GSI GS82032AT-4

GS82032AT-180/166/150/133/100/66/4/5/6
180 MHz–66 MHz
3.3 V VDD
3.3 V and 2.5 V I/O
64K x 32
2Mb Synchronous Burst SRAM
TQFP
Commercial Temp
Industrial Temp
Features
• FT pin for user-configurable flow through or pipelined operation
• Single Cycle Deselect (SCD) operation
• 3.3 V +10%/–5% core power supply
• 2.5 V or 3.3 V I/O supply
• LBO pin for Linear or Interleaved Burst mode
• Internal input resistors on mode pins allow floating mode pins
• Default to Interleaved Pipelined mode
• Byte Write (BW) and/or Global Write (GW) operation
• Common data inputs and data outputs
• Clock Control, registered, address, data, and control
• Internal self-timed write cycle
• Automatic power-down for portable applications
• JEDEC standard 100-lead TQFP package
• Pb-Free 100-lead TQFP package available
Functional Description
Applications
The GS82032A is a 2,097,152-bit high performance
synchronous SRAM with a 2-bit burst address counter.
Although of a type originally developed for Level 2 Cache
applications supporting high performance CPUs, the device
now finds application in synchronous SRAM applications,
ranging from DSP main store to networking chip set support.
Controls
Addresses, data I/Os, chip enables (E1, E2, E3), address burst
control inputs (ADSP, ADSC, ADV), and write control inputs
(Bx, BW, GW) are synchronous and are controlled by a
positive-edge-triggered clock input (CK). Output enable (G)
and power down control (ZZ) are asynchronous inputs. Burst
cycles can be initiated with either ADSP or ADSC inputs. In
Burst mode, subsequent burst addresses are generated
internally and are controlled by ADV. The burst address
counter may be configured to count in either linear or
interleave order with the Linear Burst Order (LBO) input. The
Burst function need not be used. New addresses can be loaded
on every cycle with no degradation of chip performance.
Flow Through/Pipeline Reads
The function of the Data Output Register can be controlled by
the user via the FT mode pin (Pin 14 in the TQFP). Holding
the FT mode pin low places the RAM in Flow Through mode,
causing output data to bypass the Data Output Register.
Holding FT high places the RAM in Pipelined mode,
activating the rising-edge-triggered Data Output Register.
SCD Pipelined Reads
The GS82032A is an SCD (Single Cycle Deselect) pipelined
synchronous SRAM. DCD (Dual Cycle Deselect) versions are
also available. SCD SRAMs pipeline deselect commands one
stage less than read commands. SCD RAMs begin turning off
their outputs immediately after the deselect command has been
captured in the input registers.
Byte Write and Global Write
Byte write operation is performed by using Byte Write enable
(BW) input combined with one or more individual byte write
signals (Bx). In addition, Global Write (GW) is available for
writing all bytes at one time, regardless of the Byte Write
control inputs.
Sleep Mode
Low power (Sleep mode) is attained through the assertion
(High) of the ZZ signal, or by stopping the clock (CK).
Memory data is retained during Sleep mode.
Core and Interface Voltages
The GS82032A operates on a 3.3 V power supply and all
inputs/outputs are 3.3 V- and 2.5 V-compatible. Separate
output power (VDDQ) pins are used to decouple output noise
from the internal circuit.
