Hirose FH39-25S-0.3SHW 0.3 mm pitch, 1.2 mm above the board, top and bottom contact, back-flip actuator Datasheet

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
NEW
0.3 mm Pitch, 1.2 mm above the board, Top and bottom Contact,
Back-Flip actuator Flexible Printed Circuit ZIF Connectors
FH39 Series
●Small size (39 pos. shown)
1.1mm
13.9
mm
■Features
1. Low-profile 0.3mm pitch connector with top
and bottom contact
(39
pos
.)
3.
45
m
m
●Easy FPC insertion
actuator
Usable via either its top or bottom contact point, this
connector achieves enhanced freedom in terms of the
product design.
2. High contact reliability thanks to the spring
terminal structure
Because both top and bottom contact points are springloaded, the contact point adapts to the FPC motion, and
high contact reliability is ensured.
FPC
3. Delivered with the actuator open
FPC can be immediately inserted without the need for the
opening of the actuator.
4. Easy FPC insertion
●Completely locked
Entry chamfers at all sides of the FPC insertion slot assure
correct insertion and positioning of the FPC.
5. Accepts standard FPC thickness
0.2mm thick standard Flexible Printed Circuit (FPC) can be
used. This is the only ultra-low profile ZIF connector using
standard FPC.
6. Conductive traces on the PCB can run under
the connector
No exposed contacts on the bottom of the connector.
7. Board placement with automatic equipment
Flat upper surface and tape and reel packaging facilitate
vacuum pick-up and placement.
Standard reel packaging contains 5000 connectors.
8. Halogen-free*
(FH39J Series)
*As defined by IEC61249-2-21
Br-900ppm maximum, Cl-900ppm maximum,
Cl + Br combined-1,500ppm maximum
2010.9
1
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
FH39 Series●0.3 mm Pitch, 1.2 mm above the board, Top and bottom Contact, Back-Flip actuator Flexible Printed Circuit ZIF Connectors
■Specifications
Current rating 0.2 A
Ratings
Voltage rating 30 Vrms AC
Recommended FPC
Operating
-55 to +85°C (Note 1)
temperature range
Operating
Relative humidity 90% max.
humidity range
(No condensation)
Storage
-10 to +50°C (Note 2)
temperature range
Storage
Relative humidity 90% max.
humidity range
(No condensation)
Thickness: 0.2 ± 0.03 mm, Gold plated contact pads
Item
Specification
1.Insulation resistance 50 Mø min.
2.Withstanding voltage No flashover or insulation breakdown
100 mø max.
3.Contact resistance
* Including FPC and FFC conductor resistance
Contact resistance: 100 mø max.
4.Durability
No damage, cracks, or parts dislocation
No electrical discontinuity of 1µs or longer
5.Vibration
Contact resistance: 100 mø max.
No damage, cracks, or parts dislocation
No electrical discontinuity of 1µs or longer
6.Shock
Contact resistance: 100 mø max.
No damage, cracks, or parts dislocation
Contact resistance: 100 mø max.
7.Humidity
Insulation resistance: 50 Mø min.
(Steady state)
No damage, cracks, or parts dislocation
Contact resistance: 100 mø max.
8.Temperature cycle
Insulation resistance: 50 Mø min.
No damage, cracks, or parts dislocation
9.Resistance to
No deformation of components affecting
soldering heat
performance
Conditions
100 V DC
90 Vrms AC / 1 minute
1 mA, AC max (AC: 1kHz)
10 cycles
Frequency: 10 to 55 Hz,
single amplitude of 0.75 mm,
10 cycles in each of the 3 axis
Acceleration of 981m/s2, 6 ms duration,
sine half-wave, 3 cycles in each of the 3 axis
96 hours at 40ç and humidity of 90 to 95%
Temperature:-55ç➝+15ç to +35ç➝+85ç➝+15ç to +35ç
Time: 30➝ 2 to 3 ➝ 30➝ 2 to 3 minutes
5 cycles
Reflow: At the recommended temperature profile
Manual soldering: 350ç ± 5ç for 5 seconds
Note 1: Includes temperature rise caused by current flow.
