . . . . . . . . . . . . . . . . . . . . . .
Enhanced-Hooks Emulation Mode . . . . . . . . . . . . . . . . . . . .
Typical System Configuration . . . . . . . . . . . . . . . . . . . . . . . .
QUICKSTART DEVELOPMENT SYSTEM . . . . . . . . . . . . .
Download—In-Circuit Serial Downloader . . . . . . . . . . . . . . .
DeBug—In-Circuit Debugger . . . . . . . . . . . . . . . . . . . . . . . .
ADSIM—Windows Simulator . . . . . . . . . . . . . . . . . . . . . . . .
TIMING SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . .
OUTLINE DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
–2–
24
24
25
25
26
26
26
27
27
27
28
29
29
29
31
31
31
32
32
32
32
32
33
33
33
34
34
34
35
36
36
36
36
36
37
37
38
39
39
40
40
40
41
41
42
43
44
44
44
45
45
45
45
45
45
45
46
56
57
REV. E
1, 2 (AV
ADuC812
= DV = 3.0 V or 5.0 V 10%, REF /REF = 2.5 V Internal Reference, MCLKIN = 11.0592 MHz,
SPECIFICATIONS
f
= 200 kHz, DAC V Load to AGND; R = 2 k, C = 100 pF. All specifications T = T to T , unless otherwise noted.)
DD
SAMPLE
OUT
L
Parameter
ADC CHANNEL SPECIFICATIONS
DC ACCURACY3, 4
Resolution
Integral Nonlinearity
Differential Nonlinearity
CALIBRATED ENDPOINT ERRORS5, 6
Offset Error
Offset Error Match
Gain Error
Gain Error Match
USER SYSTEM CALIBRATION7
Offset Calibration Range
Gain Calibration Range
DD
IN
L
A
OUT
MIN
MAX
ADuC812BS
VDD = 5 V
VDD = 3 V
Unit
12
±1/2
±1.5
±1.5
±1
12
±1/2
±1.5
±1.5
±1
Bits
LSB typ
LSB max
LSB typ
LSB typ
±5
±1
1
±6
±1
1.5
±5
±1
1
±6
±1
1.5
LSB max
LSB typ
LSB typ
LSB max
LSB typ
LSB typ
±5
±2.5
±5
±2.5
% of VREF typ
% of VREF typ
ANALOG INPUT
Input Voltage Ranges
Leakage Current
Input Capacitance9
TEMPERATURE SENSOR10
Voltage Output at 25°C
Voltage TC
DAC CHANNEL SPECIFICATIONS
DC ACCURACY11
Resolution
Relative Accuracy
Differential Nonlinearity
Offset Error
Full-Scale Error
Full-Scale Mismatch
ANALOG OUTPUTS
Voltage Range_0
Voltage Range_1
Resistive Load
Capacitive Load
Output Impedance
ISINK
REV. E
fSAMPLE = 100 kHz
fSAMPLE = 100 kHz
fSAMPLE = 200 kHz
fSAMPLE = 100 kHz. Guaranteed No
Missing Codes at 5 V
fIN = 10 kHz Sine Wave
fSAMPLE = 100 kHz
DYNAMIC PERFORMANCE
Signal-to-Noise Ratio (SNR)8
Total Harmonic Distortion (THD)
Peak Harmonic or Spurious Noise
Test Conditions/Comments
70
–78
–78
70
–78
–78
dB typ
dB typ
dB typ
0 to VREF
±1
±0.1
20
0 to VREF
±1
±0.1
20
V
µA max
µA typ
pF max
600
–3.0
600
–3.0
mV typ
mV/°C typ
12
±3
±0.5
±60
±15
±30
±10
±0.5
12
±3
±1
±60
±15
±30
±10
±0.5
Bits
LSB typ
LSB typ
mV max
mV typ
mV max
mV typ
% typ
0 to VREF
0 to VDD
10
100
0.5
50
0 to VREF
0 to VDD
10
100
0.5
50
V typ
V typ
kΩ typ
pF typ
Ω typ
µA typ
–3–
Can vary significantly (> ±20%)
from device to device
Guaranteed 12-Bit Monotonic
% of Full-Scale on DAC1
ADuC812
SPECIFICATIONS1, 2 (continued)
Parameter
ADuC812BS
VDD = 5 V
VDD = 3 V
Unit
Test Conditions/Comments
DAC AC CHARACTERISTICS
Voltage Output Settling Time
15
15
µs typ
10
10
nV sec typ
Full-Scale Settling Time to
within 1/2 LSB of Final Value
1 LSB Change at Major Carry
2.3/VDD
150
2.5 ± 2.5%
2.5
100
2.3/VDD
150
2.5 ± 2.5%
2.5
100
V min/max
kΩ typ
V min/max
V typ
ppm/°C typ
10,000
50,000
10
50,000
Cycles min
Cycles typ
Years min
WATCHDOG TIMER
CHARACTERISTICS
Oscillator Frequency
64
64
kHz typ
POWER SUPPLY MONITOR
CHARACTERISTICS
Power Supply Trip Point Accuracy
±2.5
±2.5
±1.0
±1.0
% of Selected
Nominal Trip
Point Voltage
max
% of Selected
Nominal Trip
Point Voltage
typ
2.4
4
0.8
±10
±1
2.4
Digital-to-Analog Glitch Energy
REFERENCE INPUT/OUTPUT
REFIN Input Voltage Range9
Input Impedance
REFOUT Output Voltage
REFOUT Tempco
FLASH/EE MEMORY PERFORMANCE
CHARACTERISTICS12, 13
Endurance
Data Retention
DIGITAL INPUTS
Input High Voltage (VINH)
XTAL1 Input High Voltage (VINH) Only
Input Low Voltage (VINL)
Input Leakage Current (Port 0, EA)
Logic 1 Input Current
(All Digital Inputs)
±10
±1
Logic 0 Input Current (Port 1, 2, 3)
–80
–40
Logic 1-0 Transition Current (Port 1, 2, 3) –700
–400
Input Capacitance
10
0.8
±10
±1
V min
V min
V max
µA max
µA typ
±10
±1
–40
–20
–500
–200
10
µA max
µA typ
µA max
µA typ
µA max
µA typ
pF typ
–4–
Initial Tolerance @ 25°C
VIN = 0 V or VDD
VIN = 0 V or VDD
VIN = VDD
VIN = VDD
VIL = 450 mV
VIL = 2 V
VIL = 2 V
REV. E
ADuC812
Parameter
ADuC812BS
VDD = 5 V
VDD = 3 V
Unit
Test Conditions/Comments
DIGITAL OUTPUTS
Output High Voltage (VOH)
2.4
2.4
V min
4.0
2.6
V typ
VDD = 4.5 V to 5.5 V
ISOURCE = 80 µA
VDD = 2.7 V to 3.3 V
ISOURCE = 20 µA
0.4
0.2
0.4
0.2
±10
±1
10
0.4
0.2
0.4
0.2
±10
±1
10
V max
V typ
V max
V typ
µA max
µA typ
pF typ
ISINK = 1.6 mA
ISINK = 1.6 mA
ISINK = 8 mA
ISINK = 8 mA
43
32
26
8
25
18
15
7
30
5
25
16
12
3
10
6
6
2
15
5
mA max
mA typ
mA typ
mA typ
mA max
mA typ
mA typ
mA typ
µA max
µA typ
MCLKIN = 16 MHz
MCLKIN = 16 MHz
MCLKIN = 12 MHz
MCLKIN = 1 MHz
MCLKIN = 16 MHz
MCLKIN = 16 MHz
MCLKIN = 12 MHz
MCLKIN = 1 MHz
Output Low Voltage (VOL)
ALE, PSEN, Ports 0 and 2
Port 3
Floating State Leakage Current
Floating State Output Capacitance
POWER REQUIREMENTS14, 15, 16
IDD Normal Mode17
IDD Idle Mode
IDD Power-Down Mode18
NOTES
1
Specifications apply after calibration.
2
Temperature range –40°C to +85°C.
3
Linearity is guaranteed during normal MicroConverter core operation.
4
Linearity may degrade when programming or erasing the 640 byte Flash/EE space during ADC conversion times due to on-chip charge pump activity.
5
Measured in production at V DD = 5 V after Software Calibration Routine at 25°C only.
6
User may need to execute Software Calibration Routine to achieve these specifications, which are configuration dependent.
7
The offset and gain calibration spans are defined as the voltage range of user system offset and gain errors that the ADuC812 can compensate.
8
SNR calculation includes distortion and noise components.
9
Specification is not production tested, but is supported by characterization data at initial product release.
10
The temperature sensor will give a measure of the die temperature directly; air temperature can be inferred from this result.
11
DAC linearity is calculated using:
Reduced code range of 48 to 4095, 0 to V REF range
Reduced code range of 48 to 3995, 0 to V DD range
DAC output load = 10 kΩ and 50 pF.
12
Flash/EE Memory Performance Specifications are qualified as per JEDEC Specification (Data Retention) and JEDEC Draft Specification A117 (Endurance).
13
Endurance Cycling is evaluated under the following conditions:
Mode
= Byte Programming, Page Erase Cycling
Cycle Pattern
= 00H to FFH
Erase Time
= 20 ms
Program Time
= 100 µs
14
IDD at other MCLKIN frequencies is typically given by:
Normal Mode (V DD = 5 V):
IDD = (1.6 nAs × MCLKIN) + 6 mA
Normal Mode (V DD = 3 V):
IDD = (0.8 nAs × MCLKIN) + 3 mA
Idle Mode (V DD = 5 V):
IDD = (0.75 nAs × MCLKIN) + 6 mA
Idle Mode (V DD = 3 V):
IDD = (0.25 nAs × MCLKIN) + 3 mA
where MCLKIN is the oscillator frequency in MHz and resultant I DD values are in mA.
15
IDD currents are expressed as a summation of analog and digital power supply currents during normal MicroConverter operation.
16
IDD is not measured during Flash/EE program or erase cycles; I DD will typically increase by 10 mA during these cycles.
17
Analog IDD = 2 mA (typ) in normal operation (internal V REF, ADC, and DAC peripherals powered on).
18
EA = Port0 = DV DD, XTAL1 (Input) tied to DV DD, during this measurement.
Typical specifications are not production tested, but are supported by characterization data at initial product release.
Timing Specifications—See Pages 46–55.
Specifications subject to change without notice.
Please refer to User Guide, Quick Reference Guide, Application Notes, and Silicon Errata Sheet at www.analog.com/microconverter for additional information.
REV. E
–5–
ADuC812
Storage Temperature Range . . . . . . . . . . . . –65°C to +150°C
Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . 150°C
θJA Thermal Impedance . . . . . . . . . . . . . . . . . . . . . . . 90°C/W
Lead Temperature, Soldering
Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . . . 215°C
Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . . 220°C
ABSOLUTE MAXIMUM RATINGS*
(TA = 25°C, unless otherwise noted.)
AVDD to DVDD . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +0.3 V
AGND to DGND . . . . . . . . . . . . . . . . . . . . –0.3 V to +0.3 V
DVDD to DGND, AVDD to AGND . . . . . . . . . –0.3 V to +7 V
Digital Input Voltage to DGND . . . –0.3 V to DVDD + 0.3 V
Digital Output Voltage to DGND . . –0.3 V to DVDD + 0.3 V
VREF to AGND . . . . . . . . . . . . . . . . . –0.3 V to AVDD + 0.3 V
Analog Inputs to AGND . . . . . . . . . . –0.3 V to AVDD + 0.3 V
Operating Temperature Range Industrial (B Version)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –40°C to +85°C
*Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those listed in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
PIN CONFIGURATIONS
1
P1.2/ADC2
2
37
P2.5/A13/A21
P1.3/ADC3
36
P2.4/A12/A20
P0.1/AD1
P0.0/AD0
ALE
PSEN
EA
46
45
44
43
37
DGND
XTAL2
AGND
7
36
DVDD
AGND
8
TOP VIEW
(Not to Scale)
35
XTAL2
CREF
VREF
9
34
XTAL1
10
33
P2.3/A11/A19
DAC0
11
32
P2.2/A10/A18
DAC1
12
31
P2.1/A9/A17
P1.4/ADC4
13
14
30
P2.0/A8/A16
SDATA/ MOSI
18
19
20
21
22
23
24
25
26
27
28
P3.1/TXD
P3.2/INT0
P3.3/INT1/MISO
DVDD
DGND
P3.4/T0
P3.5/T1/CONVST
P3.6/WR
P3.7/RD
SCLOCK
29
P3.0/RXD
SDATA/MOSI
17
P2.2/A10/A18
RESET
P3.7/RD
P0.2/AD2
ADuC812
SCLOCK
P3.6/WR
P3.4/T0
47
6
P1.5/ADC5/ SS
P3.5/T1/CONVST
P0.3/AD3
DGND
AGND
14 15 16 17 18 19 20 21 22 23 24 25 26
DGND
48
38
27
P3.2/INT0
DGND
5
P2.1/A9/A17
28 P2.0/A8/A16
P3.3/INT1/MISO
DVDD
49
AVDD
29
P3.0/RxD
P3.1/TxD
DVDD
P2.4/A12/A20
DGND
34 DVDD
30
P1.7/ADC7
RESET
50
39
XTAL1
31 P2.3/A11/A19
P1.5/ADC5/SS 12
P1.6/ADC6 13
P0.4/AD4
4
32
P1.4/ADC4 11
51
P2.5/A13/A21
AVDD
16
VREF 8
DAC0 9
DAC1 10
P0.5/AD5
40
33
TOP VIEW
(Not to Scale)
52
P2.6/A14/A22
3
15
ADuC812
P0.6/AD6
P2.7/A15/A23
41
35
AGND 6
CREF 7
53
42
PIN 1
INDENTIFIER
P1.7/ADC7
P1.2/ADC2 3
P1.3/ADC3 4
AVDD 5
P0.7/AD7
56
P2.7/A15/A23
P2.6/A14/A22
P1.1/ADC1/ T2EX
38
39
PIN 1
IDENTIFIER
P1.6/ADC6
P1.0/ADC0/T2 1
P1.1/ADC1/T2EX 2
54
P1.0/ADC0/ T2
PSEN
EA
52 51 50 49 48 47 46 45 44 43 42 41 40
55
56-Lead LFCSP
P0.0/AD0
ALE
P0.1/AD1
P0.3/AD3
P0.2/AD2
DVDD
DGND
P0.5/AD5
P0.4/AD4
P0.7/AD7
P0.6/AD6
52-Lead MQFP
ORDERING GUIDE
Model
Temperature
Range
ADuC812BS
–40°C to +85°C
ADuC812BS
–40°C to +85°C
EVAL-ADuC812QS
EVAL-ADuC812QSP
Package
Description
Package
Option
52-Lead Metric Quad Flat Package
56-Lead Lead Frame Chip Scale Package
QuickStart Development System
QuickStart Development System Plus
S-52
CP-56
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although
the ADuC812 features proprietary ESD protection circuitry, permanent damage may occur on
devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are
recommended to avoid performance degradation or loss of functionality.
–6–
REV. E
ADuC812
PIN FUNCTION DESCRIPTIONS
Mnemonic
Type Function
DVDD
AVDD
CREF
VREF
P
P
I
I/O
AGND
P1.0–P1.7
G
I
ADC0–ADC7
T2
I
I
T2EX
I
SS
SDATA
SCLOCK
MOSI
MISO
DAC0
DAC1
RESET
I
I/O
I/O
I/O
I/O
O
O
I
P3.0–P3.7
I/O
RxD
TxD
INT0
I/O
O
I
INT1
I
T0
T1
CONVST
I
I
I
WR
RD
XTAL2
XTAL1
DGND
P2.0–P2.7
(A8–A15)
(A16–A23)
O
O
O
I
G
I/O
REV. E
Digital Positive Supply Voltage, 3 V or 5 V Nominal.
Analog Positive Supply Voltage, 3 V or 5 V Nominal.
Decoupling Input for On-Chip Reference. Connect 0.1 µF between this pin and AGND.
Reference Input/Output. This pin is connected to the internal reference through a series resistor and is the
reference source for the ADC. The nominal internal reference voltage is 2.5 V, which appears at the pin.
This pin can be overdriven by an external reference.
Analog Ground. Ground reference point for the analog circuitry.
Port 1 is an 8-bit input port only. Unlike other ports, Port 1 defaults to Analog Input mode. To configure
any of these Port Pins as a digital input, write a 0 to the port bit. Port 1 pins are multifunctional and share
the following functionality.
Analog Inputs. Eight single-ended analog inputs. Channel selection is via ADCCON2 SFR.
Timer 2 Digital Input. Input to Timer/Counter 2. When enabled, Counter 2 is incremented in response to a
1 to 0 transition of the T2 input.
Digital Input. Capture/Reload trigger for Counter 2; also functions as an Up/Down control input for
Counter 2.
Slave Select Input for the SPI Interface.
User selectable, I2C Compatible or SPI Data Input/Output Pin.
Serial Clock Pin for I2C Compatible or SPI Serial Interface Clock.
SPI Master Output/Slave Input Data I/O Pin for SPI Interface.
SPI Master Input/Slave Output Data I/O Pin for SPI Serial Interface.
Voltage Output from DAC0.
Voltage Output from DAC1.
Digital Input. A high level on this pin for 24 master clock cycles while the oscillator is running resets the
device. External power-on reset (POR) circuity must be implemented to drive the RESET pin as described
in the Power-On Reset Operation section.
Port 3 is a bidirectional port with internal pull-up resistors. Port 3 pins that have 1s written to them are
pulled high by the internal pull-up resistors; in that state they can be used as inputs. As inputs, Port 3 pins
being pulled externally low will source current because of the internal pull-up resistors. Port 3 pins also
contain various secondary functions that are described below.
Receiver Data Input (Asynchronous) or Data Input/Output (Synchronous) of Serial (UART) Port
Transmitter Data Output (Asynchronous) or Clock Output (Synchronous) of Serial (UART) Port
Interrupt 0, programmable edge or level triggered Interrupt input, INT0 can be programmed to one of two
priority levels. This pin can also be used as a gate control input to Timer 0.
Interrupt 1, programmable edge or level triggered Interrupt input, INT1 can be programmed to one of two
priority levels. This pin can also be used as a gate control input to Timer 1.
Timer/Counter 0 Input.
Timer/Counter 1 Input.
Active Low Convert Start Logic Input for the ADC Block when the External Convert Start Function is Enabled.
A low-to-high transition on this input puts the track-and-hold into its hold mode and starts conversion.
Write Control Signal, Logic Output. Latches the data byte from Port 0 into the external data memory.
Read Control Signal, Logic Output. Enables the external data memory to Port 0.
Output of the Inverting Oscillator Amplifier.
Input to the Inverting Oscillator Amplifier and to the Internal Clock Generator Circuits.
Digital Ground. Ground reference point for the digital circuitry.
Port 2 is a bidirectional port with internal pull-up resistors. Port 2 pins that have 1s written to them are
pulled high by the internal pull-up resistors; in that state they can be used as inputs. As inputs, Port 2
pins being pulled externally low will source current because of the internal pull-up resistors. Port 2 emits the
high order address bytes during fetches from external program memory and middle and high order address
bytes during accesses to the external 24-bit external data memory space.
–7–
ADuC812
PIN FUNCTION DESCRIPTIONS (continued)
Mnemonic
Type Function
PSEN
O
ALE
O
EA
I
P0.7–P0.0
(A0–A7)
I/O
Program Store Enable, Logic Output. This output is a control signal that enables the external program
memory to the bus during external fetch operations. It is active every six oscillator periods except during
external data memory accesses. This pin remains high during internal program execution. PSEN can also be
used to enable serial download mode when pulled low through a resistor on power-up or RESET.
Address Latch Enable, Logic Output. This output is used to latch the low byte (and page byte for 24-bit
address space accesses) of the address into external memory during normal operation. It is activated every
six oscillator periods except during an external data memory access.
External Access Enable, Logic Input. When held high, this input enables the device to fetch code from
internal program memory locations 0000H to 1FFFH. When held low, this input enables the device to fetch
all instructions from external program memory.
Port 0 is an 8-bit open-drain bidirectional I/O port. Port 0 pins that have 1s written to them float and in
that state can be used as high impedance inputs. Port 0 is also the multiplexed low order address and data
bus during accesses to external program or data memory. In this application, it uses strong internal pull-ups
when emitting 1s.
dependent upon the number of quantization levels in the digitization process; the more levels, the smaller the quantization
noise. The theoretical signal-to-(noise + distortion) ratio for an
ideal N-bit converter with a sine wave input is given by:
TERMINOLOGY
ADC SPECIFICATIONS
Integral Nonlinearity
This is the maximum deviation of any code from a straight line
passing through the endpoints of the ADC transfer function.
The endpoints of the transfer function are zero scale, a point
1/2 LSB below the first code transition, and full scale, a point
1/2 LSB above the last code transition.