Parameter Synopsis
Pipeline
3-1-1-1
Flow
Through
2-1-1-1
Rev: 1.12 10/2004
tCycle
tKQ
IDD
tCycle
tKQ
IDD
-180
5.5 ns
3.2 ns
155 mA
9.1 ns
8 ns
100 mA
-166
6 ns
3.5 ns
140 mA
10 ns
8.5 ns
90 mA
-150
6.6 ns
3.8 ns
130 mA
10.5 ns
9 ns
85 mA
-133 (-4)
7.5 ns
4 ns
115 mA
12 ns
10 ns
80 mA
-100 (-5)
10 ns
5 ns
90 mA
15 ns
12 ns
65 mA
1/22
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
-66 (-6)
12.5 ns
6 ns
65 mA
20 ns
18 ns
50 mA
© 2000, GSI Technology
GS82032AT-180/166/150/133/100/66/4/5/6
A
A
E1
E2
BD
BC
BB
BA
E3
VDD
VSS
CK
GW
BW
G
ADSC
ADSP
ADV
A
A
GS82032A 100-Pin TQFP Pinout
NC
DQC
DQC
VDDQ
NC
DQB
DQB
VDDQ
VSS
DQB
DQB
DQB
DQB
VSS
VDDQ
DQB
DQB
VSS
NC
VDD
ZZ
DQA
DQA
VDDQ
VSS
DQA
DQA
DQA
DQA
VSS
VDDQ
DQA
DQA
NC
LBO
A
A
A
A
A1
A0
NC
NC
VSS
VDD
NC
NC
A
A
A
A
A
A
NC
VSS
DQC
DQC
DQC
DQC
VSS
VDDQ
DQC
DQC
FT
VDD
NC
VSS
DQD
DQD
VDDQ
VSS
DQD
DQD
DQD
DQD
VSS
VDDQ
DQD
DQD
NC
100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81
1
80
2
79
3
78
4
77
5
76
6
75
7
74
8
73
9
72
64K x 32
10
71
Top View
11
70
12
69
13
68
14
67
15
66
16
65
17
64
18
63
19
62
20
61
21
60
22
59
23
58
24
57
25
56
26
55
27
54
28
53
29
52
30
51
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
Rev: 1.12 10/2004
2/22
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2000, GSI Technology
GS82032AT-180/166/150/133/100/66/4/5/6
TQFP Pin Description
Symbol
Type
Description
A 0, A 1
I
Address field LSBs and Address Counter preset Inputs
A
I
Address Inputs
DQA
DQB
DQC
DQD
I/O
Data Input and Output pins
NC
No Connect
BW
I
Byte Write—Writes all enabled bytes; active low
BA , BB
I
Byte Write Enable for DQA, DQB Data I/Os; active low
BC , BD
I
Byte Write Enable for DQC, DQD Data I/Os; active low
CK
I
Clock Input Signal; active high
GW
I
Global Write Enable—Writes all bytes; active low
E 1, E 3
I
Chip Enable; active low
E2
I
Chip Enable; active high
G
I
Output Enable; active low
ADV
I
Burst address counter advance enable; active low
ADSP, ADSC
I
Address Strobe (Processor, Cache Controller); active low
ZZ
I
Sleep Mode control; active high
FT
I
Flow Through or Pipeline mode; active low
LBO
I
Linear Burst Order mode; active low
VDD
I
Core power supply
VSS
I
I/O and Core Ground
VDDQ
I
Output driver power supply
Rev: 1.12 10/2004
3/22
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2000, GSI Technology
GS82032AT-180/166/150/133/100/66/4/5/6
GS82032A Block Diagram
A0–An
Register
D
Q
A0
A0
D0
A1
Q0
A1
D1
Q1
Counter
Load
A
LBO
ADV
Memory
Array
CK
ADSC
ADSP
Q
D
Register
GW
BW
BA
D
Q
Register
D
32
Q
BB
32
4
Register
D
Q
D
Q
D
Register
Q
Q
Register
D
Register
BC
BD
Register
D
Q
Register
E1
E2
E3
D
Q
Register
D
Q
FT
G
ZZ
Rev: 1.12 10/2004
Power Down
DQx1–DQx8
Control
4/22
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2000, GSI Technology
GS82032AT-180/166/150/133/100/66/4/5/6
Mode Pin Functions
Mode Name
Pin Name
Burst Order Control
LBO
Output Register Control
FT
Power Down Control
ZZ
State
Function
L
Linear Burst
H or NC
Interleaved Burst
L
Flow Through
H or NC
Pipeline
L or NC
Active
H
Standby, IDD = ISB
Note:
There are pull-up devices on LBO and FT pins and a pull-down device on the ZZ pin, so those input pins can be unconnected and the chip will
operate in the default states as specified in the above table.
Burst Counter Sequences
Linear Burst Sequence
A[1:0]
A[1:0]
A[1:0]
A[1:0]
1st address
00
01
10
11
2nd address
01
10
11
00
3rd address
10
11
00
01
4th address
11
00
01
10
Interleaved Burst Sequence
Note:
The burst counter wraps to initial state on the 5th clock.
Rev: 1.12 10/2004
A[1:0]
A[1:0]
A[1:0]
A[1:0]
1st address
00
01
10
11
2nd address
01
00
11
10
3rd address
10
11
00
01
4th address
11
10
01
00
Note:
The burst counter wraps to initial state on the 5th clock.