Note 2: The term "storage" refers to products stored for a long period prior to mounting and use.
The operating temperature and humidity range covers the non-conducting condition of installed connectors in storage,
shipment or during transportation after board mounting.
Note 3: Information contained in this catalog represents general requirements for this Series.
Contact us for the drawings and specifications for a specific part number shown.
■Materials
Part
Insulator
Contacts
Material
Finish
LCP
Color:Beige
PA
Color:Black
Phosphor bronze
Metalfittings
Remarks
Gold plated
-----------------
Pure tin reflow plated
-----------------
■Ordering information
FH 39 J - 51S - 0.3 SHW (10)
1
2
3
1 Series name:FH
2 Series No.:39
3 Blank :Standard
A :Long actuator type
J :Halogen-free requirements
(Flame retardance UL94V-0).
2
4
5
UL94V-0
6
7
4 Number of positions
FH39 :25 to 61
FH39A :67, (71 under planning)
FH39J :25 to 51
5 Contact pitch:0.3mm
6 Termination type
SHW...SMT horizontal staggered row mount type
7 Plating specifications
(10)...Gold plating with nickel barrier
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
FH39 Series●0.3 mm Pitch, 1.2 mm above the board, Top and bottom Contact, Back-Flip actuator Flexible Printed Circuit ZIF Connectors
■Connector Dimensions
A±0.15
0.3±0.1
B±0.1
3.55±0.2
(0.12)
(1.85)
0.6±0.1
Production LOT No.
(0.12)
0.6±0.1
C±0.1
B
(0.15)
(D)
(0.6)
(3.3)
E±0.1
B Detailed drawing
[FH39 Series]
1.1±0.1
(1.89)
(0.42) (FPC:t0.2mm)
(0.42) (FPC:t0.2mm)
1.1±0.1
(1.54)
1
0.1
)
1
0.47±0.1
0.1±0.15
0˚
0.1
:
:
:
:
0.3±0.1
0.1±0.15
3.25±0.15
(4.15)
(2.1)
(1.55)
(0.85)
(9
Note 1
2
3
4
˚)
(90
(3.85)
(2.1)
(1.55)
(0.85)
0.47±0.1
0.1±0.15
1
B Detailed drawing
[FH39A Series]
0.3±0.1
0.1±0.15
3.25±0.15
0.1
1
0.1
The coplanarity of each terminal lead within specified dimension is 0.1 mm Max.
Packaged on tape and reel only. Check packaging specification.
Slight variations in color of the plastic compounds do not affect form, fit or function of the connector.
After reflow, the terminal plating may change color, however this does not represent a quality issue.
Part Number
FH39-25S-0.3SHW(10)
FH39-27S-0.3SHW(10)
FH39-29S-0.3SHW(10)
FH39-33S-0.3SHW(10)
FH39-39S-0.3SHW(10)
FH39-45S-0.3SHW(10)
FH39-51S-0.3SHW(10)
FH39-61S-0.3SHW(10)
FH39A-67S-0.3SHW(10)
FH39A-71S-0.3SHW(10)
FH39J-25S-0.3SHW(10)
FH39J-33S-0.3SHW(10)
FH39J-39S-0.3SHW(10)
FH39J-45S-0.3SHW(10)
FH39J-51S-0.3SHW(10)
CL No.
580-1806-8-10
580-1805-5-10
580-1807-0-10
580-1803-0-10
580-1800-1-10
580-1802-7-10
580-1801-4-10
580-1808-3-10
580-1809-6-10
Under planning
580-1815-9-10
580-1814-6-10
580-1813-3-10
580-1811-8-10
580-1812-0-10
Number of contacts
25
27
29
33
39
45
51
61
67
71
25
33
39
45
51
A
9.7
10.3
10.9
12.1
13.9
15.7
17.5
20.5
22.3
23.5
9.7
12.1
13.9
15.7
17.5
B
6.6
7.2
7.8
9
10.8
12.6
14.4
17.4
19.2
20.4
6.6
9
10.8
12.6
14.4
C
7.2
7.8
8.4
9.6
11.4
13.2
15
18
19.8
21
7.2
9.6
11.4
13.2
15
All dimensions: mm
D
E
7.83
9.15
8.43
9.75
9.03
10.35
10.23
11.55
12.03
13.35
13.83
15.15
15.63
16.95
18.63
19.95
20.43
21.75
21.63
22.95
7.83
9.15
10.23
11.55
12.03
13.35
13.83
15.15
15.63
16.95
Tape and reel packaging (5,000 pieces/reel).
