Fairchild FAN5365 1a / 0.8a, 6mhz digitally programmable regulator Datasheet

FAN5365
1A / 0.8A, 6MHz Digitally Programmable Regulator
Features
Description
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
The FAN5365 is a high-frequency, ultra-fast transient
response, synchronous step-down, DC-DC converter
optimized for low-power applications using small, low-cost
inductors and capacitors. The FAN5365 supports up to
800mA or 1A load current.
High Efficiency (>88%) at 6MHz
800mA or 1A Output Current
Regulation Maintained with VIN from 2.3V to 5.5V
6-Bit VOUT Programmable from 0.75 to 1.975V
6MHz Fixed-Frequency Operation (PWM Mode)
Excellent Load and Line Transient Response
Small Size, 470nH Inductor Solution
±2% DC Voltage Accuracy in PWM Mode
25ns Minimum On-Time
High-Efficiency, Low-Ripple, Light-Load PFM
Smooth Transition between PWM and PFM
40μA Operating PFM Quiescent Current
2
I C™-Compatible Interface up to 3.4Mbps
2
Pin-Selectable or I C™ Programmable Output Voltage
9-Bump, 1.27 x 1.29mm, 0.4mm Pitch WLCSP Package
Applications
ƒ
ƒ
ƒ
ƒ
ƒ
®
®
3G, WiFi , WiMAX™, and WiBro Data Cards
®
Netbooks , Ultra-Mobile PCs
SmartReflex™-Compliant Power Supply
Split Supply DSPs and μP Solutions OMAP™, XSCALE™
®
Handset Graphic Processors (NVIDIA , ATI)
The FAN5365 is ideal for mobile phones and similar portable
applications powered by a single-cell Lithium-Ion battery.
2
With an output voltage range adjustable via I C™ interface
from 0.75V to 1.975V, it supports low-voltage DSPs and
processors, core power supplies, and memory modules in
smart phones, data cards, and hand-held computers.
The FAN5365 operates at 6MHz (nominal) fixed switching
frequency in PWM mode.
During light-load conditions, the regulator includes a PFM
mode to enhance light-load efficiency. The regulator
transitions smoothly between PWM and PFM modes with no
glitches on VOUT. In hardware shutdown, the current
consumption is reduced to less than 200nA.
The serial interface is compatible with fast / standard mode,
2
fast mode plus, and high-speed mode I C specifications,
allowing transfers up to 3.4Mbps. This interface is used for
dynamic voltage scaling with 12.5mV voltage steps, for
reprogramming the mode of operation (PFM or forced
PWM), or to disable/enable the output voltage.
The chip's advanced protection features include short-circuit
protection and current and temperature limits. During a
sustained over-current event, the IC shuts down and restarts
after a delay to reduce average power dissipation into a
fault.
During startup, the IC controls the output slew rate to
minimize input current and output overshoot at the end of
soft-start. The IC maintains a consistent soft-start ramp,
regardless of output load during startup.
The FAN5365 is available in a 1.27 x 1.29mm, 9-bump
WLCSP package.
All trademarks are the property of their respective owners
© 2008 Fairchild Semiconductor Corporation
FAN5365 • Rev. 1.0.4
www.fairchildsemi.com
FAN5365 — 1A / 0.8A, 6MHz Digitally Programmable Regulator
November 2010
(1)
Part Number
Option
Slave Address LSB
A2
FAN5365UC00X
00
FAN5365UC02X
0
A1
Output
Current
A0
1
mA
0
Power-up
Defaults
VOUT Programming
800
Min.
Max.
0.7500
Package
VSEL0
VSEL1
(3)
1.05
1.20
WLCSP-09
(3)
0.95
1.10
WLCSP-09
1.4375
02
1
1
0
800
0.7500
(2)
03
0
0
0
1000
0.7500
1.5375
1.00
1.20
WLCSP-09
(2)
06
0
0
0
1000
1.1875
1.9750
1.80
1.80
WLCSP-09
FAN5365UC03X
FAN5355UC06X
1.4375
Notes:
1. The “X” designator on the part number indicates tape and reel packaging.
2. Preliminary; not full production release at this time. Contact a Fairchild representative for information.
3. VOUT is limited to the maximum voltage for all VSEL codes greater than the maximum VOUT listed.
Typical Application
VIN
VIN
Q1
CIN
EN
VSEL
SDA
VOUT
SW
MODULATOR
Q2
L
COUT
SCL
PGND
AGND
VOUT
Figure 1. Typical Application
Table 1. Recommended External Components
Component
L (LOUT)
COUT
(5)
CIN
Description
470nH Nominal
Vendor
Murata, TDK, FDK
0603 (1.6x0.8x0.8), 10μF X5R
Various
0402 (1x0.5x0.25), 4.7μF X5R
Taiyo-Yuden
Parameter
L
(4)
Min.
Typ.
Max.
Units
390
470
600
nH
DCR (Series R)
(6)
C
80
2.2
10.0
1.6
4.7
mΩ
15.0
μF
μF
Notes:
4. Minimum L incorporates tolerance, temperature, and partial saturation effects (L decreases when increasing current).
5. A capacitor similar to CIN can be used for COUT. With 1.4V of bias, a 4.7μF 0402 capacitor minimum value is 2.5μF.
The regulator is stable, but transient response degraded due to large signal effects.
6. Minimum C is a function of initial tolerance, maximum temperature, and the effective capacitance being reduced due to
frequency, dielectric, and voltage bias effects. CIN is biased with a higher voltage which reduces its effective capacitance
by a larger amount.
© 2008 Fairchild Semiconductor Corporation
FAN5365 • Rev. 1.0.4
www.fairchildsemi.com
2
FAN5365 — 1A / 0.8A, 6MHz Digitally Programmable Regulator
Ordering Information
A1
A2
A3
A3
A2
A1
B1
B2
B3
B3
B2
B1
C1
C2
C3
C3
C2
C1
Bumps Facing Down
Bumps Facing Up
Figure 2. WLCSP-09, 0.4mm Pitch
Pin Definitions
Pin #
Name
Description
A1
VSEL
Voltage Select. When HIGH, VOUT is set by VSEL1. When LOW, VOUT is set by VSEL0. This behavior
2
can be overridden through I C register settings. This pin should not be left floating.
A2
VIN
Input Voltage. Connect to input power source. The connection from this pin to CIN should be as short as
possible.
A3
SDA
SDA. I C interface serial data. This pin should not be left floating.
B1
SW
Switching Node. Connect to output inductor.
B2
SCL
SCL. I C interface serial clock. This pin should not be left floating.