5/22
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2000, GSI Technology
GS82032AT-180/166/150/133/100/66/4/5/6
Byte Write Truth Table
Function
GW
BW
BA
BB
BC
BD
Notes
Read
H
H
X
X
X
X
1
Read
H
L
H
H
H
H
1
Write byte A
H
L
L
H
H
H
2, 3
Write byte B
H
L
H
L
H
H
2, 3
Write byte C
H
L
H
H
L
H
2, 3, 4
Write byte D
H
L
H
H
H
L
2, 3, 4
Write all bytes
H
L
L
L
L
L
2, 3, 4
Write all bytes
L
X
X
X
X
X
Notes:
1. All byte outputs are active in read cycles regardless of the state of Byte Write Enable inputs.
2. Byte Write Enable inputs BA, BB, BC and/or BD may be used in any combination with BW to write single or multiple bytes.
3. All byte I/Os remain High-Z during all write operations regardless of the state of Byte Write Enable inputs.
Rev: 1.12 10/2004
6/22
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2000, GSI Technology
GS82032AT-180/166/150/133/100/66/4/5/6
Synchronous Truth Table
Operation
Address
Used
State
Diagram
Key5
E1
E2
Deselect Cycle, Power Down
None
X
H
X
X
Deselect Cycle, Power Down
None
X
L
F
Deselect Cycle, Power Down
None
X
L
Read Cycle, Begin Burst
External
R
Read Cycle, Begin Burst
External
Write Cycle, Begin Burst
ADV
W3
DQ4
L
X
X
High-Z
L
X
X
X
High-Z
F
H
L
X
X
High-Z
L
T
L
X
X
X
Q
R
L
T
H
L
X
F
Q
External
W
L
T
H
L
X
T
D
Read Cycle, Continue Burst
Next
CR
X
X
H
H
L
F
Q
Read Cycle, Continue Burst
Next
CR
H
X
X
H
L
F
Q
Write Cycle, Continue Burst
Next
CW
X
X
H
H
L
T
D
Write Cycle, Continue Burst
Next
CW
H
X
X
H
L
T
D
Read Cycle, Suspend Burst
Current
X
X
H
H
H
F
Q
Read Cycle, Suspend Burst
Current
H
X
X
H
H
F
Q
Write Cycle, Suspend Burst
Current
X
X
H
H
H
T
D
ADSP ADSC
Write Cycle, Suspend Burst
Current
H
X
X
H
H
T
D
Notes:
1. X = Don’t Care, H = High, L = Low
2. E = T (True) if E2 = 1 and E3 = 0; E = F (False) if E2 = 0 or E3 = 1
3. W = T (True) and F (False) is defined in the Byte Write Truth Table preceding
4. G is an asynchronous input. G can be driven high at any time to disable active output drivers. G low can only enable active drivers (shown
as “Q” in the Truth Table above).
5. All input combinations shown above are tested and supported. Input combinations shown in gray boxes need not be used to accomplish
basic synchronous or synchronous burst operations and may be avoided for simplicity.
6. Tying ADSP high and ADSC low allows simple non-burst synchronous operations. See BOLD items above.
7. Tying ADSP high and ADV low while using ADSC to load new addresses allows simple burst operations. See ITALIC items above.
Rev: 1.12 10/2004
7/22
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2000, GSI Technology
GS82032AT-180/166/150/133/100/66/4/5/6
Simplified State Diagram
X
Deselect
W
R
Simple Burst Synchronous Operation
Simple Synchronous Operation
W
X
R
R
First Write
CW
First Read
CR
CR
W
X
R
R
X
Burst Write
Burst Read
X
CR
CW
CR
Notes:
1. The diagram shows only supported (tested) synchronous state transitions. The diagram presumes G is tied low.
2. The upper portion of the diagram assumes active use of only the Enable (E1, E2, E3) and Write (BA, BB, BC, BD, BW, and GW) control
inputs, and that ADSP is tied high and ADSC is tied low.
3. The upper and lower portions of the diagram together assume active use of only the Enable, Write, and ADSC control inputs, and
assumes ADSP is tied high and ADV is tied low.
Rev: 1.12 10/2004
8/22
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2000, GSI Technology
GS82032AT-180/166/150/133/100/66/4/5/6
Simplified State Diagram with G
X
Deselect
W
R
W
X
R
R
First Write
CR
CW
W
CW
W
X
First Read
X
CR
R
Burst Write
R
CR
CW
W
Burst Read
X
CW
CR
Notes:
1. The diagram shows supported (tested) synchronous state transitions, plus supported transitions that depend upon the use of G.
