AVAGO HFBR

HFBR-0507Z Series
HFBR-15X7Z Transmitters
HFBR-25X6Z Receivers
125 Megabaud Versatile Link
The Versatile Fiber Optic Connection
Data Sheet
Description
Features
The 125 MBd Versatile Link (HFBR-0507Z Series) is the
most cost-effective fiber-optic solution for transmission
of 125 MBd data over 100 meters. The data link consists
of a 650 nm LED transmitter, HFBR-15X7Z, and a PIN/preamp receiver, HFBR-25X6Z. These can be used with lowcost plastic or silica fiber. One mm diameter plastic fiber
provides the lowest cost solution for distances under 25
meters. The lower attenuation of silica fiber allows data
transmission over longer distance, for a small difference
in cost. These components can be used for high speed
data links without the problems common with copper
wire solutions, at a competitive cost.
 RoHS-compliant
 Data transmission at signal rates of 1 to 125 MBd over
distances of 100 meters
 Compatible with inexpensive, easily terminated plastic optical fiber, and with large core silica fiber
 High voltage isolation
 Transmitter and receiver application circuit
schematics and recommended board layouts available
 Interlocking feature for single channel or duplex links,
in a vertical or horizontal mount configuration
The HFBR-15X7Z transmitter is a high power 650 nm
LED in a low cost plastic housing designed to efficiently
couple power into 1 mm diameter plastic optical fiber
and 200 μm Hard Clad Silica (HCS®) fiber. With the recommended drive circuit, the LED operates at speeds from
1-125 MBd. The HFBR-25X6Z is a high bandwidth analog
receiver containing a PIN photodiode and internal transimpedance amplifier. With the recommended application circuit for 125 MBd operation, the performance of
the complete data link is specified for of 0-25 meters with
plastic fiber and 0-100 meters with 200 μm HCS® fiber. A
wide variety of other digitizing circuits can be combined
with the HFBR-0507Z Series to optimize perfor-mance
and cost at higher and lower data rates.
HCS® is a registered trademark of Spectran Corporation.
Applications








Intra-system links: board-to-board, rack-to-rack
Telecommunications switching systems
Computer-to-peripheral data links, PC bus extension
Industrial control
Proprietary LANs
Digitized video
Medical instruments
Reduction of lightning and voltage transient susceptibility
HFBR-0507Z Series
125 MBd Data Link
Data link operating conditions and performance are
specified for the HFBR-15X7Z transmitter and HFBR-25X6Z
receiver in the recommended applications circuits shown
in Figure 1. This circuit has been optimized for 125 MBd
operation. The Applications Engineering Department in
the Avago Optical Communication Division is available to
assist in optimizing link performance for higher or lower
speed operation.
Recommended Operating Conditions for the Circuits in Figures 1 and 2.
Parameter
Symbol
Min.
Unit
70
°C
TA
Supply Voltage
VCC
+4.75
+5.25
V
Data Input Voltage – Low
VIL
VCC -1.89
VCC -1.62
V
Data Input Voltage – High
VIH
VCC -1.06
VCC -0.70
V
Data Output Load
RL
45
55
Ω
fS
1
125
MBd
D.C.
40
60
%
Signaling Rate
Duty Cycle
0
Max.
Ambient Temperature
Reference
Note 1
Note 2
Link Performance: 1-125 MBd, BER ≤ 10-9, under recommended operating conditions with recommended transmit
and receive application circuits.
Parameter
Symbol
Min.[3]
Typ.[4]
Optical Power Budget, 1 m POF
OPBPOF
11
16
dB
Note 5,6,7
Optical Power Margin,
20 m Standard POF
OPMPOF,20
3
6
dB
Note 5,6,7
Link Distance with
Standard 1 mm POF
l
20
27
m
Optical Power Margin,
25 m Low Loss POF
OPMPOF,25
3
6
dB
l
25
32
m
OPBHCS
7
12
dB
Note 5,6,7
OPMHCS,100
3
6
dB
Note 5,6,7
l
100
125
m
Link Distance with Extra
Low Loss 1 mm POF
Optical Power Budget, 1 m HCS
Optical Power Margin,
100 m HCS
Link Distance with HCS Cable
Max.
Unit
Condition
Reference
Note 5,6,7
Notes:
1. If the output of U4C in Figure 1, page 4 is transmitted via coaxial cable, terminate with a 50 Ω resistor to VCC - 2 V.
