10 mm and 13 mm Slim Font Seven Segment Displays Technical Data HDSP-315x Series HDSP-316x Series HDSP-515x Series HDSP-516x Series Features Description • Excellent Appearance • Slim Font Design • Mitered Corners, Evenly Illuminated Segments • Gray Face for Optimum On/Off Contrast • Choice of Colors: DH AlGaAs Red, High Efficiency Red (HER), Yellow, and Green • Low Current Available, AlGaAs Red and HER Choice of Character Size: 10 mm and 13 mm • ± 50° Viewing Angle • Characterized for Luminous Intensity The HDSP-31xx-51xx Series of displays incorporates a new slim font character design. This slim font features narrow width, specially mitered segments to give a fuller appearance to the illuminated character. Faces of these displays are painted a neutral gray for enhanced on/off contrast. All devices are available in either common anode or common cathode configuration with right hand decimal point. Low current versions are available in either AlGaAs red or HER. Devices AlGaAs Red Low Current HDSP- HER Std. Current HDSP- HER Low Current HDSP- Yellow Std. Current HDSP- Green Std. Current HDSP- 315H 315E 315L 315Y 315G Common Anode, 10 mm Display A 316H 316E 316L 316Y 316G Common Cathode, 10 mm Display B 515H 515E 515L 515Y 515G Common Anode, 13 mm Display A 516H 516E 516L 516Y 516G Common Cathode, 13 mm Display B Description Package Drawing 2 Part Numbering System 5082 -X X X X-X X X X X HDSP-X X X X-X X X X X Mechanical Options[1] 00: No Mechanical Option Color Bin Options[1,2] 0: No Color Bin Limitation Maximum Intensity Bin[1,2] 0: No Maximum Intensity Bin Limitation Minimum Intensity Bin[1,2] 0: No Minimum Intensity Bin Limitation Device Configuration/Color [1] H: AlGaAs Red E: High Efficiency Red G: Green Y: Yellow Device Specific Configuration[1] Refer to Respective Datasheet Package[1] Refer to Respective Datasheet Notes: 1. For codes not listed in the figure above, please refer to the respective datasheet or contact your nearest Agilent representative for details. 2. Bin options refer to shippable bins for a part number. Color and Intensity Bins are typically restricted to 1 bin per tube (exceptions may apply). Please refer to respective datasheet for specific bin limit information. 3 HDSP-315x/316x Series LUMINOUS INTENSITY CATEGORY 6 COLOR BIN (NOTE 3) 10° 0.9 2.54 ± 0.38 HDSP-XXXX XYY ZW 12.8 ± 0.2 10 a 1 f 2 b g 4 x 2.54 3 4 0.53 ± 0.05 DIA. 1.2 6.4 ± 0.1 c 7 DP 6 d PIN 1 2 3 4 5 6 7 8 9 10 DATE CODE 7 ± 0.1 10.4 MIN. 9 8 e 5 9.7 ± 0.1 10 FUNCTION g f Common A/C e d DP c Common A/C b a 0.3 ± 0.05 7.62 ± 0.38 HDSP-515x/516x Series LUMINOUS INTENSITY CATEGORY 7.40 10° COLOR BIN (NOTE 3) 10 9 8 7 6 1.25 5.08 + 0.3 17.50 – 0.1 HDSP-XXXX XYY ZW 13.0 a f DATE CODE e d 0.29 ± 0.08 TYP. DIA. 1.25 12.25 ± 0.15 7.00 ± 0.1 3.60 ± 0.3 c DP 1 2 3 4 5 PIN 6.40 ± 0.1 b g 15.24 ± 0.3 1 2 3 4 5 6 7 8 9 10 1.04 ± 0.3 TYP. 0.58 ± 0.08 2.54 ± 0.3 TYP. NOTES: 1. PACKAGE DIMENSIONS IN MILLIMETERS. 