ETC2 HB15SKW01-6F-CB Subminiature pushbutton Datasheet

Toggles
Series HB
Rockers
General Specifications
Electrical Capacity (Resistive Load)
Other Ratings
Contact Resistance:
Insulation Resistance:
Dielectric Strength:
Mechanical Life:
Electrical Life:
Nominal Operating Force:
Contact Timing:
Travel:
D
Materials & Finishes
Housing:
Base:
Movable Contact:
Stationary Contacts:
Common Terminal:
End Terminals:
Lamp Terminals:
Tactiles
Slides
Rotaries
Keylocks
Programmable Illuminated PB
Pushbuttons
Power Level (silver):
Environmental Data
Operating Temperature Range:
Humidity:
Vibration:
Shock:
Installation
Touch
Tilt
Mounting Torque:
Cap Installation Force:
Soldering Time & Temperature:
Standards & Certifications
UL:
0.1A maximum @ 30V AC/DC
50 milliohms maximum
100 megohms minimum @ 500V DC
500V AC minimum for 1 minute minimum
100,000 operations minimum
50,000 operations minimum
3.43N
Nonshorting (break before make)
Pretravel .087” (2.2mm); Overtravel .031” (0.8mm); Total Travel .118” (3.0mm)
Glass fiber reinforced polyamide
Glass fiber reinforced polyamide
Phosphor bronze with silver plating
Phosphor bronze with silver plating
Phosphor bronze with silver plating
Phosphor bronze with silver plating
Phosphor bronze with silver plating
–25°C through +50°C (–13°F through +122°F) for Illuminated
–25°C through +70°C (–13°F through +158°F) for Nonilluminated
90 ~ 95% humidity for 96 hours @ 40°C (104°F)
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning
in 1 minute; 3 right angled directions for 2 hours
50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
0.49Nm (4.34 lb • in) maximum for round mounting nut
9.8N (2.2 lbf) maximum downward force on cap
Manual Soldering: See Profile A in Supplement section.
File No. E44145 - Recognized only when ordered with marking on switch.
Add “/U” or “/CUL” before first dash in part number to order UL recognized switch.
All models recognized at 0.1A @ 30V AC/DC.
Supplement
Accessories
Indicators
Subminiature Pushbuttons
D12
www.nkk.com
Toggles
Series HB
Subminiature Pushbuttons
Rockers
Distinctive Characteristics
Choice of super bright LEDs in white, green, and blue in
addition to bright red, amber, and green LEDs.
Compact front panel design with 9mm square or round
bezel options.
D
Keylocks
Rear panel threaded mounting. Behind panel depth of
less than one inch. 8mm body diameter fits common
size panel cutout.
Programmable Illuminated PB
Pushbuttons
Full face and spot illumination available. Front panel relamping.
Latchdown feature gives indication of circuit status. Audible
and tactile feedback with smooth and responsive operation.
Rotaries
Dual, sliding contacts with self-cleaning action provide
contact stability, high reliability, and increased operating life.
Slides
Solder lug terminals have spacing of .100” (2.54mm) for choice
of mounting.
Tactiles
Longer normally closed terminal facilitates wiring and soldering.
Molded-in terminals lock out flux, dust, and other contaminants.
Touch
Tilt
Matching indicators available.
Supplement
Accessories
Indicators
Actual Size
www.nkk.com
D13
Series HB
Toggles
Subminiature Pushbuttons
TYPICAL SWITCH ORDERING EXAMPLE
5
1
SPDT
S
K
W01
Shapes
Contacts & Terminals
S
Square
C
Round
Silver Contacts and
W01 Solder Lug Terminals*
0.1A @ 30V AC/DC
6G
JB
D
Housing
Circuits
5
ON
K
(ON)
Black only
( ) = Momentary
6
ON
ON
Alternate Action
with Latchdown
* Wire harness & cable assemblies offered only in Americas
Tactiles
IMPORTANT:
Tilt
Cap Types & Colors
Bright
LED Cap: Lens/Diffuser Color
5C
Red
5D
Amber
5F
Green
AB
Black Cap/White Window for
Spot Illuminated (Square only)
CB
Red/White
DB
Amber/White
FB
Green/White
JB
Clear/White
6B
White
6F
Green
6G
Blue
LED Cap: Lens/Diffuser Color
JB
Nonilluminated
Switches are supplied without UL &
cULus marking unless specified.