2. Run length limited code with maximum run length of 10 μs.
3. Minimum link performance is projected based on the worst case specifications of the HFBR-15X7Z transmitter, HFBR-25X6Z receiver,
and POF cable, and the typical performance of other components (e.g. logic gates, transistors, resistors, capacitors, quantizer, HCS cable).
4. Typical performance is at 25°C, 125 MBd, and is measured with typical values of all circuit components.
5. Standard cable is HFBR-RXXYYYZ plastic optical fiber , with a maximum attenuation of 0.24 dB/m at 650 nm and NA = 0.5.
Extra low loss cable is HFBR-EXXYYYZ plastic optical fiber, with a maximum attenuation of 0.19 dB/m at 650 nm and NA = 0.5.
HCS cable is HFBR-H/VXXYYY glass optical fiber, with a maximum attenuation of 10 dB/km at 650 nm and NA = 0.37.
6. Optical Power Budget is the difference between the transmitter output power and the receiver sensitivity, measured after 1 meter of fiber.
The minimum OPB is based on the limits of optical component performance over temperature, process, and recommended power supply
variation.
7. The Optical Power Margin is the available OPB after including the effects of attenuation and modal dispersion for the minimum link distance:
OPM = OPB - (attenuation power loss + modal dispersion power penalty). The minimum OPM is the margin available for longterm LED LOP
degradation and additional fixed passive losses (such as in-line connectors) in addition to the minimum specified distance.
2
Plastic Optical Fiber (1 mm POF) Transmitter Application Circuit: Performance of the HFBR-15X7Z transmitter in the recommended application circuit (Figure 1) for POF; 1-125 MBd, 25°C.
Parameter
Symbol
Typical
Unit
Condition
Note
Average Optical Power 1 mm POF
Pavg
-9.7
dBm
Average Modulated Power 1 mm POF
Pmod
-11.3
dBm
tr
2.1
ns
5 MHz
5 MHz
Optical Rise Time (10% to 90%)
50% Duty
Cycle
Note 1, Fig 3
Note 2, Fig 3
Optical Fall Time (90% to 10%)
tf
2.8
ns
High Level LED Current (On)
IF,H
19
mA
Note 3
Low Level LED Current (Off )
IF,L
Note 3
Optical Overshoot - 1 mm POF
Transmitter Application Circuit
Current Consumption - 1 mm POF
ICC
3
mA
45
%
110
mA
Figure 1
Hard Clad Silica Fiber (200 μm HCS) Transmitter Application Circuit: Performance of the HFBR-15X7Z transmitter in the recommended application circuit (Figure 1) for HCS; 1-125 MBd, 25°C.
Parameter
Symbol
Typical
Unit
Condition
Note
Average Optical Power 200 μm HCS
Pavg
-14.6
dBm
Average Modulated Power 200 μm HCS
Pmod
-16.2
dBm
Optical Rise Time (10% to 90%)
tr
3.1
ns
5 MHz
Optical Fall Time (90% to 10%)
tf
3.4
ns
5 MHz
High Level LED Current (On)
IF,H
60
mA
Note 3
Low Level LED Current (Off)
IF,L
6
mA
Note 3
30
%
ICC
130
mA
Optical Overshoot - 200 μm HCS
Transmitter Application Circuit
Current Consumption - 200 μm HCS
50% Duty
Cycle
Note 1, Fig 3
Note 2, Fig 3
Figure 1
Notes:
1. Average optical power is measured with an average power meter at 50% duty cycle, after 1 meter of fiber.
2. To allow the LED to switch at high speeds, the recommended drive circuit modulates LED light output between two non-zero power levels.
The modulated (useful) power is the difference between the high and low level of light output power (transmitted) or input power (received),
which can be measured with an average power meter as a function of duty cycle (see Figure 3). Average Modulated Power is defined as one
half the slope of the average power versus duty cycle:
Average Modulated Power =
[Pavg @ 80% duty cycle - Pavg @ 20% duty cycle]
(2) [0.80 - 0.20]
3. High and low level LED currents refer to the current through the HFBR-15X7Z LED. The low level LED “off” current, sometimes referred to as
“hold-on” current, is prebias supplied to the LED during the off state to facilitate fast switching speeds.
3
Plastic and Hard Clad Silica Optical Fiber Receiver Application Circuit: Performance[4] of the HFBR-25X6Z receiver in the recommended application circuit (Figure 1); 1-125 MBd, 25°C unless otherwise stated.