2. UNTOLERANCED DIMENSIONS ARE FOR REFERENCE ONLY. 3. FOR YELLOW AND GREEN DEVICES ONLY. FUNCTION e d Common A/C c DP b a Common A/C f g 4 Absolute Maximum Ratings AlGaAs Red Low Current HER HER Low Current Yellow Green Units Average Power per Segment or DP 37 105 52 80 105 mW Peak Forward Current per Segment or DP 45 90[2] 45 60[5] 90[7] mA DC Forward Current per Segment or DP 15[1] 30[3] 15[4] 20[6] 30[8] mA Operating Temperature Range -20 to 100 Description -40 to +100 °C Storage Temperature Range -40 to +100 °C Reverse Voltage per Segment or DP 3.0 V Wavesoldering Temperature for 3 seconds 1.59 mm. below body 250 °C Notes: 1. Derate above 91°C at 0.53 mA/°C. 2. See Figure 4 to establish pulsed conditions. 3. Derate above 53°C at 0.45 mA/°C. 4. Derate above 80°C at 0.38 mA/°C. 5. See Figure 5 to establish pulsed conditions. 6. Derate above 81°C at 0.52 mA/°C. 7. See Figure 6 to establish pulsed ocnditions. 8. Derate above 39°C at 0.37 mA/°C. 5 Electrical/Optical Characteristics at TA = 25°C AlGaAs Red Low Current Device Series HDSP315/316H 515/516H Parameter Luminous Intensity/Segment[1,2] (Digit Average) Symbol IV Forward Voltage/Segment or DP Peak Wavelength Dominant Wavelength[3] Reverse Voltage/Segment or DP[4] Thermal Resistance LED Junction-to-Pin Typ. 650 Max. Units µcd VF 1.8 2.2 V λPEAK 645 nm λd 637 nm 15 V 255 °C/W/Seg VR Min. 180 3 RθJ-PIN Test Conditions IF = 1 mA IF = 1 mA IR = 100 µA HER Device Series HDSP315/316E 515/516E V IF = 10 mA Forward Voltage/Segment or DP VF 1.9 λPEAK 635 nm Dominant Wavelength[3] λd 626 nm Reverse Voltage/Segment or DP[4] VR 30 V 200 °C/W/Seg Thermal Resistance LED Junction-to-Pin 3 RθJ-PIN Typ. Max. 2600 Test Conditions IF = 10 mA Symbol IV Peak Wavelength Min. 450 Units µcd Parameter Luminous Intensity/Segment[1,2] (Digit Average) 2.5 IR = 100 µA HER Low Current Device Series HDSP315/316L 515/516L Parameter Luminous Intensity/Segment[1,2] (Digit Average) Symbol IV Forward Voltage/Segment or DP Peak Wavelength Dominant Wavelength[3] Reverse Voltage/Segment or Thermal Resistance LED Junction-to-Pin DP[4] Typ. 370 Max. Units µcd VF 2.1 2.5 V λPEAK 635 nm λd 626 nm 30 V 200 °C/W/Seg VR RθJ-PIN Min. 180 3 Test Conditions IF = 2 mA IF = 2 mA IR = 100 µA 6 Yellow Device Series HDSP315/316Y 515/516Y V IF = 10 mA Forward Voltage/Segment or DP VF 2.0 λPEAK 583 nm λd 586 nm 50 V 200 °C/W/Seg Dominant Wavelength [3] Reverse Voltage/Segment or DP[4] VR Thermal Resistance LED Junction-to-Pin 3 RθJ-PIN Typ. Max. 1800 Test Conditions IF = 10 mA Symbol IV Peak Wavelength Min. 450 Units µcd Parameter Luminous Intensity/Segment[1,2] (Digit Average) 2.5 IR = 100 µA Green Device Series HDSP315/316E 515/516E V IF = 10 mA Forward Voltage/Segment or DP VF 2.1 λPEAK 566 nm λd 571 nm 50 V 200 °C/W/Seg Dominant Wavelength [3] Reverse Voltage/Segment or DP[4] VR Thermal Resistance LED Junction-to-Pin 3 RθJ-PIN Typ. Max. 5000 Test Conditions IF = 10 mA Symbol IV Peak Wavelength Min. 450 Units µcd Parameter Luminous Intensity/Segment[1,2] (Digit Average) 2.5 IR = 100 µA Notes: 1. Case temperature of device immediately prior to the intensity measurement is 25°C. 2. The digits are categorized for luminous intensity. The intensity category is designated by a letter on the side of the package. 