B3
EN
Enable. When this pin is HIGH, the circuit is enabled. When LOW, part enters shutdown mode and
input current is minimized. This pin should not be left floating.
C1
VOUT
Output Voltage Monitor. Tie this pin to the output voltage at COUT. This is a signal input pin to the
control circuit and does not carry DC current.
C2
PGND
Power GND. Power return for gate drive and power transistors. Connect to AGND on PCB. The
connection from this pin to the bottom of CIN should be as short as possible.
C3
AGND
Analog GND. This is the signal ground reference for the IC. All voltage levels are measured with
respect to this pin. AGND should be connected to PGND at a single point.
2
2
© 2008 Fairchild Semiconductor Corporation
FAN5365 • Rev. 1.0.4
www.fairchildsemi.com
3
FAN5365 — 1A / 0.8A, 6MHz Digitally Programmable Regulator
Pin Configuration
Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable
above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition,
extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute
maximum ratings are stress ratings only.
Symbol
VCC
Parameter
Min.
VIN, SW Pins
–0.3
6.5
VOUT
–0.3
2.5
Other Pins
ESD
Max.
V
(7)
–0.3
Electrostatic Discharge Protection
Units
VIN + 0.3
Human Body Model, JESD22-A114
3
Charged Device Model, JESD22-C101
1
KV
TJ
Junction Temperature
–40
+150
°C
TSTG
Storage Temperature
–65
+150
°C
+260
°C
TL
Lead Soldering Temperature, 10 Seconds
Note:
7. Lesser of 6.5V or VCC+0.3V.
Recommended Operating Conditions
The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended operating
conditions are specified to ensure optimal performance to the datasheet specifications. Fairchild does not recommend
exceeding them or designing to absolute maximum ratings.
Symbol
VIN
VCCIO
Parameter
Supply Voltage
SDA and SCL Voltage Swing
(8)
Min.
Max.
Units
2.3
5.5
V
1.2
2.0
V
TA
Ambient Temperature
–40
+85
°C
TJ
Junction Temperature
–40
+125
°C
Note:
2
8. The I C interface operates with tHD;DAT = 0 as long as the pull-up voltage for SDA and SCL is less than 2.5V. If voltage
2
swings greater than 2.5V are required (for example, if the I C bus is pulled up to VIN), the minimum tHD;DAT must be
2
increased to 80ns. Most I C masters change SDA near the midpoint between the falling and rising edges of SCL, which
provides ample tHD;DAT.
Dissipation Ratings(9)
Package
Wafer-Level Chip-Scale Package (WLCSP)
(10)
RθJA
110ºC/W
Power Rating
at TA ≤ 25°C
Derating Factor
> TA = 25ºC
900mW
9mW/ºC
Notes:
9. Maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any
allowable ambient temperature is PD = [TJ(max) - TA ] / θJA.
10. This thermal data is measured with a high-K board (four-layer board, according to the JESD51-7 JEDEC standard).
© 2008 Fairchild Semiconductor Corporation
FAN5365 • Rev. 1.0.4
www.fairchildsemi.com
4
FAN5365 — 1A / 0.8A, 6MHz Digitally Programmable Regulator
Absolute Maximum Ratings
Unless otherwise noted, over the recommended operating range for VIN and TA, EN = VSEL = SCL = SDA = 1.8V, and register
VSEL0[6] bit = 1. Typical values are at VIN = 3.6V, TA = 25°C. Circuit and components according to Figure 1.
Symbol Parameter
Conditions
Min.
Typ.
Max.
Units
IO = 0mA, PFM Mode, 2.3V<=VIN<=4.5V
IO = 0mA, PFM Mode, 2.3V<=VIN<=5.5V
IO = 0mA, 6MHz PWM Mode
40
40
6.3
55
65
μA
EN = GND
0.1
1.0
N/A
N/A
2.18
2.02
160
2.25
Power Supplies
IQ
ISD
VUVLO
Quiescent Current
Shutdown Supply Current
Under-Voltage Lockout Threshold
VUVHYST Under-Voltage Lockout Hysteresis
ENABLE, VSEL, SDA, SCL
VIH
HIGH-Level Input Voltage
VIL
LOW-Level Input Voltage
IIN
Input Bias Current
Power Switch and Protection
P-Channel MOSFET On
RDS(ON)P
Resistance
ILKGP
P-Channel Leakage Current
N-Channel MOSFET On
RDS(ON)N
Resistance
ILKGN
N-Channel Leakage Current
ILIMPK
P-MOS Current Limit
TLIMIT
Thermal Shutdown
THYST Thermal Shutdown Hysteresis
Frequency Control
(11)
fSW
Switching Frequency
Output Regulation
VOUT
VOUT Accuracy
EN = VIN, EN_DCDC bit = 0,
SDA = SCL = 1.8V (Software Shutdown)
VIN Rising
VIN Falling
1.95
mA
1.05
Input Tied to GND or VIN
0.01
VIN = 3.6V
300
VDS = 5.5V
0.2
VIN = 3.6V
200
VDS = 5.5V
Options 00, 02
Options 03, 06
IOUT(DC) = 0, Forced PWM, VOUT = VSEL1
Default Value
2.3V ≤ VIN ≤ 5.5V, VOUT from Minimum to
Maximum, IOUT(DC) = 0 to 1A, Forced PWM
2.3V ≤ VIN ≤ 5.5V, VOUT from Minimum to
Maximum, IOUT(DC) = 0 to 1A, Auto
PWM/PFM
ΔVOUT
ΔILOAD
Load Regulation
IOUT(DC) = 0 to 1A, Forced PWM
ΔVOUT
ΔVIN
Line Regulation
VRIPPLE
Output Ripple Voltage
V
V
mV
V
V
μA
mΩ
1.0
μA
mΩ
μA
0.3
1350
1550
150
20
1.0
1600
1840
6.0
6.6
MHz
–1.5
1.5
%
–2.0
2.0
%
–2.0
3.5
%
1150
1300
PWM Operation
0.4
1.00
μA
5.4
mA
°C
°C
–0.2
%/A
2.3V ≤ VIN ≤ 5.5V, IOUT(DC) = 300mA,
Forced PWM
0
%/V
PWM Mode, VOUT = 1.2V
PFM Mode, IOUT(DC) = 10mA
4
16
mVP-P
mVP-P
Continued on the following page…
© 2008 Fairchild Semiconductor Corporation
FAN5365 • Rev. 1.0.4
www.fairchildsemi.com
5
FAN5365 — 1A / 0.8A, 6MHz Digitally Programmable Regulator
Electrical Specifications
Unless otherwise noted, over the recommended operating range for VIN and TA, EN = VSEL = SCL = SDA = 1.8V, and register
VSEL0[6] bit = 1. Typical values are at VIN = 3.6V, TA = 25°C. Circuit and components according to Figure 1.