UL & cULus recognized only when
ordered with marking on the switch.
Specific models, ratings, & ordering instructions are noted on General Specifications page.
Touch
LEDs
Super Bright
Slides
Rotaries
1
Pole
Keylocks
Programmable Illuminated PB
Pushbuttons
Rockers
HB
No
Nonilluminated
Code
Clear/White
Nonilluminated Cap Colors
A
Black (Square Only)
B
White
C
Red
E
Yellow
F
Green
G
Blue
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
Indicators
HB15SKW01-6G-JB
Blue, Super Bright LED
White Cap
Accessories
Square Shape
Black Housing
SPDT
ON-(ON) Circuit
Supplement
Silver Contacts &
Solder Lug Terminals;
rated 0.1A @ 30V AC/DC
D14
www.nkk.com
Series HB
Toggles
Subminiature Pushbuttons
POLES & CIRCUITS
SP
HB15
*HB16
Normal
Down
Normal
Down
Notes:
ON
ON
(ON)
ON
1-3
1-2
SPDT
Rockers
Model
Throw & Switch/Lamp Schematics
Switch is marked with NO, NC, C, L.
LED circuit is isolated and requires
external power source.
Pushbuttons
Pole
Connected Terminals
1 (COM)
(+)
3
(-)
2
* When in latchdown position for the alternate circuit, cap position is .051” (1.3mm) above the built-in bezel.
D
SHAPES & PANEL CUTOUT
C
.354” (9.0mm) Square
.354” (9.0mm) Round
Keylocks
S
Programmable Illuminated PB
Plunger Position
( ) = Momentary
Rotaries
The bezel is an integral
part of the switch body.
The bezel is an integral
part of the switch body.
Slides
Panel Cutout & Mounting
(8.0) Dia
.315
Overtightening the mounting nut AT073
may damage the switch housing.
Tactiles
Recommended Panel Thickness:
.020 ~ .197” (0.5 ~ 5.0mm)
Tilt
HOUSING
Housing available in black only.
Touch
K
Silver Contacts
Power Level
PCB Mounting
(5.0)
.197
(2.0)
.079
(1.0)
.039
(1.8)
.071
Thk = (0.3)
.012
Accessories
Solder Lug
0.1A maximum @ 30V AC/DC
Solder lug terminals are spaced
.100” x .200” (2.54mm x 5.08mm).
This enables PCB mounting which can be
accomplished by elongating PC board
holes to .080” (2.03mm).
www.nkk.com
Supplement
W01
Indicators
CONTACT MATERIALS, RATINGS, & TERMINALS
D15
Series HB
Toggles
Subminiature Pushbuttons
LED COLORS & SPECIFICATIONS
Rockers
The electrical specifications shown are determined at a basic temperature of 25°C.
LED circuit is isolated and requires external power source. Single element LED is colored in OFF state.
If the source voltage exceeds the rated voltage, a ballast resistor is required.
The resistor value can be calculated by using the formula in the Supplement section.