Parameter
Symbol
Typical
Unit
Condition
Note
Data Output Voltage - Low
VOL
VCC -1.7
V
RL = 50 Ω
Note 5
Data Output Voltage - High
VOH
VCC -0.9
V
RL = 50 Ω
Note 5
Receiver Sensitivity to Average
Modulated Optical Power 1 mm POF
Pmin
-27.5
dBm
50% eye opening
Note 2
Receiver Sensitivity to Average
Modulated Optical Power 200 μm HCS
Pmin
-28.5
dBm
50% eye opening
Note 2
Receiver Overdrive Level of Average
Modulated Optical Power 1 mm POF
Pmax
-7.5
dBm
50% eye opening
Note 2
Receiver Overdrive Level of Average
Modulated Optical Power 200 μm HCS
Pmax
-10.5
dBm
50% eye opening
Note 2
ICC
85
mA
RL = ∞
Figure 1
Receiver Application Circuit Current
Consumption
Notes:
4. Performance in response to a signal from the HFBR-15X7Z transmitter driven with the recommended circuit at 1-125 MBd over 1 meter of
HFBR-RZ/EXXYYYZ plastic optical fiber or 1 meter of HFBR-H/VXXYYY hard clad silica optical fiber.
5. Terminated through a 50 Ω resistor to VCC - 2 V.
6. If there is no input optical power to the receiver, electrical noise can result in false triggering of the receiver. In typical applications, data encoding and error detection prevent random triggering from being interpreted as valid data. Refer to Applications Note 1066 for design guidelines.
L1
CB70-1812
C1
0.001
VCC
C2
0.1
R5
22
14
9
10 U1C
C3
0.1
C4
0.001
C5
10
+
7 74ACTQ00
Q1
BFQ52
R6
91
9
8
7
6
5
4
3
2
J1 1
TX VEE
Q2 BASE
Q1 BASE
TX VCC
RX VCC
NC
PIN 19 10H116
PIN 18 10H116
RX VEE
Q2
BFQ52
1
2
12
13 U1D
3
U1A
+
11
1
2
3
4
8
U2
5 HFBR-15X7Z
Q3
2N3904
74ACTQ00
R9*
74ACTQ00
R7
91
4
5 U1B
6
VCC
VBB
R10
15
C8*
C19
0.1
R12
4.7
C10
0.1
R11*
ALL CAPACITOR VALUES
ARE IN MICRO FARADS,
WITH 10% TOLERANCE
(UNLESS OTHERWISE NOTED).
C9
.47
3V
R24
1K
C17
0.1
R22
1K
R18
51
C16
0.1
MC10H116FN
18
19
U4C
15
17
C15
0.1
R25
1K
R23
1K
VBB
C18
0.1
R13
4.7
R16
51
MC10H116FN
4 10
7
3 U4A 5
R19
51
20
MC10H116FN
9 14
13
8 U4B 12
R17
51
2
ALL RESISTANCES ARE IN
OHMS WITH 5% TOLERANCE
(UNLESS OTHERWISE NOTED).
VBB
R14
1K
8
C12
0.1
R15
1K
C11
0.1
1
2
3
4
U3
5 HFBR-25X6Z
3V
VCC
R20
12
R21
62
VBB
+ C14
10
U5
TL431
Figure 1. Transmitter and receiver application circuit with +5 V ECL inputs and outputs.
4
C7
0.001
R8*
74ACTQ00
C20
10
C6
0.1
8
C13
0.1
THE VALUES OF R8, R9, R11, AND
C8 ARE DIFFERENT FOR POF AND
HCS DRIVE CIRCUITS.
R8
R9
R11
C8
HCS TOLERANCE
POF
1%
300
82
1%
82
300
1%
1K
470
1%
43 pF 120 pF
120
120
+5 V ECL
SERIAL DATA
SOURCE
82
0.1 μF
9 T X V EE
82
8 TD
+
5V
7 TD
Ð
4.7 μH
+
10 μF
6 T X V CC
0.1 μF
0.1 μF
5 R X V CC
82
10 μF
82
+
0.1 μF
4
4.7 μH
FIBER-OPTIC
TRANSCEIVER
SHOWN IN
FIGURE 1
3 RD
+5 V ECL
SERIAL DATA
RECEIVER
2 RD
120
120
1 R X V EE
4.7 μH
Figure 2. Recommended power supply filter and +5 V ECL signal terminations for the transmitter and receiver application circuit of Figure 1.
