HCC/HCF4094B 8–STAGE SHIFT-AND-STORE BUS REGISTER . . .. . .. .. 3-STATE PARALLEL OUTPUTS FOR CONNECTION TO COMMON BUS SEPARATE SERIAL OUTPUTS SYNCHRONOUS TO BOTH POSITIVE AND NEGATIVE CLOCK EDGES FOR CASCADING MEDIUM SPEED OPERATION 5MHz AT 10V STANDARDIZED SYMMETRICAL OUTPUT CHARACTERISTICS QUIESCENT CURRENT SPECIFIED TO 20V FOR HCC DEVICE 5V, 10V, AND 15V PARAMETRIC RATINGS INPUT CURRENT OF 100nA AT 18V AND 25°C FOR HCC DEVICE 100% TESTED FOR QUIESCENT CURRENT MEETS ALL REQUIREMENTS OF JEDEC TENTATIVE STANDARD N°. 13A, ”STANDARD SPECIFICATIONS FOR DESCRIPTION OF ”B” SERIES CMOS DEVICES” EY (Plastic Package) M1 (Micro Package) F (Ceramic Frit Seal Package) C1 (Plastic Chip Carrier) ORDER CODES : HCC4094BF HCF4094BM1 HCF4094BEY HCF4094BC1 PIN CONNECTIONS DESCRIPTION The HCC4094B (extended temperature range) and HCF4094B (intermediate temperature range) are monolithic integrated circuits available in 16-lead dual in-line plastic or ceramic packageand plastic micropackage. The HCC/HCF4094B is an 8-stage serial shift register having a storage latch associated with each stage for strobing data from the serial input to parallel buffered 3-state outputs. The parallel outputs may be connected directly to common bus lines. Data is shifted on positive clock transitions. The data in each shift register stage is transferred to the storage register when the STROBE input is high. Data in the storage register appears at the outputs whenever the OUTPUT-ENABLE signal is high. Two serial outputs are available for cascading a number of HCC/HCF4094B devices. Data is available at the QS serial output terminal on positive clock edges to allow for high-speed operation in cascaded systems in which the clock rise time is fast. The same serial information, available at the Q’S terminal on the next negative clock edge, provides a means for cascading HCC/HCF4094B devices when the clock rise time is slow. June 1989 1/14 HCC/HCF4094B FUNCTIONAL DIAGRAM ABSOLUTE MAXIMUM RATINGS Symbol V DD * Parameter Supply Voltage : H CC Types H C F Types Value Unit – 0.5 to + 20 – 0.5 to + 18 V V Vi Input Voltage – 0.5 to V DD + 0.5 V II DC Input Current (any one input) ± 10 mA Total Power Dissipation (per package) Dissipation per Output Transistor for T o p = Full Package-temperature Range 200 mW 100 mW Pt o t Top Operating Temperature : HCC Types H CF Types – 55 to + 125 – 40 to + 85 °C °C T st g Storage Temperature – 65 to + 150 °C Stresses above those listed under ”Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for external periods may affect device reliability. * All voltage values are referred to VSS pin voltage. RECOMMENDED OPERATING CONDITIONS Symbol V DD VI Top 2/14 Parameter Supply Voltage : HC C Types H CF Types Input Voltage Operating Temperature : HCC Types H CF Types Value Unit 3 to 18 3 to 15 V V 0 to V DD V – 55 to + 125 – 40 to + 85 °C °C HCC/HCF4094B LOGIC DIAGRAMS TIMING DIAGRAM 3/14 HCC/HCF4094B TRUTH TABLE TRUTH TABLE CL ∆ – –/ –\ – – / – – –/ – –/ –\ – Outputs Enable Strobe 0 X 0 D ata Parallel Outputs Serial Outputs Q1 QN QS* Q’S X OC OC Q7 NC X X OC OC NC Q7 1 0 X NC NC Q7 NC 1 1 0 0 Q N-1 Q7 NC 1 1 1 1 Q N-1 Q7 NC 1 1 1 NC NC NC Q7 ▲ = Level Change Logic 1 ≡ High X = Don’t Care Logic 0 ≡ Low NC = No Change OC = Open Circuit * At the positive clock edge information in the 7th shift register stage is transferred to the 8th register stage and the QS output. 