Symbol Parameter
Conditions
Min. Typ. Max. Units
DAC
Resolution
6
Differential Nonlinearity
Bits
Monotonicity Assured by Design
0.8
LSB
Timing
2
2
I CEN
EN HIGH to I C Start
tV(L-H)
VOUT LOW to HIGH Settling
Transition from 0.75V to 1.438V
VOUT Settled to within 2% of Setpoint
Regulator Enable to Regulated VOUT
RLOAD > 5Ω, to VOUT = Power-up Default
μs
250
μs
7
Soft-Start
tSS
140
180
μs
Notes:
11. Limited by the effect of tOFF minimum (see Figure 14 in Typical Performance Characteristics).
Block Diagram
VIN
VIN
Q1
DAC
EN
VSEL
SDA
I2C
INTERFACE
AND LOGIC
SCL
CIN
REF
FPWM
EN_REG
VOUT
SW
SOFT START
Q2
L
COUT
MODULATOR
PGND
CLK
VOUT
AGND
6 Mhz Osc
Figure 3 Block Diagram
© 2008 Fairchild Semiconductor Corporation
FAN5365 • Rev. 1.0.4
www.fairchildsemi.com
6
FAN5365 — 1A / 0.8A, 6MHz Digitally Programmable Regulator
Electrical Specifications (Continued)
Guaranteed by design.
Symbol
Parameter
fSCL
SCL Clock Frequency
tBUF
Bus-free Time between STOP and
START Conditions
tHD;STA
tLOW
tHIGH
START or Repeated START Hold
Time
SCL LOW Period
SCL HIGH Period
tSU;STA
Repeated START Setup Time
tSU;DAT
Data Setup Time
tHD;DAT
Data Hold Time
tRCL
SCL Rise Time
(8)
Conditions
Standard Mode
Fast Mode
Fast Mode Plus
High-Speed Mode, CB < 100pF
High-Speed Mode, CB < 400pF
Standard Mode
Fast Mode
Fast Mode Plus
Standard Mode
Fast Mode
Fast Mode Plus
High-Speed Mode
Standard Mode
Fast Mode
Fast Mode Plus
High-Speed Mode, CB < 100pF
High-Speed Mode, CB < 400pF
Standard Mode
Fast Mode
Fast Mode Plus
High-Speed Mode, CB < 100pF
High-Speed Mode, CB < 400pF
Standard Mode
Fast Mode
Fast Mode Plus
High-Speed Mode
Standard Mode
Fast Mode
Fast Mode Plus
High-Speed Mode
Standard Mode
Fast Mode
Fast Mode Plus
High-Speed Mode, CB < 100pF
High-Speed Mode, CB < 400pF
Standard Mode
Fast Mode
Fast Mode Plus
High-Speed Mode, CB < 100pF
High-Speed Mode, CB < 400pF
Min.
Typ.
Max.
Units
100
400
1000
3400
1700
kHz
4.7
1.3
0.5
4
600
260
160
4.7
1.3
0.5
160.0
320.0
4
600
260
60
120
4.7
600.0
260.0
160.0
250
100
50
10
0
0
0
0
0
20+0.1CB
20+0.1CB
20+0.1CB
10
20
μs
μs
ns
ns
ns
μs
ns
ns
ns
ns
μs
ns
ns
ns
ns
μs
ns
ns
ns
ns
3.45
900.00
450.00
70.00
150.00
1000
300
120
80
160
μs
ns
ns
ns
ns
ns
Continued on the following page…
© 2008 Fairchild Semiconductor Corporation
FAN5365 • Rev. 1.0.4
www.fairchildsemi.com
7
FAN5365 — 1A / 0.8A, 6MHz Digitally Programmable Regulator
I2C Timing Specifications
Guaranteed by design.
Symbol
Parameter
tFCL
SCL Fall Time
tRCL1
Rise Time of SCL after a Repeated
START Condition and after ACK Bit
tRDA
SDA Rise Time
tFDA
SDA Fall Time
tSU;STO
CB
Stop Condition Setup Time
Conditions
Standard Mode
Fast Mode
Fast Mode Plus
High-Speed Mode, CB < 100pF
High-Speed Mode, CB < 400pF
High-Speed Mode, CB < 100pF
High-Speed Mode, CB < 400pF
Standard Mode
Fast Mode
Fast Mode Plus
High-Speed Mode, CB < 100pF
High-Speed Mode, CB < 400pF
Standard Mode
Fast Mode
Fast Mode Plus
High-Speed Mode, CB < 100pF
High-Speed Mode, CB < 400pF
Standard Mode
Fast Mode
Fast Mode Plus
High-Speed Mode
Capacitive Load for SDA and SCL
© 2008 Fairchild Semiconductor Corporation
FAN5365 • Rev. 1.0.4
Min.
Typ.
20+0.1CB
20+0.1CB
20+0.1CB
10
20
10
20
20+0.1CB
20+0.1CB
20+0.1CB
10
20
20+0.1CB
20+0.1CB
20+0.1CB
10
20
4
600
120
160
Max.
300
300
120
40
80
80
160
1000
300
120
80
160
300
300
120
80
160
400
Units
ns
ns
ns
ns
μs
ns
ns
ns
pF
www.fairchildsemi.com
8
FAN5365 — 1A / 0.8A, 6MHz Digitally Programmable Regulator
I2C Timing Specifications (Continued)
tF
tSU;STA
tBUF
SDA
tR
SCL
TSU;DAT
tHD;STO
tHIGH
tLOW
tHD;STA
tHD;DAT
tHD;STA
REPEATED
START
START
STOP
START
2
Figure 4. I C Interface Timing for Fast Plus, Fast, and Slow Modes
tFDA
tRDA
REPEATED
START
tSU;DAT
STOP
SDAH
tSU;STA
tRCL1
SCLH
tFCL
tLOW
tHD;STA
REPEATED
START
tRCL
tSU;STO
tHIGH
tHD;DAT
note A
= MCS Current Source Pull-up
= RP Resistor Pull-up
Note A: First rising edge of SCLH after Repeated Start and after each ACK bit.
2
Figure 5. I C Interface Timing for High-Speed Mode
© 2008 Fairchild Semiconductor Corporation
FAN5365 • Rev. 1.0.4
www.fairchildsemi.com
9
FAN5365 — 1A / 0.8A, 6MHz Digitally Programmable Regulator
Timing Diagrams
100%
100%
90%
90%
80%
80%
Efficiency
Efficiency
Unless otherwise specified, Auto PWM/PFM, VIN = 3.6V, SCL = SCA = VSEL = EN = 1.8V, TA = 25°C; circuit and components
according to Figure 1.