Signal-to-(Noise + Distortion) = (6.02N + 1.76) dB
Thus for a 12-bit converter, this is 74 dB.
Total Harmonic Distortion
Differential Nonlinearity
This is the difference between the measured and the ideal 1 LSB
change between any two adjacent codes in the ADC.
Offset Error
This is the deviation of the first code transition (0000 . . . 000)
to (0000 . . . 001) from the ideal, i.e., +1/2 LSB.
Total Harmonic Distortion is the ratio of the rms sum of the
harmonics to the fundamental.
DAC SPECIFICATIONS
Relative Accuracy
Relative accuracy or endpoint linearity is a measure of the
maximum deviation from a straight line passing through the
endpoints of the DAC transfer function. It is measured after
adjusting for zero-scale error and full-scale error.
Full-Scale Error
This is the deviation of the last code transition from the ideal
AIN voltage (Full Scale – 1.5 LSB) after the offset error has
been adjusted out.
Voltage Output Settling Time
This is the amount of time it takes for the output to settle to a
specified level for a full-scale input change.
Signal-to-(Noise + Distortion) Ratio
This is the measured ratio of signal-to-(noise + distortion) at the
output of the ADC. The signal is the rms amplitude of the fundamental. Noise is the rms sum of all nonfundamental signals up
to half the sampling frequency (fS/2), excluding dc. The ratio is
–8–
Digital-to-Analog Glitch Impulse
This is the amount of charge injected into the analog output
when the inputs change state. It is specified as the area of the
glitch in nV sec.
REV. E
ADuC812
ARCHITECTURE, MAIN FEATURES
7FH
The ADuC812 is a highly integrated, true 12-bit data acquisition system. At its core, the ADuC812 incorporates a high
performance 8-bit (8052 compatible) MCU with on-chip
reprogrammable nonvolatile Flash program memory controlling a multichannel (eight input channels) 12-bit ADC.
2FH
BANKS
SELECTED
VIA
BITS IN PSW
The chip incorporates all secondary functions to fully support
the programmable data acquisition core. These secondary
functions include User Flash Memory, Watchdog Timer
(WDT), Power Supply Monitor (PSM), and various industrystandard parallel and serial interfaces.
BIT ADDRESSABLE SPACE
(BIT ADDRESSES 0FH–7FH)
20H
1FH
11
18H
17H
10
10H
0FH
PROGRAM MEMORY SPACE
READ ONLY
4 BANKS OF 8 REGISTERS
R0–R7
01
08H
07H
FFFFH
00
RESET VALUE OF
STACK POINTER
00H
EXTERNAL
PROGRAM
MEMORY
SPACE
Figure 2. Lower 128 Bytes of Internal RAM
MEMORY ORGANIZATION
As with all 8052 compatible devices, the ADuC812 has separate
address spaces for program and data memory as shown in Figure 1. Also as shown in Figure 1, an additional 640 bytes of
User Data Flash EEPROM are available to the user. The User
Data Flash Memory area is accessed indirectly via a group of
control registers mapped in the Special Function Register (SFR)
area in the Data Memory Space.
2000H
EA = 1
INTERNAL
8K BYTE
FLASH/EE
PROGRAM
MEMORY
1FFFH
EA = 0
EXTERNAL
PROGRAM
MEMORY
SPACE
The SFR space is mapped in the upper 128 bytes of internal data
memory space. The SFR area is accessed by direct addressing
only and provides an interface between the CPU and all on-chip
peripherals. A block diagram showing the programming model
of the ADuC812 via the SFR area is shown in Figure 3.
0000H
DATA MEMORY SPACE
READ/WRITE
9FH
(PAGE 159)
FFFFFFH
640 BYTES
FLASH/EE DATA
MEMORY
ACCESSED
INDIRECTLY
VIA SFR
CONTROL REGISTERS
00H
8K BYTE
ELECTRICALLY
REPROGRAMMABLE
NONVOLATILE
FLASH/EE PROGRAM
MEMORY
(PAGE 0)
INTERNAL
DATA MEMORY
SPACE
FFH
UPPER
128
80H
7FH
LOWER
128
00H
ACCESSIBLE
BY
INDIRECT
ADDRESSING
ONLY
ACCESSIBLE
BY
DIRECT
AND
INDIRECT
ADDRESSING
FFH
SPECIAL
FUNCTION
REGISTERS
ACCESSIBLE
BY DIRECT
ADDRESSING
ONLY
80H
EXTERNAL
DATA
MEMORY
SPACE
(24-BIT
ADDRESS
SPACE)
8051
COMPATIBLE
CORE
128-BYTE
SPECIAL
FUNCTION
REGISTER
AREA
AUTOCALIBRATING
8-CHANNEL
HIGH SPEED
12-BIT ADC
OTHER ON-CHIP
PERIPHERALS
TEMPERATURE
SENSOR
2 12-BIT DACs
SERIAL I/O
PARALLEL I/O
WDT
PSM
Figure 3. Programming Model
000000H
Figure 1. Program and Data Memory Maps
The lower 128 bytes of internal data memory are mapped as
shown in Figure 2. The lowest 32 bytes are grouped into four
banks of eight registers addressed as R0 through R7. The next
16 bytes (128 bits) above the register banks form a block of
bit addressable memory space at bit addresses 00H through 7FH.
REV. E
640-BYTE
ELECTRICALLY
REPROGRAMMABLE
NONVOLATILE
FLASH/EE DATA
MEMORY
–9–
ADuC812
OVERVIEW OF MCU-RELATED SFRs
Accumulator SFR
Power Control SFR
ACC is the Accumulator register and is used for math operations including addition, subtraction, integer multiplication and
division, and Boolean bit manipulations. The mnemonics for
accumulator-specific instructions refer to the Accumulator as A.
B SFR
The Power Control (PCON) register contains bits for power
saving options and general-purpose status flags as shown in
Table II.
SFR Address
Power-On Default Value
Bit Addressable
The B register is used with the ACC for multiplication and
division operations. For other instructions, it can be treated as a
general-purpose scratch pad register.
87H
00H
No
SMOD SERIPD INTOPD ALEOFF GF1
GF0
PD
IDL
Stack Pointer SFR
The SP register is the stack pointer and is used to hold an internal
RAM address that is called the “top of the stack.” The SP register
is incremented before data is stored during PUSH and CALL
executions. While the stack may reside anywhere in on-chip RAM,
the SP register is initialized to 07H after a reset. This causes the
stack to begin at location 08H.
Data Pointer
The Data Pointer is made up of three 8-bit registers: DPP (page
byte), DPH (high byte), and DPL (low byte). These are used to
provide memory addresses for internal and external code access
and external data access. It may be manipulated as a 16-bit
register (DPTR = DPH, DPL), although INC DPTR instructions
will automatically carry over to DPP, or as three independent
8-bit registers (DPP, DPH, and DPL).
Table II. PCON SFR Bit Designations
Bit
Name
Description
7
6
5
4
3
2
1
0
SMOD
———
———
ALEOFF
GF1
GF0
PD
IDL
Double UART Baud Rate
Reserved
Reserved
Disable ALE Output
General-Purpose Flag Bit
General-Purpose Flag Bit
Power-Down Mode Enable
Idle Mode Enable
Program Status Word SFR
The PSW register is the Program Status Word that contains
several bits reflecting the current status of the CPU as detailed
in Table I.
SFR Address
Power-On Default Value
Bit Addressable
CY
AC
F0
D0H
00H
Yes
RS1
RS0
OV
F1
P
Table I. PSW SFR Bit Designations
Bit
Name
Description
7
6
5
4
3
CY
AC
F0
RS1
RS0
2
1
0
OV
F1
P
Carry Flag
Auxiliary Carry Flag
General-Purpose Flag
Register Bank Select Bits
RS1
RS0
Selected Bank
0
0
0
0
1
1
1
0
2
1
1
3
Overflow Flag
General-Purpose Flag
Parity Bit
–10–
REV. E
ADuC812
SPECIAL FUNCTION REGISTERS
All registers except the program counter and the four general-purpose register banks reside in the special function register (SFR) area.
The SFR registers include control, configuration, and data registers that provide an interface between the CPU and other on-chip
peripherals.
Figure 4 shows a full SFR memory map and SFR contents on reset. Unoccupied SFR locations are shown dark shaded (NOT USED).
Unoccupied locations in the SFR address space are not implemented, i.e., no register exists at this location. If an unoccupied
location is read, an unspecified value is returned. SFR locations reserved for on-chip testing are shown lighter shaded (RESERVED)
and should not be accessed by user software. Sixteen of the SFR locations are also bit addressable and denoted by “1” i.e., the bit
addressable SFRs are those whose address ends in 0H or 8H.
ISPI
WCOL
SPE
SPIM
CPOL
CPHA
SPR1
SPR0
FFH
0 FEH
0 FDH
0 FCH
0 FBH
0 FAH
0 F9H
0 F8H
0
F7H
0 F6H
0 F5H
0 F4H
0 F3H
0 F2H
0 F1H
0 F0H
0
MDO
MDE
EFH
0 EEH
E7H
0 E6H
ADCI
DFH
PRE2
C7H
PSI
BFH
RD
B7H
EA
PT2
0 BDH
WR
1 B6H
0 EBH
T1
1 B5H
EADC
ET2
0 E2H
CS3
0 DBH
RS0
EXEN2
0 CBH
WDR1
0 C4H
PS
0 BCH
T0
1 B4H
ES
0 C3H
PT1
0 BBH
PX1
0 BAH
INT1
1 B3H
INT0
1 B2H
ET1
CS1
EX1
0
CS0
0 D8H
FI
0 D1H
0
P
0 D0H
CNT2
0 C9H
WDR2
0 C2H
0
0 E0H
0 D9H
TR2
0 CAH
I2CI
0 E8H
0 E1H
OV
0 D2H
I2CTX
0 E9H
CS2
0 DAH
0 D3H
TCLK
0 CCH
I2CRS
0 EAH
0 E3H
RS1
0 D4H
PRE0
0 C5H
PADC
0 BEH
0 DCH
RCLK
0 CDH
PRE1
0 C6H
0 E4H
F0
0 D5H
EXF2
0 CEH
I2CM
MDI
0 ECH
CCONV SCONV
0 DDH
AC
0 D6H
TF2
CFH
0 E5H
DMA
0 DEH
CY
D7H
MCO
0 EDH
0
CAP2
0 C8H
WDS
0 C1H
0
WDE
0 C0H
PT0
0 B9H
1 B1H
0
RxD
1
EX0
AFH
0 AEH
0 ADH
0 ACH
0 ABH
0 AAH
0 A9H
0 A8H
0
A7H
1 A6H
1 A5H
1 A4H
1 A3H
1 A2H
1 A1H
1 A0H
1
SM0
SM1
SM2
REN
TB8
RB8
TI
9FH
0 9EH
0 9DH
0 9CH
0 9BH
0 9AH
0 99H
97H
1 96H
1 95H
1 94H
1 93H
1 92H
1 91H
T2EX
TF1
TR1
TF0
TR0
IE1
IT1
RI
0 98H
0
T2
1 90H
IE0
1
IT0
8FH
0 8EH
0 8DH
0 8CH
0 8BH
0 8AH
0 89H
0 88H
0
87H
1 86H
1 85H
1 84H
1 83H
1 82H
1 81H
1 80H
1
SFR MAP KEY:
DAC0L
00H F9H
F0H
DAC0H
00H
FAH
00H
DAC1L
FBH
00H
DAC1H
FCH
00H
00H
F1H
00H
F2H
20H
F3H
00H
F4H
00H
IE0
89H
BITS
BITS
E0H
00H
SPIDAT
RESERVED
RESERVED
D8H
00H
PSW1
BITS
D0H
RESERVED
C8H
RESERVED
RESERVED
B8H
B0H
RESERVED
A8H
NOT USED
A0H
98H
90H
B9H
88H
IE2
00H
A9H
RESERVED
RESERVED
RESERVED
80H
00H
RCAP2L
00H
BAH
52H
0
PSMCON
DFH DEH
DMAH
D3H
00H
RCAP2H
CBH
00H
NOT USED
DMAP
D4H
TL2
CCH
RESERVED
ETIM2
BBH
04H
00H
ETIM3
EDATA1
BCH
RESERVED
RESERVED
RESERVED
RESERVED
00H
TH2
CDH 00H
RESERVED
EDARL
C6H
EDATA2
EDATA3
00H
BDH 00H
BEH
RESERVED
00H
00H
EDATA4
BFH
00H
NOT USED
NOT USED
NOT USED
NOT USED
NOT USED
NOT USED
NOT USED
NOT USED
NOT USED
NOT USED
NOT USED
NOT USED
NOT USED
NOT USED
NOT USED
NOT USED
NOT USED
NOT USED
NOT USED
NOT USED
NOT USED
NOT USED
NOT USED
NOT USED
NOT USED
NOT USED
NOT USED
NOT USED
00H
NOT USED
00H
SBUF
99H
I2CDAT
00H
NOT USED
9AH
00H
NOT USED
I2CADD
9BH
55H
NOT USED
FFH
00H
TMOD
89H
FFH
TL0
00H
SP
81H
TCON
IT0
RESERVED
FFH
P01
BITS
RESERVED
ETIM1
00H
NOT USED
TCON1
BITS
RESERVED
20H
FFH
P11, 3
BITS
RESERVED
C4H C9H
SCON1
BITS
00H
RESERVED
00H
NOT USED
ECON
00H
P21
BITS
RESERVED
RESERVED
DMAL
CAH
IE1
BITS
RESERVED
RESERVED
00H
P31
BITS
DAH
D2H
IP1
BITS
00H
00H
WDCON1
C0H
D9H
00H
T2CON1
BITS
RESERVED
EFH
ADCCON21 ADCDATAL ADCDATAH
BITS
F7H
00H
88H
DEFAULT VALUE
8AH
00H
TL1
8BH
DPL
07H
82H
00H
00H
DPH
83H
00H
TH0
8CH
00H
DPP
84H
00H
00H
MNEMONIC
DEFAULT VALUE
SFR ADDRESS
SFR NOTES
1SFRs WHOSE ADDRESS ENDS IN 0H OR 8H ARE BIT ADDRESSABLE.
2CALIBRATION COEFFICIENTS ARE PRECONFIGURED ON POWER-UP TO FACTORY CALIBRATED VALUES.
3THE PRIMARY FUNCTION OF PORT 1 IS AS AN ANALOG INPUT PORT; THEREFORE, TO ENABLE THE DIGITAL SECONDARY FUNCTIONS
ON THESE PORT PINS, WRITE A “0” TO THE CORRESPONDING PORT 1 SFR BIT.
Figure 4. Special Function Register Locations and Reset Values
REV. E
F5H
00H
ACC1
NOT USED
ADCCON1
RESERVED
E8H
0 88H
RESERVED
FDH 04H
I2CCON1
THESE BITS ARE CONTAINED IN THIS BYTE.
MNEMONIC
SFR ADDRESS
DACCON
ADCOFSL2 ADCOFSH2 ADCGAINL2 ADCGAINH2 ADCCON3
B1
BITS
BITS
PX0
1 B0H
ET0
F8H
0
0 B8H
TxD
SPICON1
BITS
–11–
TH1
8DH
00H
RESERVED
RESERVED
PCON
87H
00H
ADuC812
ADC CIRCUIT INFORMATION
General Overview
ADC Transfer Function
The ADC conversion block incorporates a fast, 8-channel,
12-bit, single-supply ADC. This block provides the user with
multichannel mux, track-and-hold, on-chip reference, calibration features, and ADC. All components in this block are easily
configured via a 3-register SFR interface.
The ADC consists of a conventional successive-approximation
converter based around a capacitor DAC. The converter accepts
an analog input range of 0 V to VREF. A high precision, low drift
and factory calibrated 2.5 V reference is provided on-chip. The
internal reference may be overdriven via the external VREF pin.
This external reference can be in the range 2.3 V to AVDD.
The analog input range for the ADC is 0 V to VREF. For this
range, the designed code transitions occur midway between
successive integer LSB values (i.e., 1/2 LSB, 3/2 LSBs,
5/2 LSBs . . . FS –3/2 LSBs). The output coding is straight
binary with 1 LSB = FS/4096 or 2.5 V/4096 = 0.61 mV when
VREF = 2.5 V. The ideal input/output transfer characteristic for
the 0 to VREF range is shown in Figure 5.
OUTPUT
CODE
111...111
111...110
111...101
111...100
Single step or continuous conversion modes can be initiated in
software or alternatively by applying a convert signal to an external
pin. Timer 2 can also be configured to generate a repetitive trigger
for ADC conversions. The ADC may be configured to operate
in a DMA mode whereby the ADC block continuously converts
and captures samples to an external RAM space without any
interaction from the MCU core. This automatic capture facility
can extend through a 16 MByte external Data Memory space.
1LSB =
FS
4096
000...011
000...010
000...001
000...000
0V 1LSB
The ADuC812 is shipped with factory programmed calibration
coefficients that are automatically downloaded to the ADC on
power-up, ensuring optimum ADC performance. The ADC
core contains internal offset and gain calibration registers.
A software calibration routine is provided to allow the user to
overwrite the factory programmed calibration coefficients if
required, thus minimizing the impact of endpoint errors in the
user’s target system.
A voltage output from an on-chip band gap reference proportional to absolute temperature can also be routed through the
front end ADC multiplexer (effectively a ninth ADC channel
input) facilitating a temperature sensor implementation.
VOLTAGE INPUT
+FS
–1LSB
Figure 5. ADC Transfer Function
Typical Operation
Once configured via the ADCCON 1–3 SFRs (shown on the
following page), the ADC will convert the analog input and
provide an ADC 12-bit result word in the ADCDATAH/L SFRs.
The top four bits of the ADCDATAH SFR will be written
with the channel selection bits to identify the channel result.
The format of the ADC 12-bit result word is shown in Figure 6.
ADCDATAH SFR
CH–ID
TOP 4 BITS
HIGH 4 BITS OF
ADC RESULT WORD
ADCDATAL SFR
LOW 8 BITS OF THE
ADC RESULT WORD
Figure 6. ADC Result Format
–12–
REV. E
ADuC812
ADCCON1—(ADC Control SFR #1)
The ADCCON1 register controls conversion and acquisition times, hardware conversion modes and power-down modes as
detailed below.
SFR Address
EFH
SFR Power-On Default Value
20H
MD1
MD0
CK1
CK0
AQ1
AQ0
T2C
EXC
Table III. ADCCON1 SFR Bit Designations
Bit
Name
Description
ADCCON1.7 MD1
ADCCON1.6 MD0
The mode bits (MD1, MD0) select the active operating mode of the ADC as follows:
MD1 MD0 Active Mode
0
0
ADC powered down
0
1
ADC normal mode
1
0
ADC powered down if not executing a conversion cycle
1
1
ADC standby if not executing a conversion cycle
Note: In power-down mode the ADC VREF circuits are maintained on, whereas all ADC peripherals are
powered down, thus minimizing current consumption.
ADCCON1.5 CK1
ADCCON1.4 CK0
The ADC clock divide bits (CK1, CK0) select the divide ratio for the master clock used to generate the
ADC clock. A typical ADC conversion will require 17 ADC clocks. The divider ratio is selected
as follows:
CK1 CK0 MCLK Divider
0
0
1
0
1
2
1
0
4
1
1
8
ADCCON1.3 AQ1
ADCCON1.2 AQ0
The ADC acquisition select bits (AQ1, AQ0) select the time provided for the input track-and-hold
amplifier to acquire the input signal, and are selected as follows:
AQ1 AQ0 #ADC Clks
0
0
1
0
1
2
1
0
4
1
1
8
ADCCON1.1 T2C
The Timer 2 conversion bit (T2C) is set by the user to enable the Timer 2 overflow bit be used as
the ADC convert start trigger input. ADC conversions are initiated on the second Timer 2 overflow.
ADCCON1.0 EXC
The external trigger enable bit (EXC) is set by the user to allow the external CONVST pin to be
used as the active low convert start input. This input should be an active low pulse (minimum
pulsewidth >100 ns) at the required sample rate.
REV. E
–13–
ADuC812
ADCCON2—(ADC Control SFR #2)
The ADCCON2 register controls ADC channel selection and conversion modes as detailed below.
SFR Address
SFR Power-On Default Value
ADCI
DMA
D8H
00H
CCONV
SCONV
CS3
CS2
CS1
CS0
Table IV. ADCCON2 SFR Bit Designations
Location
Name
ADCCON2.7 ADCI
ADCCON2.6 DMA
ADCCON2.5 CCONV
ADCCON2.4 SCONV
ADCCON2.3
ADCCON2.2
ADCCON2.1
ADCCON2.0
CS3
CS2
CS1
CS0
Description
The ADC interrupt bit (ADCI) is set by hardware at the end of a single ADC conversion cycle or at the
end of a DMA block conversion. ADCI is cleared by hardware when the PC vectors to the ADC Interrupt
Service Routine.
