EIC FWL005G Fast recovery glass passivated bridge rectifier Datasheet

FWL005G - FWL10G
PRV : 50 - 1000 Volts
Io : 1.0 Ampere
FAST RECOVERY GLASS
PASSIVATED BRIDGE RECTIFIERS
WOB
FEATURES :
0.39 (10.0)
0.31 (7.87)
Glass passivated chip
High case dielectric strength
High surge current capability
High reliability
Low reverse current
Low forward voltage drop
Ideal for printed circuit board
Fast switching for high efficiency
0.22 (5.59)
0.18 (4.57)
+
-
AC
1.00 (25.4)
MIN.
1.10 (27.9)
MIN.
*
*
*
*
*
*
*
*
0.034 (0.86)
0.028 (0.71)
MECHANICAL DATA :
* Case : Reliable low cost construction
utilizing molded plastic technique
* Epoxy : UL94V-O rate flame retardant
* Terminals : Plated leads solderable per
MIL-STD-202, Method 208 guaranteed
* Polarity : Polarity symbols marked on case
* Mounting position : Any
* Weight : 1.29 grams
AC
+
-
0.22 (5.59)
0.18 (4.57)
AC
0.22 (5.59)
0.18 (4.57)
Dimension in inches and (millimeter)
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Rating at 25 °C ambient temperature unless otherwise specified.
Single phase, half wave, 60 Hz, resistive or inductive load.
For capacitive load, derate current by 20%.
RATING
SYMBOL
FWL FWL
005G 01G
FWL
02G
FWL
04G
FWL
06G
FWL
08G
FWL
10G
UNIT
Maximum Recurrent Peak Reverse Voltage
VRRM
50
100
200
400
600
800
1000
Volts
Maximum RMS Voltage
VRMS
35
70
140
280
420
560
700
Volts
Maximum DC Blocking Voltage
VDC
50
100
200
400
600
800
1000
Volts
Maximum Average Forward Current
0.375" (9.5 mm) lead length
Tc = 50°C
IF(AV)
1.0
Amps.
IFSM
30
Amps.
2
It
10
A2S
VF
1.3
Volts
IR
10
µA
IR(H)
1.0
mA
Peak Forward Surge Current Single half sine wave
Superimposed on rated load (JEDEC Method)
Rating for fusing
( t < 8.3 ms. )
Maximum Forward Voltage per Diode at IF = 1.0 Amp.
Maximum DC Reverse Current
Ta = 25 °C
at Rated DC Blocking Voltage
Ta = 100 °C
Maximum Reverse Recovery Time (Note 1)
Trr
Typical Junction Capacitance per Diode (Note 2)
CJ
24
pf
RθJA
36
°C/W
TJ
- 50 to + 150
°C
TSTG
- 50 to + 150
°C
Typical Thermal Resistance (Note 3)
Operating Junction Temperature Range
Storage Temperature Range
Notes :
150
250
1 ) Measured with IF = 0.5 Amp., IR = 1 Amp., Irr = 0.25 Amp.
2 ) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts.
3 ) Thermal resistance from Junction to Ambient at 0.375" (9.5 mm) lead length P.C. Board mounting.
500
ns
UPDATE : APRIL 23,1998
RATING AND CHARACTERISTIC CURVES ( FWL005G - FWL10G )
FIG.1 - REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM
50 Ω
10 Ω
Trr
+ 0.5 A
D.U.T.
+
PULSE
GENERATOR
( NOTE 2 )
50 Vdc
(approx)
1Ω
0
- 0.25
OSCILLOSCOPE
( NOTE 1 )
- 1.0 A
SET TIME BASE FOR 50/100 ns/cm
NOTES : 1. Rise Time = 7 ns max., Input Impedance = 1 megaohm, 22 pF.
2. Rise time = 10 ns max., Source Impedance = 50 ohms.
1 cm
3. All Resistors = Non-inductive Types.
FIG.2 - DERATING CURVE FOR OUTPUT
RECTIFIED CURRENT
FIG.3 - MAXIMUM NON-REPETITIVE PEAK
FORWARD SURGE CURRENT
30
PC Board
0.375(9.5mm)
0.8
Copper Pads
0.22" x 0.22"
(5.5 x5.5mm)
0.6
0.4
0.2
60 Hz, Resistive or Inductive load.
0
0
25
50
75
100
125
150
PEAK FORWARD SURGE
CURRENT, AMPERES
AVERAGE FORWARD OUTPUT
CURRENT, AMPERES
1.0
24
18
12
SINGLE HALF SINE WAVE
(JEDEC METHOD)
6
0
175
TJ = 55 °C
1
CASE TEMPERATURE, ( °C)
20
10
1
TJ = 25 °C
Pulse Width = 300 µs
1 % Duty Cycle
0.01
0.4
0.8
1.2
1.6
2.0
2.4
2.8
FORWARD VOLTAGE, VOLTS
4
6
10
20
40
60
100
FIG.5 - TYPICAL REVERSE CHARACTERISTICS
REVERSE CURRENT, MICROAMPERES
FORWARD CURRENT, AMPERES
FIG.4 - TYPICAL FORWARD CHARACTERISTICS
0.1
2
NUMBER OF CYCLES AT 60Hz
3.2
10
TJ = 100 °C
1.0
TJ = 25 °C
0.1
0.01
0
20
40
60
80
100
120
PERCENT OF RATED REVERSE
VOLTAGE, (%)
140
Similar pages