CURRENT 16.0 Amperes VOLTAGE 50 to 600 Volts HEP1601 THRU HEP1606 Features · Plastic package has Underwriters Laboratory Flammability Classification 94V-0 · Low forward voltage drop · High current capability · High reliability · Low power loss, high effciency · High surge current capability · High speed switching · Low leakage ITO-220A 10 0.5 6.4 0.1 13Min 0.7 0.2 5.08 · Case : JEDEC ITO-220A molded plastic body · Terminals : Lead solderable per MIL-STD-750, method 2026 · Polarity : As marked · Mounting Position : Any · Weight : 0.08 ounce, 2.24 gram 15 0.3 2.7 0.2 1.3 0.2 3.7 0.2 Mechanical Data 4.5 0.2 2.7 3.2 PIN 1 + 0.5 2.4 PIN 1 CASE PIN 2 + Case Negative Suffix"R" + CASE PIN 2 CasePositive Dimensions in inches and (millimeters) Maximum Ratings And Electrical Characteristics (Ratings at 25℃ ambient temperature unless otherwise specified, Single phase, half wave 60Hz, resistive or inductive load. For capacitive load, derate by 20%) Symbols HEP 1601 HEP 1602 HEP 1603 HEP 1604 HEP 1605 HEP 1606 Units Maximum recurrent peak reverse voltage VRRM 50 100 200 300 400 600 Volts Maximum RMS voltage VRMS 35 70 140 210 280 420 Volts Maximum DC blocking voltage VDC 50 100 200 300 400 600 Volts Maximum average forward rectified current 0.375"(9.5mm) lead length @ at TA=100℃ I(AV) 8.0 Amps Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC method) IFSM 125 Amps Maximum instantaneous forward voltage at 8.0A VF 1.0 1.3 Maximum DC reverse current at rated DC blocking voltage TA=25℃ Maximum DC reverse current at rated DC blocking voltage TA=125℃ 1.7 Volts 10.0 μA IR 100 Maximum reverse recovery time (Note 1) Trr 50 80 ns Typical junction capacitance (Note 2) CJ 80 50 pF Typical thermal resistance (Note 3) RθJC Operating junction and storage temperature range TJ TSTG Notes: (1) Test conditions: IF=0.5A, IR=1.0A, Irr=0.25A. (2) Measured at 1MHz and applied reverse voltage of 4.0 Volts. (3) Thermal resistance from junction to case mounting on heatsink. 2.2 -55 to +150 -55 to +150 ℃/W ℃ RATINGS AND CHARACTERISTIC CURVES HEP1601 THRU HEP1606 FIG . 1 -REVERSE RECOVERY TIME CHARACTERISTIC 50 NONINDUCTIVE AND TEST CIRCUIT DIAGRAM 10 trr NONINDUCTIVE DUT (+ ) 50Vdc (approx) (-) +0.5A PULSE GENERATOR ( NOTE 2 ) NONINDUCTIVE OSCILLOSCOPE (NOTE 2 ) -1.0A 1cm FIG . 2 -MAXIMUM AVERAGE FORWARD CURRENT DERATING CURVE 20 12 8 4 0 0 150 100 50 CASE TEMPERATURE ( % ) . FIG . 4 -MAXIMUM NON - REPETITIVE FORWARD SURGE CURRENT 8.3ms Single Half Sine Tj=25oC Wave JEDEC Method 120 INSTANTAN EOUS REVERSE CURRET . ( 16 FIG . 3 -TYPICAL REVERSE CHARACTERISTICS Tj=125 C O 100 10 Tj=25 C O 1 0.1 90 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE . (%) Tj=25oC 200 160 HE 120 80 H E P 1 40 1 2 60 6-1 P1 60 60 1-1 60 5 8 5 10 20 50 100 REVERSE VOLTAGE . ( V) 200 500 1000 5 60 P1 08 16 240 3.0 6- FIG . 5 -TYPICAL JUNCTIOON CAPACITANCE PER LEG 10 1.0 60 NMBER OF CYCLES AT 60Hz 30 P1 100 HE 50 4 20 60 10 1-1 5 60 2 P1 1 FIG . 6 -TYPICAL FRWARD CHARACTERISTICS HE 30 100 HE 60 0 SET TIME BASE FOR 5/ 10ns / cm A) 1000 INSTANTANEOUS FORWARD CURRENT . ( A) CAPACITANCE ( pF) AVERAGE FORWARD CURRENT . ( A ) NOTES: 1 . RISE TIME = 7nsmax. INPUT IMPEDANCE= 1 MEGOHM 22pf 2 . RISETIME = 10ns max. SOURSE IMPEDANCE = 50ohmsf PE A K F O R W A R D S U R G E C U R R E N T . ( A ) 0 -0.25A 0.3 0.1 0.03 .01 0.4 0.6 0.8 1.0 Tj=25oC Pulse Width=300 1% Duty Cycle s 1.2 1.8 1.4 1.6 FORWARD VOLTAGE . ( V )