2. Use of “Dummy Reads” (Read Cycles with G high) may be used to make the transition from Read cycles to Write cycles without passing
through a Deselect cycle. Dummy Read cycles increment the address counter just like normal Read cycles.
3. Transitions shown in gray assume G has been pulsed high long enough to turn the RAM’s drivers off and for incoming data to meet Data
Input Set Up Time.
Rev: 1.12 10/2004
9/22
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2000, GSI Technology
GS82032AT-180/166/150/133/100/66/4/5/6
Absolute Maximum Ratings
(All voltages reference to VSS)
Symbol
Description
Value
Unit
VDD
Voltage on VDD Pins
–0.5 to 4.6
V
VDDQ
Voltage in VDDQ Pins
–0.5 to VDD
V
VCK
Voltage on Clock Input Pin
–0.5 to 6
V
VI/O
Voltage on I/O Pins
–0.5 to VDDQ+0.5 (≤ 4.6 V max.)
V
VIN
Voltage on Other Input Pins
–0.5 to VDD+0.5 (≤ 4.6 V max.)
V
IIN
Input Current on Any Pin
+/–20
mA
Output Current on Any I/O Pin
+/–20
mA
IOUT
PD
Package Power Dissipation
1.5
W
TSTG
Storage Temperature
–55 to 125
oC
TBIAS
Temperature Under Bias
–55 to 125
o
C
Note:
Permanent damage to the device may occur if the Absolute Maximum Ratings are exceeded. Operation should be restricted to Recommended
Operating Conditions. Exposure to conditions exceeding the Absolute Maximum Ratings, for an extended period of time, may affect reliability of
this component.
Recommended Operating Conditions
Parameter
Symbol
Min.
Typ.
Max.
Unit
Notes
Supply Voltage
VDD
3.135
3.3
3.6
V
1
I/O Supply Voltage
VDDQ
2.375
2.5
VDD
V
1
Input High Voltage
VIH
1.7
—
VDD+0.3
V
2
Input Low Voltage
VIL
–0.3
—
0.8
V
2
Ambient Temperature (Commercial Range Versions)
TA
0
25
70
°C
3
TA
–40
25
85
°C
3
Ambient Temperature (Industrial Range Versions)
Notes:
1. Unless otherwise noted, all performance specifications quoted are evaluated for worst case at both 2.75 V ≤ VDDQ ≤ 2.375 V (i.e., 2.5 V I/O)
and 3.6 V ≤ VDDQ ≤ 3.135 V (i.e., 3.3 V I/O) and quoted at whichever condition is worst case.
2. This device features input buffers compatible with both 3.3 V and 2.5 V I/O drivers.
3. Most speed grades and configurations of this device are offered in both Commercial and Industrial Temperature ranges. The part number of
Industrial Temperature Range versions end with the character “I”. Unless otherwise noted, all performance specifications quoted are evaluated for worst case in the temperature range marked on the device.
4. Input Under/overshoot voltage must be –2 V > Vi < VDD+2 V with a pulse width not to exceed 20% tKC.
Rev: 1.12 10/2004
10/22
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2000, GSI Technology
GS82032AT-180/166/150/133/100/66/4/5/6
Undershoot Measurement and Timing
Overshoot Measurement and Timing
VIH
20% tKC
VDD +- 2.0 V
VSS
50%
50%
VDD
VSS – 2.0 V
20% tKC
VIL
Capacitance
(TA = 25°C, f = 1 MHZ, VDD = 3.3 V)
Parameter
Symbol
Test conditions
Typ.
Max.
Unit
Control Input Capacitance
CI
VDD = 3.3 V
3
4
pF
Input Capacitance
CIN
VIN = 0 V
4
5
pF
COUT
VOUT = 0 V
6
7
pF
Output Capacitance
Note:
This parameter is sample tested.