70%
2.3V Auto PFM/PWM
60%
70%
2.3V Auto PFM/PWM
2.7V Auto PFM/PWM
60%
2.7V Auto PFM/PWM
3.6V Auto PFM/PWM
3.6V Auto PFM/PWM
4.2V Auto PFM/PWM
4.2V Auto PFM/PWM
50%
50%
5.5V Auto PFM/PWM
5.5V Auto PFM/PWM
3.6V Forced PWM
3.6V Forced PWM
40%
1
10
100
40%
1
1000
Output Current (mA)
100%
100%
90%
90%
80%
80%
Auto PFM/PWM
Efficiency
Efficiency
70%
50%
Forced PWM
40%
VIN=3.6V
Vout=0.75V
30%
70%
Auto PFM/PWM
60%
Forced PWM
40%
10%
10%
100
0%
1
1000
10
100
1000
Output Current (mA)
Output Current (mA)
Figure 9. Efficiency, Auto PWM/PFM vs. Forced PWM
at VOUT = 1.4375V
Figure 8. Efficiency, Auto PWM/PFM vs. Forced PWM
at VOUT = 0.75V
© 2008 Fairchild Semiconductor Corporation
FAN5365 • Rev. 1.0.4
VIN=3.6V
VOUT=1.4375V
30%
20%
10
1000
50%
20%
0%
1
100
Figure 7. Efficiency vs. Load and Input Supply
at VOUT = 1.2V
Figure 6. Efficiency vs. Load and Input Supply
at VOUT = 1.1V
60%
10
Output Current (mA)
www.fairchildsemi.com
10
FAN5365 — 1A / 0.8A, 6MHz Digitally Programmable Regulator
Typical Characteristics
Unless otherwise specified, Auto PWM/PFM, VIN = 3.6V, SCL = SCA = VSEL = EN = 1.8V, TA = 25°C; circuit and components
according to Figure 1.
1.112
1.212
1.110
1.210
1.108
1.208
1.106
1.206
Auto PFM/PWM
Auto PFM/PWM
1.204
V out( V )
V out( V )
1.104
Forced PWM
1.102
Forced PWM
1.202
1.100
1.200
1.098
1.198
1.096
1.196
1.094
1.194
1.092
1.192
1
10
100
Output Current(mA)
1000
1
10
100
Output Current(mA)
1000
Figure 11. Load Regulation, Auto PFM / PWM and
Forced PWM at VOUT = 1.2V
Figure 10. Load Regulation, Auto PFM / PWM and
Forced PWM at VOUT = 1.1V
1.450
0.760
1.448
0.758
Auto PFM/PWM
0.756
Auto PFM/PWM
1.446
Forced PWM
Forced PWM
1.444
1.442
V out( V )
V out( V )
0.754
1.440
0.752
1.438
1.436
0.750
1.434
0.748
1.432
1.430
0.746
1
10
100
Output Current(mA)
1
1000
10
Output Current(mA)
100
1000
Figure 13. Load Regulation, Auto PFM / PWM and
Forced PWM at VOUT = 1.4375V
Figure 12. Load Regulation, Auto PFM / PWM and
Forced PWM at VOUT = 0.75V
7.0
Frequency (MHz)
6.0
5.0
4.0
3.0
Vo=1.4375V
Vo=1.36V
2.0
1.0
Vo=1.3V
Vo=1.2V
0
200
400
600
800
1000
1200
IOUT (mA)
Figure 14. Effect of tOFF(MIN) on Reducing the PWM
Switching Frequency, VIN=2.3V
© 2008 Fairchild Semiconductor Corporation
FAN5365 • Rev. 1.0.4
www.fairchildsemi.com
11
FAN5365 — 1A / 0.8A, 6MHz Digitally Programmable Regulator
Typical Characteristics
Unless otherwise specified, Auto PWM/PFM, VIN = 3.6V, SCL = SCA = VSEL = EN = 1.8V, TA = 25°C; circuit and components
according to Figure 1.
Quiescent Current (µA)
55
15
-40°C
25°C
85°C
Quiescent Current (mA)
60
50
45
40
35
30
2.3
2.7
3.1
3.5
3.9
4.3
4.7
5.1
12
-40°C
25°C
85°C
9
6
3
2.3
5.5
2.7
3.1
3.5
3.9
4.3
4.7
5.1
5.5
VIN (V)
VIN (V)
Figure 15. Quiescent Current in PFM Mode vs. Input
Voltage and Temperature
Figure 16. Quiescent Current in PWM Mode vs. Input
Voltage and Temperature
0.8
80
-40°C
25°C
85°C
VOUT =1.2V
70
Rejection Ratio (dB)
Shutdown Current (µA)
1.0
0.6
0.4
0.2
VOUT =1.05V
60
50
40
30
20
10
0.0
2.3
2.7
3.1
3.5
3.9
4.3
4.7
5.1
0
5.5
0.1
1
10
10 0
100 0
VIN (V)
Frequency (KHz)
Figure 17. Shutdown Current (EN = 0) vs. Input Voltage
and Temperature
Figure 18. VIN Ripple Rejection (PSRR) in Forced PWM
at 200mA
© 2008 Fairchild Semiconductor Corporation
FAN5365 • Rev. 1.0.4
www.fairchildsemi.com
12
FAN5365 — 1A / 0.8A, 6MHz Digitally Programmable Regulator
Typical Characteristics
Unless otherwise specified, Auto PWM/PFM, VIN = 3.6V, SCL = SCA = VSEL = EN = 1.8V, TA = 25°C; circuit and components
according to Figure 1.
Figure 19. Combined Line/Load Transient 3.0 to 3.6VIN
Combined with 500 to 50mA Load Transient
Figure 20. Combined Line/Load Transient 3.6 to 3.0VIN
Combined with 50 to 500mA Load Transient
Figure 21. Combined Line/Load Transient 3.0 to 3.6VIN
Combined with 800 to 200mA Load Transient
Figure 22. Combined Line/Load Transient 3.6 to 3.0VIN
Combined with 200 to 800mA Load Transient
© 2008 Fairchild Semiconductor Corporation
FAN5365 • Rev. 1.0.4
www.fairchildsemi.com
13
FAN5365 — 1A / 0.8A, 6MHz Digitally Programmable Regulator
Typical Characteristics
Unless otherwise specified, Auto PWM/PFM, VIN = 3.6V, SCL = SCA = VSEL = EN = 1.8V, TA = 25°C; circuit and components
according to Figure 1.