The DMA mode enable bit (DMA) is set by the user to enable a preconfigured ADC DMA mode operation.
A more detailed description of this mode is given in the ADC DMA Mode section.
The continuous conversion bit (CCONV) is set by the user to initiate the ADC into a continuous mode
of conversion. In this mode, the ADC starts converting based on the timing and channel configuration
already set up in the ADCCON SFRs; the ADC automatically starts another conversion once a previous
conversion has completed.
The single conversion bit (SCONV) is set to initiate a single conversion cycle. The SCONV bit is
automatically reset to “0” on completion of the single conversion cycle.
The channel selection bits (CS3–0) allow the user to program the ADC channel selection under
software control. When a conversion is initiated, the channel converted will be the one pointed to by
these channel selection bits. In DMA mode, the channel selection is derived from the channel ID
written to the external memory.
CS3 CS2 CS1 CS0 CH#
0
0
0
0
0
0
0
0
1
1
0
0
1
0
2
0
0
1
1
3
0
1
0
0
4
0
1
0
1
5
0
1
1
0
6
0
1
1
1
7
1
0
0
0
Temp Sensor
1
1
1
1
DMA STOP
All other combinations reserved.
ADCCON3—(ADC Control SFR #3)
The ADCCON3 register gives user software an indication of ADC busy status.
SFR Address
SFR Power-On Default Value
BUSY
RSVD
F5H
00H
RSVD
RSVD
RSVD
RSVD
RSVD
RSVD
Table V. ADCCON3 SFR Bit Designations
Bit Location
Bit Status
Description
ADCCON3.7 BUSY
The ADC busy status bit (BUSY) is a read-only status bit that is set during a valid ADC conversion
or calibration cycle. BUSY is automatically cleared by the core at the end of conversion or calibration.
ADCCON3.6
ADCCON3.5
ADCCON3.4
ADCCON3.3
ADCCON3.2
ADCCON3.1
ADCCON3.0
ADCCON3.0–3.6 are reserved (RSVD) for internal use. These bits will read as “0” and should only
be written as “0” by user software.
RSVD
RSVD
RSVD
RSVD
RSVD
RSVD
RSVD
–14–
REV. E
ADuC812
Driving the ADC
The ADC incorporates a successive approximation (SAR) architecture involving a charge-sampled input stage. Figure 7 shows
the equivalent circuit of the analog input section. Each ADC
conversion is divided into two distinct phases as defined by the
position of the switches in Figure 7. During the sampling phase
(with SW1 and SW2 in the “track” position), a charge proportional to the voltage on the analog input is developed across the
input sampling capacitor. During the conversion phase (with
both switches in the “hold” position), the capacitor DAC is
adjusted via internal SAR logic until the voltage on node A is zero,
indicating that the sampled charge on the input capacitor is
balanced out by the charge being output by the capacitor DAC.
The digital value finally contained in the SAR is then latched
out as the result of the ADC conversion. Control of the SAR,
and timing of acquisition and sampling modes, is handled
automatically by built-in ADC control logic. Acquisition and
conversion times are also fully configurable under user control.
ADC0
TEMPERATURE
SENSOR
ADuC812
ADC7
200
TRACK
SW1
HOLD
CAPACITOR
DAC
2pF
ADuC812
51
1
ADC0
0.01F
Figure 8. Buffering Analog Inputs
sampling capacitor can draw its charge. Since the 0.01 µF capacitor
in Figure 8 is more than 4096 times the size of the 2 pF sampling
capacitor, its voltage will not change by more than one count
(1/4096) of the 12-bit transfer function when the 2 pF charge
from a previous channel is dumped onto it. A larger capacitor
can be used if desired, but not a larger resistor (for reasons
described below).
The Schottky diodes in Figure 8 may be necessary to limit the
voltage applied to the analog input pin as per the Absolute Maximum Ratings. They are not necessary if the op amp is powered
from the same supply as the ADuC812 since in that case, the
op amp is unable to generate voltages above VDD or below ground.
An op amp is necessary unless the signal source is very low impedance to begin with. DC leakage currents at the ADuC812’s analog
inputs can cause measurable dc errors with external source impedances of as little as 100 Ω. To ensure accurate ADC operation,
keep the total source impedance at each analog input less than
61 Ω. The table below illustrates examples of how source
impedance can affect dc accuracy.
Source
Impedance
Error from 1 A
Leakage Current
Error from 10 A
Leakage Current
61 Ω
610 Ω
61 µV = 0.1 LSB
610 µV = 1 LSB
610 µV = 1 LSB
61 mV = 10 LSB
NODE A
SW2
TRACK
HOLD
COMPARATOR
AGND
Figure 7. Internal ADC Structure
Note that whenever a new input channel is selected, a residual
charge from the 2 pF sampling capacitor places a transient on
the newly selected input. The signal source must be capable of
recovering from this transient before the sampling switches click
into “hold” mode. Delays can be inserted in software (between
channel selection and conversion request) to account for input
stage settling, but a hardware solution will alleviate this burden
from the software design task and will ultimately result in a
cleaner system implementation. One hardware solution would
be to choose a very fast settling op amp to drive each analog
input. Such an op amp would need to settle fully from a small
signal transient in less than 300 ns to guarantee adequate settling
under all software configurations. A better solution, recommended
for use with any amplifier, is shown in Figure 8.
Though at first glance the circuit in Figure 8 may look like a
simple antialiasing filter, it actually serves no such purpose since
its corner frequency is well above the Nyquist frequency, even at
a 200 kHz sample rate. Though the R/C does help to reject some
incoming high frequency noise, its primary function is to ensure
that the transient demands of the ADC input stage are met. It
does so by providing a capacitive bank from which the 2 pF
REV. E
Although Figure 8 shows the op amp operating at a gain of 1,
you can configure it for any gain needed. Also, you can use an
instrumentation amplifier in its place to condition differential
signals. Use any modern amplifier that is capable of delivering
the signal (0 to VREF) with minimal saturation. Some single-supply,
rail-to-rail op amps that are useful for this purpose include, but
are not limited to, the ones given in Table VI. Check Analog
Devices literature (CD ROM data book, and so on) for details
about these and other op amps and instrumentation amps.
Table VI. Some Single-Supply Op Amps
Op Amp Model
Characteristics
OP181/OP281/OP481
OP191/OP291/OP491
OP196/OP296/OP496
OP183/OP283
OP162/OP262/OP462
AD820/AD822/AD824
AD823
Micropower
I/O Good up to VDD, Low Cost
I/O to VDD, Micropower, Low Cost
High Gain-Bandwidth Product
High GBP, Micro Package
FET Input, Low Cost
FET Input, High GBP
Keep in mind that the ADC’s transfer function is 0 V to VREF,
and any signal range lost to amplifier saturation near ground will
impact dynamic range. Though the op amps in Table VI are
capable of delivering output signals very closely approaching
ground, no amplifier can deliver signals all the way to ground when
powered by a single supply. Therefore, if a negative supply is
available, consider using it to power the front end amplifiers.
–15–
ADuC812
However, be sure to include the Schottky diodes shown in
Figure 8 (or at least the lower of the two diodes) to protect the
analog input from undervoltage conditions. To summarize this
section, use the circuit of Figure 8 to drive the analog input pins
of the ADuC812.
ADuC812
VDD
51
EXTERNAL
VOLTAGE
REFERENCE
VREF
Voltage Reference Connections
The on-chip 2.5 V band gap voltage reference can be used as
the reference source for the ADC and DACs. To ensure the
accuracy of the voltage reference, decouple both the VREF pin and
the CREF pin to ground with 0.1 µF ceramic chip capacitors as
shown in Figure 9.
2.5V
BAND GAP
REFERENCE
BUFFER
0.1F
CREF
0.1F
Figure 10. Using an External Voltage Reference
ADuC812
Configuring the ADC
51
BUFFER
VREF
2.5V
BAND GAP
REFERENCE
The three SFRs (ADCCON1, ADCCON2, ADCCON3) configure the ADC. In nearly all cases, an acquisition time of one
ADC clock (ADCCON1.2 = 0, ADCCON1.3 = 0) will provide
plenty of time for the ADuC812 to acquire its signal before
switching the internal track-and-hold amplifier into hold mode.
The only exception would be a high source impedance analog
input, but these should be buffered first anyway since source
impedances of greater than 610 Ω can cause dc errors as well.
BUFFER
0.1F
CREF
0.1F
Figure 9. Decoupling VREF and CREF
The internal voltage reference can also be tapped directly from
the VREF pin, if desired, to drive external circuitry. However, a
buffer must be used to ensure that no current is drawn from the
VREF pin itself. The voltage on the CREF pin is that of an internal
node within the buffer block, and its voltage is critical to ADC
and DAC accuracy. Do not connect anything to this pin except
the capacitor, and be sure to keep trace-lengths short on the
CREF capacitor, decoupling the node straight to the underlying
ground plane.
The ADuC812 powers up with its internal voltage reference in the
“off” state. The voltage reference turns on automatically whenever
the ADC or either DAC gets enabled in software. Once enabled,
the voltage reference requires approximately 65 ms to power up
and settle to its specified value. Be sure that your software allows
this time to elapse before initiating any conversions. If an external
voltage reference is preferred, connect it to the VREF pin as shown
in Figure 10 to overdrive the internal reference.
To ensure accurate ADC operation, the voltage applied to VREF
must be between 2.3 V and AVDD. In situations where analog
input signals are proportional to the power supply (such as some
strain gage applications), it may be desirable to connect the
VREF pin directly to AVDD. In such a configuration, the user
must also connect the CREF pin directly to AVDD to circumvent
internal buffer headroom limitations. This allows the ADC
input transfer function to span the full range of 0 V to AVDD
accurately.
Operation of the ADC or DACs with a reference voltage below
2.3 V, however, may incur loss of accuracy resulting in missing
codes or nonmonotonicity. For that reason, do not use a reference
voltage less than 2.3 V.
The ADuC812’s successive approximation ADC is driven by a
divided down version of the master clock. To ensure adequate
ADC operation, this ADC clock must be between 400 kHz and
4 MHz, and optimum performance is obtained with ADC clock
between 400 kHz and 3 MHz. Frequencies within this range can
be achieved with master clock frequencies from 400 kHz to well
above 16 MHz with the four ADC clock divide ratios to choose
from. For example, with a 12 MHz master clock, set the ADC
clock divide ratio to 4 (i.e., ADCCLK = MCLK/4 = 3 MHz) by
setting the appropriate bits in ADCCON1 (ADCCON1.5 = 1,
ADCCON1.4 = 0).
The total ADC conversion time is 15 ADC clocks, plus one
ADC clock for synchronization, plus the selected acquisition
time (1, 2, 3, or 4 ADC clocks). For the example above, with a
one clock acquisition time, total conversion time is 17 ADC clocks
(or 5.67 µs for a 3 MHz ADC clock).
In continuous conversion mode, a new conversion begins each
time the previous one finishes. The sample rate is the inverse of the
total conversion time described above. In the example above, the
continuous conversion mode sample rate would be 176.5 kHz.
ADC DMA Mode
The on-chip ADC has been designed to run at a maximum
conversion speed of 5 µs (200 kHz sampling rate). When converting at this rate, the ADuC812 MicroConverter has 5 µs to
read the ADC result and store the result in memory for further
postprocessing, otherwise the next ADC sample could be lost.
In an interrupt driven routine, the MicroConverter would also
have to jump to the ADC Interrupt Service routine, which will
also increase the time required to store the ADC results. In
applications where the ADuC812 cannot sustain the interrupt
rate, an ADC DMA mode is provided.
To enable DMA mode, Bit 6 in ADCCON2 (DMA) must be set.
This allows the ADC results to be written directly to a 16 MByte
external static memory SRAM (mapped into data memory space)
–16–
REV. E
ADuC812
without any interaction from the ADuC812 core. This mode
allows the ADuC812 to capture a contiguous sample stream at
full ADC update rates (200 kHz).
00000AH
DMA Mode Configuration Example
To set the ADuC812 into DMA mode, a number of steps must
be followed.
1. The ADC must be powered down by setting MD1 and MD0
to 0 in ADCCON1.
2. The DMA Address pointer must be set to the start address of
where the ADC results are to be written. This is done by
writing to the DMA mode Address Pointers DMAL, DMAH,
and DMAP. DMAL must be written to first, followed by
DMAH, and then DMAP.
000000H
000000H
1
1
1
1
STOP COMMAND
0
0
1
1
REPEAT LAST CHANNEL
FOR A VALID STOP
CONDITION
0
0
1
1
CONVERT ADC CH#3
1
0
0
0
CONVERT TEMP SENSOR
0
1
0
1
CONVERT ADC CH#5
0
0
1
0
CONVERT ADC CH#2
1
STOP COMMAND
0
0
1
1
NO CONVERSION
RESULT WRITTEN HERE
0
0
1
1
CONVERSION RESULT
FOR ADC CH#3
1
0
0
0
CONVERSION RESULT
FOR TEMP SENSOR
0
1
0
1
CONVERSION RESULT
FOR ADC CH#5
0
0
1
0
CONVERSION RESULT
FOR ADC CH#2
CONVERT CHANNEL READ DURING PREVIOUS DMA CYCLE
WRITE ADC RESULT
CONVERTED DURING
PREVIOUS DMA CYCLE
READ CHANNEL ID
TO BE CONVERTED DURING
NEXT DMA CYCLE
DMA CYCLE
Figure 13. DMA Cycle
From the previous diagram, it can be seen that during one DMA
cycle the following actions are performed by the DMA logic.
1. An ADC conversion is performed on the channel whose ID
was read during the previous cycle.
2. The 12-bit result and the channel ID of the conversion performed in the previous cycle are written to the external memory.
3. The ID of the next channel to be converted is read from
external memory.
4. The DMA is initiated by writing to the ADC SFRs in the
following sequence.
For the previous example, the complete flow of events is shown
in Figure 13. Because the DMA logic uses pipelining, it takes
three cycles before the first correct result is written out.
a. ADCCON2 is written to enable the DMA mode, i.e.,
MOV ADCCON2, #40H; DMA mode enabled.
Micro Operation during ADC DMA Mode
b. ADCCON1 is written to configure the conversion time and
power-up of the ADC. It can also enable Timer 2 driven
conversions or External Triggered conversions if required.
c. ADC conversions are initiated by starting single/continuous
conversions, starting Timer 2 running for Timer 2 conversions, or by receiving an external trigger.
When the DMA conversions are completed, the ADC interrupt
bit ADCI is set by hardware and the external SRAM contains the
new ADC conversion results as shown in Figure 12. It should be
noted that no result is written to the last two memory locations.
REV. E
1
The DMA logic operates from the ADC clock and uses pipelining
to perform the ADC conversions and access the external memory
at the same time. The time it takes to perform one ADC conversion is called a DMA cycle. The actions performed by the logic
during a typical DMA cycle are shown in Figure 13.
Figure 11. Typical DMA External Memory Preconfiguration
When the DMA mode logic is active, it is responsible for storing
the ADC results away from both the user and ADuC812 core
logic. As it writes the results of the ADC conversions to external
memory, it takes over the external memory interface from the core.
Thus, any core instructions that access the external memory
while DMA mode is enabled will not gain access to it. The core
will execute the instructions and they will take the same time to
execute, but they will not gain access to the external memory.
1
Figure 12. Typical External Memory Configuration Post
ADC DMA Operation
3. The external memory must be preconfigured. This consists of
writing the required ADC channel IDs into the top four bits of
every second memory location in the external SRAM, starting
at the first address specified by the DMA address pointer. As the
ADC DMA mode operates independently of the ADuC812
core, it is necessary to provide it with a stop command. This is
done by duplicating the last channel ID to be converted, followed by “1111” into the next channel selection field. Figure 11
shows a typical preconfiguration of external memory.
00000AH
1
During ADC DMA mode, the MicroConverter core is free to
continue code execution, including general housekeeping and
communication tasks. However, it should be noted that MCU core
accesses to Ports 0 and 2 (which are being used by the DMA
controller) are gated OFF during ADC DMA mode of operation.
This means that even though the instruction that accesses the
external Ports 0 or 2 will appear to execute, no data will be seen
at these external ports as a result.
The MicroConverter core can be configured with an interrupt
to be triggered by the DMA controller when it has finished
filling the requested block of RAM with ADC results, allowing
the service routine for this interrupt to postprocess data without
any real-time timing constraints.
Offset and Gain Calibration Coefficients
The ADuC812 has two ADC calibration coefficients, one for offset
calibration and one for gain calibration. Both the offset and gain
calibration coefficients are 14-bit words, located in the Special
Function Register (SFR) area. The offset calibration coefficient
is divided into ADCOFSH (six bits) and ADCOFSL (eight bits),
–17–
ADuC812
and the gain calibration coefficient is divided into ADCGAINH
(six bits) and ADCGAINL (eight bits). The offset calibration
coefficient compensates for dc offset errors in both the ADC and
the input signal.
EPROM
TECHNOLOGY
Increasing the offset coefficient compensates for positive offset,
and effectively pushes the ADC transfer function DOWN. Decreasing the offset coefficient compensates for negative offset,
and effectively pushes the ADC transfer function UP. The
maximum offset that can be compensated is typically ±5% of
VREF, which equates to typically ±125 mV with a 2.5 V reference.
Similarly, the gain calibration coefficient compensates for dc gain
errors in both the ADC and the input signal.
Increasing the gain coefficient compensates for a smaller analog
input signal range and scales the ADC transfer function UP,
effectively increasing the slope of the transfer function. Decreasing
the gain coefficient compensates for a larger analog input signal
range and scales the ADC transfer function DOWN, effectively
decreasing the slope of the transfer function. The maximum analog
input signal range for which the gain coefficient can compensate
is 1.025 ⫻ VREF, and the minimum input range is 0.975 ⫻ VREF,
which equates to ±2.5% of the reference voltage.
Calibration
Each ADuC812 is calibrated in the factory prior to shipping, and
the offset and gain calibration coefficients are stored in a hidden
area of FLASH/EE memory. Each time the ADuC812 powers up,
an internal power-on configuration routine copies these coefficients
into the offset and gain calibration registers in the SFR area.
The MicroConverter ADC accuracy may vary from system
to system due to board layout, grounding, clock speed, and so
on. To get the best ADC accuracy in your system, perform
the software calibration routine described in Application Note
uC005, available from the MicroConverter homepage at
www.analog.com/microconverter.
EEPROM
TECHNOLOGY
IN-CIRCUIT
REPROGRAMMABLE
SPACE EFFICIENT/
DENSITY
FLASH/EE MEMORY
TECHNOLOGY
Figure 14. Flash Memory Development
Overall, Flash/EE memory represents a step closer to the ideal
memory device that includes nonvolatility, in-circuit programmability, high density, and low cost. Incorporated in the ADuC812,
Flash/EE memory technology allows the user to update program
code space in-circuit without replacing one-time programmable
(OTP) devices at remote operating nodes.
Flash/EE Memory and the ADuC812
The ADuC812 provides two arrays of Flash/EE memory for user
applications. 8K bytes of Flash/EE program space are provided
on-chip to facilitate code execution without any external discrete
ROM device requirements. The program memory can be programmed using conventional third party memory programmers.
This array can also be programmed in-circuit, using the serial
download mode provided.
A 640 byte Flash/EE data memory space is also provided on-chip
as a general-purpose nonvolatile scratchpad area. User access to
this area is via a group of six SFRs.
ADuC812 Flash/EE Memory Reliability
The Flash/EE program and data memory arrays on the ADuC812
are fully qualified for two key Flash/EE memory characteristics:
Flash/EE Memory Cycling Endurance and Flash/EE Memory
Data Retention.
Endurance quantifies the ability of the Flash/EE memory to be
cycled through many program, read, and erase cycles. In real
terms, a single endurance cycle is composed of four independent
sequential events:
NONVOLATILE FLASH MEMORY
Flash Memory Overview
a.
b.
c.
d.
The ADuC812 incorporates Flash memory technology on-chip
to provide the user with a nonvolatile, in-circuit reprogrammable
code and data memory space.
Flash/EE memory is a relatively new type of nonvolatile memory
technology based on a single transistor cell architecture.
This technology is basically an outgrowth of EPROM technology
and was developed in the late 1980s. Flash/EE memory takes the
flexible in-circuit reprogrammable features of EEPROM and
combines them with the space efficient/density features of EPROM
(see Figure 14).
Because Flash/EE technology is based on a single transistor cell
architecture, a Flash memory array, like EPROM, can be implemented to achieve the space efficiencies or memory densities
required by a given design.
Like EEPROM, Flash memory can be programmed in-system
at a byte level, although it must first be erased in page blocks.
Thus, Flash memory is often and more correctly referred to as
Flash/EE memory.
