FR101SG-FR107SG 1.0 AMP. Glass Passivated Fast Recovery Rectifiers A-405 Features Glass passivated chip junction. High efficiency, Low VF High current capability High reliability High surge current capability Low power loss Mechanical Data Cases: Molded plastic Epoxy: UL 94V-0 rate flame retardant Polarity: Color band denotes cathode end High temperature soldering guaranteed: 260 oC /10 seconds/.375”,(9.5mm) lead lengths at 5lbs., (2.3kg) tension Mounting position: Any Weight: 0.22gram Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25 oC ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Symbol Type Number V RRM V RMS V DC Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current .375”(9.5mm) Lead Length @T A = 55 oC Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @ 1.0A Maximum DC Reverse Current @ TA=25 oC at Rated DC Blocking Voltage @ T A=125 oC Maximum Reverse Recovery Time ( Note 1 ) Typical Junction Capacitance ( Note 2 ) Typical thermal Resistance (Note 3) Operating Temperature Range FR FR FR FR FR FR FR 101SG 102SG 103SG 104SG 105SG 106SG 107SG 50 35 50 100 70 100 200 140 200 400 280 400 1000 700 1000 V V V 1.0 V IFSM 30 A VF 1.3 V IR 5.0 100 uA uA nS pF o C /W Trr Cj R θJA TJ ht t p : // 800 560 800 I(AV) 150 250 15 75 -65 to +150 -65 to +150 Storage Temperature Range T STG 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A Notes: 2. Measured at 1 MHz and Applied Reverse Voltage of 4.0 Volts D.C. 3. Mount on Cu-Pad Size 5mm x 5mm on P.C.B. Revision:20170701-P1 600 420 600 Units www.lgesemi .c o m 500 o o C C mail:[email protected] FR101SG-FR107SG 1.0 AMP. Glass Passivated Fast Recovery Rectifiers RATINGS AND CHARACTERISTIC CURVES (FR101SG THRU FR107SG) FIG.1- MAXIMUM FORWARD CURRENT DERATING CURVE FIG.2- TYPICAL REVERSE CHARACTERISTICS PER LEG 1000 Single Phase Half Wave 60Hz Resistive or Inductive Load 0.375" (9.5mm) Lead Length 1.25 1.00 INSTANTANEOUS REVERSE CURRENT. ( A) AVERAGE FORWARD CURRENT. (A) 1.50 0.75 0.50 0.25 0 0 25 50 75 100 125 150 175 o AMBIENT TEMPERATURE. ( C) 100 Tj=125 0C 10 Tj=75 0C 1 FIG.3- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT Tj=25 0C PEAK FORWARD SURGE CURRENT. (A) 50 0.1 0 40 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) 30 Tj=25 0C 20 FIG.5- TYPICAL FORWARD CHARACTERISTICS 10 10 8.3ms Single Half Sine Wave JEDEC Method 1 2 4 6 8 10 20 NUMBER OF CYCLES AT 60Hz 40 60 80 100 INSTANTANEOUS FORWARD CURRENT. (A) 0 FIG.4- TYPICAL JUNCTION CAPACITANCE JUNCTION CAPACITANCE.(pF) 100 Tj=25 0C 10 1.0 0.1 Tj=25oC Pulse Width=300 s 1% Duty Cycle .01 1 1 10 100 .4 .6 .8 REVERSE VOLTAGE. (V) 1.0 1.2 1.4 1.6 FORWARD VOLTAGE. (V) FIG.6- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50W NONINDUCTIVE 10W NONINDUCTIVE trr +0.5A (-) DUT (+) 50Vdc (approx) (-) PULSE GENERATOR (NOTE 2) 1W NON INDUCTIVE OSCILLOSCOPE (NOTE 1) NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms ht t p : // Revision:20170701-P1 0 -0.25A (+) -1.0A 1cm SET TIME BASE FOR 5/ 10ns/ cm www.lgesemi .c o m mail:[email protected]