Figure 23. VSEL Transition, Single Step (DefSlew = 7),
RLOAD = 24Ω
Figure 24. VSEL Transition, Single Step (DefSlew = 7),
RLOAD = 4Ω
Figure 25. VSEL Transition, DefSlew = 0, RLOAD = 24Ω
Figure 26. VSEL Transition, DefSlew = 0, RLOAD = 4Ω
© 2008 Fairchild Semiconductor Corporation
FAN5365 • Rev. 1.0.4
www.fairchildsemi.com
14
FAN5365 — 1A / 0.8A, 6MHz Digitally Programmable Regulator
Typical Characteristics
Unless otherwise specified, Auto PWM/PFM, VIN = 3.6V, SCL = SCA = VSEL = EN = 1.8V, TA = 25°C; circuit and components
according to Figure 1.
Figure 27. VSEL Transition, VSEL 1 to 0, RLOAD = 24Ω
Figure 28. VSEL Transition, VSEL 1 to 0, RLOAD = 4Ω
Figure 29. Shutdown, Output Discharge On
Figure 30. Shutdown, Output Discharge Off
© 2008 Fairchild Semiconductor Corporation
FAN5365 • Rev. 1.0.4
www.fairchildsemi.com
15
FAN5365 — 1A / 0.8A, 6MHz Digitally Programmable Regulator
Typical Characteristics
Unless otherwise specified, Auto PWM/PFM, VIN = 3.6V, SCL = SCA = VSEL = EN = 1.8V, TA = 25°C; circuit and components
according to Figure 1.
Figure 31. Metallic Short Applied at VOUT
Figure 32. Over-Current Fault Response, RLOAD = 500mΩ
Figure 33. Soft Start, No Load
Figure 34. Soft Start, RLOAD = 1.5Ω
© 2008 Fairchild Semiconductor Corporation
FAN5365 • Rev. 1.0.4
www.fairchildsemi.com
16
FAN5365 — 1A / 0.8A, 6MHz Digitally Programmable Regulator
Typical Characteristics
Table 2. VSEL vs. VOUT
The FAN5365 is a synchronous buck regulator that typically
operates at 6MHz with moderate to heavy load currents. At
light load currents, the converter operates in power-saving
PFM mode. The regulator automatically transitions between
fixed-frequency PWM mode and variable-frequency PFM
mode to maintain the highest possible efficiency over the full
range of load current.
VSEL Value
Dec (NVSEL) Binary
0
000000
1
000001
2
000010
3
000011
4
000100
5
000101
6
000110
7
000111
8
001000
9
001001
10
001010
11
001011
12
001100
13
001101
14
001110
15
001111
16
010000
17
010001
18
010010
19
010011
20
010100
21
010101
22
010110
23
010111
24
011000
25
011001
26
011010
27
011011
28
011100
29
011101
30
011110
31
011111
32
100000
33
100001
34
100010
35
100011
36
100100
37
100101
38
100110
39
100111
40
101000
41
101001
42
101010
43
101011
44
101100
45
101101
46
101110
47
101111
48
110000
49
110001
50
110010
51
110011
52
110100
53
110101
54
110110
55
110111
56
111000
57
111001
58
111010
59
111011
60
111100
61
111101
62
111110
63
111111
The FAN5365 uses a very fast, non-linear control
architecture to achieve excellent transient response with
minimum-sized external components.
2
The FAN5365 integrates an I C-compatible interface,
allowing transfers up to 3.4Mbps. This communication
interface can be used to:
ƒ
Dynamically re-program the output voltage in 12.5mV
increments
ƒ
Reprogram the mode of operation to enable or disable
PFM mode
ƒ
Control voltage transition slew rate
ƒ
Enable / disable the regulator.
2
For more details, refer to the I C Interface and Register
Description sections.
Output Voltage Programming
VOUT is programmed according to the following equations:
Option
(12)
00, 02, 03
06
VOUT Equation
VOUT = 0.75 + NVSEL • 12.5mV
(1)
VOUT = 1.1875 + NVSEL • 12.5mV
(2)
Note:
12. For option 00 and 02, the maximum voltage is 1.4375V.
© 2008 Fairchild Semiconductor Corporation
FAN5365 • Rev. 1.0.4
Hex
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
20
21
22
23
24
25
26
27
28
29
2A
2B
2C
2D
2E
2F
30
31
32
33
34
35
36
37
38
39
3A
3B
3C
3D
3E
3F
00, 02
0.7500
0.7625
0.7750
0.7875
0.8000
0.8125
0.8250
0.8375
0.8500
0.8625
0.8750
0.8875
0.9000
0.9125
0.9250
0.9375
0.9500
0.9625
0.9750
0.9875
1.0000
1.0125
1.0250
1.0375
1.0500
1.0625
1.0750
1.0875
1.1000
1.1125
1.1250
1.1375
1.1500
1.1625
1.1750
1.1875
1.2000
1.2125
1.2250
1.2375
1.2500
1.2625
1.2750
1.2875
1.3000
1.3125
1.3250
1.3375
1.3500
1.3625
1.3750
1.3875
1.4000
1.4125
1.4250
1.4375
1.4375
1.4375
1.4375
1.4375
1.4375
1.4375
1.4375
1.4375
VOUT
03
0.7500
0.7625
0.7750
0.7875
0.8000
0.8125
0.8250
0.8375
0.8500
0.8625
0.8750
0.8875
0.9000
0.9125
0.9250
0.9375
0.9500
0.9625
0.9750
0.9875
1.0000
1.0125
1.0250
1.0375
1.0500
1.0625
1.0750
1.0875
1.1000
1.1125
1.1250
1.1375
1.1500
1.1625
1.1750
1.1875
1.2000
1.2125
1.2250
1.2375
1.2500
1.2625
1.2750
1.2875
1.3000
1.3125
1.3250
1.3375
1.3500
1.3625
1.3750
1.3875
1.4000
1.4125
1.4250
1.4375
1.4500
1.4625
1.4750
1.4875
1.5000
1.5125
1.5250
1.5375
06
1.1875
1.2000
1.2125
1.2250
1.2375
1.2500
1.2625
1.2750
1.2875
1.3000
1.3125
1.3250
1.3375
1.3500
1.3625
1.3750
1.3875
1.4000
1.4125
1.4250
1.4375
1.4500
1.4625
1.4750
1.4875
1.5000
1.5125
1.5250
1.5375
1.5500
1.5625
1.5750
1.5875
1.6000
1.6125
1.6250
1.6375
1.6500
1.6625
1.6750
1.6875
1.7000
1.7125
1.7250
1.7375
1.7500
1.7625
1.7750
1.7875
1.8000
1.8125
1.8250
1.8375
1.8500
1.8625
1.8750
1.8875
1.9000
1.9125
1.9250
1.9375
1.9500
1.9625
1.9750
www.fairchildsemi.com
17
FAN5365 — 1A / 0.8A, 6MHz Digitally Programmable Regulator
Circuit Description
All internal circuits remain de-biased and the IC is in a very
low quiescent current state until the following are true:
ƒ
VIN is above its rising UVLO threshold, and
ƒ
EN is HIGH.
