MicroPower Direct Tightly Regulated, 1W Ultra-Miniature DIP DC/DC Converters G100R Series Key Features Miniature DIP Package !0.5% Line/Load Regulation 2.7 MH MTBF 1.0 kVDC Isolation 1W Output Power Low Cost Electrical Specifications Specifications typical @ +251C with nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Input Parameter Conditions Input Voltage Range Min. Typ. Max. 5 VDC Input 4.5 5.0 5.5 12 VDC Input 10.8 12.0 13.2 24 VDC Input 21.6 24.0 26.4 Typ. Max. Units !1.0 !5.0 % For Vin Change of Min to Max !0.5 % For Iout = 20% to 100% !0.5 % 50 mV P - P !0.02 %/1C Max. Units Input Filter Units VDC Internal Capacitor Output Parameter Conditions Min. Output Voltage Accuracy Line Regulation Load Regulation Ripple & Noise (20 MHz) Output Power Protection 120 % Temperature Coefficient !0.01 Output Short Circuit Momentary (0.5 Sec.) General Parameter Conditions Isolation Voltage Isolation Resistance Isolation Capacitance Min. 60 Seconds 1,000 500 VDC 1,000 Typ. VDC MΩ 100 kHz, 1V Switching Frequency 60 pF 80 kHz Environmental Parameter Conditions Operating Temperature Range Storage Temperature Range Min. Typ. Max. Units -40 +25 +85 1C +125 1C 95 % -40 Cooling Free Air Convection Humidity RH, Non-condensing Physical Case Size 0.80 x 0.40 x 0.27 Inches (20.32 x 10.16 x 6.85 mm) Case Material Non-Conductive Black Plastic Weight 0.09 Oz (2.7g) Reliability Specifications Parameter Conditions MTBF Min. Typ. Max. 2.7 MIL HDBK 217F, 251C, Gnd Benign Units MHours Absolute Maximum Ratings Parameter Conditions Input Voltage Surge (1 Sec) Internal Power Dissipation Min. Typ. Max. 5 VDC Input -0.7 6.0 12 VDC Input -0.7 14.0 24 VDC Input -0.7 28.0 All Models 450 Units VDC mW Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. MicroPower Direct TEL: (781) 344-8226 FAX: (781) 344-8481 E-Mail: [email protected] WEB: www/micropowerdirect.com Model Selection Guide Model Number G101R G102R G103R G104R G105R G111R G112R G113R G114R G115R G121R G122R G123R G124R G125R Input Voltage (VDC) Current (mA) Nominal Range Full-Load No-Load 5 4.5 - 5.5 213 28 5 4.5 - 5.5 317 28 5 4.5 - 5.5 312 26 5 4.5 - 5.5 312 26 5 4.5 - 5.5 312 38 12 10.8 - 13.2 91 16 12 10.8 - 13.2 130 16 12 10.8 - 13.2 130 16 12 10.8 - 13.2 130 16 12 10.8 - 13.2 130 16 24 21.6 - 26.4 43 7 24 21.6 - 26.4 64 7 24 21.6 - 26.4 65 9 24 21.6 - 26.4 65 9 24 21.6 - 26.4 65 9 Output Current (mA, Max) 200.0 200.0 111.0 83.0 66.0 200.0 200.0 111.0 83.0 66.0 200.0 200.0 111.0 83.0 66.0 Voltage (VDC) 3.3 5.0 9.0 12.0 15.0 3.3 5.0 9.0 12.0 15.0 3.3 5.0 9.0 12.0 15.0 Efficiency (%, Typ) Current (mA, Min) 20.0 20.0 11.0 9.0 7.0 20.0 20.0 11.0 9.0 7.0 20.0 20.0 11.0 9.0 7.0 62 63 64 64 66 61 64 64 64 64 63 65 64 64 64 Fuse Rating Slow-Blow (mA) 500 500 500 500 500 200 200 200 200 200 100 100 100 100 100 Derating Curve Notes: 1. These units do not require external comonents to operate, but the use of an input capacitor (10 µF) may enhance performance in some applications. An output capacitor (4.7 µF to 10 µF) may be used to reduce ripple. 100 Output Power % 80 60 40 20 0 -40 -20 0 5 15 25 35 45 55 65 75 85 95 105 Ambient Temperature 1C Capacitive Load Mechanical Dimensions µF Max 0.27 (6.85) Side 33 0.12 (3.05) Pin Connections Pin Single 1 -Vin 7 NC 9 +Vout 11 -Vout 14 +Vin 0.10 (2.54) 0.10 (2.54) 0.60 (15.24) 0.80 (20.32) 1 7 0.40 (10.2) Bottom NC = No Connection 14 Notes: All dimensions are typical in inches (mm) Tolerance x.xx = !0.01 (!0.25) Pin 1 is marked by a “dot” or indentation on the side of the unit MicroPower Direct 0.01 (0.25) 11 0.01 (0.25) 9 0.05 (1.25) 232 Tosca Drive, Stoughton, MA 02072 www.micropowerdirect.com [email protected] phone: (781) 344 - 8226 * fax: (781) 344 - 8481