3. The dominant wavelength, λ is derived from the CIE chromaticity diagram and is that single wavelength which defines the color of the device. 4. Typical specification for reference only. Do not exceed absolute maximum ratings. 50.0 18 16 Rθ J-A = 770°C/W 14 12 10 8 6 4 2 20 RELATIVE LUMINOUS INTENSITY (NORMALIZED TO 1 AT 1mA) 20 20.0 IF – FORWARD CURRENT PER SEGMENT – mA IF AVE. MAX – MAXIMUM AVERAGE FORWARD CURRENT PER SEGMENT – mA AlGaAs Low Current 10.0 5.0 2.0 1.0 0.5 0.1 0 20 30 40 50 60 70 80 90 100 110 120 TA – AMBIENT TEMPERATURE – °C Figure 1. Maximum Allowable Average or DC Current vs. Ambient Temperature. 0 0.5 1.0 1.5 2.0 VF – FORWARD VOLTAGE – V Figure 2. Forward Current vs. Forward Voltage. 2.5 10 5 2 1 0.5 0.2 0.1 0.1 0.2 0.5 1 2 5 10 IF – FORWARD CURRENT PER SEGMENT – mA Figure 3. Relative Luminous Intensity vs DC Forward Current. 20 7 OPERATION IN THIS REGION REQUIRES TEMPERATURE DERATING OF IDC MAXIMUM 10 1000 10000 1 1 10 IF PEAK RATIO OF MAXIMUM OPERATING PEAK CURRENT TO TEMPERATURE IDC MAX DERATED DC CURRENT 50 OPERATION IN THIS REGION REQUIRES TEMPERATURE DERATING OF IDC MAXIMUM 10 KH Z KH Hz 0 10 Hz 0 30 z KH z 1 3 10 10 100 1000 10000 IDC MAX – MAXIMUM DC CURRENT PER SEGMENT – mA 100 1 Rθ 45 80 60 YELLOW 40 HER 20 GREEN 3.0 4.0 VF – FORWARD VOLTAGE – V Figure 8. Forward Current vs. Forward Voltage Characteristics. J-A = 770°C/W 35 30 25 HER GREEN 20 YELLOW 15 10 5 0 20 30 40 50 60 70 80 90 100 110 120 DC OPERATION 5.0 Figure 7. Maximum Allowable DC Current per Segment as a Function of Ambient Temperature. RELATIVE LUMINOUS INTENSITY (NORMALIZED TO 1 AT 5 mA FOR HER AND YELLOW AND TO 1 AT 10 mA FOR GREEN) IF – FORWARD CURRENT PER SEGMENT – mA 100 2.0 10000 TA – AMBIENT TEMPERATURE – °C Figure 6. Allowable Peak Current vs. Pulse Duration – Green. 1.0 1000 40 tp – PULSE DURATION – µs 0 Hz Figure 5. Maximum Tolerable Peak Current vs. Pulse Duration – Yellow. Figure 4. Maximum Tolerable Peak Current vs. Pulse Duration – HER. 0 100 0 tp – PULSE DURATION – µs tp – PULSE DURATION – µs 1 10 z 0H 30 Hz 1K Hz 100 DC OPERATION Z 10 z 10 3K 1 H OPERATION IN THIS REGION REQUIRES TEMPERATURE DERATING OF IDC MAXIMUM KH 1 0 100 100 10 IF PEAK RATIO OF MAXIMUM OPERATING PEAK CURRENT TO TEMPERATURE IDC MAX DERATED DC CURRENT 100 Hz 0 30 Hz 1K Hz 3K Z KH 10 IF PEAK RATIO OF MAXIMUM OPERATING PEAK CURRENT TO TEMPERATURE IDC MAX DERATED DC CURRENT HER, Yellow, and Green 12 10 HER 8 YELLOW 6 4 GREEN 2 0 0 5 10 15 20 25 30 IF – FORWARD CURRENT PER SEGMENT – mA Figure 9. Relative Luminous Intensity vs. DC Forward Current. DC OPERATION 8 18 Rθ J-A = 770°C/W 16 14 HER 12 10 8 6 4 2 0 20 30 40 50 60 70 80 90 100 110 120 TA – AMBIENT TEMPERATURE – °C Figure 10. Maximum Allowable Average or DC Current vs. Ambient Temperature. 