Light-Load (PFM) Operation
The FAN5365 provides a low ripple, single-pulse, PFM mode
that ensures:
2
At that point, the IC begins a soft-start cycle, its I C interface is
enabled, and its registers are loaded with their default values.
ƒ
ƒ
ƒ
During the initial soft-start, VOUT ramps linearly to the
setpoint programmed in the VSEL register selected by the
VSEL pin. The soft-start features a fixed output voltage slew
rate of 20V/ms and achieves regulation approximately 90μs
after EN rises. PFM mode is enabled during soft-start until
the output is in regulation, regardless of the MODE bit
settings. This allows the regulator to start into a partially
charged output without discharging it; in other words, the
regulator does not allow current to flow from the load back to
the battery.
Smooth transitions between PFM and PWM modes
Single-pulse operation for low ripple
Predictable PFM entry and exit currents.
PFM begins after the inductor current has become
discontinuous, crossing zero during the PWM cycle for 32
consecutive cycles. PFM exit occurs when discontinuous
current mode (DCM) operation cannot supply sufficient
current to maintain regulation. During PFM mode, the
inductor current ripple is about 40% higher than in PWM
mode. The load current required to exit PFM mode is
thereby about 20% higher than the load current required to
enter PFM mode, providing sufficient hysteresis to prevent
“mode chatter.”
As soon as the output has reached its setpoint, the control
forces PWM mode for about 85μs to allow all internal control
circuits to calibrate.
While PWM ripple voltage is typically less than 4mVP-P, PFM
ripple voltage can be up to 30mVP-P during very light load. To
prevent significant undershoot when a load transient occurs,
the initial DC setpoint for the regulator in PFM mode is set
10mV higher than in PWM mode. This offset decays to about
5mV after the regulator has been in PFM mode for ~100μs.
The maximum instantaneous voltage in PFM is 30mV above
the setpoint.
Table 3. Soft-Start Timing
Symbol
Description
Value (μs)
tSSDLY
Time from EN to start of softstart ramp
25
tREG
VOUT ramp start to regulation
(VSEL–0.1) X 53
tPOK
PWROK (CONTROL2[5])
rising from tREG
11
PFM mode can be disabled by writing to the mode control
bits: CONTROL1[3:0] (see Table 5)
tCAL
Regulator stays in PWM
mode during this time
10
Output Voltage Transitions
The IC regulates VOUT to one of two setpoint voltages, as
determined by the VSEL pin and the HW_nSW bit.
EN
t REG
VSEL
Table 5.
t SSD LY
VOUT
t CA L (FPWM)
0
VSEL Pin HW_nSW Bit VOUT Setpoint
t P OK
PWROK
Figure 35. Soft-Start Timing
Table 4. EN_DCDC Behavior
2
EN_DCDC Bit
EN Pin
IC
REGULATOR
0
0
OFF
OFF
1
1
ON
ON
1
0
OFF
OFF
0
1
ON
OFF
© 2008 Fairchild Semiconductor Corporation
FAN5365 • Rev. 1.0.4
VOUT Setpoint and Mode Control
MODE_CTRL, CONTROL1[3:2] = 00
PFM
0
1
VSEL0
Allowed
1
1
VSEL1
Per MODE1
x
0
VSEL1
Per MODE1
If HW_nSW = 0, VOUT transitions are initiated through the
following sequence:
1.
2.
Write the new setpoint in VSEL1.
Write desired transition rate in DEFSLEW,
CONTROL2[2:0], and set the GO bit in CONTROL2[7].
If HW_nSW = 1, VOUT transitions are initiated either by
changing the state of the VSEL pin or by writing to the VSEL
register selected by the VSEL pin.
www.fairchildsemi.com
18
FAN5365 — 1A / 0.8A, 6MHz Digitally Programmable Regulator
Software Enable
The EN_DCDC bit, VSELx[7], can be used to enable the
regulator in conjunction with the EN pin. Setting EN_DCDC with
EN HIGH begins the soft-start sequence described above.
Power-Up, EN, and Soft-Start
All positive VOUT transitions inhibit PFM until the transition is
complete, which occurs at the end of tPOK(L-H).
When transitioning to a higher VOUT, the regulator can
perform the transition using multi-step or single-step mode.
Negative Transitions
When moving from VSEL = 1 to VSEL = 0, the regulator enters
PFM mode, regardless of the condition of the MODE bits,
and remains in PFM until the transition is complete. Reverse
current through the inductor is blocked, and the PFM
minimum frequency control inhibited, until the new setpoint is
reached; at which time, the regulator resumes control using
the mode established by MODE_CTRL. The transition time
from VHIGH to VLOW is controlled by load current and output
capacitance as:
Multi-Step Mode:
The internal DAC is stepped at a rate defined by DEFSLEW,
CONTROL2[2:0], ranging from 000 to 110. This mode
minimizes the current required to charge COUT and thereby
minimizes the current drain from the battery when
transitioning. The PWROK bit, CONTROL2[5], remains LOW
until about 1.5μs after the DAC completes its ramp.
V HIGH
t V (H−L ) = COUT •
VHIGH − VLOW
ILOAD
VOUT
(3)
V HIGH
V LOW
VSEL
tPOK(L-H)
PWROK
VOUT
V LOW
Figure 36. Multi-Step VOUT Transition
VSEL
Single-Step Mode:
Used if DEFSLEW, CONTROL2[2:0] = 111. The internal
DAC is immediately set to the higher voltage and the
regulator performs the transition as quickly as its current limit
circuit allows, while avoiding excessive overshoot.
Figure 38. Negative VOUT Transition
Protection Features
Current Limit / Auto-Restart
The regulator includes cycle-by-cycle current limiting, which
prevents the instantaneous inductor current from exceeding
the “PMOS Current Limit” threshold.
It is good practice to reduce the load current before making
positive VSEL transitions. This reduces the time required to
make positive load transitions and avoids current–limitinduced overshoot.