Initial Page Erase Sequence
Read/Verify Sequence
Byte Program Sequence
Second Read/Verify Sequence
In reliability qualification, every byte in the program and data
Flash/EE memory is cycled from 00H to FFH until the first fail is
recorded, signifying the endurance limit of the on-chip Flash/EE
memory.
As indicated in the Specification tables, the ADuC812 Flash/EE
Memory Endurance qualification has been carried out in accordance with JEDEC Specification A117 over the industrial
temperature ranges of –40°C, +25°C, and +85°C. The results
allow the specification of a minimum endurance figure over supply
and temperature of 10,000 cycles, with an endurance figure of
50,000 cycles being typical of operation at 25°C.
Retention quantifies the ability of the Flash/EE memory to retain
its programmed data over time. Again, the ADuC812 has been
qualified in accordance with the formal JEDEC Retention Lifetime
Specification (A117) at a specific junction temperature (TJ = 55°C).
As part of this qualification procedure, the Flash/EE memory is
cycled to its specified endurance limit described above, before data
retention is characterized. This means that the Flash/EE memory
is guaranteed to retain its data for its full specified retention
lifetime every time the Flash/EE memory is reprogrammed.
–18–
REV. E
ADuC812
Using the Flash/EE Program Memory
This 8K byte Flash/EE program memory array is mapped
into the lower 8K bytes of the 64K bytes program space addressable by the ADuC812 and will be used to hold user code in
typical applications.
Using the Flash/EE Data Memory
The user Flash/EE data memory array consists of 640 bytes that
are configured into 160 (Page 00H to Page 9FH) 4-byte pages,
as shown in Figure 16.
The program memory array can be programmed in one of
two modes:
9FH
BYTE 1
BYTE 2
BYTE 3
BYTE 4
00H
BYTE 1
BYTE 2
BYTE 3
BYTE 4
Serial Downloading (In-Circuit Programming)
As part of its embedded download/debug kernel, the ADuC812
facilitates serial code download via the standard UART serial port.
Serial download mode is automatically entered on power-up if the
external pin PSEN is pulled low through an external resistor as
shown in Figure 15. Once in this mode, the user can download code
to the program memory array while the device is sited in its target
application hardware. A PC serial download executable is provided
as part of the ADuC812 QuickStart development system.
The Serial Download protocol is detailed in a MicroConverter
Applications Note uC004, available from the ADI MicroConverter
website at www.analog.com/micronverter.
Figure 16. User Flash/EE Memory Configuration
As with other ADuC812 user peripheral circuits, the interface to
this memory space is via a group of registers mapped in the SFR
space. A group of four data registers (EDATA1–4) is used to hold
the 4-byte page being accessed. EADRL is used to hold the 8-bit
address of the page being accessed. Finally, ECON is an
8-bit control register that may be written with one of five Flash/EE
memory access commands to trigger various read, write, erase,
and verify functions. These register can be summarized as follows:
ECON:
EADRL:
SFR Address
Function
Default
SFR Address
Function
Default
B9H
Controls access to 640 bytes
Flash/EE data space.
00H
C6H
Holds the Flash/EE data
page address. 0H through 9FH
00H
EDATA1–4:
SFR Address
Function
PULL PSEN LOW DURING RESET TO
CONFIGURE THE ADuC812 FOR
SERIAL DOWNLOAD MODE
ADuC812
Default
BCH to BFH, respectively
Holds the Flash/EE data
memory page write or page
read data bytes.
EDATA1–4➝00H
PSEN
1k
A block diagram of the SFR registered interface to the data
Flash/EE memory array is shown in Figure 17.
Figure 15. Flash/EE Memory Serial Download Mode
Programming
FUNCTION:
HOLDS THE 8-BIT PAGE
ADDRESS POINTER
Parallel Programming
9FH
The parallel programming mode is fully compatible with
conventional third party Flash or EEPROM device programmers.
In this mode, Ports P0, P1, and P2 operate as the external data
and address bus interface, ALE operates as the Write Enable
strobe, and Port P3 is used as a general configuration port that
configures the device for various program and erase operations
during parallel programming.
BYTE 1 BYTE 2 BYTE 3 BYTE 4
EADRL
EDATA1 (BYTE 1)
00H
BYTE 1 BYTE 2 BYTE 3 BYTE 4
EDATA2 (BYTE 2)
EDATA3 (BYTE 3)
EDATA4 (BYTE 4)
ECON COMMAND
INTERPRETER LOGIC
The high voltage (12 V) supply required for Flash programming
is generated using on-chip charge pumps to supply the high
voltage program lines.
FUNCTION:
HOLDS COMMAND WORD
The complete parallel programming specification is available on the
MicroConverter homepage at www.analog.com/microconverter.
REV. E
FUNCTION:
HOLDS THE 4-BYTE
PAGE WORD
ECON
FUNCTION:
INTERPRETS THE FLASH
COMMAND WORD
Figure 17. User Flash/EE Memory Control and
Configuration
–19–
ADuC812
ECON—Flash/EE Memory Control SFR
Using the Flash/EE Memory Interface
This SFR acts as a command interpreter and may be written
with one of five command modes to enable various read, program, and erase cycles as detailed in Table VII.
As with all Flash/EE memory architectures, the array can be programmed in system at a byte level, although it must be erased
first, the erasure being performed in page blocks (4-byte pages
in this case).
Table VII. ECON—Flash/EE Memory Control Register
Command Modes
Command Byte
Command Mode
01H
READ COMMAND
Results in four bytes being read into
EDATA1–4 from memory page address
contained in EADRL.
PROGRAM COMMAND
Results in four bytes (EDATA1–4) being
written to memory page address in EADRL.
This write command assumes the designated
“write” page has been pre-erased.
RESERVED FOR INTERNAL USE
03H should not be written to the
ECON SFR.
VERIFY COMMAND
Allows the user to verify if data in EDATA1–4
is contained in page address designated by
EADRL.
A subsequent read of the ECON SFR will
result in a zero being read if the verification
is valid; a nonzero value will be read to
indicate an invalid verification.
ERASE COMMAND
Results in an erase of the 4-byte page
designated in EADRL.
ERASE-ALL COMMAND
Results in erase of the full Flash/EE data
memory 160-page (640 bytes) array.
RESERVED COMMANDS
Commands reserved for future use.
02H
03H
04H
05H
06H
07H to FFH
Flash/EE Memory Timing
The typical program/erase times for the Flash/EE data
memory are:
Erase Full Array (640 Bytes)
Erase Single Page (4 Bytes)
Program Page (4 Bytes)
Read Page (4 Bytes)
–
–
–
–
20 ms
20 ms
250 µs
Within Single Instruction Cycle
Flash/EE erase and program timing is derived from the master
clock. When using a master clock frequency of 11.0592 MHz, it
is not necessary to write to the ETIM registers at all. However,
when operating at other master clock frequencies (fCLK), you
must change the values of ETIM1 and ETIM2 to avoid degrading data Flash/EE endurance and retention. ETIM1 and ETIM2
form a 16-bit word, ETIM2 being the high byte and ETIM1 the
low byte. The value of this 16-bit word must be set as follows to
ensure optimum data Flash/EE endurance and retention.
A typical access to the Flash/EE array will involve setting up the
page address to be accessed in the EADRL SFR, configuring the
EDATA1–4 with data to be programmed to the array (the
EDATA SFRs will not be written for read accesses), and finally
writing the ECON command word that initiates one of the six
modes shown in Table VII. It should be noted that a given
mode of operation is initiated as soon as the command word is
written to the ECON SFR. The core microcontroller operation
on the ADuC812 is idled until the requested Program/Read or
Erase mode is completed.
In practice, this means that even though the Flash/EE memory
mode of operation is typically initiated with a two-machine cycle
MOV instruction (to write to the ECON SFR), the next instruction
will not be executed until the Flash/EE operation is complete
(250 µs or 20 ms later). This means that the core will not respond
to Interrupt requests until the Flash/EE operation is complete,
although the core peripheral functions like Counter/Timers will
continue to count and time as configured throughout this pseudoidle period.
Erase-All
Although the 640-byte user Flash/EE array is shipped from the
factory pre-erased, i.e., byte locations set to FFH, it is nonetheless
good programming practice to include an erase-all routine as
part of any configuration/setup code running on the ADuC812.
An ERASE-ALL command consists of writing 06H to the
ECON SFR, which initiates an erase of all 640 byte locations in
the Flash/EE array. This command coded in 8051 assembly
would appear as:
MOV ECON, #06H
; Erase all Command
; 20 ms Duration
Program a Byte
In general terms, a byte in the Flash/EE array can only be programmed if it has previously been erased. To be more specific, a
byte can only be programmed if it already holds the value FFH.
Because of the Flash/EE architecture, this erasure must happen
at a page level; therefore, a minimum of four bytes (1 page) will
be erased when an erase command is initiated. A more specific
example of the Program-Byte process is shown below. In this
example, the user writes F3H into the second byte on Page 03H
of the Flash/EE data memory space while preserving the other
three bytes already in this page. As the user is only required to
modify one of the page bytes, the full page must be first read so that
this page can then be erased without the existing data being lost.
This example, coded in 8051 assembly, would appear as:
MOV
MOV
MOV
MOV
MOV
ETIM2, ETIM1 = 100 µs × fCLK
EADRL, #03H
ECON, #01H
EDATA2, #0F3H
ECON, #05H
ECON, #02H
;
;
;
;
;
Set Page Address Pointer
Read Page
Write New Byte
Erase Page
Write Page (Program
Flash/EE)
ETIM3 should always remain at its default value of 201 dec/C9 hex.
–20–
REV. E
ADuC812
USER INTERFACE TO OTHER ON-CHIP ADuC812
PERIPHERALS
The following section gives a brief overview of the various
peripherals also available on-chip. A summary of the SFRs used
to control and configure these peripherals is also given.
DAC
The ADuC812 incorporates two 12-bit voltage output DACs
on-chip. Each has a rail-to-rail voltage output buffer capable
DACCON
DAC Control
Register
SFR Address
Power-On Default Value
Bit Addressable
FDH
04H
No
MODE
RNG1
RNG0
of driving 10 kΩ/100 pF. Each has two selectable ranges, 0 V to
VREF (the internal band gap 2.5 V reference) and 0 V to AVDD.
Each can operate in 12-bit or 8-bit mode. Both DACs share a
control register, DACCON, and four data registers, DAC1H/L,
DAC0H/L. It should be noted that in 12-bit asynchronous mode,
the DAC voltage output will be updated as soon as the DACL
data SFR has been written; therefore, the DAC data registers
should be updated as DACH first, followed by DACL.
CLR1
CLR0
SYNC
PD1
PD0
Table VIII. DACCON SFR Bit Designations
Bit
Name
Description
7
MODE
6
RNG1
5
RNG0
4
CLR1
3
CLR0
2
SYNC
1
PD1
0
PD0
The DAC MODE bit sets the overriding operating mode for both DACs.
Set to “1” = 8-bit mode (Write eight Bits to DACxL SFR).
Set to “0” = 12-bit mode.
DAC1 Range Select Bit.
Set to “1” = DAC1 range 0–VDD.
Set to “0” = DAC1 range 0–VREF.
DAC0 Range Select Bit.
Set to “1” = DAC0 range 0–VDD.
Set to “0” = DAC0 range 0–VREF.
DAC1 Clear Bit.
Set to “0” = DAC1 output forced to 0 V.
Set to “1” = DAC1 output normal.
DAC0 Clear Bit.
Set to “0” = DAC1 output forced to 0 V.
Set to “1” = DAC1 output normal.
DAC0/1 Update Synchronization Bit.
When set to “1” the DAC outputs update as soon as DACxL SFRs are written. The user can
simultaneously update both DACs by first updating the DACxL/H SFRs while SYNC is “0.” Both
DACs will then update simultaneously when the SYNC bit is set to “1.”
DAC1 Power-Down Bit.
Set to “1” = Power-on DAC1.
Set to “0” = Power-off DAC1.
DAC0 Power-Down Bit.
Set to “1” = Power-on DAC0.
Set to “0” = Power-off DAC0.
DACxH/L
DAC Data Registers
Function
SFR Address
DAC data registers, written by user to update the DAC output.
DAC0L (DAC0 Data Low Byte) ➝F9H; DAC1L (DAC1 data low byte)➝FBH
DAC0H (DAC0 Data High Byte) ➝FAH; DAC1H(DAC1 data high byte)➝FCH
➝All four registers
00H
➝All four registers
No
Power-On Default Value
Bit Addressable
The 12-bit DAC data should be written into DACxH/L, right-justified such that DACL contains the lower eight bits, and the lower
nibble of DACH contains the upper four bits.
REV. E
–21–
ADuC812
Using the DAC
VDD
The on-chip DAC architecture consists of a resistor string DAC
followed by an output buffer amplifier, the functional equivalent
of which is illustrated in Figure 18. Details of the actual DAC
architecture can be found in U.S. Patent Number 5969657
(www.uspto.gov). Features of this architecture include inherent
guaranteed monotonicity and excellent differential linearity.
VDD – 50mV
VDD – 100mV
AVDD
ADuC812
100mV
R
R
OUTPUT
BUFFER
R
R
50mV
0mV
000 HEX
8
FFF HEX
Figure 19. Endpoint Nonlinearities Due to Amplifier
Saturation
HIGH-Z
DISABLE
(FROM MCU)
R
Figure 18. Resistor String DAC Functional Equivalent
As illustrated in Figure 18, the reference source for each DAC is
user selectable in software. It can be either AVDD or VREF. In
0-to-AVDD mode, the DAC output transfer function spans from
0 V to the voltage at the AVDD pin. In 0-to-VREF mode, the
DAC output transfer function spans from 0 V to the internal
VREF, or if an external reference is applied, the voltage at the
VREF pin. The DAC output buffer amplifier features a true rail-torail output stage implementation. This means that unloaded, each
output is capable of swinging to within less than 100 mV of both
AVDD and ground. Moreover, the DAC’s linearity specification
(when driving a 10 kΩ resistive load to ground) is guaranteed
through the full transfer function except codes 0 to 48, and, in
0-to-AVDD mode only, codes 3995 to 4095. Linearity degradation
near ground and VDD is caused by saturation of the output
amplifier, and a general representation of its effects (neglecting
offset and gain error) is illustrated in Figure 19. The dotted line
in Figure 19 indicates the ideal transfer function, and the solid
line represents what the transfer function might look like with
endpoint nonlinearities due to saturation of the output amplifier. Note
that Figure 19 represents a transfer function in 0-to-VDD mode
only. In 0-to-VREF mode (with VREF < VDD) the lower nonlinearity
would be similar, but the upper portion of the transfer function
would follow the “ideal” line right to the end (VREF in this case,
not VDD), showing no signs of endpoint linearity errors.
The endpoint nonlinearities conceptually illustrated in Figure 19
get worse as a function of output loading. Most of the ADuC812’s
data sheet specifications assume a 10 kΩ resistive load to ground
at the DAC output. As the output is forced to source or sink
more current, the nonlinear regions at the top or bottom
(respectively) of Figure 19 become larger. With larger current
demands, this can significantly limit output voltage swing.
Figure 20 and Figure 21 illustrate this behavior. It should be noted
that the upper trace in each of these figures is only valid for an
output range selection of 0-to-AVDD. In 0-to-VREF mode, DAC
loading will not cause high-side voltage drops as long as the
reference voltage remains below the upper trace in the corresponding figure. For example, if AVDD = 3 V and VREF = 2.5 V, the
high-side voltage will not be affected by loads less than 5 mA.
But somewhere around 7 mA the upper curve in Figure 21 drops
below 2.5 V (VREF), indicating that at these higher currents the
output will not be capable of reaching VREF.
5
DAC LOADED WITH 0FFF HEX
4
OUTPUT VOLTAGE – V
VREF
3
2
1
DAC LOADED WITH 0000 HEX
0
0
5
10
SOURCE/SINK CURRENT – mA
15
Figure 20. Source and Sink Current Capability with
VREF = VDD = 5 V
–22–
REV. E
ADuC812
the DAC outputs will remain at ground potential whenever the
DAC is disabled. However, each DAC output will still spike
briefly when power is first applied to the chip, and again when
each DAC is first enabled in software. Typical scope shots of
these spikes are given in Figure 23 and Figure 24, respectively.
OUTPUT VOLTAGE – V
3
2
200s/DIV
AVDD – 2V/DIV
1
0
0
5
10
SOURCE/SINK CURRENT – mA
15
Figure 21. Source and Sink Current Capability with
VREF = VDD = 3 V
DAC OUT – 500mV/DIV
To drive significant loads with the DAC outputs, external
buffering may be required, as illustrated in Figure 22.
Figure 23. DAC Output Spike at Chip Power-Up
5s/DIV, 1V/DIV
9
ADuC812
10
Figure 22. Buffering the DAC Outputs
The DAC output buffer also features a high impedance disable
function. In the chip’s default power-on state, both DACs are
disabled, and their outputs are in a high impedance state (or
“three-state”) where they remain inactive until enabled in software.
This means that if a zero output is desired during power-up or
power-down transient conditions, then a pull-down resistor must
be added to each DAC output. Assuming this resistor is in place,
REV. E
Figure 24. DAC Output Spike at DAC Enable
–23–
ADuC812
user program fails to set the watchdog timer refresh bits (WDR1,
WDR2) within a predetermined amount of time (see PRE2–0
bits in WDCON). The watchdog timer itself is a 16-bit counter.
The watchdog timeout interval can be adjusted via the PRE2–0 bits
in WDCON. Full Control and Status of the watchdog timer function
can be controlled via the watchdog timer control SFR (WDCON).
WATCHDOG TIMER
The purpose of the watchdog timer is to generate a device reset
within a reasonable amount of time if the ADuC812 enters an
erroneous state, possibly due to a programming error. The Watchdog function can be disabled by clearing the WDE (Watchdog
Enable) bit in the Watchdog Control (WDCON) SFR. When
enabled, the watchdog circuit will generate a system reset if the
WDCON
Watchdog Timer
Control Register
SFR Address
Power-On Default Value
Bit Addressable
C0H
00H
Yes
PRE2
PRE1
PRE0
—
WDR1
WDR2
WDS
WDE
Table IX. WDCON SFR Bit Designations
Bit
Name
Description
7
6
5
PRE2
PRE1
PRE0
Watchdog Timer Prescale Bits.
4
3
2
1
—
WDR1
WDR2
WDS
0
WDE
PRE2
PRE1
PRE0
Timeout Period (ms)
0
0
0
16
0
0
1
32
0
1
0
64
0
1
1
128
1
0
0
256
1
0
1
512
1
1
0
1024
1
1
1
2048
Not Used.
Watchdog Timer Refresh Bits. Set sequentially to refresh the watchdog timer.
Watchdog Status Bit.
Set by the Watchdog Controller to indicate that a watchdog timeout has occurred.
Cleared by writing a “0” or by an external hardware reset. It is not cleared by a watchdog reset.
Watchdog Enable Bit.
Set by user to enable the watchdog and clear its counters.
Example
POWER SUPPLY MONITOR
To set up the watchdog timer for a timeout period of 2048 ms,
the following code would be used:
As its name suggests, the Power Supply Monitor, once enabled,
monitors both supplies (AVDD and DVDD) on the ADuC812. It
will indicate when either power supply drops below one of five
user selectable voltage trip points from 2.63 V to 4.63 V. For
correct operation of the Power Supply Monitor function, AVDD
must be equal to or greater than 2.7 V. The Power Supply
Monitor function is controlled via the PSMCON SFR. If
enabled via the IE2 SFR, the Power Supply Monitor will interrupt
the core using the PSMI bit in the PSMCON SFR. This bit will
not be cleared until the failing power supply has returned
above the trip point for at least 256 ms. This ensures that the
power supply has fully settled before the bit is cleared. This
monitor function allows the user to save working registers to avoid
possible data loss due to the low supply condition, and also ensures
that normal code execution will not resume until a safe supply
level has been well established. The supply monitor is also
protected against spurious glitches triggering the interrupt circuit.
MOV
WDCON,#0E0h
;2.048 second
;timeout period
SETB
WDE
;enable watchdog timer
To prevent the watchdog timer from timing out, the timer
refresh bits need to be set before 2.048 seconds has elapsed.
SETB
WDR1
;refresh watchdog timer..
SETB
WDR2
; ..bits must be set in this
;order
–24–
REV. E
ADuC812
PSMCON
Power Supply Monitor
Control Register
SFR Address
Power-On Default Value
Bit Addressable
DFH
DCH
No
—
CMP
PSMI
TP2
TP1
TP0
PSF
PSMEN
Table X. PSMCON SFR Bit Designations
Bit
Name
Description
7
6
—
CMP
5
PSMI
4
TP2
Not Used.
AVDD and DVDD Comparator Bit.
This is a read-only bit and directly reflects the state of the AVDD and DVDD comparators.
Read “1” indicates that both the AVDD and DVDD supplies are above their selected trip points.