Order by number of reels.
3
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
FH39 Series●0.3 mm Pitch, 1.2 mm above the board, Top and bottom Contact, Back-Flip actuator Flexible Printed Circuit ZIF Connectors
Recommended
metal mask thickness : t=0.1
0.6±0.05
0.3±0.03
1±0.05
0.35±0.05
(Metal mask:0.35)
0.6±0.05
(Metal mask:0.25)
C±0.05
(Metal mask:1)
0.3±0.05
(Metal mask:0.57)
0.67±0.05
(3.65)
(0.2)
(0.1)
0.3±0.03
(Metal mask:0.25)
0.1±0.05
(Metal mask:0.42)
B±0.05
2.48±0.05
0.5±0.05
■Recommended PCB mounting pattern and metal mask dimensions
0.8±0.05
■Recommended FPC Dimensions
F±0.05
0.3±0.07
2.1±0.1
.2
0.1
0.2
0.3 +0.04
-0.03
3.65MIN (Stiffner)
R0
0.2±0.03
(Uncovered area)
0.3±0.02
2.25±0.1
2-
0.3±0.1
0.6±0.02
2.65±0.3
0.3 +0.04
-0.03
1.15±0.1
C±0.03
1.05±0.1
0.3±0.07
0.1±0.02
0.6±0.07
B±0.03
0.6±0.07
* Stiffener dimension should be 3.65mm min., and X dimension should be 0.5mm for improved flexibility of FPC.
Part Number
FH39-25S-0.3SHW(10)
FH39-27S-0.3SHW(10)
FH39-29S-0.3SHW(10)
FH39-33S-0.3SHW(10)
FH39-39S-0.3SHW(10)
FH39-45S-0.3SHW(10)
FH39-51S-0.3SHW(10)
FH39-61S-0.3SHW(10)
FH39A-67S-0.3SHW(10)
FH39A-71S-0.3SHW(10)
FH39J-25S-0.3SHW(10)
FH39J-33S-0.3SHW(10)
FH39J-39S-0.3SHW(10)
FH39J-45S-0.3SHW(10)
FH39J-51S-0.3SHW(10)
4
CL No.
580-1806-8-10
580-1805-5-10
580-1807-0-10
580-1803-0-10
580-1800-1-10
580-1802-7-10
580-1801-4-10
580-1808-3-10
580-1809-6-10
Under planning
580-1815-9-10
580-1814-6-10
580-1813-3-10
580-1811-8-10
580-1812-0-10
Number of contacts
25
27
29
33
39
45
51
61
67
71
25
33
39
45
51
B
6.6
7.2
7.8
9
10.8
12.6
14.4
17.4
19.2
20.4
6.6
9
10.8
12.6
14.4
C
7.2
7.8
8.4
9.6
11.4
13.2
15
18
19.8
21
7.2
9.6
11.4
13.2
15
All dimensions: mm
F
7.8
8.4
9
10.2
12
13.8
15.6
18.6
20.4
21.6
7.8
10.2
12
13.8
15.6
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
FH39 Series●0.3 mm Pitch, 1.2 mm above the board, Top and bottom Contact, Back-Flip actuator Flexible Printed Circuit ZIF Connectors
■Recommended FPC construction
1. Using Single-sided FPC
FPC : Flexible Printed Circuit
Material Name
Material
(25)
(25)
Covering film layer
Cover adhesive
Polyimide
Surface treatment
0.2µm thick gold plated over 1 to 5µm
nickel underplating
Copper foil
Cu 1oz
Base adhesive
Thermosetting adhesive
25
Base film
Polyimide
25
1 mil thick.