The IC enters “fault” mode after sustained over-current. If
current limit is asserted for more than 32 consecutive cycles
(about 20μs), the IC returns to shutdown state and remains
in that condition for ~80μs. After that time, the regulator
attempts to restart with a normal soft-start cycle. If the fault
has not cleared, it shuts down ~20μs later.
tV(L-H)
98 % V HIGH
If the fault is a short circuit, the initial current limit is ~30% of
the normal current limit, which produces a very small drain
on the system power source.
VOUT
Thermal Protection
When the junction temperature of the IC exceeds 150°C, the
device turns off all output MOSFETs and remains in a low
quiescent current state until the die cools to 130°C before
starting a normal soft-start cycle.
VLOW
VSEL
PWROK
tPOK(L-H)
PWROK
Figure 37 shows single-step transition timing. tV(L-H) is the
time it takes the regulator to settle to within 2% of the new
setpoint, typically 7μs for a full-range transition. The PWROK
bit, CONTROL2[5], goes LOW until the transition is complete
and VOUT settled. This typically occurs ~2μs after tV(L-H).
V HIGH
tV(L-H)
tPOK(L-H)
Figure 37. Single-Step VOUT Transition
© 2008 Fairchild Semiconductor Corporation
FAN5365 • Rev. 1.0.4
www.fairchildsemi.com
19
FAN5365 — 1A / 0.8A, 6MHz Digitally Programmable Regulator
Positive Transitions
Data change allowed
SDA
tH
I2C Interface
The FAN5365’s serial interface is compatible with standard,
2
fast, fast plus, and high-speed mode I C bus specifications.
The FAN5365’s SCL line is an input and its SDA line is a bidirectional open-drain output; it can only pull down the bus
when active. The SDA line only pulls LOW during data reads
and when signaling ACK. All data is shifted in MSB (bit 7) first.
t SU
SCL
Figure 39. Data Transfer Timing
Slave Address
Each bus transaction begins and ends with SDA and SCL
HIGH. A transaction begins with a “START” condition, which
is defined as SDA transitioning from 1 to 0 with SCL HIGH,
as shown in Figure 40.
In Table 6, A1 and A0 are according to the Ordering
Information table on page 2.
SDA
t HD;STA
Slave Address
MS Bit
2
Table 6. I C Slave Address
7
6
5
4
3
2
1
0
1
0
0
1
A2
A1
A0
R/ W
SCL
Figure 40. Start Bit
In Hex notation, the slave address assumes a 0 LSB. For
example, the hex slave address of option 00 is 94H.
A transaction ends with a “STOP” condition, which is defined
as SDA transitioning from 0 to 1 with SCL HIGH, shown in
Figure 41.
Register Addressing
FAN5365 has four user-accessible registers:
Slave Releases
Master Drives
2
Table 7. I C Register Address
SDA
Address
7
6
5
4
3
2
1
0
VSEL0
0
0
0
0
0
0
0
0
VSEL1
0
0
0
0
0
0
0
1
CONTROL1
0
0
0
0
0
0
1
0
CONTROL2
0
0
0
0
0
0
1
1
tHD;STO
ACK(0) or
NACK(1)
SCL
Figure 41. Stop Bit
During a read from the FAN5365 (Figure 44), the master
issues a “Repeated Start” command after sending the
register address and before resending the slave address.
The “Repeated Start” is a 1-to-0 transition on SDA while SCL
is HIGH, as shown in Figure 42.
Bus Timing
As shown in Figure 39, data is normally transferred when
SCL is LOW. Data is clocked in on the rising edge of SCL.
Typically, data transitions shortly at or after the falling edge
of SCL to allow ample time for the data to set up before the
next SCL rising edge.
Slave Releases
SDA
tSU;STA
tHD;STA
ACK(0) or
NACK(1)
SLADDR
MS Bit
SCL
Figure 42. Repeated Start Timing
© 2008 Fairchild Semiconductor Corporation
FAN5365 • Rev. 1.0.4
www.fairchildsemi.com
20
FAN5365 — 1A / 0.8A, 6MHz Digitally Programmable Regulator
Under-Voltage Lockout (UVLO)
The IC turns off all MOSFETs and remains in a low
quiescent current state until VIN rises above the UVLO
threshold.
Read and Write Transactions
The protocols for High-Speed (HS), Low-Speed (LS), and
Fast-Speed (FS) modes are identical, except the bus speed
for HS mode is 3.4MHz. HS mode is entered when the bus
master sends the HS master code 00001XXX after a start
condition. The master code is sent in Fast or Fast Plus mode
(less than 1MHz clock) and slaves do not acknowledge
(ACK) this transmission.
The following figures outline the sequences for data read
and write. Bus control is signified by the shading of the
Master Drives Bus
Symbol
Definition
S
START, Figure 40.
ACK. The slave drives SDA to 0 to acknowledge
the preceding packet.
NACK. The slave sends a 1 to NACK the
preceding packet.
Repeated START, see Figure 42.
STOP, see Figure 41.
A
A
The bus remains in HS mode until a stop bit (Figure 41) is
sent by the master. While in HS mode, packets are
separated by repeated start conditions.
S
Slave Address
0
.
Table 8. I2C Bit Definitions for Figure 43 and Figure 44
The master then generates a repeated start condition
(Figure 42) that causes all slaves on the bus to switch to HS
2
mode. The master then sends I C packets, as described
above, using the HS mode clock rate and timing.
7 bits
Slave Drives Bus
and
packet, defined as
All addresses and data are MSB first.
R
P
0
8 bits
0
8 bits
0
A
Reg Addr
A
Data
A
P
Figure 43. Write Transaction
7 bits
S
Slave Address
0
0
8 bits
0
A
Reg Addr
A
7 bits
R
Slave Address
1
0
8 bits
1
A
Data
A
P
Figure 44. Read Transaction
Register Descriptions
both the default values and the bit’s type (as defined in Table
10) for each available option.
Default Values
Each option of the FAN5365 (see Table 9) has different
default values for the some of the register bits. Table 9 defines
Table 9. Default Values and Bit Types for VSEL and CONTROL Registers
VSEL0
4 3
Option
7
6
5
00
02
03
06
1
1
1
1
1
1
1
1
0
0
0
1
Option
7
CONTROL1
6
5
4
00, 02
03, 06
1
1
0
0
1
1
1
1
1
0
0
0
0
0
1
1
2
1
0
VOUT
Option
7
6
5
0
0
1
0
0
0
0
0
0
0
0
1
1.05
0.95
1.00
1.80
00
02
03
06
1
1
1
1
1
1
1
1
1
0
1
1
3
2
1
0
Option
7
0
0
0
0
0
0
0
0
00, 02
03, 06
0
0
VSEL1
4 3
0
1
0
1
0
1
0
0
CONTROL2
6
5
4
1
0
0
0
0
0
2
1
0
VOUT
1
1
1
0
0
0
0
0
0
0
0
1
1.20
1.10
1.20
1.80
3
2
1
0
0
0
1
1
1
1
1
1
Table 10. Bit Type Definitions for Table 9
#
#
#
Active Bit Changing this bit changes the behavior of the converter, as described below.