4/14 HCC/HCF4094B STATIC ELECTRICAL CHARACTERISTICS (over recommended operating conditions) Symbol IL Parameter Quiescent Current HCC Types HCF Types V OH V OL V IH V IL I OH Output High Voltage Output Low Voltage Input High Voltage Input Low Voltage Output Drive Current HCC Types HCF Types I OL Output Sink Current HCC Types HCF Types I IH , I IL I OH , I O L CI Input Leakage Current HCC Types HCF Types 3-state HCC Output Types Leakage HCF Current Types Input Capacitance Test Conditions VO |I O | V D D VI (V) (V) (µA) (V) 0/ 5 5 0/10 10 0/15 15 0/20 20 0/ 5 5 0/10 10 0/15 15 0/ 5 <1 5 0/10 <1 10 0/15 <1 15 5/0 <1 5 10/0 <1 10 15/0 <1 15 0.5/4.5 < 1 5 1/9 <1 10 1.5/13.5 < 1 15 4.5/0.5 < 1 5 9/1 <1 10 13.5/1.5 < 1 15 0/ 5 2.5 5 0/ 5 4.6 5 0/10 9.5 10 0/15 13.5 15 0/ 5 2.5 5 0/ 5 4.6 5 0/10 9.5 10 0/15 13.5 15 0/ 5 0.4 5 0/10 0.5 10 0/15 1.5 15 0/ 5 0.4 5 0/10 0.5 10 0/15 1.5 15 0/18 T L o w* Min. Max. 5 10 20 100 20 40 80 4.95 9.95 14.95 0.05 0.05 0.05 3.5 7 11 1.5 3 4 – 2 – 0.64 – 1.6 – 4.2 – 1.53 – 0.52 – 1.3 – 3.6 0.64 1.6 4.2 0.52 1.3 3.6 Value 25 °C Min. Typ. Max. 0.04 5 0.04 10 0.04 20 0.08 100 0.04 20 0.04 40 0.04 80 4.95 9.95 14.95 0.05 0.05 0.05 3.5 7 11 1.5 3 4 – 1.6 – 3.2 – 0.51 – 1 – 1.3 – 2.6 – 3.4 – 6.8 – 1.36 – 3.2 – 0.44 – 1 – 1.1 – 2.6 – 3.0 – 6.8 0.51 1 1.3 2.6 3.4 6.8 0.44 1 1.1 2.6 3.0 6.8 18 ± 0.1 ±10 – 5 ± 0.1 ± 1 15 ± 0.3 ±10 – 5 ± 0.3 ±1 T Hi g h * Min. Max. 150 300 600 3000 150 300 600 4.95 9.95 14.95 0.05 0.05 0.05 3.5 7 11 1.5 3 4 – 1.15 – 0.36 – 0.9 – 2.4 – 1.1 – 0.36 – 0.9 – 2.4 0.36 0.9 2.4 0.36 0.9 2.4 0/18 0/18 18 ± 0.4 ± 10-4 ± 0.4 ± 12 0/15 0/15 15 ± 1.0 ± 10- 4 ± 1.0 ± 7.5 Any Input µA V V V V mA mA µA Any Input 0/15 Unit 5 7.5 µA pF * TLow = – 55°C for HCC device : – 40°C for HCF device. * THigh = + 125°C for HCC device : + 85°C for HCF device. The Noise Margin for both ”1” and ”0” level is : 1V min. with VDD = 5V, 2V min. with VDD = 10V, 2.5V min. with VDD = 15V. 5/14 HCC/HCF4094B DYNAMIC ELECTRICAL CHARACTERISTICS (T amb = 25°C, CL = 50pF, R L = 200kΩ, typical temperature coefficient for all V DD = 0.3%/°C values , all input rise and fall time = 20ns) Symbol Parameter t P L H , t P HL Propagation Delay Time Clock to Serial Output Q S t P L H , t P HL Propagation Delay Time Clock to Serial Output Q’S t P L H , t P HL Propagation Delay Time Clock to Parallel Output t P L H , t P HL Propagation Delay Time Strobe to Parallel Output t P HZ t PL Z tW tW t se t u p t TL H, t T HL t r, tf f max 6/14 Propagation Delay Time Output Enable to Parallel Output : Output High to High Impedance Out Low to High Impedance Strobe Pulse Width Clock Pulse Width Data Setup Time Transition Time Clock Input Rise or Fall Time Maximum Clock Input Frequency Test Conditions Value V D D (V) Min. Typ. Max. 5 300 600 10 125 250 15 95 190 5 230 460 10 110 220 15 75 150 5 420 840 10 195 390 15 135 270 5 290 580 10 145 290 15 100 200 5 140 280 10 75 150 15 55 110 5 225 450 10 95 190 15 70 140 5 200 100 10 80 40 15 70 35 5 200 100 10 100 50 15 83 40 5 125 60 10 55 30 15 35 20 200 50 100 15 40 80 5 ns ns ns ns ns 100 15 ns ns 5 5 ns ns 10 10 Unit ns µs 15 5 5 1.25 2.5 10 2.5 5 15 3 6 MHz HCC/HCF4094B Typical Output Low (sink) Current Characteristics. Minimum Output Low (sink) Current Characteristics. Typical Output High (source) Current Charateristics. Minimum Output High (source) Current Characteristics. Clock-to-serial Output Q S Propagation Delay vs. CL. Clock-to-serial Output Q’S Propagation Delay vs. CL. 7/14 HCC/HCF4094B Clock-to-parallel Output Propagation Delay vs. CL. Strobe-to-parallel Output Propagation Delay vs. CL. Output Enable-to-parallel Output Propagation Delay vs. Typical Transition Time vs. Load Capacitance. Typical Maximum-clock Frequency vs. Supply Voltage. Dynamic Power Dissipation vs. Input Clock Frequency. 8/14 HCC/HCF4094B TYPICAL APPLICATION REMOTE CONTROL HOLDING REGISTER TEST CIRCUITS Quiescent Device Current. Noise Immunity. Input Leakage Current. 9/14 HCC/HCF4094B Plastic DIP16 (0.25) MECHANICAL DATA mm DIM. MIN. a1 0.51 B 0.77 TYP. inch MAX. MIN. TYP. MAX. 0.020 1.65 0.030 0.065 b 0.5 0.020 b1 0.25 0.010 D 20 0.787 E 8.5 0.335 e 2.54 0.100 e3 17.78 0.700 F 7.1 0.280 I 5.1 0.201 L Z 3.3 0.130 1.27 0.050 P001C 10/14 HCC/HCF4094B Ceramic DIP16/1 MECHANICAL DATA mm DIM. MIN. TYP. inch MAX. MIN. TYP. MAX. A 20 0.787 B 7 0.276 D E 3.3 0.130 0.38 e3 0.015 17.78 0.700 F 2.29 2.79 0.090 0.110 G 0.4 0.55 0.016 0.022 H 1.17 1.52 0.046 0.060 L 0.22 0.31 0.009 0.012 M 0.51 1.27 0.020 0.050 N P Q 10.3 7.8 8.05 5.08 0.406 0.307 0.317 0.200 P053D 11/14 HCC/HCF4094B SO16 (Narrow) MECHANICAL DATA mm DIM. MIN. TYP. A a1 inch MAX. MIN. TYP. 1.75 0.1 0.068 0.2 a2 MAX. 0.004 0.007 1.65 0.064 b 0.35 0.46 0.013 0.018 b1 0.19 0.25 0.007 0.010 C 0.5 0.019 c1 45° (typ.) D 9.8 E 5.8 10 0.385 6.2 0.228 0.393 0.244 e 1.27 0.050 e3 8.89 0.350 F 3.8 4.0 0.149 0.157 G 4.6 5.3 0.181 0.208 L 0.5 1.27 0.019 0.050 M S 0.62 0.024 8° (max.) P013H 12/14 HCC/HCF4094B PLCC20 MECHANICAL DATA mm DIM. MIN. TYP. inch MAX. MIN. TYP. MAX. A 9.78 10.03 0.385 0.395 B 8.89 9.04 0.350 0.356 D 4.2 4.57 0.165 0.180 d1 2.54 0.100 d2 0.56 0.022 E 7.37 8.38 0.290 0.330 e 1.27 0.050 e3 5.08 0.200 F 0.38 0.015 G 0.101 0.004 M 1.27 0.050 M1 1.14 0.045 P027A 13/14 HCC/HCF4094B Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsability for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may results from its use. No license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. SGS-THOMSON Microelectronics products are not authorized for use ascritical components in life support devices or systems without express written approval of SGS-THOMSON Microelectonics. 1994 SGS-THOMSON Microelectronics - All Rights Reserved SGS-THOMSON Microelectronics GROUP OF COMPANIES Australia - Brazil - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A 14/14