200
21
POF
OPTICAL POWER BUDGET ÐdB
AVERAGE POWER
Ð μW
19
150
100
AVERAGE
MODULATED
POWER
50
AVERAGE POWER,
50% DUTY CYCLE
0
0
20
40
DUTY CYCLE
60
Ð%
Figure 3. Average modulated power.
5
80
100
17
15
HCS
13
11
9
10
30
50
70
90
110
130
150
DATA RATE Ð MBd
Figure 4. Typical optical power budget vs. data rate.
125 Megabaud Versatile Link Transmitter
HFBR-15X7Z Series
Description
GROUND
The HFBR-15X7Z transmitters incorporate a 650 nanometer LED in a horizontal (HFBR-1527Z) or vertical (HFBR-1537Z) gray housing. The HFBR-15X7Z transmitters
are suitable for use with current peaking to decrease
response time and can be used with HFBR-25X6Z receivers in data links operating at signal rates from 1 to 125
megabaud over 1 mm diameter plastic optical fiber or
200 μm diameter hard clad silica glass optical fiber. Refer
to Application Note 1066 for details for recommended
interface circuits.
Absolute Maximum Ratings
Parameter
ANODE
CATHODE
GROUND
GROUND
1
2
3
4
GROUND
SEE NOTE 6
Symbol
Min.
Max.
Unit
Storage Temperature
TS
-40
85
°C
Operating Temperature
TO
-40
70
°C
260
°C
10
s
Lead Soldering Temperature Cycle Time
Transmitter High Level Forward
Input Current
IF,H
120
mA
Transmitter Average Forward Input Current
IF,AV
60
mA
Reverse Input Voltage
VR
3
V
Reference
Note 1, 9
50% Duty Cycle
≥ 1 MHz
CAUTION: The small junction sizes inherent to the design of this component increase the component’s susceptibility to damage from
electrostatic discharge (ESD). It is advised that normal static precautions be taken in handling and assembly of this component to
prevent damage and/or degradation which may be induced by ESD.
WARNING: WHEN VIEWED UNDER SOME CONDITIONS, THE OPTICAL PORT MAY EXPOSE THE EYE BEYOND THE MAXIMUM PERMISSIBLE EXPOSURE RECOMMENDED IN ANSI Z136.2, 1993. UNDER MOST VIEWING CONDITIONS THERE IS NO
EYE HAZARD.
6
Electrical/Optical Characteristics 0 to 70°C, unless otherwise stated.
Parameter
Symbol
Min.
Typ.[2]
Max.
Unit
Condition
Note
Transmitter Output
Optical Power, 1 mm POF
PT
-9.5
-10.4
-7.0
-4.8
-4.3
dBm
IF,dc = 20 mA, 25°C
0-70°C
Note 3
Transmitter Output
Optical Power, 1 mm POF
PT
-6.0
-6.9
-3.0
-0.5
-0.0
dBm
IF,dc = 60 mA, 25°C
0-70°C
Note 3
Transmitter Output
Optical Power,
200 μm HCS®
PT
-14.6
-15.5
-13.0
-10.5
-10.0
dBm
IF,dc = 60 mA, 25°C
0-70°C
Note 3
Output Optical Power
Temperature Coefficient
ΔPT
ΔT
Peak Emission Wavelength
PK
Peak Wavelength
Temperature Coefficient
Δ
ΔT
0.12
nm/°C
FWHM
21
nm
Full Width,
Half Maximum
V
IF = 60 mA
Spectral Width
Forward Voltage
VF
-0.02
640
1.8
650
2.1
dB/°C
660
2.4
nm
Forward Voltage
Temperature Coefficient
ΔVF
ΔT
-1.8
Transmitter Numerical
Aperture
NA
0.5
Thermal Resistance,
Junction to Case
jc
140
°C/W
Reverse Input Breakdown
Voltage
VBR
13
V
IF,dc = -10 μA
Diode Capacitance
CO
60
pF
VF = 0 V,
f = 1 MHz
Unpeaked Optical Rise
Time, 10% - 90%
tr
12
ns
IF = 60 mA
f = 100 kHz
Figure 1
Note 5
Unpeaked Optical Fall
Time, 90% - 10%
tf
9
ns
IF = 60 mA
f = 100 kHz
Figure 1
Note 5
3.0
mV/°C
Note 4
Notes:
1. 1.6 mm below seating plane.
2. Typical data is at 25°C.
3. Optical Power measured at the end of 0.5 meter of 1 mm diameter plastic or 200 μm diameter hard clad silica optical fiber with a large area
detector.