Disabled Converter logic ignores changes made to this bit. Bit can be written and read-back.
2
Read-Only Writing to this bit through I C does not change the read-back value, nor does it change converter behavior.
© 2008 Fairchild Semiconductor Corporation
FAN5365 • Rev. 1.0.4
www.fairchildsemi.com
21
FAN5365 — 1A / 0.8A, 6MHz Digitally Programmable Regulator
High-Speed (HS) Mode
Table 11 defines the operation of each register bit.
Superscript characters define the default state for each
0,2,3,6
option. Superscripts
signify the default values for
options 00, 02, 03, and 06, respectively.
default for all options.
A
signifies the
Table 11. Bit Definitions
Bit
Name
Value
VSEL0
7
EN_DCDC
6
Reserved
5:0
DAC[5:0]
VSEL1
7
EN_DCDC
6
Reserved
5:0
DAC[5:0]
CONTROL1
0
A
1
A
1
A
Table 9
0
A
1
A
1
A
Table 9
7:6
Reserved
10
5
Reserved
1
A
Description
Register Address: 00
Device in shutdown regardless of the state of the EN pin. This bit is mirrored in VSEL1. A write
to bit 7 in either register establishes the EN_DCDC value.
Device enabled when EN pin is HIGH, disabled when EN is LOW.
6-bit DAC value to set VOUT.
Register Address: 01
Device in shutdown regardless of the state of the EN pin. This bit is mirrored in VSEL1. A write
to bit 7 in either register establishes the EN_DCDC value.
Device enabled when EN pin is HIGH, disabled when EN is LOW.
6-bit DAC value to set VOUT.
Register Address: 02
Vendor ID bits. Writing to these bits has no effect on regulator operation. These bits can be
2
used to distinguish between vendors via I C.
A
VOUT is controlled by VSEL1. Voltage transitions occur by writing to the VSEL1, then setting
the GO bit.
VOUT is programmed by the VSEL pin. VOUT = VSEL1 when VSEL is HIGH and VOUT = VSEL0
when VSEL is LOW.
Operation follows MODE0, MODE1.
PFM with automatic transitions to PWM, regardless of VSEL.
PFM disabled (forced PWM), regardless of VSEL.
PFM with automatic transitions to PWM, regardless of VSEL.
PFM disabled (forced PWM) when regulator output is controlled by VSEL1.
PFM with automatic transitions to PWM when regulator output is controlled by VSEL1.
0
4
HW_nSW
A
1
A
3:2 MODE_CTRL
1
MODE1
0
MODE0
00
01
10
11
A
0
1
A
0
1
CONTROL2
A
7
GO
6
OUTPUT_
DISCHARGE
5
PWROK
(read only)
4:3
Reserved
2:0
DEFSLEW
0
1
3,6
0
0,2
1
0
1
A
00
000
001
010
011
100
101
110
A
111
PFM with automatic transitions to PWM when VSEL is LOW. Changing this bit has no effect on
the operation of the regulator.
Register Address: 03
This bit has no effect when HW_nSW = 1. At the end of a VOUT transition, this bit is reset to 0.
Starts a VOUT transition if HW_nSW = 0.
When the regulator is disabled, VOUT is not discharged.
When the regulator is disabled, VOUT discharges through an internal pull-down.
VOUT is not in regulation or is in current limit.
VOUT is in regulation.
© 2008 Fairchild Semiconductor Corporation
FAN5365 • Rev. 1.0.4
VOUT slews at 0.15mV/μs during positive VOUT transitions.
VOUT slews at 0.30mV/μs during positive VOUT transitions.
VOUT slews at 0.60mV/μs during positive VOUT transitions.
VOUT slews at 1.20mV/μs during positive VOUT transitions.
VOUT slews at 2.40mV/μs during positive VOUT transitions.
VOUT slews at 4.80mV/μs during positive VOUT transitions.
VOUT slews at 9.60mV/μs during positive VOUT transitions.
Positive VOUT transitions use single-step mode (see Figure 37).
www.fairchildsemi.com
22
FAN5365 — 1A / 0.8A, 6MHz Digitally Programmable Regulator
Bit Definitions
FAN5365 — 1A / 0.8A, 6MHz Digitally Programmable Regulator
Physical Dimensions
0.03 C
2X
F
A
E
0.40
B
Ø0.20
Cu Pad
A1
PIN A1
INDEX AREA
0.40
D
Ø0.30
Solder Mask
0.03 C
2X
LAND PATTERN RECOMMENDATION
(NSMD PAD TYPE)
TOP VIEW
0.06 C
0.05 C
0.625
0.547
C
SEATING PLANE
D
0.378±0.018
E
0.208±0.021
SIDE VIEWS
NOTES:
A. NO JEDEC REGISTRATION APPLIES.
Ø0.260±0.020
9X
0.40
C. DIMENSIONS AND TOLERANCE
PER ASMEY14.5M, 1994.
C
B
A
0.40
B. DIMENSIONS ARE IN MILLIMETERS.
D. DATUM C IS DEFINED BY THE SPHERICAL
CROWNS OF THE BALLS.
(Y)±0.018
E. PACKAGE NOMINAL HEIGHT IS 586 MICRONS
±39 MICRONS (547-625 MICRONS).
F
1 2 3
(X)±0.018
F. FOR DIMENSIONS D, E, X, AND Y SEE
PRODUCT DATASHEET.
BOTTOM VIEW
G. DRAWING FILNAME: MKT-UC009ABrev2
Figure 45. 9-Ball WLCSP, 3X3 Array, 0.4mm Pitch, 250µm Ball
Product-Specific Dimensions
Product
D
E
X
Y
FAN5365UC
1.290 +/-0.030
1.270 +/-0.030
0.250
0.250
Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without
notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most
recent revision. Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions, specifically the warranty
therein, which covers Fairchild products.
Always visit Fairchild Semiconductor’s online packaging area for the most recent package drawings:
http://www.fairchildsemi.com/packaging/.
© 2008 Fairchild Semiconductor Corporation
FAN5365 • Rev. 1.0.4
www.fairchildsemi.com
23
FAN5365 — 1A / 0.8A, 6MHz Digitally Programmable Regulator
© 2008 Fairchild Semiconductor Corporation
FAN5365 • Rev. 1.0.4
www.fairchildsemi.com
24
Similar pages