50 40 30 20 HER 10 0 0 0.5 1.0 1.5 2.0 2.5 VF – FORWARD VOLTAGE – V Figure 11. Forward Current vs. Forward Voltage. Intensity Bin Limits (mcd) HER Low Current, AlGaAs Red Low Current HDSP-31xL/H, HDSP-51xL/H IV Bin Category Min. Max. E 0.180 0.360 F 0.280 0.560 G 0.450 0.900 H 0.700 1.400 I 1.100 2.200 K 1.800 3.600 L 2.800 5.600 M 4.500 9.000 N 7.000 15.000 HER Std. Current, Green Std. Current, Yellow Std. Current HDSP-31xE/G/Y, HDSP-51xE/G/Y IV Bin Category Min. Max. G 0.450 0.900 H 0.700 1.400 I 1.100 2.200 K 1.800 3.600 L 2.800 5.600 M 4.500 9.000 N 7.000 15.000 3.0 RELATIVE LUMINOUS INTENSITY (NORMALIZED TO 1 AT 2 mA FOR HER AND TO 1 AT 4 mA FOR YELLOW AND GREEN 20 IF – FORWARD CURRENT PER SEGMENT – mA IF AVE. MAX – MAXIMUM AVERAGE FORWARD CURRENT PER SEGMENT – mA HER Low Current 16 14 12 10 HER 8 6 4 2 0 0 2 4 6 8 10 12 14 16 VF – FORWARD CURRENT PER SEGMENT – mA Figure 12. Relative Luminous Intensity vs. DC Forward Current. 9 Color Categories Color Yellow Green Bin 1 3 2 4 2 3 4 5 Dominant Wavelength (nm) Min. Max. 581.50 585.00 584.00 587.50 586.50 590.00 589.00 592.50 573.00 577.00 570.00 574.00 567.00 571.00 564.00 568.00 Note: All categories are established for classification of products. Products may not be available in all categories. Please contact your local Agilent representatives for further clarification/information. Electrical/Optical Soldering/Cleaning For more information on electrical/optical characteristics, please see Application Note 1005. Cleaning agents from the ketone family (acetone, methyl ethyl ketone, etc.) and from the chlorinated hydrocarbon family (methylene chloride, trichloroethylene, carbon tetrachloride, etc.) are not recommended for cleaning LED parts. All of these Contrast Enhancement For information on contrast enhancement, please see Application Note 1015. various solvents attack or dissolve the encapsulating epoxies used to form the package of plastic LED parts. For further information on soldering LEDs, please refer to Application Note 1027. www.agilent.com/semiconductors For product information and a complete list of distributors, please go to our web site. For technical assistance call: Americas/Canada: +1 (800) 235-0312 or (916) 788-6763 Europe: +49 (0) 6441 92460 China: 10800 650 0017 Hong Kong: (+65) 6756 2394 India, Australia, New Zealand: (+65) 6755 1939 Japan: (+81 3) 3335-8152(Domestic/International), or 0120-61-1280(Domestic Only) Korea: (+65) 6755 1989 Singapore, Malaysia, Vietnam, Thailand, Philippines, Indonesia: (+65) 6755 2044 Taiwan: (+65) 6755 1843 Data subject to change. Copyright © 2005 Agilent Technologies, Inc. Obsoletes 5988-3204EN March 9, 2005 5989-2640EN