Read “0” indicates that either the AVDD or DVDD supply is below its selected trip point.
Power Supply Monitor Interrupt Bit.
This bit will be set high by the MicroConverter if CMP is low, indicating low analog or digital
supply. The PSMI bit can be used to interrupt the processor. Once CMPD and/or CMP return
(and remain) high, a 256 ms counter is started. When this counter times out, the PSMI interrupt
is cleared. PSMI can also be written by the user. However, if either comparator output is low,
it is not possible for the user to clear PSMI.
VDD Trip Point Selection Bits.
3
2
TP1
TP0
1
PSF
0
PSMEN
These bits select the AVDD and DVDD trip point voltage as follows:
TP2
TP1
TP0
Selected DVDD Trip Point (V)
0
0
0
4.63
0
0
1
4.37
0
1
0
3.08
0
1
1
2.93
1
0
0
2.63
AVDD/DVDD Fault Indicator.
Read “1” indicates that the AVDD supply caused the fault condition.
Read “0” indicates that the DVDD supply caused the fault condition.
Power Supply Monitor Enable Bit.
Set to “1” by the user to enable the Power Supply Monitor Circuit.
Cleared to “0” by the user to disable the Power Supply Monitor Circuit.
Example
To configure the PSM for a trip point of 4.37 V, the following
code would be used:
MOV
PSMCON,#005h
;enable PSM with
;4.37V threshold
SETB
EA
;enable interrupts
MOV
IE2,#002h
;enable PSM
;interrupt
If the supply voltage falls below this level, the PC would vector
to the ISR.
ORG
CHECK:MOV
JB
RETI
REV. E
0043h
A,PSMCON
;PSM ISR
;PSMCON.5 is the
;PSM interrupt
;bit..
ACC.5,CHECK
;..it is cleared
;only when Vdd
;has remained
;above the trip
;point for 256ms
;or more.
; return only when "all's well"
SERIAL PERIPHERAL INTERFACE
The ADuC812 integrates a complete hardware Serial Peripheral
Interface (SPI) on-chip. SPI is an industry-standard synchronous
serial interface that allows eight bits of data to be synchronously
transmitted and received simultaneously, i.e., full duplex. It should
be noted that the SPI pins are shared with the I2C interface, and
therefore the user can only enable one or the other interface at
any given time (see SPE in Table XI). The SPI Port can be configured for Master or Slave operation and typically consists of
four pins, namely:
MISO (Master In, Slave Out Data I/O Pin)
The MISO (master in, slave out) pin is configured as an input
line in master mode and an output line in slave mode. The
MISO line on the master (data in) should be connected to the
MISO line in the slave device (data out). The data is transferred
as byte wide (8-bit) serial data, MSB first.
–25–
ADuC812
MOSI (Master Out, Slave In Pin)
The MOSI (master out, slave in) pin is configured as an output
line in master mode and an input line in slave mode. The
MOSI line on the master (data out) should be connected to the
MOSI line in the slave device (data in). The data is transferred as
byte wide (8-bit) serial data, MSB first.
SCLOCK (Serial Clock I/O Pin)
The master serial clock (SCLOCK) is used to synchronize the
data being transmitted and received through the MOSI and MISO
data lines. A single data bit is transmitted and received in each
SCLOCK period. Therefore, a byte is transmitted/received after
eight SCLOCK periods. The SCLOCK pin is configured as an
output in master mode and as an input in slave mode. In master
mode, the bit rate, polarity, and phase of the clock are controlled
by the CPOL, CPHA, SPR0, and SPR1 bits in the SPICON SFR
(see Table XI). In slave mode, the SPICON register will have to
be configured with the phase and polarity (CPHA and CPOL) of
the expected input clock. In both master and slave modes, the
SPICON
SFR Address
Power-On Default Value
Bit Addressable
ISPI
WCOL
data is transmitted on one edge of the SCLOCK signal and
sampled on the other. It is important therefore that the CPHA
and CPOL are configured the same for the master and slave
devices.
SS (Slave Select Input Pin)
The Slave Select (SS) input pin is shared with the ADC5 input.
To configure this pin as a digital input, the bit must be cleared,
e.g., CLR P1.5.
This line is active low. Data is only received or transmitted in
slave mode when the SS pin is low, allowing the ADuC812 to
be used in single master, multislave SPI configurations. If
CPHA = 1, then the SS input may be permanently pulled low.
With CPHA = 0, the SS input must be driven low before the
first bit in a byte wide transmission or reception, and return
high again after the last bit in that byte wide transmission or
reception. In SPI Slave mode, the logic level on the external SS
pin can be read via the SPR0 bit in the SPICON SFR. The following SFR registers are used to control the SPI interface.
SPI Control
Register
F8H
OOH
Yes
SPE
SPIM
CPOL
CPHA
SPR1
SPR0
Table XI. SPICON SFR Bit Designations
Bit
Name
Description
7
ISPI
6
WCOL
5
SPE
4
SPIM
3
CPOL*
2
CPHA*
1
0
SPR1
SPR0
SPI Interrupt Bit.
Set by MicroConverter at the end of each SPI transfer.
Cleared directly by user code or indirectly by reading the SPIDAT SFR.
Write Collision Error Bit.
Set by MicroConverter if SPIDAT is written to while an SPI transfer is in progress.
Cleared by user code.
SPI Interface Enable Bit.
Set by user to enable the SPI interface.
Cleared by user to enable I2C interface.
SPI Master/Slave Mode Select Bit.
Set by user to enable Master mode operation (SCLOCK is an output).
Cleared by user to enable Slave mode operation (SCLOCK is an input).
Clock Polarity Select Bit.
Set by user if SCLOCK idles high.
Cleared by user if SCLOCK idles low.
Clock Phase Select Bit.
Set by user if leading SCLOCK edge is to transmit data.
Cleared by user if trailing SCLOCK edge is to transmit data.
SPI Bit Rate Select Bits.
These bits select the SCLOCK rate (bit rate) in Master mode as follows:
SPR1
SPR0
Selected Bit Rate
0
0
fOSC/4
0
1
fOSC/8
1
0
fOSC/32
1
1
fOSC/64
In SPI Slave mode, i.e., SPIM = 0, the logic level on the external SS pin can be read
via the SPR0 bit.
*The CPOL and CPHA bits should both contain the same values for master and slave devices.
–26–
REV. E
ADuC812
SPIDAT
Function
SPI Data Register
The SPIDAT SFR is written by the
user to transmit data over the SPI
interface or read by user code to read
data just received by the SPI interface.
SFR Address
Power-On Default Value
Bit Addressable
F7H
00H
No
Using the SPI Interface
Depending on the configuration of the bits in the SPICON SFR
shown in Table XI, the ADuC812 SPI interface will transmit or
receive data in a number of possible modes. Figure 25 shows all
possible ADuC812 SPI configurations and the timing relationships
and synchronization between the signals involved. Also shown in
this figure is the SPI interrupt bit (ISPI) and how it is triggered
at the end of each byte wide communication.
SCLOCK
(CPOL = 1)
SPI Interface—Master Mode
In master mode, the SCLOCK pin is always an output and generates a burst of eight clocks whenever user code writes to the
SPIDAT register. The SCLOCK bit rate is determined by SPR0
and SPR1 in SPICON. It should also be noted that the SS pin
is not used in master mode. If the ADuC812 needs to assert the
SS pin on an external slave device, a Port digital output pin
should be used.
In master mode a byte transmission or reception is initiated by
a write to SPIDAT. Eight clock periods are generated via the
SCLOCK pin and the SPIDAT byte being transmitted via MOSI.
With each SCLOCK period a data bit is also sampled via
MISO. After eight clocks, the transmitted byte will have been
completely transmitted and the input byte will be waiting in
the input shift register. The ISPI flag will be set automatically
and an interrupt will occur if enabled. The value in the shift
register will be latched into SPIDAT.
SPI Interface—Slave Mode
In slave mode the SCLOCK is an input. The SS pin must also
be driven low externally during the byte communication.
SCLOCK
(CPOL = 0)
SS
(CPHA = 1)
SAMPLE INPUT
DATA OUTPUT
? MSB
BIT 6
BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 LSB
ISPI FLAG
(CPHA = 0)
SAMPLE INPUT
DATA OUTPUT
MSB
BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 LSB ?
Transmission is also initiated by a write to SPIDAT. In slave mode,
a data bit is transmitted via MISO and a data bit is received via
MOSI through each input SCLOCK period. After eight clocks,
the transmitted byte will have been completely transmitted and
the input byte will be waiting in the input shift register. The
ISPI flag will be set automatically and an interrupt will occur
if enabled. The value in the shift register will be latched into
SPIDAT only when the transmission/reception of a byte has been
completed. The end of transmission occurs after the eighth
clock has been received if CPHA = 1, or when SS returns high
if CPHA = 0.
ISPI FLAG
Figure 25. SPI Timing, All Modes
REV. E
–27–
ADuC812
I2C* COMPATIBLE INTERFACE
The ADuC812 supports a 2-wire serial interface mode that is
I2C compatible. The I2C compatible interface shares its pins with
the on-chip SPI interface and therefore the user can only enable
one or the other interface at any given time (see SPE in Table IX).
An application note describing the operation of this interface as
implemented is available from the MicroConverter website at
www.analog.com/microconverter. This interface can be configured
as a software master or hardware slave, and uses two pins in the
interface.
MDO
MDE
MCO
SDATA
SCLOCK
Serial Data I/O Pin
Serial Clock
Three SFRs are used to control the I2C compatible interface.
These are described below:
I2CCON
SFR Address
Power-On Default Value
Bit Addressable
MDI
I2CM
I2CRS
I2C Control Register
E8H
00H
Yes
I2CTX
I2CI
Table XII. I2CCON SFR Bit Designations
Bit
Name
Description
7
MDO
6
MDE
5
MCO
4
MDI
3
I2CM
2
I2CRS
1
I2CTX
0
I2CI
I2C Software Master Data Output Bit (Master Mode Only).
This data bit is used to implement a master I2C transmitter interface in software. Data written to
this bit will be output on the SDATA pin if the data output enable (MDE) bit is set.
I2C Software Master Data Output Enable Bit (Master Mode Only).
Set by the user to enable the SDATA pin as an output (Tx). Cleared by the user to enable SDATA
pin as an input (Rx).
I2C Software Master Data Output Bit (Master Mode Only).
This data bit is used to implement a master I2C transmitter interface in software. Data written to
this bit will be output on the SCLOCK pin.
I2C Software Master Data Input Bit (Master Mode Only).
This data bit is used to implement a master I2C receiver interface in software. Data on the
SDATA pin is latched into this bit on SCLOCK if the Data Output Enable (MDE) = 0.
I2C Master/Slave Mode Bit.
Set by user to enable I2C software master mode. Cleared by user to enable I2C hardware slave mode.
I2C Reset Bit (Slave Mode Only).
Set by user to reset the I2C interface. Cleared by user for normal I2C operation.
I2C Direction Transfer Bit (Slave Mode Only).
Set by the MicroConverter if the interface is transmitting. Cleared by the MicroConverter if the
interface is receiving.
I2C Interrupt Bit (Slave Mode Only).
Set by the MicroConverter after a byte has been transmitted or received. Cleared by user software.
I2C Address Register
Holds the I2C peripheral address for
the part. It may be overwritten by
the user code. Application note uC001
at www.analog.com/microconverter
describes the format of the I2C
standard 7-bit address in detail.
SFR Address
9BH
Power-On Default Value 55H
Bit Addressable
No
I2CADD
Function
I2C Data Register
The I2CDAT SFR is written by the
user to transmit data over the I2C
interface or read by user code to read
data just received by the I2C interface.
User software should only access
I2CDAT once per interrupt cycle.
SFR Address
9AH
Power-On Default Value 00H
Bit Addressable
No
I2CDAT
Function
*Purchase of licensed I2C components of Analog Devices or one of its sublicensed Associated Companies conveys a license for the purchaser under the Philips
I2C Patent Rights to use these components in an I2C system, provided that the system conforms to the I2C Standard Specification as defined by Philips.
–28–
REV. E
ADuC812
8051 COMPATIBLE ON-CHIP PERIPHERALS
This section gives a brief overview of the various secondary
peripheral circuits that are also available to the user on-chip.
These remaining functions are fully 8051 compatible and are
controlled via standard 8051 SFR bit definitions.
Parallel I/O Ports 0–3
The ADuC812 uses four input/output ports to exchange data with
external devices. In addition to performing general-purpose I/O,
some ports are capable of external memory operations; others
are multiplexed with an alternate function for the peripheral
features on the device. In general, when a peripheral is enabled,
that pin may not be used as a general-purpose I/O pin.
Port 0 is an 8-bit, open-drain, bidirectional I/O port that is directly
controlled via the P0 SFR (SFR address = 80H). Port 0 pins
that have 1s written to them via the Port 0 SFR will be configured
as open-drain and will therefore float. In that state, Port 0 pins can
be used as high impedance inputs. An external pull-up resistor
will be required on Port 0 outputs to force a valid logic high
level externally. Port 0 is also the multiplexed low order address
and data bus during accesses to external program or data memory.
In this application, it uses strong internal pull-ups when emitting 1s.
Port 3 is a bidirectional port with internal pull-ups directly
controlled via the P3 SFR (SFR address = B0H). Port 3 pins
that have 1s written to them are pulled high by the internal pull-ups
and, in that state, can be used as inputs. As inputs, Port 3 pins
being pulled externally low will source current because of the internal
pull-ups. Port 3 pins also have various secondary functions
described in Table XIV.
Table XIV. Port 3, Alternate Pin Functions
Pin
Alternate Function
P3.0
RxD (UART Input Pin)
(or Serial Data I/O in Mode 0)
TxD (UART Output Pin)
(or Serial Clock Output in Mode 0)
INT0 (External Interrupt 0)
INT1 (External Interrupt 1)
T0 (Timer/Counter 0 External Input)
T1 (Timer/Counter 1 External Input)
WR (External Data Memory Write Strobe)
RD (External Data Memory Read Strobe)
P3.1
P3.2
P3.3
P3.4
P3.5
P3.6
P3.7
Port 1 is also an 8-bit port directly controlled via the P1 SFR
(SFR address = 90H). Port 1 is an input only port. Port 1 digital
output capability is not supported on this device. Port 1 pins can
be configured as digital inputs or analog inputs.
The alternate functions of P1.0, P1.1, P1.5, and Port 3 pins
can be activated only if the corresponding bit latch in the P1
and P3 SFRs contains a 1. Otherwise, the port pin is stuck at 0.
By (power-on) default these pins are configured as analog inputs,
i.e., “1” written in the corresponding Port 1 register bit. To
configure any of these pins as digital inputs, the user should write
a “0” to these port bits to configure the corresponding pin as a
high impedance digital input.
The ADuC812 has three 16-bit Timer/Counters: Timer 0,
Timer 1, and Timer 2. The Timer/Counter hardware has been
included on-chip to relieve the processor core of the overhead
inherent in implementing timer/counter functionality in software.
Each Timer/Counter consists of two 8-bit registers, THx and
TLx (x = 0, 1, and 2). All three can be configured to operate
either as timers or event counters.
These pins also have various secondary functions described in
Table XIII.
Table XIII. Port 1, Alternate Pin Functions
Pin
Alternate Function
P1.0
P1.1
P1.5
T2 (Timer/Counter 2 External Input)
T2EX (Timer/Counter 2 Capture/Reload Trigger)
SS (Slave Select for the SPI Interface)
Port 2 is a bidirectional port with internal pull-up resistors directly
controlled via the P2 SFR (SFR address = A0H). Port 2 pins
that have 1s written to them are pulled high by the internal pull-up
resistors and, in that state, can be used as inputs. As inputs, Port
2 pins being pulled externally low will source current because of
the internal pull-up resistors. Port 2 emits the high order
address bytes during fetches from external program memory,
and middle and high order address bytes during accesses to the
24-bit external data memory space.
REV. E
Timers/Counters
In Timer function, the TLx register is incremented every machine
cycle. Thus, think of it as counting machine cycles. Since a
machine cycle consists of 12 core clock periods, the maximum
count rate is 1/12 of the core clock frequency.
In Counter function, the TLx register is incremented by a 1-to-0
transition at its corresponding external input pin, T0, T1, or T2.
In this function, the external input is sampled during S5P2 of
every machine cycle. When the samples show a high in one cycle and
a low in the next cycle, the count is incremented. The new count
value appears in the register during S3P1 of the cycle following the
one in which the transition was detected. Since it takes two machine
cycles (24 core clock periods) to recognize a 1-to-0 transition,
the maximum count rate is 1/24 of the core clock frequency.
There are no restrictions on the duty cycle of the external input
signal, but to ensure that a given level is sampled at least once
before it changes, it must be held for a minimum of one full
machine cycle.
–29–
ADuC812
User configuration and control of all Timer operating modes is achieved via three SFRs:
TMOD, TCON
Control and configuration for Timers 0 and 1.
T2CON
Control and configuration for Timer 2.
TMOD
Timer/Counter 0 and
1 Mode Register
SFR Address
Power-On Default Value
Bit Addressable
89H
00H
No
Gate
C/T
M1
M0
Gate
C/T
M1
M0
Table XV. TMOD SFR Bit Designations
Bit
Name
Description
7
Gate
6
C/T
5
4
M1
M0
3
Gate
2
C/T
1
0
M1
M0
Timer 1 Gating Control.
Set by software to enable Timer/Counter 1 only while INT1 pin is high and TR1 control bit is set.
Cleared by software to enable Timer 1 whenever TR1 control bit is set.
Timer 1 Timer or Counter Select Bit.
Set by software to select counter operation (input from T1 pin).
Cleared by software to select timer operation (input from internal system clock).
Timer 1 Mode Select Bit 1 (used with M0 Bit).
Timer 1 Mode Select Bit 0.
M1
M0
0
0
TH1 operates as an 8-bit timer/counter. TL1 serves as 5-bit prescaler.
0
1
16-Bit Timer/Counter. TH1 and TL1 are cascaded; there is no prescaler.
1
0
8-Bit Autoreload Timer/Counter. TH1 holds a value that is to be
reloaded into TL1 each time it overflows.
1
1
Timer/Counter 1 Stopped.
Timer 0 Gating Control.
Set by software to enable Timer/Counter 0 only while INT0 pin is high and TR0 control bit is set.
Cleared by software to enable Timer 0 whenever TR0 control bit is set.
Timer 0 Timer or Counter Select Bit.
Set by software to select counter operation (input from T0 pin).
Cleared by software to select timer operation (input from internal system clock).
Timer 0 Mode Select Bit 1.
Timer 0 Mode Select Bit 0.
M1
M0
0
0
TH0 operates as an 8-bit timer/counter. TL0 serves as 5-bit prescaler.
0
1
16-Bit Timer/Counter. TH0 and TL0 are cascaded; there is no prescaler.
1
0
8-Bit Autoreload Timer/Counter. TH0 holds a value that is to be
reloaded into TL0 each time it overflows.
1
1
TL0 is an 8-bit timer/counter controlled by the standard timer 0 control
bits. TH0 is an 8-bit timer only, controlled by Timer 1 control bits.
–30–
REV. E
ADuC812
TCON
Timer/Counter 0 and
1 Control Register
SFR Address
Power-On Default Value
Bit Addressable
88H
00H
Yes
TF1
TR1
TF0
IE1*
TR0
IT1*
IE0*
IT0*
*These bits are not used in the control of Timer/Counter 0 and 1, but are used instead in the control and monitoring of the external INT0 and INT1 interrupt pins.
Table XVI. TCON SFR Bit Designations
Bit
Name
Description
7
TF1
6
TR1
5
TF0
4
TR0
3
IE1
2
IT1
1
IE0
0
IT0
Timer 1 Overflow Flag.
Set by hardware on a Timer/Counter 1 overflow.
Cleared by hardware when the Program Counter (PC) vectors to the interrupt service routine.
Timer 1 Run Control Bit.
Set by user to turn on Timer/Counter 1.
Cleared by user to turn off Timer/Counter 1.
Timer 0 Overflow Flag.
Set by hardware on a Timer/Counter 0 overflow.
Cleared by hardware when the PC vectors to the interrupt service routine.
Timer 0 Run Control Bit.
Set by user to turn on Timer/Counter 0.
Cleared by user to turn off Timer/Counter 0.
External Interrupt 1 (INT1) Flag.
Set by hardware by a falling edge or zero level being applied to external interrupt pin INT1,
depending on bit IT1 state.
Cleared by hardware when the when the PC vectors to the interrupt service routine only if the
interrupt was transition-activated. If level-activated, the external requesting source controls the
request flag, rather than the on-chip hardware.
External Interrupt 1 (IE1) Trigger Type.
Set by software to specify edge-sensitive detection (i.e., 1-to-0 transition).
Cleared by software to specify level-sensitive detection (i.e., zero level).