AC Test Conditions
Parameter
Conditions
Input high level
2.3 V
Input low level
0.2 V
Input slew rate
1 V/ns
Input reference level
1.25 V
Output reference level
1.25 V
Output load
Fig. 1& 2
Notes:
1. Include scope and jig capacitance.
2. Test conditions as specified with output loading as shown in Fig. 1 unless otherwise noted.
3. Output Load 2 for tLZ, tHZ, tOLZ and tOHZ
4. Device is deselected as defined by the Truth Table.
Output Load 2
Output Load 1
DQ
2.5 V
50Ω
30pF*
225Ω
DQ
5pF*
VT = 1.25 V
225Ω
* Distributed Test Jig Capacitance
Rev: 1.12 10/2004
11/22
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2000, GSI Technology
GS82032AT-180/166/150/133/100/66/4/5/6
DC Electrical Characteristics
Parameter
Symbol
Test Conditions
Min
Max
IIL
VIN = 0 to VDD
–1 uA
1 uA
ZZ Input Current
IINZZ
VDD ≥ VIN ≥ VIH
0V ≤ VIN ≤ VIH
–1 uA
–1 uA
1 uA
300 uA
Mode Pin Input Current
IINM
VDD ≥ VIN ≥ VIL
0V ≤ VIN ≤ VIL
–300 uA
–1 uA
1 uA
1 uA
Output Leakage Current
IOL
Output Disable,
VOUT = 0 to VDD
–1 uA
1 uA
Output High Voltage
VOH
IOH = –4 mA, VDDQ = 2.375 V
1.7 V
Output High Voltage
VOH
IOH = –4 mA, VDDQ = 3.135 V
2.4 V
Output Low Voltage
VOL
IOL = 4 mA
Input Leakage Current
(except mode pins)
Rev: 1.12 10/2004
12/22
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
0.4 V
© 2000, GSI Technology
Rev: 1.12 10/2004
35
25
IDD
Flow Through
Device Deselected;
All other inputs
≥ VIH or ≤ VIL
Deselect
Current
IDD
Pipeline
ZZ ≥ VDD – 0.2 V
Standby
Current
10
100
IDD
Flow Through
ISB
Flow Through
155
IDD
Pipeline
Device Selected;
All other inputs
≥VIH or ≤ VIL
Output open
Operating
Current
0
to
70°C
Symbol
Test Conditions
Parameter
Operating Currents
-180
30
40
15
105
160
–40
to
85°C
25
30
10
90
140
0
to
70°C
30
35
15
95
145
–40
to
85°C
-166
25
30
10
85
130
0
to
70°C
30
35
15
90
135
–40
to
85°C
-150
20
30
10
80
115
0
to
70°C
25
35
15
85
120
–40
to
85°C
-133
20
25
10
65
90
0
to
70°C
25
30
15
70
95
–40
to
85°C
-100
20
25
10
50
65
0
to
70°C
25
30
15
55
70
–40
to
85°C
-66
mA
mA
mA
mA
mA
Unit
GS82032AT-180/166/150/133/100/66/4/5/6
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
13/22
© 2000, GSI Technology
GS82032AT-180/166/150/133/100/66/4/5/6
AC Electrical Characteristics
Pipeline
Flow
Through
Parameter
Symbol
Clock Cycle Time
-180
-166
-150
-133
-100
-66
Unit
Min
Max
Min
Max
Min
Max
Min
Max
Min
Max
Min
Max
tKC
5.5
—
6
—
6.6
—
7.5
—
10
—
12.5
—
ns
Clock to Output Valid
tKQ
—
3.2
—
3.5
—
3.8
—
4
—
5
—
6
ns
Clock to Output Invalid
tKQX
1.5
—
1.5
—
1.5
—
1.5
—
1.5
—
1.5
—
ns
Clock to Output in Low-Z
tLZ1
1.5
—
1.5
—
1.5
—
1.5
—
1.5
—
1.5
—
ns
Clock Cycle Time
tKC
9.1
—
10
—
10.5
—
12
—
15
—
20
—
ns
Clock to Output Valid
tKQ
—
8
—
8.5
—
9
—
10
—
12
—
18
ns
Clock to Output Invalid
tKQX
3
—
3
—
3
—
3
—
3
—
3
—
ns
Clock to Output in Low-Z
tLZ1
3
—
3
—
3
—
3
—
3
—
3
—
ns
Clock HIGH Time
tKH
1.3
—
1.3
—
1.3
—
1.3
—
1.3
—
1.3
—
ns
Clock LOW Time
tKL
1.5
—
1.5
—
1.5
—
1.5
—
1.5
—
1.5
—
ns
Clock to Output in High-Z
1
tHZ
1.5
3.2
1.5
3.5
1.5
3.8
1.5
4
1.5
5
1.5
6
ns
G to Output Valid
tOE
—
3.2
—
3.5
—
3.8
—
4
—
5
—
6
ns
G to output in Low-Z
tOLZ1
0
—
0
—
0
—
0
—
0
—
0
—
ns
G to output in High-Z
tOHZ1
—
3.2
—
3.5
—
3.8
—
4
—
5
—
6
ns
Setup time
tS
1.5
—
1.5
—
1.5
—
1.5
—
1.5
—
1.5
—
ns
Hold time
tH
0.5
—
0.5
—
0.5
—
0.5
—
0.5
—
0.5
—
ns
ZZ setup time
tZZS
2
5
—
5
—
5
—
5
—
5
—
5
—
ns
ZZ hold time
tZZH2
1
—
1
—
1
—
1
—
1
—
1
—
ns
ZZ recovery
tZZR
20
—
20
—
20
—
20
—
20
—
20
—
ns
Notes:
1. These parameters are sampled and are not 100% tested.
2. ZZ is an asynchronous signal. However, in order to be recognized on any given clock cycle, ZZ must meet the specified setup and hold
times as specified above.
Rev: 1.12 10/2004
14/22
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2000, GSI Technology
GS82032AT-180/166/150/133/100/66/4/5/6
Pipeline Mode Timing
Begin
Read A
Cont
Cont
Single Read
Deselect Write B
Read C
Read C+1 Read C+2 Read C+3 Cont
Single Write
tKL
tKH
tKC
Deselect
Burst Read
CK
ADSP
tS
tH
ADSC initiated read
ADSC
tS
tH
ADV
tS
tH
A0–An
A
B
C
tS
GW
tS
tH
BW
tH
tS
Ba–Bd
tS
Deselected with E1
tH
E1 masks ADSP
E1
tS
tH
E2 and E3 only sampled with ADSP and ADSC
E2
tS
tH
E3
G
tS
tOE
DQa–DQd
Rev: 1.12 10/2004
tOHZ
Q(A)
tKQ
tH
D(B)
tKQX
tLZ
tHZ
Q(C)
15/22
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Q(C+1)
Q(C+2)
Q(C+3)
© 2000, GSI Technology
GS82032AT-180/166/150/133/100/66/4/5/6
Flow Through Mode Timing
Begin
Read A
Cont
Cont
Write B
Read C
Read C+1 Read C+2 Read C+3 Read C
Cont
Deselect
tKL
tKH
tKC
CK
ADSP
Fixed High
tS
tH
tS
tH
ADSC
initiated read
ADSC
tS
tH
ADV
tS
tH
A0–An
A
B
C
tS
tH
GW
tS
tH
BW
tS
tH
Ba–Bd
tS
Deselected with E1
tH
E1
tS
tH
E2 and E3 only sampled with ADSC
E2
tS
tH
E3
G
tH
tS
tOE
DQa–DQd
Rev: 1.12 10/2004
tOHZ
Q(A)
D(B)
tKQ
tLZ
tHZ
tKQX
Q(C)
Q(C+1)
Q(C+2)
16/22
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Q(C+3)
Q(C)
© 2000, GSI Technology
GS82032AT-180/166/150/133/100/66/4/5/6
Sleep Mode Timing
tKH
tKC
tKL
CK
Setup
Hold
ADSP
ADSC
tZZR
tZZS
tZZH
ZZ
Application Tips
Single and Dual Cycle Deselect
SCD devices force the use of “dummy read cycles” (read cycles that are launched normally, but that are ended with the output
drivers inactive) in a fully synchronous environment. Dummy read cycles waste performance, but their use usually assures there
will be no bus contention in transitions from reads to writes or between banks of RAMs. DCD SRAMs do not waste bandwidth on
dummy cycles and are logically simpler to manage in a multiple bank application (wait states need not be inserted at bank address
boundary crossings), but greater care must be exercised to avoid excessive bus contention.