Slides
Rotaries
Keylocks
Programmable Illuminated PB
Pushbuttons
Bright
AT633
D
AT630F
Green
5F
6B
6F
6G
Color
Red
Amber
Green
White
Green
Blue
Unit
Forward Peak Current
I FM
30
30
25
30
30
30
mA
Typical Forward Current
IF
20
20
20
20
20
20
mA
Forward Voltage
VF
1.85
2.0
2.2
3.6
3.5
3.6
V
Reverse Peak Voltage
VRM
5
5
5
5
5
5
V
Current Reduction Rate Above 25°C
∆I F
0.40
0.42
0.38
0.50
0.50
0.50
mA/°C
No Code
(-)
Ambient Temperature Range
T-1 Bi-pin
–25° ~ +50°C
–25° ~ +50°C
No Lamp
CAP TYPES & COLORS
Color Codes:
A Black
B White
AB
CB
Black Cap with Translucent
White Window for LED Display
Amber/White
FB
Green/White
D Amber
E Yellow
F Green
AT4166
Square
AT4052
Spot Illuminated
AT4167
Round
(7.4) Sq
.291
G Blue
(7.4) Sq
.291
Square only
Material: Polycarbonate
Finish: Matte
Red/White
DB
Tilt
C Red
Colored Cap for Bright LEDs
Cap Colors Available:
Lens/Diffuser
Colors Available:
Tactiles
Super Bright
5D
(+)
AT629B
White
ELECTROSTATIC
SENSITIVE DEVICES
5C
Super Bright
AT624G
Blue
Bright
ATTENTION
Note for Super Bright:
(4.8)
.189
Translucent
White Diffuser
(4.8)
.189
Colored LED
AT633
Finish: Glossy
Transparent Clear
Lens
White Cap for Bright & Super Bright LEDs
Supplement
Accessories
Indicators
Touch
JB
Clear Lens/
White Diffuser
AT4031
Square
(7.4) Sq
.291
AT4032
Round
(4.8)
.189
Finish: Glossy
Translucent
White Diffuser
(7.4) Dia
.291
(4.5)
.177
Material: Polycarbonate
(1.2)
.047
(3.0)
.118
Transparent Colored
Lens
(4.5)
.177
Material: Polycarbonate
(1.8)
.071
(4.6)
.181
(7.4) Dia
.291
(4.5)
.177
(4.8)
.189
J Clear
(4.5)
.177
Colored LEDs
AT624, AT629,
AT630, or AT633
(4.8)
.189
Nonilluminated Caps
Cap Colors Available:
A
B
Black
(Square Only)
White
Material: Polycarbonate
D16
C
E
Red
Yellow
F
G
Green
Blue
Finish: Glossy
www.nkk.com
AT4035
Square
(7.4) Sq
.291
AT4036
Round
(4.5)
.177
(4.8)
.189
(7.4) Dia
.291
(4.5)
.177
(4.8)
.189
Series HB
Toggles
Subminiature Pushbuttons
TYPICAL SWITCH DIMENSIONS
Square
L(+) L(-)
NC
1
(5.0)
.197
(7.0)
.276
(2.54) Typ
.100
Latchdown Position
HB15SKW01-5C-CB
Single Pole
(1.0) x (2.0) Typ
.039 x .079
(0.3) Typ
.012
L(+) L(-)
NC
(7.4) Dia
.291
(9.0) Dia
.354
(1.3)
.051
(3.5)
.138
(5.0)
(0.5)
.197
.020
(10.0)
.394
(5.3)
(15.5)
.209
.610
COM
(1.8)
.071
(2.54) Typ
.100
2
3
1
(5.0)
.197
(7.0)
.276
Keylocks
NO
(2.54) Typ
.100
Latchdown Position
HB16CKW01-5C-CB
Slides
ASSEMBLY INSTRUCTIONS
Cap Removal
LED Polarity & Orientation in Lamp Socket
Cap Replacement
1. Have cap in extended
position (not latchdown) for
alternate action models.
For AT624, AT629, AT630: Insert the LED with the
D flat opposite the black dot molded inside the
switch lamp socket. For AT633: Insert the LED with
the Black Dot on the terminal to the right.
1. Match the prongs on
the cap base with the
projections in the switch,
at the same time aligning
the spring clips on the
cap with the indentations
in the switch.
Black Dot
D Flat
(+)
AT624
AT629
AT630
(–)
(+)
(–)
AT633
2. Press firmly in place.
Indicators
ATTENTION
ELECTROSTATIC
SENSITIVE DEVICES
Cathode
(–)
Super Bright LEDs AT624, AT629,
& AT630 are electrostatic sensitive.
AT111 Lamping Tool
AT110 Socket Wrench
Lamping Tool AT111 may be
used to remove and replace LED.
Socket Wrench AT110 may be
used to tighten the mounting nut.
www.nkk.com
Accessories
Anode
(+)
Touch
Top View
of Switch
Supplement
2. Use the grip slots on the
sides of the cap and pull it
out of the switch.
Rotaries
M8P0.75
Round
D
Tactiles
(1.3)
.051
(3.5)
.138
(0.5)
(5.0)
.020
.197
(10.0)
.394
(15.5)
(5.3)
.610
.209
3
Tilt
(7.4) Sq
.291
(9.0) Sq
.354
COM
(1.8)
.071
(2.54) Typ
.100
2
Pushbuttons
NO
Programmable Illuminated PB
(1.0) x (2.0) Typ
.039 x .079
(0.3) Typ
.012
M8P0.75
Rockers
Single Pole
D17
Similar pages