External Interrupt 0 (INT0) Flag.
Set by hardware by a falling edge or zero level being applied to external interrupt pin INT0,
depending on bit IT0 state.
Cleared by hardware when the PC vectors to the interrupt service routine only if the interrupt
was transition activated. If level activated, the external requesting source controls the request flag,
rather than the on-chip hardware.
External Interrupt 0 (IE0) Trigger Type.
Set by software to specify edge-sensitive detection (i.e., 1-to-0 transition).
Cleared by software to specify level-sensitive detection (i.e., zero level).
Timer/Counters 0 and 1 Data Registers
Each timer consists of two 8-bit registers. These can be used as
independent registers or combined to be a single 16-bit register
depending on the timer mode configuration.
TH0 and TL0
Timer 0 high byte and low byte.
SFR Address = 8CH, 8AH, respectively.
TH1 and TL1
Timer 1 high byte and low byte.
SFR Address = 8DH, 8BH, respectively.
REV. E
–31–
ADuC812
TIMER/COUNTERS 0 AND 1 OPERATING MODES
Mode 2 (8-Bit Timer/Counter with Auto Reload)
The following paragraphs describe the operating modes for
Timer/Counters 0 and 1. Unless otherwise noted, it should be
assumed that these modes of operation are the same for Timer 0
as for Timer 1.
Mode 2 configures the timer register as an 8-bit counter (TL0)
with automatic reload, as shown in Figure 28. Overflow from TL0
not only sets TF0, but also reloads TL0 with the contents of TH0,
which is preset by software. The reload leaves TH0 unchanged.
Mode 0 (13-Bit Timer/Counter)
Mode 0 configures an 8-bit timer/counter with a divide-by-32
prescaler. Figure 26 shows Mode 0 operation.
CORE
CLK
12
C/T = 0
CORE
CLK
INTERRUPT
TL0
(8 BITS)
12
TF0
C/T = 1
C/T = 0
TL0
TH0
(5 BITS) (8 BITS)
P3.4/T0
INTERRUPT
CONTROL
TF0
TR0
C/T = 1
P3.4/T0
RELOAD
TH0
(8 BITS)
GATE
P3.2/INT0
CONTROL
TR0
Figure 28. Timer/Counter 0, Mode 2
GATE
P3.2/INT0
Mode 3 (Two 8-Bit Timer/Counters)
Figure 26. Timer/Counter 0, Mode 0
In this mode, the timer register is configured as a 13-bit register. As
the count rolls over from all 1s to all 0s, it sets the timer overflow
flag TF0. The overflow flag, TF0, can then be used to request
an interrupt. The counted input is enabled to the timer when
TR0 = 1 and either Gate = 0 or INT0 = 1. Setting Gate = 1 allows
the timer to be controlled by external input INT0 to facilitate
pulsewidth measurements. TR0 is a control bit in the special
function register TCON; Gate is in TMOD. The 13-bit register
consists of all eight bits of TH0 and the lower five bits of TL0.
The upper three bits of TL0 are indeterminate and should be
ignored. Setting the run flag (TR0) does not clear the registers.
Mode 3 has different effects on Timer 0 and Timer 1. Timer 1 in
Mode 3 simply holds its count. The effect is the same as setting
TR1 = 0. Timer 0 in Mode 3 establishes TL0 and TH0 as two
separate counters. This configuration is shown in Figure 29.
TL0 uses the Timer 0 control bits: C/T, Gate, TR0, INT0, and
TF0. TH0 is locked into a timer function (counting machine
cycles) and takes over the use of TR1 and TF1 from Timer 1.
Thus, TH0 now controls the Timer 1 interrupt. Mode 3 is
provided for applications requiring an extra 8-bit timer or counter.
When Timer 0 is in Mode 3, Timer 1 can be turned on and off by
switching it out of, and into, its own Mode 3, or can still be used
by the serial interface as a baud rate generator. In fact, it can be used
in any application not requiring an interrupt from Timer 1 itself.
Mode 1 (16-Bit Timer/Counter)
Mode 1 is the same as Mode 0, except that the timer register is
running with all 16 bits. Mode 1 is shown in Figure 27.
CORE
CLK
CORE
CLK/12
12
C/T = 0
CORE
CLK
TL0
(8 BITS)
12
INTERRUPT
TF0
C/T = 1
C/T = 0
TL0
TH0
(8 BITS) (8 BITS)
INTERRUPT
P3.4/T0
TR0
TF0
CONTROL
C/T = 1
P3.4/T0
GATE
CONTROL
P3.2/INT0
TR0
CORE
CLK/12
GATE
P3.2/INT0
TR1
Figure 27. Timer/Counter 0, Mode 1
TH0
(8 BITS)
TF1
INTERRUPT
CONTROL
Figure 29. Timer/Counter 0, Mode 3
–32–
REV. E
ADuC812
T2CON
Timer/Counter 2
Control Register
SFR Address
Power-On Default Value
Bit Addressable
C8H
00H
Yes
TF2
EXF2
RCLK
TCLK
EXEN2
TR2
CNT2
CAP2
Table XVII. T2CON SFR Bit Designations
Bit
Name
Description
7
TF2
6
EXF2
5
RCLK
4
TCLK
3
EXEN2
2
TR2
1
CNT2
0
CAP2
Timer 2 Overflow Flag.
Set by hardware on a Timer 2 overflow. TF2 will not be set when either RCLK = 1 or TCLK = 1.
Cleared by user software.
Timer 2 External Flag.
Set by hardware when either a capture or reload is caused by a negative transition on T2EX and
EXEN2 = 1.
Cleared by user software.
Receive Clock Enable Bit.
Set by user to enable the serial port to use Timer 2 overflow pulses for its receive clock in serial port
Modes 1 and 3.
Cleared by user to enable Timer 1 overflow to be used for the receive clock.
Transmit Clock Enable Bit.
Set by user to enable the serial port to use Timer 2 overflow pulses for its transmit clock in serial
port Modes 1 and 3.
Cleared by user to enable Timer 1 overflow to be used for the transmit clock.
Timer 2 External Enable Flag.
Set by user to enable a capture or reload to occur as a result of a negative transition on T2EX if
Timer 2 is not being used to clock the serial port.
Cleared by user for Timer 2 to ignore events at T2EX.
Timer 2 Start/Stop Control Bit.
Set by user to start Timer 2.
Cleared by user to stop Timer 2.
Timer 2 Timer or Counter Function Select Bit.
Set by the user to select counter function (input from external T2 pin).
Cleared by the user to select timer function (input from on-chip core clock).
Timer 2 Capture/Reload Select Bit.
Set by user to enable captures on negative transitions at T2EX if EXEN2 = 1.
Cleared by user to enable autoreloads with Timer 2 overflows or negative transitions at T2EX
when EXEN2 = 1. When either RCLK = 1 or TCLK = 1, this bit is ignored and the timer is
forced to autoreload on Timer 2 overflow.
Timer/Counter 2 Data Registers
Timer/Counter 2 also has two pairs of 8-bit data registers
associated with it. These are used as both timer data registers
and timer capture/reload registers.
TH2 and TL2
Timer 2, data high byte and low byte.
SFR Address = CDH, CCH, respectively.
RCAP2H and RCAP2L
Timer 2, Capture/Reload high byte and low byte.
SFR Address = CBH, CAH, respectively.
REV. E
–33–
ADuC812
Timer/Counter Operation Modes
16-Bit Capture Mode
The following paragraphs describe the operating modes for
Timer/Counter 2. The operating modes are selected by bits in the
T2CON SFR as shown in Table XVIII.
In the Capture mode, there are again two options, which are
selected by bit EXEN2 in T2CON. If EXEN2 = 0, then Timer 2
is a 16-bit timer or counter that, upon overflowing, sets bit TF2,
the Timer 2 overflow bit, that can be used to generate an interrupt. If EXEN2 = 1, then Timer 2 still performs the above, but
a l-to-0 transition on external input T2EX causes the current
value in the Timer 2 registers, TL2 and TH2, to be captured into
registers RCAP2L and RCAP2H, respectively. In addition, the
transition at T2EX causes bit EXF2 in T2CON to be set, and
EXF2, like TF2, can generate an interrupt. The Capture mode
is illustrated in Figure 31.
Table XVIII. TIMECON SFR Bit Designations
RCLK (or) TCLK
CAP2
TR2
MODE
0
0
1
X
0
1
X
X
1
1
1
0
16-Bit Autoreload
16-Bit Capture
Baud Rate
OFF
16-Bit Autoreload Mode
In Autoreload mode, there are two options, which are selected by
bit EXEN2 in T2CON. If EXEN2 = 0, then when Timer 2 rolls
over, it not only sets TF2 but also causes the Timer 2 registers to
reload with the 16-bit value in registers RCAP2L and RCAP2H,
which are preset by software. If EXEN2 = 1 then Timer 2 still
performs the above, but with the added feature that a 1-to-0
transition at external input T2EX will also trigger the 16-bit reload
and set EXF2. The Autoreload mode is illustrated in Figure 30.
CORE
CLK
12
The baud rate generator mode is selected by RCLK = 1 and/or
TCLK = 1.
In either case, if Timer 2 is being used to generate the baud rate,
the TF2 interrupt flag will not occur. Therefore Timer 2 interrupts will not occur, so they do not have to be disabled. In this
mode however, the EXF2 flag can still cause interrupts and this
can be used as a third external interrupt.
Baud rate generation will be described as part of the UART
serial port operation in the following pages.
C/T2 = 0
TL2
(8 BITS)
TH2
(8 BITS)
RCAP2L
RCAP2H
C/T2 = 1
T2
PIN
CONTROL
TR2
RELOAD
TRANSITION
DETECTOR
TF2
TIMER
INTERRUPT
T2EX
PIN
EXF2
CONTROL
EXEN2
Figure 30. Timer/Counter 2, 16-Bit Autoreload Mode
CORE
CLK
12
C/T2 = 0
TL2
(8 BITS)
TH2
(8 BITS)
TF2
C/T2 = 1
T2
PIN
CONTROL
TR2
TIMER
INTERRUPT
CAPTURE
TRANSITION
DETECTOR
RCAP2L
T2EX
PIN
RCAP2H
EXF2
CONTROL
EXEN2
Figure 31. Timer/Counter 2, 16-Bit Capture Mode
–34–
REV. E
ADuC812
UART SERIAL INTERFACE
The serial port is full-duplex, meaning it can transmit and receive
simultaneously. It is also receive-buffered, meaning it can begin
receiving a second byte before a previously received byte has been
read from the receive register. However, if the first byte still has
not been read by the time reception of the second byte is complete, the first byte will be lost. The physical interface to the
serial data network is via Pins RXD(P3.0) and TXD(P3.1)
SCON
UART Serial Port
Control Register
SFR Address
Power-On Default Value
Bit Addressable
98H
00H
Yes
SM0
SM1
SM2
while the SFR interface to the UART is comprised of SBUF
and SCON, as described below.
SBUF
The serial port receive and transmit registers are both accessed
through the SBUF SFR (SFR address = 99H). Writing to
SBUF loads the transmit register and reading SBUF accesses a
physically separate receive register.
REN
TB8
RB8
TI
RI
Table XIX. SCON SFR Bit Designations
Bit
Name
Description
7
6
SM0
SM1
5
SM2
4
REN
3
TB8
2
RB8
1
TI
0
RI
UART Serial Mode Select Bits.
These bits select the Serial Port operating mode as follows:
SM0
SM1
Selected Operating Mode
0
0
Mode 0: Shift Register, fixed baud rate (Core_Clk/2)
0
1
Mode 1: 8-bit UART, variable baud rate
1
0
Mode 2: 9-bit UART, fixed baud rate (Core_Clk/64) or (Core_Clk/32)
1
1
Mode 3: 9-bit UART, variable baud rate
Multiprocessor Communication Enable Bit.
Enables multiprocessor communication in Modes 2 and 3. In Mode 0, SM2 should be cleared.
In Mode 1, if SM2 is set, RI will not be activated if a valid stop bit was not received. If SM2 is
cleared, RI will be set as soon as the byte of data has been received. In Modes 2 or 3, if SM2 is
set, RI will not be activated if the received ninth data bit in RB8 is 0. If SM2 is cleared, RI will
be set as soon as the byte of data has been received.
Serial Port Receive Enable Bit.
Set by user software to enable serial port reception.
Cleared by user software to disable serial port reception.
Serial Port Transmit (Bit 9).
The data loaded into TB8 will be the ninth data bit that will be transmitted in Modes 2 and 3.
Serial Port Receiver Bit 9.
The ninth data bit received in Modes 2 and 3 is latched into RB8. For Mode 1, the stop bit is
latched into RB8.
Serial Port Transmit Interrupt Flag.
Set by hardware at the end of the eighth bit in Mode 0, or at the beginning of the stop bit in
Modes 1, 2, and 3. TI must be cleared by user software.
Serial Port Receive Interrupt Flag.
Set by hardware at the end of the eighth bit in Mode 0, or halfway through the stop bit in
Modes 1, 2, and 3. RI must be cleared by software.
REV. E
–35–
ADuC812
Mode 0 (8-Bit Shift Register Mode)
Mode 2 (9-Bit UART with Fixed Baud Rate)
Mode 0 is selected by clearing both the SM0 and SM1 bits in the
SFR SCON. Serial data enters and exits through RxD. TxD
outputs the shift clock. Eight data bits are transmitted or received.
Transmission is initiated by any instruction that writes to SBUF.
The data is shifted out of the RxD line. The eight bits are
transmitted with the least significant bit (LSB) first, as shown
in Figure 32.
Mode 2 is selected by setting SM0 and clearing SM1. In this
mode, the UART operates in 9-bit mode with a fixed baud rate.
The baud rate is fixed at Core_Clk/64 by default, although by
setting the SMOD bit in PCON, the frequency can be doubled to
Core_Clk/32. Eleven bits are transmitted or received, a start
bit (0), eight data bits, a programmable ninth bit, and a stop bit
(1). The ninth bit is most often used as a parity bit, although it
can be used for anything, including a ninth data bit if required.
MACHINE
CYCLE 1
MACHINE
CYCLE 2
MACHINE
CYCLE 7
S1 S2 S3 S4 S5 S6 S1 S2 S3 S4
MACHINE
CYCLE 8
To transmit, the eight data bits must be written into SBUF. The
ninth bit must be written to TB8 in SCON. When transmission is
initiated, the eight data bits (from SBUF) are loaded onto the
transmit shift register (LSB first). The contents of TB8 are loaded
into the ninth bit position of the transmit shift register. The transmission will start at the next valid baud rate clock. The TI flag
is set as soon as the stop bit appears on TxD.
S4 S5 S6 S1 S2 S3 S4 S5 S6
CORE
CLK
ALE
RxD
(DATA OUT)
DATA BIT 0
DATA BIT 1
DATA BIT 6
DATA BIT 7
TxD
(SHIFT
CLOCK)
Figure 32. UART Serial Port Transmission, Mode 0
Reception is initiated when the receive enable bit (REN) is 1 and
the receive interrupt bit (RI) is 0. When RI is cleared, the data
is clocked into the RxD line and the clock pulses are output
from the TxD line.
Mode 1 (8-Bit UART, Variable Baud Rate)
Mode 1 is selected by clearing SM0 and setting SM1. Each data
byte (LSB first) is preceded by a start bit (0) and followed by a
stop bit (1). Therefore 10 bits are transmitted on TxD or received
on RxD. The baud rate is set by the Timer 1 or Timer 2 overflow
rate, or a combination of the two (one for transmission and the
other for reception).
Transmission is initiated by writing to SBUF. The “write to SBUF”
signal also loads a 1 (stop bit) into the ninth bit position of the
transmit shift register. The data is output bit by bit until the stop
bit appears on TxD and the transmit interrupt flag (TI) is automatically set, as shown in Figure 33.
START
BIT
TxD
STOP BIT
D0
D1
D2
D3
D4
D5
D6
D7
TI
(SCON.1)
SET INTERRUPT
i.e., READY FOR MORE DATA
Figure 33. UART Serial Port Transmission, Mode 0
Reception is initiated when a 1-to-0 transition is detected on
RxD. Assuming a valid start bit was detected, character reception
continues. The start bit is skipped and the eight data bits are
clocked into the serial port shift register. When all eight bits have
been clocked in, the following events occur:
The eight bits in the receive shift register are latched into SBUF.
Reception for Mode 2 is similar to that of Mode 1. The eight
data bytes are input at RxD (LSB first) and loaded onto the
receive shift register. When all eight bits have been clocked in,
the following events occur:
The eight bits in the receive shift register are latched into SBUF.
The ninth data bit is latched into RB8 in SCON.
The Receiver interrupt flag (RI) is set.
This will be the case if, and only if, the following conditions are
met at the time the final shift pulse is generated:
RI = 0, and
Either SM2 = 0, or SM2 = 1 and the received stop bit = 1.
If either of these conditions is not met, the received frame is
irretrievably lost, and RI is not set.
Mode 3 (9-Bit UART with Variable Baud Rate)
Mode 3 is selected by setting both SM0 and SM1. In this mode
the 8051 UART serial port operates in 9-bit mode with a variable
baud rate determined by either Timer 1 or Timer 2. The operation of the 9-bit UART is the same as for Mode 2, but the baud
rate can be varied as for Mode 1.
In all four modes, transmission is initiated by any instruction
that uses SBUF as a destination register. Reception is initiated in
Mode 0 by the condition RI = 0 and REN = 1. Reception is
initiated in the other modes by the incoming start bit if REN = 1.
UART Serial Port Baud Rate Generation
Mode 0 Baud Rate Generation
The baud rate in Mode 0 is fixed:
Mode 0 Baud Rate = (Core Clock Frequency 12)
Mode 2 Baud Rate Generation
The baud rate in Mode 2 depends on the value of the SMOD bit
in the PCON SFR. If SMOD = 0, the baud rate is 1/64 of the core
clock. If SMOD = 1, the baud rate is 1/32 of the core clock:
(
The Receiver interrupt flag (RI) is set.
This will be the case if, and only if, the following conditions are
met at the time the final shift pulse is generated:
RI = 0, and
)
Mode 2 Baud Rate = 2SMOD 64 × (Core Clock Frequency)
The ninth bit (Stop bit) is clocked into RB8 in SCON.
Mode 1 and 3 Baud Rate Generation
The baud rates in Modes 1 and 3 are determined by the overflow
rate in Timer 1 or Timer 2, or both (one for transmit and the
other for receive).
Either SM2 = 0 or SM2 = 1 and the received stop bit = 1.
If either of these conditions is not met, the received frame is
irretrievably lost, and RI is not set.
–36–
REV. E
ADuC812
Timer 1 Generated Baud Rates
Modes 1 and 3 Baud Rate =
When Timer 1 is used as the baud rate generator, the baud rates
in Modes 1 and 3 are determined by the Timer 1 overflow rate and
the value of SMOD as follows:
(1 16) × (Timer 2 Overflow Rate)
Therefore, when Timer 2 is used to generate baud rates, the
timer increments every two clock cycles and not every core
machine cycle as before. Therefore, it increments six times
faster than Timer 1, and baud rates six times faster are possible.
Because Timer 2 has 16-bit autoreload capability, very low baud
rates are still possible.
Modes 1 and 3 Baud Rate =
(2
)
32 × (Timer 1 Overflow Rate)
SMOD
The Timer 1 interrupt should be disabled in this application.
The timer itself can be configured for either timer or counter
operation, and in any of its three running modes. In the most
typical application, it is configured for timer operation in the
Autoreload mode (high nibble of TMOD = 0010 binary). In that
case, the baud rate is given by the formula:
Modes 1 and 3 Baud Rate =
(2
SMOD
) (
(
32 × Core Clock 12 × [256 − TH 1]
Timer 2 is selected as the baud rate generator by setting the TCLK
and/or RCLK in T2CON. The baud rates for transmit and receive
can be simultaneously different. Setting RCLK and/or TCLK puts
Timer 2 into its baud rate generator mode as shown in Figure 34.
In this case, the baud rate is given by the formula:
Modes 1 and 3 Baud Rate =
))
(Core Clk)
Table XX shows some commonly used baud rates and how they
might be calculated from a core clock frequency of 11.0592 MHz
and 12 MHz. Generally speaking, a 5% error is tolerable using
asynchronous (start/stop) communications.
( 32 × [65536 − (RCAP 2H , RCAP 2L)])
Table XXI shows some commonly used baud rates and how they
might be calculated from a core clock frequency of 11.0592 MHz
and 12 MHz.