Rev: 1.12 10/2004
17/22
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2000, GSI Technology
GS82032AT-180/166/150/133/100/66/4/5/6
GS82032A Output Driver Characteristics
60
Pull Down Drivers
40
20
VDDQ
I Out
0
I Out (mA)
VOut
VSS
-20
-40
Pull Up Drivers
-60
-80
-0.5
0
0.5
1
1.5
2
2.5
3
3.5
4
V Out (Pull Dow n)
VDDQ - V Out (Pull Up)
3.6V PD LD
Rev: 1.12 10/2004
3.3V PD LD
3.1V PD LD
3.1V PU LD
3.3V PU LD
18/22
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
3.6V PU LD
© 2000, GSI Technology
GS82032AT-180/166/150/133/100/66/4/5/6
TQFP Package Drawing (Package T)
L
Min. Nom. Max
A1
Standoff
0.05
0.10
0.15
A2
Body Thickness
1.35
1.40
1.45
b
Lead Width
0.20
0.30
0.40
c
Lead Thickness
0.09
—
0.20
D
Terminal Dimension
21.9
22.0
22.1
D1
Package Body
19.9
20.0
20.1
E
Terminal Dimension
15.9
16.0
16.1
E1
Package Body
13.9
14.0
14.1
e
Lead Pitch
—
0.65
—
L
Foot Length
0.45
0.60
0.75
L1
Lead Length
—
1.00
—
Y
Coplanarity
θ
Lead Angle
L1
c
e
D
D1
Description
Pin 1
Symbol
θ
b
A1
A2
0.10
Y
0°
—
7°
E1
E
Notes:
1. All dimensions are in millimeters (mm).
2. Package width and length do not include mold protrusion.
Rev: 1.12 10/2004
19/22
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2000, GSI Technology
GS82032AT-180/166/150/133/100/66/4/5/6
Ordering Information for GSI Synchronous Burst RAMs
Speed2 TA
(MHz/ns) 3
Org
Part Number1
Type
Package
64K x 32
GS82032AT-180
Pipeline/Flow Through
TQFP
180/8
C
64K x 32
GS82032AT-166
Pipeline/Flow Through
TQFP
166/8.5
C
64K x 32
GS82032AT-150
Pipeline/Flow Through
TQFP
150/9
C
64K x 32
GS82032AT-133
Pipeline/Flow Through
TQFP
133/10
C
64K x 32
GS82032AT-100
Pipeline/Flow Through
TQFP
100/12
C
64K x 32
GS82032AT-66
Pipeline/Flow Through
TQFP
66/18
C
64K x 32
GS82032AT-4
Pipeline/Flow Through
TQFP
133/10
C
64K x 32
GS82032AT-5
Pipeline/Flow Through
TQFP
100/12
C
64K x 32
GS82032AT-6
Pipeline/Flow Through
TQFP
66/18
C
64K x 32
GS82032AT-180I
Pipeline/Flow Through
TQFP
180/8
I
64K x 32
GS82032AT-166I
Pipeline/Flow Through
TQFP
166/8.5
I
64K x 32
GS82032AT-150I
Pipeline/Flow Through
TQFP
150/9
I
64K x 32
GS82032AT-133I
Pipeline/Flow Through
TQFP
133/10
I
64K x 32
GS82032AT-100I
Pipeline/Flow Through
TQFP
100/12
I
64K x 32
GS82032AT-66I
Pipeline/Flow Through
TQFP
66/18
I
64K x 32
GS82032AT-4I
Pipeline/Flow Through
TQFP
133/10
I
64K x 32
GS82032AT-5I
Pipeline/Flow Through
TQFP
100/12
I
64K x 32
GS82032AT-6I
Pipeline/Flow Through
TQFP
66/18
I
64K x 32
GS82032AGT-180
Pipeline/Flow Through
Pb-free TQFP
180/8
C
64K x 32
GS82032AGT-166
Pipeline/Flow Through
Pb-free TQFP
166/8.5
C
64K x 32
GS82032AGT-150
Pipeline/Flow Through
Pb-free TQFP
150/9
C
64K x 32
GS82032AGT-133
Pipeline/Flow Through
Pb-free TQFP
133/10
C
64K x 32
GS82032AGT-100
Pipeline/Flow Through
Pb-free TQFP
100/12
C
64K x 32
GS82032AGT-66
Pipeline/Flow Through
Pb-free TQFP
66/18
C
64K x 32
GS82032AGT-4
Pipeline/Flow Through
Pb-free TQFP
133/10
C
64K x 32
GS82032AGT-5
Pipeline/Flow Through
Pb-free TQFP
100/12
C
64K x 32
GS82032AGT-6
Pipeline/Flow Through
Pb-free TQFP
66/18
C
64K x 32
GS82032AGT-180I
Pipeline/Flow Through
Pb-free TQFP
180/8
I
64K x 32
GS82032AGT-166I
Pipeline/Flow Through
Pb-free TQFP
166/8.5
I
Status
64K x 32 GS82032AGT-150I
Pipeline/Flow Through
Pb-free TQFP
150/9
I
Notes:
1. Customers requiring delivery in Tape and Reel should add the character “T” to the end of the part number. Example: GS82032AT-150IT.
