STMicroelectronics GS-24S0501.8 1.8 a dc-dc converter module Datasheet

GS-R24FP
1.8 A DC-DC converter modules
Features
■
MTBF 1 000 000 hours (TA = 25 °C)
■
1.8 A max output current
■
35 V max input voltage
■
1.5 V max drop-out voltage
■
Remote logic inhibit/enable
■
Synchronization
■
Not-latching overload and short circuit
protection
■
Thermal shutdown
■
Fixed or adjustable output
■
No heatsink required
■
Operating temperature range -25 °C ÷ 85 °C
Packing type: V = vertical PTH
Description
The GS-R24FP series is a family of high
efficiency step down switching voltage regulator,
designed to replace linear regulators.
Based on ST L5973A device, this non isolated
family of regulators are suitable for the full
spectrum of applications including telecom,
industry, computer and distributed power system
applications having a widely ranging input
voltage.
Table 1.
Packing type: S = horizontal SMD
Device summary
Output voltage
Input voltage
Output ripple
Efficiency
[V]
[V]
[mVpp]
[%]
GS-R24FP0181.8
1.8 ± 4%
16 ÷ 35
25
59 - 63
Fixed output voltage
GS-R24FP0251.8
2.5 ± 4%
16 ÷ 35
30
66 - 70
Fixed output voltage
GS-R24FP0331.8
3.3 ± 4%
16 ÷ 35
30
70 - 75
Fixed output voltage
GS-R24FP0501.8
5.0 ± 4%
16 ÷ 35
40
79 - 83
Fixed output voltage
GS-R24FP0001.8
1.235 ÷ 5.5%
16 ÷ 35
40
56 - 83
Progr. output voltage
Order codes
February 2008
Rev 2
Notes
1/15
www.st.com
15
Contents
GS-R24FP
Contents
1
2
Pin settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1
Pin connection and mechanical data (dimensions in mm) . . . . . . . . . . . . . 3
1.2
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.1
Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.2
Thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.3
Thermal de-rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4
Application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5
4.1
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.2
Reference voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.3
Inhibit function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.4
Multiple units synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.5
Current limitation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.6
Thermal shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.7
Output voltage programming (GS-R24FP0001.8 only) . . . . . . . . . . . . . . . 9
4.8
Loop compensation (GS-R24FP0001.8 only) . . . . . . . . . . . . . . . . . . . . . . 9
4.9
Soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Additional features and protections . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.1
Output overvoltage protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
6
Ordering scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
7
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2/15
GS-R24FP
Pin settings
1
Pin settings
1.1
Pin connection and mechanical data (dimensions in mm)
Figure 1.
Pin connection GS-R24FVxxx1.8
Figure 2.
Pin connection GS-R24FSxxx1.8
3/15
Pin settings
1.2
GS-R24FP
Pin description
Table 2.
4/15
Pin description
Name
Function
Description
1
INH
A logic high level disables the device. When the pin is open, an
internal pull up disables the device
2
Sync
Master/slave synchronization
3
Vref
4
Input +
DC input voltage
5
Input +
DC input voltage
6
Input/output
GND
Return for input/output voltage source
7
Input/output
GND
Return for input/output voltage source
8
Vout
Regulated power output
9
Vout
Regulated power output
10
FB
Feedback input, available on adjustable device and on request for
additional compensation
3.3 V reference voltage
GS-R24FP
Maximum ratings
2
Maximum ratings
2.1
Absolute maximum ratings
Table 3.
Absolute maximum ratings
Symbol
2.2
Parameter
Value
Unit
36
V
VI
DC input voltage
Iout
Maximum output current
int. limit
V1
INH
-0.3 to Vi
V
V2
Sync
-0.3 to 4
V
V10
FB
4
V
Value
Unit
Thermal data
Table 4.
Symbol
Thermal data
Parameter
TSTG
Storage temperature range
-40 ÷ 105
°C
TOP
Operating ambient temperature
-25 ÷ 85
°C
5/15
Maximum ratings
2.3
Thermal de-rating
Table 5.