3
35
1 mil thick
Reinforcement material adhesive Thermosetting adhesive
40
Stiffener
75
Polyimide
3 mil thick
203
Total
2. Using Double-sided FPC
Material Thickness
(µm)
FPC : Flexible Printed Circuit
Material Name
Covering film layer
Material
Polyimide
1 mil thick.
Material Thickness
(µm)
(25)
(25)
Cover adhesive
Surface treatment
0.2µm thick gold plated over 1 to 5µm
nickel underplating
Through-hole copper
Cu
15
Copper foil
Cu 1/2oz
18
Base adhesive
Thermosetting adhesive
18
Base film
Polyimide
25
Base adhesive
Thermosetting adhesive
Copper foil
Cu 1/2oz
Cover adhesive
Thermosetting adhesive
25
Covering film layer
Polyimide
1 mil thick.
25
Reinforcement material adhesive Thermosetting adhesive
25
Stiffener
Polyimide
1 mil thick
3 mil thick
Total
3
18
(18)
25
197
* To prevent release of the FPC due to its bending, use of the double sided FPC with copper foil on the back side is NOT RECOMMENDED.
3. Precautions
1: This specification is a recommendation for the construction of the FH39 Series FPC (t=0.2±0.05).
2: For details about the construction, please contact the FPC manufacturers.
5
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
FH39 Series●0.3 mm Pitch, 1.2 mm above the board, Top and bottom Contact, Back-Flip actuator Flexible Printed Circuit ZIF Connectors
■Packaging Specification
●Embossed Carrier Tape Dimensions (Tape width to 24mm max.)
4±0.1
2±0.15
8±0.1
(0.3)
1.5
1.75±0.1
(2.1:FH39 series)
(2.4:FH39A series)
.1
+0 0
(K)
G±0.3
J±0.1
Ø
Flat surface,
for placement with
automatic equipment.
(4.65)
Unreeling direction
●Embossed Carrier Tape Dimensions (Tape width 32mm min.)
1.5
1.75±0.1
(1.85)
.1
+0 0
H±0.1
1.7
+0.15
0
1.5 +0.1
0
3)
●Reel Dimensions
(Ø80)
(Ø380)
(Ø1
(L: INSIDE)
(M: OUTSIDE)
6
G±0.3
(K)
J±0.1
Ø
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
FH39 Series●0.3 mm Pitch, 1.2 mm above the board, Top and bottom Contact, Back-Flip actuator Flexible Printed Circuit ZIF Connectors
All dimensions: mm
L
M
Part Number
CL No.
Number of contacts
G
H
J
K
FH39-25S-0.3SHW(10)
580-1806-8-10
25
24
---
11.5
11
25.4
29.4
FH39-27S-0.3SHW(10)
580-1805-5-10
27
24
---
11.5
11.6
25.4
29.4
FH39-29S-0.3SHW(10)
580-1807-0-10
29
24
---
11.5
12.2
25.4
29.4
FH39-33S-0.3SHW(10)
580-1803-0-10
33
24
---
11.5
13.4
25.4
29.4
FH39-39S-0.3SHW(10)
580-1800-1-10
39
24
---
11.5
15.2
25.4
29.4
FH39-45S-0.3SHW(10)
580-1802-7-10
45
32
28.4
14.2
17
33.4
37.4
FH39-51S-0.3SHW(10)
580-1801-4-10
51
32
28.4
14.2
18.8
33.4
37.4
FH39-61S-0.3SHW(10)
580-1808-3-10
61
44
40.4
20.2
21.8
45.4
49.4
FH39A-67S-0.3SHW(10)
580-1809-6-10
67
44
40.4
20.2
23.6
45.4
49.4
FH39A-71S-0.3SHW(10)
Under planning
71
44
40.4
20.2
24.8
45.4
49.4
FH39J-25S-0.3SHW(10)
580-1815-9-10
25
24
---
11.5
11
25.4
29.4
FH39J-33S-0.3SHW(10)
580-1814-6-10
33
24
---
11.5
13.4
25.4
29.4
FH39J-39S-0.3SHW(10)
580-1813-3-10
39
24
---
11.5
15.2
25.4
29.4
FH39J-45S-0.3SHW(10)
580-1811-8-10
45
32
28.4
14.2
17
33.4
37.4
FH39J-51S-0.3SHW(10)
580-1812-0-10
51
32
28.4
14.2
18.8
33.4
37.4
Tape and reel packaging (5,000 pieces/reel).