Table XXI. Commonly Used Baud Rates, Timer 2
Table XX. Commonly Used Baud Rates, Timer 1
Ideal
Baud
Core
CLK
SMOD
Value
TH1-Reload
Value
Actual
Baud
%
Error
9600
19200
9600
2400
12
11.0592
11.0592
11.0592
1
1
0
0
–7 (F9H)
–3 (FDH)
–3 (FDH)
–12 (F4H)
8929
19200
9600
2400
7
0
0
0
Timer 2 Generated Baud Rates
Baud rates can also be generated using Timer 2. Using Timer 2 is
similar to using Timer 1 in that the timer must overflow 16 times
before a bit is transmitted/received. Because Timer 2 has a 16-bit
Autoreload mode, a wider range of baud rates is possible using
Timer 2.
Ideal
Baud
Core
CLK
RCAP2H
Value
RCAP2L
Value
Actual
Baud
%
Error
19200
9600
2400
1200
19200
9600
2400
1200
12
12
12
12
11.0592
11.0592
11.0592
11.0592
–1 (FFH)
–1 (FFH)
–1 (FFH)
–2 (FEH)
–1 (FFH)
–1 (FFH)
–1 (FFH)
–2 (FFH)
–20 (ECH)
–41 (D7H)
–164 (5CH)
–72 (B8H)
–18 (EEH)
–36 (DCH)
–144 (70H)
–32 (E0H)
19661
9591
2398
1199
19200
9600
2400
1200
2.4
0.1
0.1
0.1
0
0
0
0
TIMER 1
OVERFLOW
NOTE: OSCILLATOR FREQUENCY
IS DIVIDED BY 2, NOT 12.
2
0
CORE
CLK
2
SMOD
C/T2 = 0
TL2
(8 BITS)
T2
PIN
1
CONTROL
TH2
(8 BITS)
TIMER 2
OVERFLOW
1
0
RCLK
C/T2 = 1
16
1
TR2
TCLK
RELOAD
16
RCAP2L
NOTE: AVAILABILITY OF ADDITIONAL
EXTERNAL INTERRUPT
EXF
2
T2EX
PIN
TRANSITION
DETECTOR
RCAP2H
TIMER 2
INTERRUPT
CONTROL
EXEN2
Figure 34. Timer 2, UART Baud Rates
REV. E
RX
CLOCK
0
–37–
TX
CLOCK
ADuC812
INTERRUPT SYSTEM
The ADuC812 provides a total of nine interrupt sources with two priority levels. The control and configuration of the interrupt system
is carried out through three interrupt related SFRs.
IE
IP
IE2
Interrupt Enable Register
Interrupt Priority Register
Secondary Interrupt Enable Register
IE
Interrupt Enable
Register
SFR Address
Power-On Default Value
Bit Addressable
A8H
00H
Yes
EA
EADC
ET2
ES
ET1
EX1
ET0
EX0
Table XXII. IE SFR Bit Designations
Bit
Name
Description
7
6
5
4
3
2
1
0
EA
EADC
ET2
ES
ET1
EX1
ET0
EX0
Written by user to enable “1” or disable “0” all interrupt sources.
Written by user to enable “1” or disable “0” ADC interrupt.
Written by user to enable “1” or disable “0” Timer 2 interrupt.
Written by user to enable “1” or disable “0” UART serial port interrupt.
Written by user to enable “1” or disable “0” Timer 1 interrupt.
Written by user to enable “1” or disable “0” External Interrupt 1.
Written by user to enable “1” or disable “0” Timer 0 interrupt.
Written by user to enable “1” or disable “0” External Interrupt 0.
IP
Interrupt Priority
Register
SFR Address
Power-On Default Value
Bit Addressable
B8H
00H
Yes
PSI
PADC
PT2
PS
PT1
PX1
PT0
PX0
Table XXIII. IP SFR Bit Designations
Bit
Name
Description
7
6
5
4
3
2
1
0
PSI
PADC
PT2
PS
PT1
PX1
PT0
PX0
Written by user to select I2C/SPI priority (“1” = High; “0” = Low).
Written by user to select ADC interrupt priority (“1” = High; “0” = Low).
Written by user to select Timer 2 interrupt priority (“1” = High; “0” = Low).
Written by user to select UART serial port interrupt priority (“1” = High; “0” = Low).
Written by user to select Timer 1 interrupt priority (“1” = High; “0” = Low).
Written by user to select External Interrupt 1 priority (“1” = High; “0” = Low).
Written by user to select Timer 0 interrupt priority (“1” = High; “0” = Low).
Written by user to select External Interrupt 0 priority (“1” = High; “0” = Low).
–38–
REV. E
ADuC812
IE2
Secondary Interrupt
Enable Register
SFR Address
Power-On Default Value
Bit Addressable
A9H
00H
No
—
—
—
—
—
—
EPSMI
ESI
Table XXIV. IE2 SFR Bit Designations
Bit
Name
Description
7
6
5
4
3
2
1
0
—
—
—
—
—
—
EPSMI
ESI
Reserved for future use.
Reserved for future use.
Reserved for future use.
Reserved for future use.
Reserved for future use.
Reserved for future use.
Written by user to Enable “1” or Disable “0” power supply monitor interrupt.
Written by user to Enable “1” or Disable “0” I2C/SPI serial port interrupt.
Interrupt Priority
Interrupt Vectors
The Interrupt Enable registers are written by the user to enable
individual interrupt sources, while the Interrupt Priority registers
allow the user to select one of two priority levels for each interrupt.
An interrupt of high priority may interrupt the service routine of
a low priority interrupt. If two interrupts of different priorities
occur at the same time, the higher level interrupt will be served
first. An interrupt cannot be interrupted by another interrupt of
the same priority level. If two interrupts of the same priority level
occur simultaneously, a polling sequence is observed, as shown
in Table XXV.
When an interrupt occurs, the program counter is pushed onto
the stack and the corresponding interrupt vector address is
loaded into the program counter. The interrupt vector addresses
are shown in the Table XXVI.
Table XXVI. Interrupt Vector Addresses
Table XXV. Priority within an Interrupt Level
Source
Priority
Description
PSMI
IE0
ADCI
TF0
IE1
TF1
I2CI + ISPI
RI + TI
TF2 + EXF2
1 (Highest)
2
3
4
5
6
7
8
9 (Lowest)
Power Supply Monitor Interrupt
External Interrupt 0
ADC Interrupt
Timer/Counter 0 Interrupt
External Interrupt 1
Timer/Counter 1 Interrupt
I2C/SPI Interrupt
Serial Interrupt
Timer/Counter 2 Interrupt
REV. E
–39–
Source
Vector Address
IE0
TF0
IE1
TF1
RI + TI
TF2 + EXF2
ADCI
I2CI + ISPI
PSMI
0003H
000BH
0013H
001BH
0023H
002BH
0033H
003BH
0043H
ADuC812
ADuC812 HARDWARE DESIGN CONSIDERATIONS
This section outlines some of the key hardware design considerations that must be addressed when integrating the ADuC812
into any hardware system.
Clock Oscillator
The clock source for the ADuC812 can come either from an
external source or from the internal clock oscillator. To use the
internal clock oscillator, connect a parallel resonant crystal
between Pins 32 and 33, and connect a capacitor from each pin
to ground as shown below.
External program memory (if used) must be connected to the
ADuC812 as illustrated in Figure 37. Note that 16 I/O lines
(Ports 0 and 2) are dedicated to bus functions during external
program memory fetches. Port 0 (P0) serves as a multiplexed
address/data bus. It emits the low byte of the program counter
(PCL) as an address, and then goes into a float state awaiting
the arrival of the code byte from the program memory. During
the time that the low byte of the program counter is valid on P0,
the signal ALE (Address Latch Enable) clocks this byte into an
address latch. Meanwhile, Port 2 (P2) emits the high byte of the
program counter (PCH), then PSEN strobes the EPROM and
the code byte is read into the ADuC812.
ADuC812
XTAL1
ADuC812
EPROM
D0–D7
(INSTRUCTION)
P0
XTAL2
TO INTERNAL
TIMING CIRCUITS
A0–A7
LATCH
ALE
Figure 35. External Parallel Resonant Crystal Connections
A8–A15
P2
ADuC812
EXTERNAL
CLOCK
SOURCE
PSEN
OE
XTAL1
Figure 37. External Program Memory Interface
XTAL2
TO INTERNAL
TIMING CIRCUITS
Figure 36. Connecting an External Clock Source
Whether using the internal oscillator or an external clock source,
the ADuC812’s specified operational clock speed range is 300 kHz
to 16 MHz. The core is static, and will function all the way
down to dc. But at clock speeds slower that 400 kHz the ADC
will no longer function correctly. Therefore, to ensure specified
operation, use a clock frequency of at least 400 kHz and no
more than 16 MHz.
External Memory Interface
Note that program memory addresses are always 16 bits wide, even
in cases where the actual amount of program memory used is less
than 64 K bytes. External program execution sacrifices two of the
8-bit ports (P0 and P2) to the function of addressing the program
memory. While executing from external program memory, Ports 0
and 2 can be used simultaneously for read/write access to external
data memory, but not for general-purpose I/O.
Though both external program memory and external data memory
are accessed by some of the same pins, the two are completely
independent of each other from a software point of view. For example,
the chip can read/write external data memory while executing
from external program memory.
Figure 38 shows a hardware configuration for accessing up to
64 K bytes of external RAM. This interface is standard to any
8051 compatible MCU.
In addition to its internal program and data memories, the
ADuC812 can access up to 64 K bytes of external program
memory (ROM, PROM, etc.) and up to 16 M bytes of external data memory (SRAM).
To select from which code space (internal or external program
memory) to begin executing instructions, tie the EA (external
access) pin high or low, respectively. When EA is high (pulled
up to VDD), user program execution will start at address 0 of the
internal 8 K bytes Flash/EE code space. When EA is low (tied
to ground) user program execution will start at address 0 of the
external code space. In either case, addresses above 1FFFH
(8K) are mapped to the external space.
Note that a second very important function of the EA pin is
described in the Single Pin Emulation Mode section.
ADuC812
SRAM
D0–D7
(DATA)
P0
LATCH
A0–A7
ALE
P2
A8–A15
RD
OE
WR
WE
Figure 38. External Data Memory Interface
(64K Address Space)
–40–
REV. E
ADuC812
If access to more than 64K bytes of RAM is desired, a feature
unique to the ADuC812 allows addressing up to 16 MBytes
of external RAM simply by adding an additional latch as illustrated in Figure 39.
ADuC812
SRAM
The best way to implement an external POR function to meet the
above requirements involves the use of a dedicated POR chip, such
as the ADM809/ADM810 SOT-23 packaged PORs from Analog
Devices. Recommended connection diagrams for both active high
ADM810 and active low ADM809 PORs are shown in Figure 41
and Figure 42, respectively.
D0–D7
(DATA)
P0
LATCH
ADuC812
POWER SUPPLY
20
A0–A7
34
ALE
DVDD
48
A8–A15
P2
POR
(ACTIVE HIGH)
LATCH
15
RESET
A16–A23
RD
OE
WR
WE
Figure 41. External Active High POR Circuit
Figure 39. External Data Memory Interface (16 M Bytes
Address Space)
Some active-low POR chips, such as the ADM809, can be used
with a manual push-button as an additional reset source as
illustrated by the dashed line connection in Figure 42.
Detailed timing diagrams of external program and data memory
read and write access can be found in the Timing Specification sections.
Power-On Reset Operation
External POR (power-on reset) circuitry must be implemented to
drive the RESET pin of the ADuC812. The circuit must hold
the RESET pin asserted (high) whenever the power supply
(DVDD) is below 2.5 V. Furthermore, VDD must remain above
2.5 V for at least 10 ms before the RESET signal is deasserted
(low), by which time the power supply must have reached at least
a 2.7 V level. The external POR circuit must be operational
down to 1.2 V or less. The timing diagram in Figure 40 illustrates this functionality under three separate events: power-up,
brownout, and power-down. Notice that when RESET is asserted
(high), it tracks the voltage on DVDD. These recommendations
must be adhered to through the manufacturing flow of your
ADuC812 based system as well as during its normal power-on
operation. Failure to adhere to these recommendations can
result in permanent damage to device functionality.
ADuC812
POWER SUPPLY
In either implementation, Port 0 (P0) serves as a multiplexed
address/data bus. It emits the low byte of the data pointer (DPL) as
an address, which is latched by a pulse of ALE prior to data being
placed on the bus by the ADuC812 (write operation) or the
SRAM (read operation). Port 2 (P2) provides the data pointer
page byte (DPP) to be latched by ALE, followed by the data
pointer high byte (DPH). If no latch is connected to P2, DPP is
ignored by the SRAM and the 8051 standard of 64K byte external
data memory access is maintained.
20
1k
34
POR
(ACTIVE LOW)
15
RESET
OPTIONAL
MANUAL
RESET
PUSH BUTTON
Figure 42. External Active Low POR Circuit
Power Supplies
The ADuC812’s operational power supply voltage range is 2.7 V
to 5.25 V. Although the guaranteed data sheet specifications are
given only for power supplies within 2.7 V to 3.6 V or ±10% of
the nominal 5 V level, the chip will function equally well at any
power supply level between 2.7 V and 5.5 V.
Separate analog and digital power supply pins (AVDD and DVDD,
respectively) allow AVDD to be kept relatively free of noisy digital
signals often present on the system DVDD line. However, though
you can power AVDD and DVDD from two separate supplies if
desired, you must ensure that they remain within ±0.3 V of one
another at all times in order to avoid damaging the chip (as per the
Absolute Maximum Ratings section). Therefore it is recommended
that unless AVDD and DVDD are connected directly together,
you connect back-to-back Schottky diodes between them as
shown in Figure 43.
DIGITAL SUPPLY
+
–
2.5V MIN
ANALOG SUPPLY
10F
10F
ADuC812
DVDD
1.2V MAX
DVDD
48
10ms
MIN
10ms
MIN
1.2V MAX
+
–
20
34
DVDD
AVDD 5
DGND
AGND 6
0.1F
48
0.1F
21
RESET
35
47
Figure 40. External POR Timing
Figure 43. External Dual-Supply Connections
REV. E
–41–
ADuC812
As an alternative to providing two separate power supplies, the
user can help keep AV DD quiet by placing a small series resistor
and/or ferrite bead between it and DVDD, and then decoupling
AVDD separately to ground. An example of this configuration is
shown in Figure 44. With this configuration, other analog
circuitry (such as op amps, voltage reference, and so on) can be
powered from the AVDD supply line as well. The user will still
want to include back-to-back Schottky diodes between AVDD
and DVDD in order to protect from power-up and power-down
transient conditions that could separate the two supply voltages
momentarily.
Table XXVII. Typical IDD of Core and Peripherals
VDD = 5 V
CORE
(Normal Mode) (1.6 nAs × MCLK) +
6 mA
CORE
(Idle Mode)
(0.75 nAs × MCLK) +
5 mA
ADC
1.3 mA
DAC (Each)
250 µA
Voltage Ref
200 µA
DIGITAL SUPPLY
+
–
10F
BEAD
1.6
ADuC812
AVDD 5
0.1F
48
0.1F
21
35 DGND
47
(0.8 nAs × MCLK) +
3 mA
(0.25 nAs × MCLK) +
3 mA
1.0 mA
200 µA
150 µA
Since operating DVDD current is primarily a function of clock
speed, the expressions for CORE supply current in Table XXVII
are given as functions of MCLK, the oscillator frequency. Plug
in a value for MCLK in hertz to determine the current consumed
by the core at that oscillator frequency. Since the ADC and DACs
can be enabled or disabled in software, add only the currents
from the peripherals you expect to use. The internal voltage reference is automatically enabled whenever either the ADC or at
least one DAC is enabled. And again, do not forget to include
current sourced by I/O pins, serial port pins, DAC outputs, and
so forth, plus the additional current drawn during Flash/EE
erase and program cycles.
10F
20
34 DVDD
VDD = 3 V
AGND 6
Figure 44. External Single-Supply Connections
Notice that in both Figure 43 and Figure 44, a large value (10 µF)
reservoir capacitor sits on DVDD and a separate 10 µF capacitor
sits on AVDD. Also, local small value (0.1 µF) capacitors are
located at each VDD pin of the chip. As per standard design practice, be sure to include all of these capacitors, and ensure the
smaller capacitors are close to each AVDD pin with trace lengths as
short as possible. Connect the ground terminal of each of these
capacitors directly to the underlying ground plane. Finally, it
should also be noted that, at all times, the analog and digital
ground pins on the ADuC812 must be referenced to the same
system ground reference point.
A software switch allows the chip to be switched from normal
mode into idle mode, and also into full power-down mode.
Below are brief descriptions of power-down and idle modes.
In idle mode, the oscillator continues to run but is gated off to
the core only. The on-chip peripherals continue to receive the
clock, and remain functional. Port pins and DAC output pins
retain their states in this mode. The chip will recover from idle
mode upon receiving any enabled interrupt, or upon receiving a
hardware reset.
Power Consumption
The currents consumed by the various sections of the ADuC812
are shown in Table XXVII. The CORE values given represent
the current drawn by DVDD, while the rest (ADC, DAC, Voltage Reference) are pulled by the AVDD pin and can be disabled
in software when not in use. The other on-chip peripherals
(watchdog timer, power supply monitor, and so on) consume
negligible current and are therefore lumped in with the CORE
operating current here. Of course, the user must add any
currents sourced by the DAC or the parallel and serial I/O pins,
in order to determine the total current needed at the ADuC812’s
supply pins. Also, current drawn from the DVDD supply will
increase by approximately 10 mA during Flash/EE erase and
program cycles.
In full power-down mode, the on-chip oscillator stops, and all
on-chip peripherals are shut down. Port pins retain their logic levels
in this mode, but the DAC output goes to a high impedance
state (three-state). The chip will only recover from power-down
mode upon receiving a hardware reset or when power is cycled.
During full power-down mode, the ADuC812 consumes a total
of approximately 5 µA.
–42–
REV. E
ADuC812
In all of these scenarios, and in more complicated real-life applications, keep in mind the flow of current from the supplies and
back to ground. Make sure the return paths for all currents are
as close as possible to the paths the currents took to reach their
destinations. For example, do not power components on the
analog side of Figure 45b with DVDD since that would force
return currents from DVDD to flow through AGND. Also, try to
avoid digital currents flowing under analog circuitry, which could
happen if the user placed a noisy digital chip on the left half of the
board in Figure 45c. Whenever possible, avoid large discontinuities
in the ground plane(s) (formed by a long trace on the same
layer), since they force return signals to travel a longer path. And
of course, make all connections to the ground plane directly,
with little or no trace separating the pin from its via to ground.
Grounding and Board Layout Recommendations
As with all high resolution data converters, special attention
must be paid to grounding and PC board layout of ADuC812
based designs in order to achieve optimum performance from
the ADC and DACs.
Although the ADuC812 has separate pins for analog and digital
ground (AGND and DGND), the user must not tie these to two
separate ground planes unless the two ground planes are connected
together very close to the ADuC812, as illustrated in the simplified example of Figure 45a. In systems where digital and analog
ground planes are connected together somewhere else (for example,
at the system’s power supply), they cannot be connected again
near the ADuC812 since a ground loop would result. In these
cases, tie the ADuC812’s AGND and DGND pins all to the
analog ground plane, as illustrated in Figure 45b. In systems with
only one ground plane, ensure that the digital and analog components are physically separated onto separate halves of the board
such that digital return currents do not flow near analog circuitry
and vice versa. The ADuC812 can then be placed between the
digital and analog sections, as illustrated in Figure 45c.
a.
If the user plans to connect fast logic signals (rise/fall time < 5 ns)
to any of the ADuC812’s digital inputs, add a series resistor to
each relevant line to keep rise and fall times longer than 5 ns at the
ADuC812 input pins. A value of 100 or 200 is usually sufficient to prevent high speed signals from coupling capacitively
into the ADuC812 and affecting the accuracy of ADC conversions.
PLACE ANALOG
COMPONENTS
HERE
PLACE DIGITAL
COMPONENTS
HERE
AGND
b.
DGND
PLACE ANALOG
COMPONENTS
HERE
PLACE DIGITAL
COMPONENTS
HERE
AGND
c.
DGND
PLACE DIGITAL
COMPONENTS
HERE
PLACE ANALOG
COMPONENTS
HERE
GND
Figure 45. System Grounding Schemes
REV. E
–43–
ADuC812
DOWNLOAD/DEBUG
ENABLE JUMPER
(NORMALLY OPEN)
DVDD
DVDD
1k
49
48
47
46
45
44 43
42
41
40
EA
50
PSEN
51
ADC0
DVDD
52
51
ANALOG INPUT
DGND
1k
2-PIN HEADER FOR
EMULATION ACCESS
(NORMALLY OPEN)
39
38
37
AVDD
36
AVDD
AGND
VREF OUTPUT
DVDD
DGND 35
DVDD 34
ADuC812
CREF
XTAL2 33
VREF
XTAL1 32
DAC0
31
DAC1
30
11.0592MHz
29
DGND
DVDD
TxD
RxD
ADC7
DVDD
RESET
DAC OUTPUT
28
27
ADM810
VCC
NOT CONNECTED IN THIS EXAMPLE
RST
DVDD
GND
ADM202
C1+
DVDD
9-PIN D-SUB
FEMALE
VCC
GND
V+
1
C1–
T1OUT
2
C2+
R1IN
3
C2–
R1OUT
4
V–
T1IN
5
T2OUT
T2IN
6
R2OUT
7
R2IN
8
9
Figure 46. Typical System Configuration
OTHER HARDWARE CONSIDERATIONS
To facilitate in-circuit programming, plus in-circuit debug and
emulation options, users will want to implement some simple
connection points in their hardware that will allow easy access
to download, debug, and emulation modes.
