Product Bulletin HDC135 September 1996 High Speed Optocouplers Types HDC135, HDC136, HDC135B, HDC136B Features Absolute Maximum Ratings (No derating required up to 70o C) • High speed • TTL compatible • High common mode transient Storage Temperature Range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55o C to +150o C Operating Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55o C to +125o C Lead Soldering Temperature [1/16 inch (1.6 mm) from case for 10 seconds) . 260o C Average Input Current - IF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 mA(1) Peak Output Current - IF (50% duty cycle, 1 ms pulse width) . . . . . . . . . . . . 50 mA(2) Peak Transient Input Current - IF (≤ 1 µs pulse width, 300 pps) . . . . . . . . . . . . . 1.0 A Reverse Input Voltage - VR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.0 V Input Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 mW(3) Average Output Current - IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.0 mA Peak Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.0 mA Emitter-Base Reverse Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.0 V Supply and Output Voltage - VCC, VO . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 V to 15 V Base Current - IB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.0 mA Output Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 mW(4) immunity • Wide bandwidth • Open collector output Description Optek’s HDC135 and HDC136 are high speed optocouplers, consisting of IR emitters and integrated photodetectors in hermetic side brazed dual-in-line 8 pin packages. Electrical characteristics are similar to the 6N135 and 6N136 optocouplers but with full military temperature range operation. The HDC135B and HDC136B are high reliability optocouplers with 100% processing and Group Testing patterned after MIL-STD-883 Method 5004 and 5005 for class B. Typical screening and lot acceptance tests are provided on page 13-4. Caution: This component is susceptible to damage from electrostatic discharge. Normal static prevention procedures should be used in handling. Notes: (1) Derate linearly above 70o C free-air temperature at a rate of 0.45 mA/o C. (2) Derate linearly above 70o C free-air temperature at a rate of 0.9 mA/o C. (3) Derate linearly above 70o C free-air temperature at a rate of 0.8 mW/o C. (4) Derate linearly above 70o C free-air temperature at a rate of 1.8 mW/o C. (5) CMH is the maximum allowable dV/dt on the leading edge of a common mode pulse to assure that the output will not switch from high to low. (6) CML is the maximum negative dV/dt allowable on the trailing edge of a common mode pulse to assure that the output will not switch from low to high. (7) Test conditions represents 1 TTL unit load with 5.6 kΩ pull-up resistor. (8) Test conditions represents 1 LSTTL unit load with a 6.1 kΩ pull-up resistor. (9) Device considered a two-terminal device: pins 2 and 3 shorted together and pins 5, 6, 7 and 8 shorted together. Minimum orders will apply to processed devices. Optek Technology, Inc. 1215 W. Crosby Road Carrollton, Texas 75006 13-22 (214) 323-2200 Fax (214) 323-2396 Types HDC135, HDC136, HDC135B, HDC136B Electrical Characteristics (Over recommended temperature TA = -55o C to +125o C, unless otherwise noted) SYMBOL PARAMETER Current Transfer Ratio CTR Logic Low Output Voltage MIN TYP* MAX UNITS HDC135 7.0 HDC136 19.0 19.0 25.0 % % IF = 16 mA, VO = 0.40 V, VCC = 4.5 V, TA = 25o C HDC135 5.0 HDC136 15.0 15.0 23.0 % % IF = 16 mA, VO = 0.50 V, VCC = 4.5 V HDC135 0.100 0.40 V IF = 16 mA, IO = 1.10 mA, VCC = 4.5 V HDC136 0.100 0.40 V IF = 16 mA, IO = 2.4 mA, VCC = 4.5 V 500 nA IF = 0 mA, VO = VCC = 5.5 V, TA = 25o C 0.010 1.00 µA IF = 0 mA, VO = VCC = 15 V, TA = 25o C µA IF = 0 mA, VO = VCC = 15 V µA IF = 16 mA, VO = open, VCC = 15 V 0.020 1.00 µA IF = 0 mA, VO = open, VCC = 15 V, TA = 25o C 2.0 µA IF = 0 mA, VO = open, VCC = 15 V 1.70 V IF = 16 mA, TA = 25o C VOL Logic High Output Current 3.0 IOH 50 ICCL Logic Low Supply Current 40 Logic High Supply Current ICCH VF Input Forward Voltage 1.50 ∆VF ∆TA Temperature Coefficient of Forward Voltage -1.80 BVR Input Reverse Breakdown Voltage CIN TEST CONDITIONS mV/o C 5.0 Input Capacitance 42 V IR = 10 µA, TA = 25o C pF f = 1 MHz, VF = 0 µA 45% Relative Humidity, t = 5 sec, VIO = 1000 Vdc, TA = 25o C (Note 9) Input-Output Insulation Leakage Current IIO 1.00 IF = 16 mA RIO Input-Output Resistance 1012 Ω VIO = 500 Vdc (Note 9) CIO Input-Output Capacitance 0.50 pF f = 1 MHz (Note 9) hFE Transistor DC Current Gain 150 — VO = 5 V, IO = 3 mA o Switching Specification (TA = 25 C) VCC = 5.0 V, IF = 16.0 mA unless otherwise noted tPHL Propagation Delay Time to Logic Low at Output HDC135 HDC136 0.50 0.60 1.50 1.00 µs µs RL = 4.1 kΩ (Note 8) RL = 1.90 kΩ (Note 7) tPLH Propagation Delay Time to Logic High at Output HDC135 HDC136 0.40 0.80 1.50 1.00 µs µs RL = 4.1 kΩ (Note 8) RL = 1.90 kΩ (Note 7) HDC135 1000 V/µs CMH Common Mode Transient Immunity at Logic High Level Output HDC136 1000 V/µs HDC135 -1000 V/µs HDC136 -1000 V/µs CML Common Mode Transient Immunity at Logic Low Level Output IF = 0 mA, VCM = 10 Vp-p, RL = 4.1 kΩ (Notes 6,8) IF = 0 mA, VCM = 10 Vp-p, RL = 1.90 kΩ (Notes 6,7) VCM = 10 Vp-p, RL = 4.1 kΩ, (Notes 5,8) VCM = 10 Vp-p, RL = 1.90 kΩ (Notes 5,7) * All typicals at TA = 25o C and VCC = 5 V, unless otherwise noted Optek reserves the right to make changes at any time in order to improve design and to supply the best product possible. Optek Technology, Inc. 1215 W. Crosby Road Carrollton, Texas 75006 (214)323-2200 Fax (214)323-2396 13-23