7
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
FH39 Series●0.3 mm Pitch, 1.2 mm above the board, Top and bottom Contact, Back-Flip actuator Flexible Printed Circuit ZIF Connectors
■Temperature Profile
MAX 250ç
250
230ç
Temperature
(ç)
200
200ç
150
150ç
100
50
25ç (60sec.) 90 sec. to 120 sec.
Preheating
0
Start
Time (Seconds)
8
(60sec.)
Soldering
HRS test condition
Solder method
:Reflow, IR/hot air
Environment
:Room air
Solder composition :Paste, 96.5%Sn/3.0%Ag/0.5%Cu
(Senju Metal Industry, Co., Ltd.'s
Part Number:M705-221CM5-32-10.5)
Test board
:Glass epoxy 25mm∞50mm∞0.8mm thick
Land dimensions :0.3mm∞0.5mm, 0.3mm∞0.67mm
Metal mask
:0.25∞0.42, 0.25∞0.57∞0.1mm thick
The temperature profiles shown are based on the above
conditions.
In individual applications the actual temperature may vary,
depending on solder paste type, volume / thickness and board
size / thickness. Consult your solder paste and equipment
manufacturer for specific recommendations.
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
FH39 Series●0.3 mm Pitch, 1.2 mm above the board, Top and bottom Contact, Back-Flip actuator Flexible Printed Circuit ZIF Connectors
■Connector Operation and Precautions
Operation
Exercise care when handling connectors. Follow recommendations given below.
1. As delivered
Delivered with the actuator open. There is no need to operate the
actuator prior to the insertion of the FPC.
The actuator is open when delivered in
the embossed tape packaging
2. FPC insertion
Align the FPC perpendicular with the connector and insert it firmly
all the way.
9
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
FH39 Series●0.3 mm Pitch, 1.2 mm above the board, Top and bottom Contact, Back-Flip actuator Flexible Printed Circuit ZIF Connectors
Operation
3. Locking
After FPC/FFC insertion, rotate the actuator down to a full stop, pushing it at the center.
Rotate
Excessive force after the actuator is already closed
Push at the center of the actuator.
Do NOT close at the ends.
4. FPC removal (Lock release)
Carefully rotate the actuator up to 90°, lifting it at the center.
Rotate (lift)
Do not attempt to open more than 90°
Lift at the center
Do not open (lift) at one end.
* The actuator opens by rotating it in the direction OPPOSITE to the direction of the insertion of the FPC.
DO NOT attempt to open it from the same side as the insertion of the FPC.
10
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
FH39 Series●0.3 mm Pitch, 1.2 mm above the board, Top and bottom Contact, Back-Flip actuator Flexible Printed Circuit ZIF Connectors
Precautions when mounting connectors on the PCB
◆Handling before mounting on PCB
Insertion of the FPC or operation of the actuator prior to mounting on the PCB is NOT RECOMMENDED.
◆PC board warpage
Minimize the warpage as much as possible. The connector is straight within 0.1 mm max. Make sure that the
mounting area flatness can accept the connector terminals without causing any failure of the solder joints.
◆Forces on the board
◆When braking the large PC board into individual boards exercise care NOT to damage the
installed connectors.
◆When attaching the boards or other components with the screws make sure that any stresses will
NOT cause board deflections affecting the mounting areas of the connector.
Connector
PCB
Other precautions
◆When hand soldering:
Do not perform hand soldering with the FPC inserted in the connector.
• Do not apply excessive heat or touch the soldering iron anywhere other than the connector leads.
• Do not use excessive amount of solder or flux compounds.
Operation of the actuator or contacts may be affected by excessive amounts of solder or flux compounds.
11