4. Typical value measured from junction to PC board solder joint for horizontal mount package, HFBR-1527Z. jc is approximately
30°C/W higher for vertical mount package, HFBR-1537Z.
5. Optical rise and fall times can be reduced with the appropriate driver circuit; refer to Application Note 1066.
6. Pins 5 and 8 are primarily for mounting and retaining purposes, but are electrically connected; pins 3 and 4 are electrically unconnected. It is
recommended that pins 3, 4, 5, and 8 all be connected to ground to reduce coupling of electrical noise.
7. Refer to the Versatile Link Family Fiber Optic Cable and Connectors Technical Data Sheet for cable connector options for 1 mm plastic optical
fiber and 200 μm HCS fiber.
8. The LED current peaking necessary for high frequency circuit design contributes to electromagnetic interference (EMI). Care must be taken in
circuit board layout to minimize emissions for compliance with governmental EMI emissions regulations. Refer to Application Note 1066 for
design guidelines.
9. Moisture sensitivity level (MSL) is 3
7
HP8082A
PULSE
GENERATOR
BCP MODEL 300
500 MHz
BANDWIDTH
SILICON
AVALANCHE
PHOTODIODE
HP54002A
50 OHM BNC
INPUT POD
50 OHM
LOAD
RESISTOR
HP54100A
OSCILLOSCOPE
NORMALIZED SPECTRAL OUTPUT POWER
1.2
0° C
1.0
25° C
0.8
70° C
0.6
0.4
0.2
0
620
630
640
650
660
670
680
WAVELENGTH (nm)
Figure 1. Test circuit for measuring unpeaked rise and
fall times.
Figure 2. Typical spectra normalized to the 25°C peak.
0
PT - NORMALIZED OUTPUT POWER - dB
VF - FORWARD VOLTAGE - V
2.4
0° C
2.2
25° C
70° C
2.0
1.8
1.6
1
10
100
IF,DC - TRANSMITTER DRIVE CURRENT (mA)
Figure 3. Typical forward voltage vs. drive current.
8
-5
0° C
-10
-15
25° C
70° C
-20
-25
1
10
100
IF,DC - TRANSMITTER DRIVE CURRENT (mA)
Figure 4. Typical normalized output optical power vs.
drive current.
125 Megabaud Versatile Link Receiver
HFBR-25X6Z Series
Description
The HFBR-25X6Z receivers contain a PIN photodiode and
transimpedance pre-amplifier circuit in a horizontal (HFBR-2526Z) or vertical (HFBR-2536Z) blue housing, and
are designed to interface to 1mm diameter plastic optical fiber or 200 μm hard clad silica glass optical fiber. The
receivers convert a received optical signal to an analog
output voltage. Follow-on circuitry can optimize link performance for a variety of distance and data rate requirements. Electrical bandwidth greater than 65 MHz allows
design of high speed data links with plastic or hard clad
silica optical fiber. Refer to Application Note 1066 for details for recommended interface circuits.
Absolute Maximum Ratings
Parameter
GROUND
4
3
2
1
VCC
GROUND
GROUND
SIGNAL
GROUND
SEE NOTES 2, 4, 9
Symbol
Min.
Max.
Unit
Storage Temperature
TS
-40
+75
°C
Operating Temperature
TA
0
+70
°C
260
°C
Lead Soldering Temperature
Cycle Time
10
s
Signal Pin Voltage
VO
-0.5
VCC
V
Supply Voltage
VCC
-0.5
6.0
V
Output Current
IO
25
mA
Reference
Note 1, 11
CAUTION: The small junction sizes inherent to the design of this component increase the component’s susceptibility to damage from
electrostatic discharge (ESD). It is advised that normal static precautions be taken in handling and assembly of this component to
prevent damage and/or degradation which may be induced by ESD.
9
Electrical/Optical Characteristics 0 to 70°C; 5.25 V ≥ VCC ≥ 4.75 V; power supply must be filtered (see Figure 1, Note 2).
Parameter
Symbol
Min.
Typ.
Max.