Symbol
Io
Io
Io
6/15
GS-R24FP
Thermal de-rating for free air condition (all versions)
Parameter
Output current
Output c urrent
Output current
Test condition
Value
VI = 16 V, TA = 30 °C
1.80
VI = 16 V, TA = 40 °C
1.80
VI = 16 V, TA = 50 °C
1.75
VI = 16 V, TA = 55 °C
1.70
VI = 16 V, TA = 60 °C
1.65
VI = 16 V, TA = 65 °C
1.50
VI = 16 V, TA = 70 °C
1.35
VI = 16 V, TA = 75 °C
1.25
VI = 16 V, TA = 80 °C
1.10
VI = 16 V, TA = 85 °C
0.90
VI = 24 V, TA = 30 °C
1.80
VI = 24 V, TA = 40 °C
1.75
VI = 24 V, TA = 50 °C
1.70
VI = 24 V, TA = 55 °C
1.60
VI = 24 V, TA = 60 °C
1.45
VI = 24 V, TA = 65 °C
1.30
VI = 24 V, TA = 70 °C
1.20
VI = 24 V, TA = 75 °C
1.05
VI = 24 V, TA = 80 °C
0.85
VI = 24 V, TA = 85 °C
0.60
VI = 35 V, TA = 30 °C
1.75
VI = 35 V, TA = 40 °C
1.60
VI = 35 V, TA = 50 °C
1.45
VI = 35 V, TA = 55 °C
1.35
VI = 35 V, TA = 60 °C
1.20
VI = 35 V, TA = 65 °C
1.05
VI = 35 V , TA = 70 °C
0.90
VI = 35 V, TA = 75 °C
0.75
VI = 35 V, TA = 80 °C
0.50
VI = 35 V, TA = 85 °C
0.30
Unit
A
A
A
GS-R24FP
3
Electrical characteristics
Electrical characteristics
TA = 25 °C, unless otherwise specified
Table 6.
Symbol
Electrical characteristics (all version)
Parameter
Test condition
Min
Typ
Max
Unit
30
60
mVpp
Ripple voltage
Vi =24 V Io = 1.8 A
for GS-R24FPyyy1.8
Temperature stability
Vi =Vo + 1.5 V Io = 1.8 A
Io
Output current
Vi =16 ÷ 35 V
for GS-R24FPyyy1.8
IoL
Current limit
Vi =16 ÷ 35 V
Iq
Quiescent current
Vi =24 V Io = 0 A
Iqst-by
Total stand-by
quiescent current
Vinh > 2.2 V Vi = 35 V
80
Switching frequency
Vi = 24 V Io = 1.8 A
500
Reference voltage
Vi = 16 ÷ 35 V Iref = 0 ÷ 5 mA
Vr
fs
Vref
Short circuit current
mV/°C
0
1.8
2.3
VFB
A
2.7
mA
150
µA
kHz
3.2
3.3
3.399
V
8
10
30
mA
0.8
V
Device ON
INH
A
INH threshold voltage
Feedback voltage
Device OFF
2.2
Vi =16 ÷ 35 V IO = 0 ÷ 1.8 A
1.22
V
1.235
1.25
V
7/15
Application information
4
Application information
4.1
Input voltage
GS-R24FP
The recommended maximum operating DC input voltage is 35 V including ripple voltage.
4.2
Reference voltage
No capacitor is required for stability.
4.3
Inhibit function
The inhibit feature allows to put the device in stand-by mode.
With INH pin 1 is higher than 2.2 V the device is disabled and the current consumption is
reduced to less than 150 µA for Vi = 35 V.
With INH pin lower than 0.8 V, the device is enabled.
If the INH pin is left floating, an internal pull up ensures that the voltage at the pin reaches
the inhibit threshold and the device is disabled.
The pin can be pulled to Vi to disable the device.
4.4
Multiple units synchronization
Using more than one unit on the same circuit, it is possible to synchronize the switching
frequency, connecting all pin 2 together (see Figure 6).
The unit with higher frequency becomes the master.
4.5
Current limitation
The device has two current limit protections, pulse by pulse and frequency fold back.
The current is sensed through a resistor and if it reaches the threshold, the on time is
reduced and consequently the output voltage, too.
Since the minimum switch ON time (necessary to avoid false overcurrent signal) is not
enough to obtain a sufficiently low duty cycle at 500 kHz, the output current could increase
again, in strong overcurrent or short circuit conditions.
