MCC FR10A THRU FR10M omponents 21201 Itasca Street Chatsworth !"# $ % !"# Features • • • • 10 Amp Fast Recovery Rectifier Low Leakage Low Forward Voltage Drop High Current Capability Fast Switching Speed For High Efficiency 50 to 1000 Volts Maximum Ratings • Operating Temperature: -55°C to +150°C • Storage Temperature: -55°C to +150°C MCC Part Number FR10A FR10B FR10D FR10G FR10J FR10K FR10M Maximum Recurrent Peak Reverse Voltage 50V 100V 200V 400V 600V 800V 1000V DO-214AB (SMCJ) (Round Lead) Maximum DC Blocking Voltage Maximum RMS Voltage 35V 70V 140V 280V 420V 560V 700V H Cathode Band 50V 100V 200V 400V 600V 800V 1000V J A E D F IF(AV) 10 A 300A 8.3ms, half sine VF 1.30V IFM = 10.0A; TA = 25°C IR 10µA 50µA TA = 25°C TA = 100°C 150ns 250ns 500ns I F=0.5A, IR =1.0A, I rr =0.25A Trr DIMENSIONS TA = 55°C IFSM B G Electrical Characteristics @ 25°C Unless Otherwise Specified Average Forward Current Peak Forward Surge Current Maximum Instantaneous Forward Voltage Maximum DC Reverse Current At Rated DC Blocking Voltage Maximum Reverse Recovery Time FR10A-FR10G FR10J FR10K-FR10M C DIM A B C D E F G H J INCHES MIN .200 .177 .002 --.053 .168 .320 .239 .234 MM MIN 5.08 4.70 .05 --1.35 4.27 8.13 6.08 5.95 MAX .214 .203 .005 .02 .067 .179 .330 .243 .240 MAX 5.43 5.30 .13 .51 1.70 4.55 8.38 6.18 6.10 SUGGESTED SOLDER PAD LAYOUT 0.190 0.200” 0.070” *Pulse Test: Pulse Width 300µsec, Duty Cycle 1% www.mccsemi.com NOTE MCC FR10A thru FR10M Figure 1 Typical Forward Characteristics 20 Figure 2 Forward Derating Curve 10 12 6 4 10 2 Amps 25°C 8 1 .6 Amps .4 6 4 .2 2 .1 .06 0 .04 Single Phase, Half Wave 60Hz Resistive or Inductive Load 0 50 75 100 125 °C .02 .01 .8 1.0 1.2 1.4 1.6 1.8 Volts Instantaneous Forward Current - Amperes versus Instantaneous Forward Voltage - Volts Figure 3 Junction Capacitance 100 60 40 20 pF T J =25°C 10 6 4 2 1 .1 .2 .4 1 Volts 2 4 10 20 40 100 200 Junction Capacitance - pF versus Reverse Voltage - Volts www.mccsemi.com 400 1000 150 175 MCC FR10A thru FR10M Figure 4 Peak Forward Surge Current 300 250 200 150 Amps 100 50 0 1 2 4 6 8 10 20 40 60 80 100 Cycles Peak Forward Surge Current - Amperesversus Number Of Cycles At 60Hz - Cycles Figure 5 Reverse Recovery Time Characteristic And Test Circuit Diagram 50Ω 10Ω trr +0.5A 0 Pulse Generator Note 2 25Vdc 1Ω Notes: 1. Rise Time = 7ns max. Input impedance = 1 megohm, 22pF 2. Rise Time = 10ns max. Source impedance = 50 ohms 3. Resistors are non-inductive Oscilloscope Note 1 -0.25 -1.0 1cm Set Time Base for 20/100ns/cm www.mccsemi.com