2. The speed column indicates the cycle frequency (MHz) of the device in Pipelined mode and the latency (ns) in Flow Through mode. Each
device is Pipeline/Flow Through mode-selectable by the user.
3. TA = C = Commercial Temperature Range. TA = I = Industrial Temperature Range.
4. GSI offers other versions this type of device in many different configurations and with a variety of different features, only some of which are
covered in this data sheet. See the GSI Technology web site (www.gsitechnology.com) for a complete listing of current offerings.
Rev: 1.12 10/2004
20/22
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2000, GSI Technology
GS82032AT-180/166/150/133/100/66/4/5/6
Ordering Information for GSI Synchronous Burst RAMs
Speed2 TA
(MHz/ns) 3
Org
Part Number1
Type
Package
64K x 32
GS82032AGT-133I
Pipeline/Flow Through
Pb-free TQFP
133/10
I
64K x 32
GS82032AGT-100I
Pipeline/Flow Through
Pb-free TQFP
100/12
I
64K x 32
GS82032AGT-66I
Pipeline/Flow Through
Pb-free TQFP
66/18
I
64K x 32
GS82032AGT-4I
Pipeline/Flow Through
Pb-free TQFP
133/10
I
64K x 32
GS82032AGT-5I
Pipeline/Flow Through
Pb-free TQFP
100/12
I
Status
64K x 32
GS82032AGT-6I
Pipeline/Flow Through
Pb-free TQFP
66/18
I
Notes:
1. Customers requiring delivery in Tape and Reel should add the character “T” to the end of the part number. Example: GS82032AT-150IT.
2. The speed column indicates the cycle frequency (MHz) of the device in Pipelined mode and the latency (ns) in Flow Through mode. Each
device is Pipeline/Flow Through mode-selectable by the user.
3. TA = C = Commercial Temperature Range. TA = I = Industrial Temperature Range.
4. GSI offers other versions this type of device in many different configurations and with a variety of different features, only some of which are
covered in this data sheet. See the GSI Technology web site (www.gsitechnology.com) for a complete listing of current offerings.
Rev: 1.12 10/2004
21/22
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2000, GSI Technology
GS82032AT-180/166/150/133/100/66/4/5/6
Revision History
DS/DateRev. Code: Old;
New
Types of Changes
Revisions
Format or Content
GS82032 Rev 1.03 2/
2000D;GS820321.04 3/
2000E
Content
GS820321.04 3/2000E;
GS82032A_r1_05
Content
• First Release of A version. Added “A” Version to 82032T/Q,
820E32TQ, and 820H32TQ
• Updated ADSC in timing diagrams on pages 16 and 18
Content
• Added 200 MHz, 180 MHz, and 166 MHz speed bins (all references updated)
• Deleted 150 MHz, 138 MHz, and 66 MHz speed bins (all references deleted)
• Deleted BGA reference in “Flow Through/Pipeline Reads” on
page 1
• Updated entire datasheet with new standards
Content
• Updated table on page 1
• Updated Operating Currents table on page 12
• Updated Electrical Characteristics table on page 13
• Updated format to comply with Technical Publications standards
82032A_r1_07;
82032A_r1_08
Content
• Added the following part numbers to the Ordering Information
table on page 22:
– GS82032AT-4
– GS82032AT-6
– GS82032AT-4I
– GS82032AT-6I
– GS82032AQ-4
– GS82032AQ-6
– GS82032AQ-4I
– GS82032AQ-6I
82032A_r1_08;
82032A_r1_09
Content
82032A_r1_09;
82032A_r1_10
Content
• Complete rewrite of datasheet in order to reflect parts
available
82032A_r1_10;
82032A_r1_11
Content
• Reactiviated 180 MHz speed bin
• Updated format
82032A_r1_11;
82032A_r1_12
Content
82032A_r1_05;
82032A_r1_06
82032A_r1_06;
82032A_r1_07
Rev: 1.12 10/2004
• Removed all references to 200 MHz parts (no longer active)
• Added Pb-free information for TQFP
22/22
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2000, GSI Technology