Unit
Test Condition
Note
AC Responsivity 1 mm POF
RP,APF
1.7
3.9
6.5
mV/μW
AC Responsivity 200 μm HCS
RP,HCS
4.5
7.9
11.5
mV/μW
RMS Output Noise
650 nm
Note 4
VNO
0.46
0.69
mVRMS
Note 5
Equivalent Optical Noise Input
Power, RMS - 1 mm POF
PN,RMS
- 39
-36
dBm
Note 5
Equivalent Optical Noise Input
Power, RMS - 200 μm HCS
PN,RMS
-42
-40
dBm
Note 5
-5.8
dBm
5 ns PWD
-6.4
dBm
2 ns PWD
-8.8
dBm
5 ns PWD
-9.4
dBm
2 ns PWD
Ω
50 MHz
PR = 0 μW
Peak Input Optical Power 1 mm POF
PR
Peak Input Optical Power 200 μm HCS
PR
Output Impedance
ZO
DC Output Voltage
VO
Supply Current
ICC
Electrical Bandwidth
BWE
Bandwidth * Rise Time
30
0.8
65
1.8
2.6
V
9
15
mA
125
MHz
0.41
Hz * s
Note 6
Note 6
Note 4
-3 dB electrical
Electrical Rise Time, 10-90%
tr
3.3
6.3
ns
PR = -10 dBm
peak
Electrical Fall Time, 90-10%
tf
3.3
6.3
ns
PR = -10 dBm
peak
PWD
0.4
1.0
ns
PR = -10 dBm
peak
Note 7
%
PR = -10 dBm
peak
Note 8
Pulse Width Distortion
Overshoot
4
Notes:
1. 1.6 mm below seating plane.
2. The signal output is an emitter follower, which does not reject noise in the power supply. The power supply must be filtered as in Figure 1.
3. Typical data are at 25°C and VCC = +5 Vdc.
4. Pin 1 should be ac coupled to a load ≥ 510 Ω with load capacitance less than 5 pF.
5. Measured with a 3 pole Bessel filter with a 75 MHz, -3dB bandwidth.
6. The maximum Peak Input Optical Power is the level at which the Pulse Width Distortion is guaranteed to be less than the PWD listed under
Test Condition. PR,Max is given for PWD = 5 ns for designing links at ≤ 50 MBd operation, and also for PWD = 2 ns for designing links up to 125
MBd (for both POF and HCS input conditions).
7. 10 ns pulse width, 50% duty cycle, at the 50% amplitude point of the waveform.
8. Percent overshoot is defined at:
(VPK - V100%)
––––––––––––
 100%
V100%
9. Pins 5 and 8 are primarily for mounting and retaining purposes, but are electrically connected. It is recommended that these pins be connected to ground to reduce coupling of electrical noise.
10. If there is no input optical power to the receiver (no transmitted signal) electrical noise can result in false triggering of the receiver. In typical
applications, data encoding and error detection prevent random triggering from being interpreted as valid data. Refer to Application Note 1066
for design guidelines.
11. Moisture sensitivity level (MSL) is 4
10
Figure 1. Recommended power supply filter circuit.
Figure 2. Simplified receiver schematic.
Figure 3. Typical pulse width distortion vs. peak input
power.
11
Figure 4. Typical output spectral noise density vs.
frequency.
Figure 5. Typical rise and fall time vs. temperature.
Versatile Link Mechanical Dimensions
HORIZONTAL MODULES
HFBR-1527Z
HFBR-2526Z
HORIZONTAL MODULES
HFBR-1537Z
HFBR-2526Z
2.03
(0.080)
6.86
(0.270)
10.16
(0.400)
18.8
(0.74)
0.64
(0.025)
2.03
(0.080)
5.08
(0.200)
3.81 (0.150) MAX.
3.56 (0.140) MIN.
6.86
(0.27)
4.19
(0.165)
7.62
(0.30)
7.62
(0.300)
5.08
10.16 (0.200)
(0.400)
18.80
(0.740)
0.51
(0.020)
1.27
(0.050)
2.54
(0.100)
0.64 (0.025) DIA.
1.85
(0.073)
2.77
(0.109)
Versatile Link Printed Circuit Board Layout Dimensions
TOP VIEWS
HORIZONTAL MODULE
7.62
(0.300)
2.54
(0.100)
TOP VIEW
VERTICAL MODULE
1.01 (0.040) DIA.
4 3 2 1
5
7.62
(0.300)
PCB EDGE
8
1.85 MIN.
(0.073)
DIMENSIONS IN MILLIMETERS (INCHES).
For product information and a complete list of distributors, please go to our website:
www.avagotech.com
Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries.
Data subject to change. Copyright © 2005-2012 Avago Technologies. All rights reserved. Obsoletes 5989-4631EN
AV02-1502EN - April 11, 2012
18.29
(0.720)