In-Circuit Serial Download Access
Nearly all ADuC812 designs will want to take advantage of the
in-circuit reprogrammability of the chip. This is accomplished by
a connection to the ADuC812’s UART, which requires an external
RS-232 chip for level translation if downloading code from a PC.
Basic configuration of an RS-232 connection is illustrated in
Figure 46 with a simple ADM202 based circuit. If users would
rather not design an RS-232 chip onto a board, refer to the Application Note, uC006–A 4-Wire UART-to-PC Interface, (available
at www.analog.com/microconverter) for a simple (and zero-costper-board) method of gaining in-circuit serial download access
to the ADuC812.
In addition to the basic UART connections, users will also need
a way to trigger the chip into download mode. This is accomplished via a 1 k pull-down resistor that can be jumpered onto
the PSEN pin, as shown in Figure 46. To get the ADuC812
into download mode, simply connect this jumper and powercycle the device (or manually reset the device, if a manual reset
button is available) and it will be ready to receive a new program
serially. With the jumper removed, the device will come up in
normal mode (and run the program) whenever power is cycled
or RESET is toggled.
Note that PSEN is normally an output (as described in the External
Memory Interface section), and is sampled as an input only on
the falling edge of RESET (i.e., at power-up or upon an external
manual reset). Note also that if any external circuitry unintentionally pulls PSEN low during power-up or reset events, it could
cause the chip to enter download mode and therefore fail to begin
user code execution as it should. To prevent this, ensure that no
external signals are capable of pulling the PSEN pin low, except
for the external PSEN jumper itself.
Embedded Serial Port Debugger
From a hardware perspective, entry to serial port debug mode is
identical to the serial download entry sequence described above.
In fact, both serial download and serial port debug modes can be
thought of as essentially one mode of operation used in two
different ways.
–44–
REV. E
ADuC812
Note that the serial port debugger is fully contained on the
ADuC812 device, (unlike ROM monitor type debuggers) and
therefore no external memory is needed to enable in-system
debug sessions.
Single-Pin Emulation Mode
Also built into the ADuC812 is a dedicated controller for single-pin
in-circuit emulation (ICE) using standard production ADuC812
devices. In this mode, emulation access is gained by connection
to a single pin, the EA pin. Normally, this pin is hardwired either
high or low to select execution from internal or external program
memory space, as described earlier. To enable single-pin emulation
mode, however, users will need to pull the EA pin high through
a 1 k resistor, as shown in Figure 46. The emulator will then
connect to the 2-pin header also shown in Figure 46. To be compatible with the standard connector that comes with the single-pin
emulator available from Accutron Limited (www.accutron.com),
use a 2-pin 0.1 inch pitch “Friction Lock” header from Molex
(www.molex.com) such as their part number 22-27-2021. Be sure
to observe the polarity of this header. As represented in Figure 46,
when the Friction Lock tab is at the right, the ground pin should
be the lower of the two pins (when viewed from the top).
Figure 47. Components of the QuickStart Development
System
Enhanced-Hooks Emulation Mode
ADuC812 also supports enhanced-hooks emulation mode. An
enhanced-hooks based emulator is available from Metalink
Corporation (www.metaice.com). No special hardware support
for these emulators needs to be designed onto the board since
these are pod-style emulators where users must replace the chip
on their board with a header device that the emulator pod plugs
into. The only hardware concern is then one of determining if
adequate space is available for the emulator pod to fit into the
system enclosure.
Typical System Configuration
A typical ADuC812 configuration is shown in Figure 46. It summarizes some of the hardware considerations discussed in the
previous paragraphs.
Figure 48. Typical Debug Session
Download—In-Circuit Serial Downloader
The QuickStart Development System is a full featured, low cost
development tool suite supporting the ADuC812. The system
consists of the following PC based (Windows® compatible)
hardware and software development tools.
The Serial Downloader is a Windows application that allows the
user to serially download an assembled program (Intel Hex format
file) to the on-chip program FLASH memory via the serial COM1
port on a standard PC. Application Note uC004 detailing this
serial download protocol is available at www.analog.com/
microconverter.
Hardware:
ADuC812 Evaluation Board, Plug-In
Power Supply and Serial Port Cable
DeBug—In-Circuit Debugger
Code Development:
8051 Assembler
Code Functionality:
Windows Based Simulator
QUICKSTART DEVELOPMENT SYSTEM
In-Circuit Code Download: Serial Downloader
In-Circuit Debugger:
Serial Port Debugger
Miscellaneous Other:
CD-ROM Documentation and
Two Additional Prototype Devices
Figure 47 shows the typical components of a QuickStart
Development System. A brief description of some of the software
tools components in the QuickStart Development System is
given in the following sections.
The Debugger is a Windows application that allows the user to
debug code execution on silicon using the MicroConverter UART
serial port. The debugger provides access to all on-chip peripherals during a typical debug session as well as single-step and
breakpoint code execution control.
ADSIM—Windows Simulator
The Simulator is a Windows application that fully simulates all
the MicroConverter functionality including ADC and DAC
peripherals. The simulator provides an easy-to-use, intuitive interface to the MicroConverter functionality and integrates many
standard debug features including multiple breakpoints, single
stepping, and code execution trace capability. This tool can be
used both as a tutorial guide to the part as well as an efficient way
to prove code functionality before moving to a hardware platform.
The QuickStart development tool suite software is freely available at
the Analog Devices MicroConverter website, www.analog.com/
microconverter.
REV. E
–45–
ADuC812
TIMING SPECIFICATIONS1, 2, 3 (AV
DD
= DVDD = 3.0 V or 5.0 V 10%. All specifications TA = TMIN to TMAX, unless otherwise noted.)
Parameter
Min
CLOCK INPUT (External Clock Driven XTAL1)
XTAL1 Period
tCK
tCKL
XTAL1 Width Low
XTAL1 Width High
tCKH
XTAL1 Rise Time
tCKR
tCKF
XTAL1 Fall Time
tCYC4
ADuC812 Machine Cycle Time
12 MHz
Typ
Max
83.33
Variable Clock
Min
Typ
Max
62.5
20
20
20
20
Unit
1000
20
20
20
20
1
12tCK
ns
ns
ns
ns
ns
µs
NOTES
1
AC inputs during testing are driven at DV DD – 0.5 V for a Logic 1 and 0.45 V for a Logic 0. Timing measurements are made at V IH min for a Logic 1 and V IL max for
a Logic 0.
2
For timing purposes, a port pin is no longer floating when a 100 mV change from load voltage occurs. A port pin begins to float when a 100 mV change from the
loaded VOH/VOL level occurs.
3
CLOAD for Port 0, ALE, PSEN outputs = 100 pF; C LOAD for all other outputs = 80 pF, unless otherwise noted.
4
ADuC812 Machine Cycle Time is nominally defined as MCLKIN/12.
tCKR
tCKH
tCKL
tCKF
tCK
Figure 49. XTAL 1 Input
DVDD – 0.5V
0.45V
0.2VCC + 0.9V
TEST POINTS
0.2VCC – 0.1V
VLOAD – 0.1V
VLOAD
VLOAD + 0.1V
TIMING
REFERENCE
POINTS
VLOAD – 0.1V
VLOAD
VLOAD – 0.1V
Figure 50. Timing Waveform Characteristics
–46–
REV. E
ADuC812
Parameter
EXTERNAL PROGRAM MEMORY READ CYCLE
ALE Pulsewidth
tLHLL
tAVLL
Address Valid to ALE Low
Address Hold after ALE Low
tLLAX
ALE Low to Valid Instruction In
tLLIV
tLLPL
ALE Low to PSEN Low
PSEN Pulsewidth
tPLPH
PSEN Low to Valid Instruction In
tPLIV
tPXIX
Input Instruction Hold after PSEN
Input Instruction Float after PSEN
tPXIZ
Address to Valid Instruction In
tAVIV
tPLAZ
PSEN Low to Address Float
tPHAX
Address Hold after PSEN High
12 MHz
Min
Max
Variable Clock
Min
Max
127
43
53
2tCK – 40
tCK – 40
tCK – 30
234
4tCK – 100
53
205
tCK – 30
3tCK – 45
145
3tCK – 105
0
0
59
312
25
tCK – 25
5tCK – 105
25
0
0
MCLK
tLHLL
ALE (O)
tAVLL
tLLPL
tPLPH
tLLIV
tPLIV
PSEN (O)
PORT 0 (I/O)
tPXIZ
tPLAZ
tLLAX
tPXIX
INSTRUCTION
(IN)
PCL (OUT)
tAVIV
tPHAX
PORT 2 (O)
PCH
Figure 51. External Program Memory Read Cycle
REV. E
–47–
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ADuC812
Parameter
EXTERNAL DATA MEMORY READ CYCLE
tRLRH
RD Pulsewidth
Address Valid after ALE Low
tAVLL
Address Hold after ALE Low
tLLAX
RD Low to Valid Data In
tRLDV
tRHDX
Data and Address Hold after RD
Data Float after RD
tRHDZ
ALE Low to Valid Data In
tLLDV
tAVDV
Address to Valid Data In
ALE Low to RD or WR Low
tLLWL
Address Valid to RD or WR Low
tAVWL
tRLAZ
RD Low to Address Float
tWHLH
RD or WR High to ALE High
12 MHz
Min
Max
Min
Variable Clock
Max
400
43
48
6tCK – 100
tCK – 40
tCK – 35
252
5tCK – 165
0
0
97
517
585
300
200
203
3tCK – 50
4tCK – 130
0
123
43
2tCK – 70
8tCK – 150
9tCK – 165
3tCK + 50
0
6tCK – 100
tCK – 40
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
MCLK
ALE (O)
tWHLH
PSEN (O)
tLLDV
tLLWL
tRLRH
RD (O)
tAVWL
tRLDV
tAVLL
tRHDZ
tLLAX
tRHDX
tRLAZ
PORT 0 (I/O)
A0–A7 (OUT)
DATA (IN)
tAVDV
PORT 2 (O)
A16–A23
A8–A15
Figure 52. External Data Memory Read Cycle
–48–
REV. E
ADuC812
Parameter
12 MHz
Min
Max
Variable Clock
Min
Max
Unit
EXTERNAL DATA MEMORY WRITE CYCLE
WR Pulsewidth
tWLWH
tAVLL
Address Valid after ALE Low
Address Hold after ALE Low
tLLAX
ALE Low to RD or WR Low
tLLWL
tAVWL
Address Valid to RD or WR Low
Data Valid to WR Transition
tQVWX
Data Setup before WR
tQVWH
tWHQX
Data and Address Hold after WR
tWHLH
RD or WR High to ALE High
400
43
48
200
203
33
433
33
43
6tCK – 100
tCK – 40
tCK – 35
3tCK – 50
4tCK – 130
tCK – 50
7tCK – 150
tCK – 50
tCK – 40
ns
ns
ns
ns
ns
ns
ns
ns
ns
300
123
MCLK
ALE (O)
tWHLH
PSEN (O)
tLLWL
tWLWH
WR (O)
tAVWL
tAVLL
tLLAX
tQVWX
A0–A7
PORT 2 (O)
tWHQX
tQVWH
DATA
A16–A23
A8–A15
Figure 53. External Data Memory Write Cycle
REV. E
–49–
3tCK + 50
6tCK – 100
ADuC812
Parameter
Min
UART TIMING (Shift Register Mode)
tXLXL
Serial Port Clock Cycle Time
Output Data Setup to Clock
tQVXH
Input Data Setup to Clock
tDVXH
Input Data Hold after Clock
tXHDX
tXHQX
Output Data Hold after Clock
700
300
0
50
12 MHz
Typ Max
Min
Variable Clock
Typ
1.0
12tCK
10tCK – 133
2tCK + 133
0
2tCK – 117
Max
Unit
µs
ns
ns
ns
ns
ALE (O)
tXLXL
TxD
(OUTPUT CLOCK)
7
6
1
0
SET RI
OR
SET TI
tQVXH
tXHQX
RxD
(OUTPUT DATA)
MSB
BIT6
tDVXH
RxD
(INPUT DATA)
MSB
LSB
BIT1
tXHDX
BIT6
BIT1
LSB
Figure 54. UART Timing in Shift Register Mode
–50–
REV. E
ADuC812
Parameter
Min
Max
Unit
2
I C COMPATIBLE INTERFACE TIMING
SCLOCK Low Pulsewidth
tLOW
tHIGH
SCLOCK High Pulsewidth
Start Condition Hold Time
tHD; STA
Data Setup Time
tSU; DAT
Data Hold time
tHD; DAT
tSU; STA
Setup time for Repeated Start
Stop Condition Setup Time
tSU; STO
Bus Free Time between a STOP
tBUF
Condition and a START Condition
Rise Time for Both SCLOCK and SDATA
tR
Fall Time for Both SCLOCK and SDATA
tF
tSUP1
Pulsewidth of Spike Suppressed
1.3
0.6
0.6
100
0
0.6
0.6
µs
µs
µs
µs
µs
µs
µs
0.9
1.3
µs
ns
ns
ns
300
300
50
tBUF
tSUP
SDATA (I/O)
MSB
LSB
tHD; STA
tHD; STA
SCLK (I)
2–7
tR
tLOW
tSU; STA
9
8
PS
tSUP
Figure 55. I2C Compatible Interface Timing
REV. E
–51–
MSB
tHD; DAT
tHIGH
1
STOP
START
CONDITION CONDITION
ACK
tSU; DAT
tHD; DAT
tSU; STO
tR
1
S(R)
REPEATED
START
tF
ADuC812
Parameter
Min
SPI MASTER MODE TIMING (CPHA = 1)
tLOW
SCLOCK Low Pulsewidth
tSH
SCLOCK High Pulsewidth
Data Output Valid after SCLOCK Edge
tDAV
Data Input Setup Time before SCLOCK Edge
tDSU
Data Input Hold Time after SCLOCK Edge
tDHD
tDF
Data Output Fall Time
Data Output Rise Time
tDR
SCLOCK Rise Time
tSR
tSF
SCLOCK Fall Time
Typ
Max
330
330
50
100
100
10
10
10
10
25
25
25
25
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
SCLOCK
(CPOL = 0)
t SL
t SH
t SR
t SF
SCLOCK
(CPOL = 1)
t DAV
t DF
MSB
MOSI
MISO
LSB
BIT 6–1
MSB IN
t DSU
t DR
BIT 6–1
LSB IN
t DHD
Figure 56. SPI Master Mode Timing (CPHA = 1)
–52–
REV. E
ADuC812
Parameter
Min
SPI MASTER MODE TIMING (CPHA = 0)
tSL
SCLOCK Low Pulsewidth
tSH
SCLOCK High Pulsewidth
Data Output Valid after SCLOCK Edge
tDAV
Data Output Setup before SCLOCK Edge
tDOSU
Data Input Setup Time before SCLOCK Edge
tDSU
tDHD
Data Input Hold Time after SCLOCK Edge
Data Output Fall Time
tDF
Data Output Rise Time
tDR
tSR
SCLOCK Rise Time
tSF
SCLOCK Fall Time
Typ
Max
330
330
50
150
100
100
10
10
10
10
25
25
25
25
SCLOCK
(CPOL = 0)
t SL
t SH
t SF
t SR
SCLOCK
(CPOL = 1)
t DAV
t DF
t DOSU
MSB
MOSI
MISO
MSB IN
t DSU
t DR
BIT 6–1
BIT 6–1
LSB
LSB IN
t DHD
Figure 57. SPI Master Mode Timing (CPHA = 0)
REV. E
–53–
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ADuC812
Parameter
Min
SPI SLAVE MODE TIMING (CPHA = 1)
tSS
SS to SCLOCK Edge
tSL
SCLOCK Low Pulsewidth
SCLOCK High Pulsewidth
tSH
Data Output Valid after SCLOCK Edge
tDAV
Data Input Setup Time before SCLOCK Edge
tDSU
tDHD
Data Input Hold Time after SCLOCK Edge
Data Output Fall Time
tDF
Data Output Rise Time
tDR
tSR
SCLOCK Rise Time
SCLOCK Fall Time
tSF
tSFS
SS High after SCLOCK Edge
Typ
Max
0
330
330
50
100
100
10
10
10
10
25
25
25
25
0
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
SS
t SFS
t SS
SCLOCK
(CPOL = 0)
t SL
t SH
t SF
t SR
SCLOCK
(CPOL = 1)
t DAV
MISO
MOSI
t DR
t DF
MSB
BIT 6–1
MSB IN
t DSU
BIT 6–1
LSB
LSB IN
t DHD
Figure 58. SPI Slave Mode Timing (CPHA = 1)
–54–
REV. E
ADuC812
Parameter
Min
SPI SLAVE MODE TIMING (CPHA = 0)
tSS
SS to SCLOCK Edge
tSL
SCLOCK Low Pulsewidth
SCLOCK High Pulsewidth
tSH
Data Output Valid after SCLOCK Edge
tDAV
Data Input Setup Time before SCLOCK Edge
tDSU
tDHD
Data Input Hold Time after SCLOCK Edge
Data Output Fall Time
tDF
Data Output Rise Time
tDR
tSR
SCLOCK Rise Time
SCLOCK Fall Time
tSF
Data Output Valid after SS Edge
tDOSS
tSFS
SS High After SCLOCK Edge
Typ
Max
0
330
330
50
100
100
10
10
10
10
25
25
25
25
20
0
SS
t SFS
t SS
SCLOCK
(CPOL = 0)
t SH
t SL
t SR
t SF
SCLOCK
(CPOL = 1)
t DAV
t DOSS
t DF
MSB
MISO
MOSI
MSB IN
t DSU
t DR
BIT 6–1
BIT 6–1
LSB
LSB IN
t DHD
Figure 59. SPI Slave Mode Timing (CPHA = 0)
REV. E
–55–
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ADuC812
OUTLINE DIMENSIONS
52-Lead Metric Quad Flat Package [MQFP]
(S-52)
Dimensions shown in millimeters
1.03
0.88
0.73
14.15
13.90 SQ
13.65
2.45
MAX
39
27
40
SEATING
PLANE
26
7.80
REF
10.20
10.00 SQ
9.80
TOP VIEW
(PINS DOWN)
VIEW A
PIN 1
52
14
1
0.23
0.11
13
0.65 BSC
0.38
0.22
2.10
2.00
1.95
7
0
0.10 MIN
COPLANARITY
VIEW A
ROTATED 90 CCW
COMPLIANT TO JEDEC STANDARDS MO-022-AC-1
56-Lead Lead Frame Chip Scale Package [LFCSP]
8 x 8 mm Body
(CP-56)
Dimensions shown in millimeters
8.00
BSC SQ
0.60 MAX
0.60 MAX
43
7.75
BSC SQ
TOP
VIEW
0.20
REF
12 MAX
6.25
6.10 SQ
5.95
BOTTOM
VIEW
0.50
0.40
0.30
1.00
0.90
0.80
PIN 1
INDICATOR
56 1
42
PIN 1
INDICATOR
0.30
0.23
0.18
29
28
15 14
6.50
REF
0.70 MAX
0.65 NOM
0.05 MAX
0.02 NOM
0.50 BSC
SEATING
PLANE
COPLANARITY
0.08
COMPLIANT TO JEDEC STANDARDS MO-220-VLLD-2
–56–
REV. E
ADuC812
Revision History
Location
Page
4/03—Data Sheet changed from REV. D to REV. E.
Updated OUTLINE DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
2/03—Data Sheet changed from REV. C to REV. D.
Added CP-56 Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Global
Edits to GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Added 56-Lead LFCSP PIN CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Updated ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Added I2C COMPATIBLE INTERFACE TIMING Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Added new Figure 55 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Updated OUTLINE DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
03/02—Data Sheet changed from REV. B to REV. C.
Edits to FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Edits to GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Edits to FUNCTIONAL BLOCK DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Edits to SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Edits to PIN CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Edits to PIN FUNCTION DESCRIPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Edits to Figure 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Edits to SERIAL PERIPHERAL INTERFACE Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Edits to TABLE XI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Edits to TABLE XXIII . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Edits to TABLES XXIV, XXV, and XXVI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
10/01—Data Sheet changed from REV. A to REV. B.
Entire Data Sheet Revised . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . All
REV. E
–57–
–58–
–59–
–60–
C00208–0–4/03(E)