For this reason the switching frequency is also reduced to keep the inductor current within
its maximum threshold limit.
The frequency depends on the feedback voltage.
As the feedback voltage decreases (due to the reduced duty cycle), the switching frequency
decrease too.
8/15
GS-R24FP
4.6
Application information
Thermal shutdown
The shutdown block generates a signal that turns OFF the power stage if the temperature of
the internal chip goes higher than a fixed internal threshold (150 °C min).
The sensing element of the chip is very close to the PDMOS area, so ensuring an accurate
and fast temperature detection.
An hysteresis of approximately 20 °C avoids that the devices turns ON and OFF
continuously.
4.7
Output voltage programming (GS-R24FP0001.8 only)
The GS-R24FP0001.8 output voltage is 5.54 V ± 4 %, to reduce this value connect a resistor
between pin 10 (FB) and pin 9 (Vout).
The resistor must be located very close to the proper pins, to minimize the injected noise
(see Figure 4).
The resistor value is calculated using the following formula:
for GS-R24FP0001.8 Rv = [(Vout - 1.235) * 11.3] / 5.54 - Vout) --[kΩ]
Vout can be adjusted between 1.235 V (Rv = 0 Ω) and 5.54V (Rv = open)
4.8
Loop compensation (GS-R24FP0001.8 only)
If required by particular load conditions, it is possible to change the feedback loop
compensation, adding an external capacitor between pin 10 (FB) and pin 9 (Vout), which will
act as speed up (see Figure 5).
9/15
Application information
4.9
GS-R24FP
Soldering
Soldering phase has to be execute with care : in order to avoid undesired melting
phenomenon, particular attention has to be take on the set up of the peak temperature.
Here following some suggestions for the temperature profile based on
IPC/JEDEC J-STD-020C ,July 2004 recommendations.
Table 7.
Soldering
Profile feature
Average ramp up rate ( TSMAX to TP)
3 °C / sec max
Preheat:
Temperature min ( TS MIN)
Temperature max ( TS MAX)
Time (TS MIN to TS MAX) ( tS )
150 °C
200 °C
60 – 100 sec
Time maintained above :
Temperature TL
Time tL
217 °C
40 – 70 sec
Peak temperature (TP)
240 + 0 °C
Time within 5 °C of actual peak temperature (tP)
10 – 20 sec
Ramp down rate
Time from 25 °C to peak temperature
Figure 3.
10/15
PB free assembly
Soldering
6 °C / sec
8 minutes max
GS-R24FP
Additional features and protections
5
Additional features and protections
5.1
Output overvoltage protection
The overvoltage protection, OVP, is realized by using an internal comparator, whose input is
connected to the feedback. It turns off the power stage when the OVP threshold is reached.
This threshold is typically 30 % higher than the feedback voltage.
Figure 4.
Output voltage programming
Figure 5.
10
4, 5
Loop compensation
4, 5
10
Rv
Rv
8, 9
Vin
GS-RxxFp000z.z
Vin
GS-RxxFp000z.z
Rload
Vout
Vout
Rload
6, 7
6, 7
Figure 6.
Cc
8, 9
Multiple units synchronization
2
4, 5
4, 5
2
Rload
8, 9
Vin
GS-RxxFpyyyz.z
6, 7
Vin
Vout
8, 9
Rload
GS-RxxFpyyyz.z
Vout
6, 7
11/15
Additional features and protections
Figure 7.
12/15
PCB footprint for GS-R24FSxxx1.8 (dimensions in mm)
GS-R24FP
GS-R24FP
6
Ordering scheme
Ordering scheme
Table 8.
Ordering information scheme
GS-
R12
FV
018
1.8
Input voltage
24 = 24 V
Package
V = Vertical
S = SMD
Output voltage
018 = 1.8 V
025 = 2.5 V
033 = 3.3 V
050 = 5.0 V
000 = 1.235 ÷ 5.5 V
Output current
1.8 = 1.8 A
13/15
Revision history
7
GS-R24FP
Revision history
Table 9.
14/15
Document revision history
Date
Revision
Changes
13-Oct-2006
1
Initial release
27-Feb-2008
2
Added: Section 4.9: Soldering on page 10
GS-R24FP
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2008 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
15/15
Similar pages